Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 312/1221 | < Previous Page | 308 309 310 311 312 313 314 315 316 317 318 319  | Next Page >

• Split horizon, route filtering, and having RIPv2 announce a non-attached route to host...

  - by Paul

  Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

  Read the article

• Configuring Ubuntu for Global SOCKS5 proxy

  - by x50

  Does anyone know the best way to configure Ubuntu to use a SOCKS5 proxy for all network traffic? Server is ubuntu server - all cli. So I cannot set via the Proxy Settings GUI. We want to push all outbound traffic through the proxy (apt-get, http, https, etc). I do need to separate ssh traffic so it stays locally. Everything else should hit the proxy server. not that it matters, but I'm using Squid for the proxy server. I know this is easy on Mac and Windows as you can set a proxy on the actual network interface. Can you do the same on Ubuntu?

  Read the article

• Cisco QoS Guidence

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future.

  Read the article

• d-link 4500 - Not visible in tracert

  - by dbasnett

  I can ping my router (192.168.1.1), but it does not show up in the tracert. My router is a d-Link 4500 v1.22. Is it some config item I have missed?

  Read the article

• Free IP address management software

  - by TiFFolk

  We are choosing a system for managing our IP address space. So we are looking for a special free software like IPPlan. So what we have nowadays: Ipplan (Beta IPv6 support) SolarWinds IP address tracker (IPv6 support unknown ) IP module of The NOC Project (BTW, take a look of it, seems to be very promising project) (IPv6 support unknown ) phpIP (Does not support IPv6) IP management from RackTables (Does not support IPv6) Do you know about any other special software, like written above? But: No Wiki No DNS No DHCP No spreadsheet Software should provide: Clear view of available addresses Detail listing of all addresses by subnets/search pattern/owners/additional info It must support adding additional info like owner of IP, domain-name, contacts, etc Multi user support Easy interface Software has to be specially written for address management. Scalability Any OS: win, lin, sol, web

  Read the article

• Best security practice for small networks - wifi, lan,

  - by Grimlockz

  We regularly setup small networks for clients in different locations to allow them to work on different products now the question what should be the best security practice. Currently we have a wifi enabled with WPA2 and most laptops connect to this but some will connect to a cabled switch connecting to the router. We are thinking on what we should do to increase the security on our small networks - We do have have security on the laptops so you can share directly to the other persons drive by a simple Windows user account. Some suggestions are: We get a LAN switch with ACL control and mac filtering for the hard wired connections? We get acl working on the wifi via a good Cisco router? ipSec policies on all machines? IP filtering and fixed IPs? I suppose people are worried that anyone can plug into the switches and get the access to the network . Summary: Maintain a level of decent security that can be replicated easily to every setup that we do for clients

  Read the article

• Windows 8 - no internet connetction to some hosts while VPN is active

  - by HTD

  I use VPN to access the servers at work. When VPN is used, all network traffic to the Internet passes through my company network. It worked without any problems on Windows 7, now on Windows 8 some sites suddenly became inaccessible. Please note - I don't try to connect them over RDP, they are public Internet addresses, outside company network. They are inaccessible using any protocol. Ping returns "General failure.". I know it could be a misconfiguration on my company's server side, but it's very strange, since the same VPN connection used on Windows 7 works properly. What's wrong? Is it a Windows 8 bug, or is there something I could do on my company servers to make VPN work as expected with Windows 8? My company network works on Windows Server 2008 R2 and uses Microsoft TMG firewall. I couldn't find any rules blocking the traffic to mentioned sites, all network traffic for VPN users are passed through for all IPs and protocols. Any clues? UDPATE: Important - one whole day it worked. I hibernated and restarted the computer, connected and disconnected VPN - nothing could break my connection. Today it broke again, and restarting Windows didn't help. And now the solution: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.1.1 Oh, OK, I know what it did, added my default gateway to routing table. But it still didn't work sometimes. So I removed my main network gateway route with: route delete -p 0.0.0.0 MASK 0.0.0.0 192.168.0.1 And added modified with: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.0.1 And it works. Now. But I don't trust this. I don't know what really happened.

  Read the article

• Windows 7 - Sharing a connection through WiFi?

  - by RadiantHex

  Hi folks, I have a PC with Win7 and an iPod touch. Win7 is connected to the internet through a 3G dongle, I have set up an Ad Hoc wifi network and ticked "Allow other network users to connect through this computer's Internet connection". I have connected to both networks, but I'm getting "No Internet access" as access type for the Ad Hoc connection. Any ideas?

  Read the article

• Vista: "connect to a network" does not load (can't set up VPN)

  - by Arkaaito

  I'm trying to connect to my office VPN from home. One small problem: my home desktop uses Vista (64-bit, Ultimate edition). On Vista, you're supposed to set up a VPN like so: Open the control panel Click on Network Click on "Connect to a Network" Configure a new connection of type "Office" The problem is, when I click on the link for "Connect to a Network", nothing happens. Can anyone suggest how I should go about troubleshooting this? (Or am I better off just upgrading to Windows 7?)

  Read the article

• How do I "telnet into [my] favourite Web server"?

  - by rookie

  I'm reading a book about programming, and I want to check an HTTP response message. The book is instructing me to telnet into your favorite Web server. Then type in a one-line request message for some object that is housed on the server: for example: telnet cis.poly.edu 80 GET /~hello/ HTTP/1.1 Host: cis.poly.edu What am I supposed to do, exactly? What program do I need? Where do I need to type this message?

  Read the article

• Finding cause of TCP retransmission within a LAN

  - by Surreal

  Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

  Read the article

• Route traffic from one VPN to a second VPN

  - by Dominic

  I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

  Read the article

• Disable Windows Update when on 3G network

  - by David Gardiner

  Are there any tools/utilities that will change Windows Update to not download when a machine is using a 3G-type wireless network connection? Not sure if there is any difference between using a 3G USB key and a tethered iPhone.

  Read the article

• DNS server at router level vs. computer level

  - by Craig

  I've three questions. Is it better/faster/optimal to set up your server's preferred and alternate DNS servers in your OS's network settings or in your router settings? Will it cause problems if it is set up in both places, both pointing to the same IPs? I am running Windows and I have my network assign a static IP to one of my computers. This doesn't allow me to obtain the DNS server addresses from my router automatically. Is there an IP I can put in that will cause it to take the DNS server addresses from the router?

  Read the article

• What's Switched LAN Topology ?

  - by mgpyone

  If somebody can tell me clearly what "Switched LAN Topology"is, it'll be great. I can't even understand what it's due to the following picture . Any answers are most welcome.

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Block spam by using geoip filter?

  - by faultyserver

  We are looking for a way to be able to block spam based on geographic location by filtering using geoip. context: we rarely have any email correspondence outside of the USA, so we would like to block all incoming email outside the US except for maybe one or two countries. After a little Googling I have found a couple of solutions that may work (or not), but I would like to know what other sysadmins are currently doing or what they would recommend as a solution. Here is what I have found so far: Using PowerDNS and its GeoIP backend it is possible to use geoip for filtering. Normally this backend is used to help distribute load as a kind of load balancing but I dont see why it couldnt be used to kill spam as well? Possibly use the Maxmind lite country database and some scripting to do a similar job. Ideally what I am looking for is a solution that would handle decent load and scale well too...aren't we all! ;) Thanks in advance for your help! :-)

  Read the article

• Wireless 802.11x Disconnects

  - by BillP3rd

  I've looked at (and read) all of the similar questions and none of them get exactly to the issue I'm having at home. I have an 802.11g access point (two, actually, with different SSIDs and on different channels). One is an Airlink AR525W. The other is a Linksys WRT54G v.2. The issue is that at random times, my laptop will lose its wireless connection. This occurs regardless of which access point I'm connected to. When I lose the connection, the affected AP no longer appears in the list of available APs. Also, it doesn't have anything to do with walls or distance. It can happen within 30' and when my laptop is literally within line-of-sight. When it loses the signal, it can take from 10 to 30 minutes to reconnect and it always will without intervention. I've done all the “standard” things to troubleshoot the problem and it has improved. For example, I surveyed other access points in my vicinity and have selected a different channel for each of my APs that no one else nearby is using. Both APs are configured WPA2/AES. I'm down to wondering [Note: This is not a shopping question. I'm not buying a new AP] if the fact that I didn't drop two bills on my APs and instead opted for more modest solutions has anything to do with it? I've oft wondered why anyone would go for the high-end AP when they didn't have to. Also, I am aware of DD-WRT and have chosen not to go there because only one of my APs is supported. Oh, and one final thing. It an HP x64 laptop running Windows 7 Ultimate. The wireless interface is an Atheros AR9285 802.11b/g/n WiFi Adapter. All the latest drivers and service packs have been applied. It did the same thing with my old laptop (a Lenovo) so I don't the problem is in the laptop. It's really annoying when this happens and suggestions of things I haven't thought of or may have overlooked (No, really. As unlikely as it is, I admit that I may have overlooked something :-)) are appreciated.

  Read the article

• static routes, cisco ASA, remote locations

  - by Jeff

  192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

  Read the article

• Setting up a proxy for FTP - Windows

  - by RadiantHex

  Hi folks, I have 2 windows machines and a server. 1 is my laptop, the other is a workstation that the IP of which is white-listed on the server. The laptop has a dynamic IP, so the IP cannot be white-listed. I would like to be able to perform FTP transfers from my laptop to the server, while using the workstation as a proxy. Both machines are using Windows 7. Is this possible? Help would be amazing!

  Read the article

• Are there any security concerns when using Windows' default workgroup?

  - by koiyu

  Are there any security concerns one should be aware of if you're using Windows' default workgroup as the workgroup? (Or is worrying just tinfoiling?) Should it be commonplace to rename the workgroup to something personal/unique after Windows installation? Are there any other benefits in renaming the workgroup from the default besides making it to look more describing? Ie. is renaming worth the hassle as it makes the workgroup generally less accessible? It is used in local area network after all.

  Read the article

• How to discover if a specific address/port is reachable?

  - by marco.ragogna

  I need a simple utility that allow me to check if a PC, attached to a local network, is able to reach a specified address:port using specified protocol like TCP or UDP Machine's OS I will use to do the check is Windows XP. Can you help me, please?

  Read the article

• OS X 10.6 won't automatically connect to wireless even though remember network is checked

  - by Hendy

  Upgraded to 10.6 recently. 10.5 would connect to my home network whenever I was home. 10.6 constantly pops up the network selection dialog and asks me what network I want to join. I click my home network and the password is already entered (so it "remembers" the network). "Remember network" is checked... but it does it every time. How do I get 10.6 to connect to networks automatically whenever it sees them?

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• Network Printers

  - by Jack

  We have a sever that shares all the printers. The PC's that are running on XP professional get a error message quoting (Connect to Printer). The only way I can find to get around the problem is by restating the printer and as soon is it comes online you can then add it but you have not got long. do you think it could be anything to-do with updates on the sever? the sever system is running Windows Server 2003 any help would be much appreciated. Thanks

  Read the article

< Previous Page | 308 309 310 311 312 313 314 315 316 317 318 319  | Next Page >