Search Results

Search found 18244 results on 730 pages for 'controller action'.

Page 311/730 | < Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• How to get permission to create full-text index?

  - by Bill Paetzke

  I tried to create a full-text index and got this error: Msg 9967, Level 16, State 1, Line 1 A default full-text catalog does not exist in database 'foo' or user does not have permission to perform this action. FYI--I connected to the target sql server with Windows Authentication. What do I need to do in Sql Server 2005 and/or in Windows Server 2003 to get permissions? Please be thorough (assume I am a n00b). Thank you.

  Read the article

• DNS with Amazon EC2 Elastic Load Balancer

  - by user68173

  I'm told that I can't make the root of a domain (example.com) a CNAME - I have to specify an IP. Given that you can't use an IP address to point at your Elastic Load Balancer, what's the best thing to do? Currently I do this: example.com - A record to elastic IP of first server- redirects to www.example.com www.example.com CNAME to hostname of load balancer If the first server is out of action, the redirect will fail. Is there a better way to approach this?

  Read the article

• Macbook Pro keeps ejecting anything I put into the internal optical drive

  - by Wroblewski

  My hard disk crashed and I need to reinstall Mac OS X. I restart, insert the installation DVD, press c on the keyboard and the dvd ejects. I've tried different DVDs, even CDs. It's a Macbook Pro from march 2008. Is it broken? Or can it be something more severe like the firewire controller on the motherboard (since I noticed this after my hard drive started to act strangely)? I've ran Apple Hardware Test successfully.

  Read the article

• RabbitMQ - How I do configure servers for zero-downtime upgrades?

  - by Terence Johnson

  Having read through the docs and RabbitMQ in Action, creating a RabbitMQ cluster seems straightforward enough, but upgrading or patching an existing RabbitMQ cluster seems to require the whole cluster to be restarted. Is there a way to combine clustering, shovel, federation, and load balancing to make a rolling upgrade possible without losing queues or messages, or have I missed something slightly more obvious?

  Read the article

• Error! File In use: SQLSERVER

  - by Asad Butt

  I am trying to copy a database from one folder to another. There is no program at all running except operating system.(I mean all windows shut) I keep getting this : The action cannot be completed because the file is open is another program close file and try again Try again, Try again , Try again ......... what the hell on earth is holding that file and how can I carry on with copy / delete / overwrite files(DB) as this problem is something very common. Thanks

  Read the article

• Good Wireless Range Extender

  - by Joseph Sturtevant

  Can anyone recommend a good wireless (802.11g) range extender? I would like to find something that will provide reliable wireless to areas of the building that aren't covered or get poor reception. I would also like a product that won't require big changes to my current wireless setup (multiple APs with a wireless controller are out). Latency and bandwidth aren't terribly important. Does anyone have experience with a product like this?

  Read the article

• Can i run this monitor ?

  - by akshay

  I am upto buying new Monitor for mine desktop here are some specs.and you please help me choose a better one (an which one will work)? Graphics property of system : Intel(R) 82845G Graphics Controller Memory 64 MB Memory type 2 Driver version 6.13.01.3317 Monitors i think will be good is. Monitor : http://www.google.com/products/catalog?q=viewsonic+22&cid=10503070423897692907&ei=MKj_S5OGCpOgjgSghsX2CA&sa=title&ved=0CAcQ8wIwADgA&os=tech-specs

  Read the article

• Email server can send internal, but messages never arrive at external recipients

  - by Chase Florell

  I'm running MailEnable on my server, and have been for many years. Recently we had an attack on our server, and I was able to close the hole. Since then, our mail server doesn't seem to be sending mail out. If I send an email from myself to another account hosted on the server, the email arrives as expected. If I send an email from my gmail account to my business account, the email also arrives as expected The problem comes when I send from my business account to an external domain I tried the following Gmail.com Hotmail.com Shaw.ca When I send to any of the above The message leaves my client as expected, The logs appear to accept and forward on the message The SMTP outbound que is empty The message never arrives I have checked our domain with mxtoolbox.com senderbase.org And neither of them are reporting any problems with our domain. I have ensured that port 25 is open (along with the other standard ports) Here is one of the log entries from the SMTP connector 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 220 mx1.example.com ESMTP MailEnable Service, Version: 6.81--6.81 ready at 11/05/13 12:10:00 0 0 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH AUTH LOGIN 334 VXNlcm5hbWU6 18 12 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH {blank} 334 UGFzc3dvcmQ6 18 26 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH Y29sb25lbGZhY2U= 235 Authenticated 19 18 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 MAIL MAIL FROM:<[email protected]> 250 Requested mail action okay, completed 43 31 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 RCPT RCPT TO:<[email protected]> 250 Requested mail action okay, completed 43 35 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 DATA DATA 354 Start mail input; end with <CRLF>.<CRLF> 46 6 [email protected] Here are the headers of the sent message X-Assp-Version: 1.7.5.7(1.0.07) on ASSP.nospam X-Assp-ID: ASSP.nospam 78601-04523 X-Assp-Intended-For: [email protected] X-Assp-Envelope-From: [email protected] Received: from [10.10.1.101] ([68.147.245.149] helo=[10.10.1.101]) with IPv4:587 by ASSP.nospam; 5 Nov 2013 12:10:00 -0700 From: Chase Florell <[email protected]> Content-Type: text/plain Content-Transfer-Encoding: 7bit Subject: Test Message Message-Id: <[email protected]> Date: Tue, 5 Nov 2013 12:10:18 -0700 To: Chase Florell <[email protected]> Mime-Version: 1.0 (Mac OS X Mail 7.0 \(1816\)) X-Mailer: Apple Mail (2.1816) . Where else can I check to see if there is something broken? What could cause a problem like this whereby the message appears to send, but never arrives, and never returns a bounce?

  Read the article

• small IIS web farm-create an Active Directory domain or no?

  - by brian b

  We have a smallish web farm of < 5 Windows 2008 servers. Some do data, most do IIS hosting. Is it a good/bad idea to set up a domain controller and put all in the same "production" domain? We want to avoid a world where we have to sync multiple admin passwords between the boxes (or share admin credentials among the team). Presumably, the DC would be just another VM, so hardware cost doesn't enter into the discussion.

  Read the article

• How to Reinstalling MSSQL Server 2008 with SP1? (Windows 7)

  - by n10i

  I am using Windows 7 Ultimate x64. I had earlier installed SQL server 2008 with SP1 with Visual Studio 2008 Team System with sp1. Now that VS2010 is out I wanted to install it so I uninstalled visual studio then MSSLQ Server 2008 SP1 and then SQL Server 2008 as suggested here: h**p://mark.michaelis.net/Blog/SQLServer2008InstallNightmare.aspx But now when I try to reinstall it I am unable to get it right I am getting the ERROR: “Attempted to perform an unauthorized operation.” (Following is part of the log file): 2010-04-16 04:54:57 Slp: Sco: Attempting to replace account with sid in security descriptor D:(A;CI;KR;;;S-1-5-21-2213424280-2581054173-1939225444-1027) 2010-04-16 04:54:57 Slp: ReplaceAccountWithSidInSddl -- SDDL to be processed: D:(A;CI;KR;;;S-1-5-21-2213424280-2581054173-1939225444-1027) 2010-04-16 04:54:57 Slp: ReplaceAccountWithSidInSddl -- SDDL to be returned: D:(A;CI;KR;;;S-1-5-21-2213424280-2581054173-1939225444-1027) 2010-04-16 04:54:57 Slp: Prompting user if they want to retry this action due to the following failure: 2010-04-16 04:54:57 Slp: ---------------------------------------- 2010-04-16 04:54:57 Slp: The following is an exception stack listing the exceptions in outermost to innermost order 2010-04-16 04:54:57 Slp: Inner exceptions are being indented 2010-04-16 04:54:57 Slp: 2010-04-16 04:54:57 Slp: Exception type: Microsoft.SqlServer.Configuration.Sco.ScoException 2010-04-16 04:54:57 Slp: Message: 2010-04-16 04:54:57 Slp: Attempted to perform an unauthorized operation. 2010-04-16 04:54:57 Slp: Data: 2010-04-16 04:54:57 Slp: WatsonData = Microsoft SQL Server 2010-04-16 04:54:57 Slp: DisableRetry = true 2010-04-16 04:54:57 Slp: Inner exception type: System.UnauthorizedAccessException 2010-04-16 04:54:57 Slp: Message: 2010-04-16 04:54:57 Slp: Attempted to perform an unauthorized operation. 2010-04-16 04:54:57 Slp: Stack: 2010-04-16 04:54:57 Slp: at System.Security.AccessControl.Win32.GetSecurityInfo(ResourceType resourceType, String name, SafeHandle handle, AccessControlSections accessControlSections, RawSecurityDescriptor& resultSd) 2010-04-16 04:54:57 Slp: at System.Security.AccessControl.NativeObjectSecurity.CreateInternal(ResourceType resourceType, Boolean isContainer, String name, SafeHandle handle, AccessControlSections includeSections, Boolean createByName, ExceptionFromErrorCode exceptionFromErrorCode, Object exceptionContext) 2010-04-16 04:54:57 Slp: at Microsoft.SqlServer.Configuration.Sco.SqlRegistrySecurity..ctor(ResourceType resourceType, SafeRegistryHandle handle, AccessControlSections includeSections) 2010-04-16 04:54:57 Slp: at Microsoft.SqlServer.Configuration.Sco.SqlRegistrySecurity.Create(InternalRegistryKey key) 2010-04-16 04:54:57 Slp: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.SetSecurityDescriptor(String sddl, Boolean overwrite) 2010-04-16 04:54:57 Slp: ---------------------------------------- 2010-04-16 10:37:19 Slp: User has chosen to cancel this action 2010-04-16 10:37:19 Slp: Watson Bucket 2 Original Parameter Values 2010-04-16 10:37:19 Slp: Parameter 0 : SQL2008@RTM@ 2010-04-16 10:37:19 Slp: Parameter 2 : System.Security.AccessControl.Win32.GetSecurityInfo 2010-04-16 10:37:19 Slp: Parameter 3 : Microsoft.SqlServer.Configuration.Sco.ScoException@1211@1 2010-04-16 10:37:19 Slp: Parameter 4 : System.UnauthorizedAccessException@-2147024891 2010-04-16 10:37:19 Slp: Parameter 5 : SqlBrowserConfigAction_install_ConfigNonRC 2010-04-16 10:37:19 Slp: Parameter 7 : Microsoft SQL Server 2010-04-16 10:37:19 Slp: Parameter 8 : Microsoft SQL Server 2010-04-16 10:37:19 Slp: Final Parameter Values I have googled around for the error given error but all I could find is to regedit and reset permissions on certain reg keys but I don’t see any reg keys with access problem in the log file the log file can be download here: http://www.mediafire.com/?dznizytjznn. Please guys help me out here I am a developer and I cannot afford an OS reinstallation! Thanks in advance…

  Read the article

• System Event ID 11 Disk

  - by Guy Thomas

  Upon starting Windows Server 2008 R2 I get this error message: Event ID 11 Disk The driver detected a controller error on \Device\Harddisk3\DR3. There are also also 3 more similar messages for Harddisk 2, 4, and 5, but not zero or 1. Checking the event viewer reveals it's been going on for 3 months. I ran chkdsk - no bad sectors. Any advice on the cause, better still, a solution?

  Read the article

• No architecture vs architecture-specific binaries

  - by Aaron

  From what I understand, the noarch suffix means that it's architecture independent and should work universally. If this is the case, why should I install architecture-specific packages at all? Why not just go straight for the noarch? Are there optimizations in the x86 or x64 binaries that aren't found in the noarch binaries? What's best for high performance applications? Folding@Home does this with their controller:

  Read the article

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• Conditional formatting with date and time

  - by Kiran

  I have a problem on conditional formatting with date and time. I hava a cell A1 that has date and time and I want to conditionally format its adjecent cell if the value of cell A1 is greater than 3 days compared to today, then cell A2 should show as "Follow-up Required" and cell colour should turn red no. if cell value of A1 is less than 3 days compared to today, no action is required. Please help. Regards, Kiran

  Read the article

• Delay after commit before Redmine comments ticket

  - by Paul

  I was used to having a post-commit hook trigger processing of the commit message by Trac (SVN repository). The comment (or action) was added immediately. Now I switched to Mercurial as a VCS and Redmine as a ticketing system. Redmine does recognize information in changeset/commit messages like "refs #185" - but it takes several minutes to appear in the ticket. Any ideas why this is? Is the routine to grab the changesets called periodically somehow?

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubu

  - by user37968

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• VMware or Xen support for AIX on pSeries architecture

  - by A.Rashad

  I tried to find an explicit confirmation on VMware website if there is any chance we could virtualize AIX running on pSeriese architecture (P5, P6 and P7), but in vain. so far we have only one product available which is PowerVM (IBM Product) but we are trying to find alternative solutions to evaluate pros and cons before taking any action. Even Xen mentions the support for Power PC but for Linux not AIX. I hope someone could give an insight on this matter.

  Read the article

• perf tuning for ESX vmfs3 on RAID

  - by maruti

  looking for recommendations on ESX4 OS - VMFS version3: RAID-5 : matching the stripe size with VMFS block size? (64K, 128K etc) RAID controller options: "adaptive read ahead, write-back" on PERC 6i 90% VMs on server are Windows (2008, 2003, Vista etc, SQL 2005 etc) i have read that smaller stipes are good for writes and larger for reads. Since this is virtual env, not sure whats good.

  Read the article

• SSD with multiple partitions - disk life implications

  - by Nicolas Webb

  Each block on a SSD has a finite number of writes. This is mitigated on modern drives by "spreading" the writes around as you use the drive. I'm wondering if you partition a SSD into several partitions (a Mac using Boot Camp, for example) if this measure is defeated somewhat - can the writes be spread across the entire drive? Or are they contained strictly within the partition boundaries? Any SSD controller engineers here :)?

  Read the article

• Passenger 2.2.4, nginx 0.7.61 and SSL

  - by boompa

  Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

  Read the article

• SharePoint domain authentication

  - by JL

  I have a local domain controller setup, which is MYDOMAIN.com, and on a seperate local server I have a MOSS site running. the DNS is all working fine but when I try to connect to the MOSS site using domain credentials I can't use syntax: MYDOMAIN/MyAccount it is expecting [email protected] What can I do to fix this issue, so I have normal domain login capabilities like every other sharepoint site out there?

  Read the article

• WINDOWS - Deleting Temporary Internet Files through Group Policy

  - by Muhammad Ali

  I have a domain controller running on Windows 2008 Server R2 and users login to application servers on which Windows 2003 Server SP2 is installed. I have applied a Group Policy to clean temporary internet files on exit i.e to delete all temporary internet files when users close the browser. But the group policy doesn't seem to work as user profile size keeps on increasing and the major space is occupied by temporary internet files therefore increasing the disk usage. How can i enforce automatic deletion of temporary internet files?

  Read the article

• HP UX can not boot from Ignite Tape

  - by Spirit

  We have hp rp2470 server running hp-ux 11.00, with LVM mirroring. As for redundancy we have second rp2470 same hw (same two processors, same ram, same two hdd’s, same number of lan cards). I want to clone first one to the second. For that purpose I am making ignite tape with the following command: make_tape_recovery -x inc_entire=vg00 Ignite tape finishes without problems. When I boot second server from this ignate tape, server is starting to boot, and ignite restore finishes without any errors, only few notes, which are normal. However vmunix is not booting and when restore finishes, it boot to ISL prompt. From this I cannot boot /stand/vmunix. I tried to run recovery shell but no success. When recovery shell ask to do frecover to restore critical files, then I receive error: frecover(5405): unable to open /dev/rmt/0m At first I thought that the problem might be in the difference of the firmware version of the servers: fw version of production server is: Firmware Version 43.50 and fw version of backup server is: Firmware Version 42.19 So i did a fw upgrade of my backup server so that both servers are v43.50, and tried a recovery but again cant boot the system. Next I did another archive tape with -I (Interactive) flag: make_tape_recovery -I -x inc_entire=vg00 and tried recovery with it, again no good. I cannot find any error or warnings on ignite log, and I cannot boot hpux. I am only on ISL prompt. This is what i've noticed on the gsp logs: ************* SYSTEM ALERT ************** SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:18:49 ALERT LEVEL: 6 = Boot possible, pending failure - action required REASON FOR ALERT SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF ON ON ON LED State: Boot Failed. Running non-OS code. Check Chassis and Console Logs for error messages. 0x00000060860010B0 00000000 00000000 - type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A1231 - type 11 = Timestamp 07/27/2003 10:18:49 And another gsp log: Log Entry # 3 : SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:12:20 ALERT LEVEL: 6 = Boot possible, pending failure - action required SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail CALLER ACTIVITY: 1 = test STATUS: 0 CALLER SUBACTIVITY: 0B = implementation dependent REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00 0x00000060860010B0 00000000 00000000 type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A0C14 type 11 = Timestamp 07/27/2003 10:12:20 Type CR for next entry, - CR for previous entry, Q CR to quit. Please note that I can not change anything on the production server. I can only make changes to the backup server. Any help is appreciated.

  Read the article

• Web Farm Framework - Adding servers are offline

  - by Johan Wikström

  My problem is that im trying to setup a server farm but the nodes all come up as offline. I dont get a connection error saying that the servername is wrong, but get "offline" after it "test connection" I have: - Setup firewalls rules to allow Remote and file share on Domain and private network - Installed WWF 2.0 on both servers - Account that im using is a domain account that is Administrator on both machines. www01 is the same server as the controller below, but same results if i try www02 as primary. Any ideas?

  Read the article

< Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >