Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 310/444 | < Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >

• access VPN machine macosx same subnet

  - by matheszabi

  I would like to access the office machine, which has a fixed IP, and is available only in its local LAN. Let say 192.168.1.100. I have a VPN with username/password connection and I am trying to access the office machine from another location, i.e., another LAN, which has the same subnet: 192.168.1.50. I am using MacOSX 10.8. I have checked the "send all trafic over VPN connection, but I think it looks like it doesn't care and is searching in Local. I do not have admin privileges and can't request to make changes to the network settings in both LANs. Is there any way to connect to the desired remote machine?

  Read the article

• Routing table change to access Internet over mifi

  - by Randall Blake

  I have two networks at home. One uses a Verizon mifi wireless on 192.168.1.1. The other uses a dlink router on 192.168.0.1. I have one laptop with two nics, one wireless and one not. The wireless nic connects to the mifi. The Ethernet nic connects to the dlink router. It's ip is 192.168.0.2. I also have a laptop with only one nic connected to the dlink on 192.168.0.3. I want to connect laptop 2 to the Internet. Can I do that by adding an entry to the routing table so that destination 0.0.0.0 routes to 192.168.0.2? If I do that, will laptop 1 "know" that it should route traffic from 192.168.0.3 to 192.168.1.1? Thanks for any assistance.

  Read the article

• Cached Network Share Credentials?

  - by Brian Wolfe

  Hi, I have an issue in Windows 7 where I get the following error message when attempting to access an admin network share on a machine in another domain: "Multiple connections to a server or shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again." Troubleshooting I've Done Start Run cmd net use * /DELETE Start Manage Windows Credentials Deleted all credentials I still receive the same error until I reboot my machine. After I reboot, it works fine. However, I am able to log into the admin share if I hit it by it's IP address. QUESTION My question is, is there somewhere else I should be looking for cached user credentials? Thanks, Brian

  Read the article

• Windows 7 stopped connecting to samba share

  - by Jan

  I have a problem with Windows 7 Home connecting to samba on linux server. It's worked fine for a year and without any changes in configuration or updates it suddenly stopped working. The strangest thing for me is that it stopped working for no reason that I could think of. After a few minutes after trying to connect I get: \\ip is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Other computers in that network (XP machines) connect to samba without any problem. I've tried adding LmCompatibilityLevel as described here: http://www.tomshardware.com/forum/75-63-windows-samba-issue , but it didn't help.

  Read the article

• UDP Reverse Proxy

  - by user180195

  I have found a way to make reverse-proxy to an external IP. Here is how someone making a request will see it's request being passed: Clients sends request Request reaches the Datacenter one in some place That datacenter, acting as a reverse proxy will redirect the same exact request to another datacenter. The datacenter will then process the request Although, this only works with TCP/HTTP (Looking currently at HaProxy). I am hosting game servers at the other datacenter (where the proxy is not) that are using UDP protocol. Do you know how can I setup a reverse proxy using the UDP protocol.

  Read the article

• Point example.com to webserver in DNS record

  - by ggstevens

  I have a Mac Mini Server (named Server) with the following DNS setup Primary Zone: example.com mysql-host.example.com machine (10.0.0.101) server.example.com machine (10.0.0.100) server.example.com nameserver (10.0.0.100) www.example.com machine (10.0.0.102) www.example.com is a linux box with Apache. How do I get both example.com and www.example.com to work. Right now, I can view my website with www.example.com only. I know there's nothing that points example.com to the IP, but when I create a machine record without a hostname I get an error (This machine record cannot be created without a host name.).

  Read the article

• How to route traffic through a specific SOCKS proxy on a per-app basis?

  - by GJ.

  I'm running a certain desktop app (actually via AIR if it makes any difference) which doesn't have any built-in proxy configuration settings. I need to get all traffic just from this app directed through a secure SOCKS proxy. This implies I can't use the global network preferences, as these would affect many other apps. Is there any way to force all network communication through a given SOCKS proxy on a per-app basis? It would also be helpful to know if there's a way to perform such routing globally, based on specific IP addresses (as this could allow for some reasonable workaround).

  Read the article

• Cannot access to any Windows share including localhost

  - by user21936

  I can't access any share from my operating system, including \\localhost and \\127.0.0.1. I have Windows 7. NetBIOS over IP is enabled, other computers in the network can access my shares and other computer's shares, but my operating system cannot access any share. I have installed Windows XP within VMware, and the virtual Windows XP can access all shares including the host shares. I can communicate in other ways like TCP, HTTP and gaming, but not access shares. How to solve this problem?

  Read the article

• Routing traffic to specific web sites through Ethernet, rest via wifi on Mac OS X 10.6?

  - by user32448

  Hi I have two separate Internet connections connected to a Mac and I'd like one of them (via Ethernet eth0 gateway 192.168.2.1) to serve for just backing up to an remote online storage, and the other one (via Airport en1 gateway 192.168.1.1) for all other Internet traffic. I tried using "route" from the terminal as follows: sudo route add -host 98.207.226.113 -interface eth0 (just for testing against the site www.whatismyip.org whose IP is 98.207.226.113, to see through which gateway the traffic is routed) I can see using netstat that the route is added: $ netstat -rn -f inet Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 49 0 en1 98.207.226.113 192.168.2.1 UGSc 0 0 eth0 However, the traffic in this case does NOT get routed properly through Ethernet, as if the routing definition I made is ignored. Any ideas? Thanks!

  Read the article

• Where is debian storing its network settings?

  - by user13743

  I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

  Read the article

• Security measures for CentOS

  - by cappuccinodrinker

  I have been tightening up my web server security and wanted to know what else I can do. I am running CentOS 5 with these measures: - All passwords to FTP, MySQL etc are generated from grc.com/passwords.htm and microsoft.com/protect/fraud/passwords/create.aspx (for the ones which cannot be too long). - Running iptables with all ports shut off except for http mail and smtp, the important ports like FTP SSH are blocked to all except my static office IP. There is also no response to pings. - Rootkit Hunter running daily - The server is PCI compliant according to Comodo - Not running any crappy made php apps, we use Zend Framework for our stuff and do have kayako installed and keep them up to date. Can't really think of anything else I can do... I could implement a brute force measure, but I think I already have by simply changing my SSH port to a number above 10000 and blocking it off with iptables.

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• "DNS not responding" error with D-Link router and PPTP internet connection

  - by Born2win

  I have a D-Link DIR-615 router since around six months. My internet connection is VPN (PPTP) based, i.e. I have been given a username and password from my ISP and my IP address is dynamic. Since a few days I am experiencing a serious problem. My router connects normally (I can see the yellow light), but my computer is giving me a "DNS not responding" error. I have tried everything (reset, reboot etc.) but no success.

  Read the article

• Xmail shows error at Gmail

  - by Karthik Malla

  Hello I am using Xmail server at IP 65.75.241.26 hosted at www.softmail.me using which I can send and receive email to/from all email service providers but unable to receive back from Gmail. This error lies only with Gmail. Experts says that Gmail requires proper working MX records where as for other emailing providers do not bother much. Is MX records the solution for my problem? Or is there any other issue? My mailserver outgoing at softmail.me:25 My mailserver incoming at softmail.me:110 Please help me how to get rid of this issue.

  Read the article

• Is Winpcap able to capture all packets going through a Gigabit NIC without missing any packets?

  - by Patrick L

  I want to use Winpcap to capture all network packets going through a Gigabit NIC of a server. Assuming that I am able to utilize the network link up to 100%, the maximum network speed is 1000Mbps. If we exclude the TCP/IP headers, the maximum TCP data rate should be roughly 940Mbps. Let's say I send a 1GB file through the NIC at 940Mbps using TCP destination port 6000. I use Winpcap to capture all network packets going through the NIC and then dump it to a pcap file. If I use Wireshark to analyze the pcap file and then check the sum of packet size for all network packets sent to TCP port 6000, am I able to get exactly 1GB from the pcap file? Thanks.

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Grant relay to servers based on AD security group membership

  - by john

  We're moving our relay from an Exchange 2003 server to an Exchange 2010 server. I was hoping the "Grant or deny relay permissions to specific users or groups" option would still be available in some form, but I can't find out how to do it. I've read up on recieve connectors and so far I can't get it to work. I have edited the security on the Recieve Connector to allow the following extended rights to the group and added computer accounts to that group: Accept Routing Headers Bypass Anti-spam Submit to Server Accept any Sender Accept any Recipient Then I suddenly realised while testing... How would the receive connector resolve the permission to a particular AD object, maybe a reverse DNS lookup? What I'd like to know is if what I'm trying to achieve is possible, and how it would be possible. I would rather not revert to an IP-based list as this is not as manageable, and I'm trying to avoid creating static IPs/reservations for a number of workstations that would otherwise not need them.

  Read the article

• Destination host unreachable, but the errorlevel is 0 (from a win7)

  - by Doron

  From a windows 7 machine, I ping a non existing ip address. C:ping 192.168.1.222 Pinging 192.168.1.222 with 32 bytes of data: Reply from 192.168.1.222: Destination host unreachable. Reply from 192.168.1.222: Destination host unreachable. Reply from 192.168.1.222: Destination host unreachable. Ping statistics for 192.168.1.222: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss) Even though there is no reply, the errorlevel is set to 0. *what I am trying to do, is figure out if a remote machine is replying to ping. One of my test is to turn off the machine and ping it. For some reason, ping sets errorlevel to 0 *

  Read the article

• Samsung i780 networking problem

  - by Infinity

  Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

  Read the article

• Windows Server 2003/Exchange 2007: How to setup public domain mail.foo.com to route to internal exch

  - by ryan.keeter

  Good day, I have an internal Exchange Server 2007 and a Windows Server 2003 domain. At this point in time I have an external DNS setup (DynDNS 29.95 service) to resolve foo.com to my singular public IP address then it gets routed to external facing site. I would like to know how to setup POP on mail.foo.com and SMTP on smtp.foo.com, and more importantly, what needs to be setup in Exchange server to allow for this to happen. My end state is to send email through smtp.foo.com and receive mail on mail.foo.com. As of now, when I create a user within Exchange the default email address is [email protected], and I would like it to be [email protected]. Thank you and I appreciate the help as I am a .NET developer trying to do sys admin work, and it is MUCH harder than I have ever imagined, my hat is off to all sys admins and IT pros.

  Read the article

• Linksys WRT54GS V6 Router Blinking Power Light

  - by Frank

  I have a Linksys WRT54GS V6 Router in my possession got it at my local goodwill for 5$. Upon start up the Power LED starts flashing like crazy and at the same time the Ethernet ports all light up once then turn off (DMZ and WLAN never turn on). I can ping the router only by setting a static IP on my Pc. I can also successfully push a file (official Linksys OS and DD-wrt) into it via TFTP but this currently does nothing (no 192.1681.1 Access). Any ideas as to what may be wrong? I think its pretty obvious that it's bricked but.. I keep hearing a whole lot of "if it pings it's fixable" on the internet.

  Read the article

• Publishing and setting permissions to a Linux share to AD

  - by blsub6

  I have a Linux share that I want to publish to users on my Active Directory domain. I'd like to be able to control the permissions to access that share using security groups. So say I have a share named "Share" on my Linux machine named "Linux" with IP address 192.168.1.2. I publish \\192.168.1.2\Share in AD and make it so that only people who are part of the "IT" security group can access it. What's to stop anyone who's not in the "IT" security group from just going to explorer and typing in \\192.168.1.2\Share or \\Linux\Share into their Explorer to access this share? Do I need to set up permissions on the Linux file server?

  Read the article

• apxs cannot install mod_cloudflare on centos

  - by Adam

  [ Linux - CentOS - Apache 2.2 - mod_cloudflare - apxs2 ] I have changed my nameservers to point to CloudFlare. The problem is that all the IP addresses are coming in as CloudFlare's. This is no good, because I have to monitor and block some specific traffic. mod_cloudflare is supposed to resolve this but I have been unable to get this installed. The command in the documentation uses apxs2. I can't figure out how to install this, or if it just means for 'apache 2.4'. I'm running 2.2.3, and I can use 'apxs'. When I run: apxs -aic mod_cloudflare.c I get the error apxs:Error: Command failed with rc=65536 Does this mean I need apxs2 or something else? How do I get mod_cloudflare working on my server? I appreciate any help, the documentation is vague and limited.

  Read the article

• Machine account authentication on Radius server

  - by O.Shevchenko

  My workstation is under Linux. I have an Active Directory domain controller + Radius server on Windows 2008. I can verify user account 'radius-01' using 'radtest' tool: $ radtest -t pap radius-01 password123 195.234.133.32 1812 password123 Sending Access-Request of id 98 to 195.234.73.2 port 1812 User-Name = "radius-01" User-Password = "password123" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 rad_recv: Access-Accept packet from host 195.234.133.32 port 1812, id=98, length=84 Framed-MTU = 1344 Framed-Protocol = PPP Service-Type = Framed-User Class = 0x537004f00000013700010200ac1c0... I have joined my Linux PC to Active Directory domain ARB-HRK using Samba: [root@shev-arb]# net ads testjoin Join is OK I can dump machine password: [root@shev-arb]# tdbdump /var/lib/samba/private/secrets.tdb { key(34) = "SECRETS/MACHINE_PASSWORD/ARB-HRK" data(15) = "yGgXJsquRnpT0g\00" } How can i authenticate my machine account on Radius server? Do anybody know any tools for this, like: radtest shev-arb$ yGgXJsquRnpT0g 195.234.133.32 1812 password123 (this command fails)

  Read the article

< Previous Page | 306 307 308 309 310 311 312 313 314 315 316 317  | Next Page >