Search Results

Search found 30569 results on 1223 pages for 'computer problems'.

Page 317/1223 | < Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >

• Hard drive clicking noise on Acer AO722

  - by Blank

  I'm running Ubuntu 11.10 on an Acer Aspire One 722. Whenever I'm on battery power I get a clicking sound from my hard drive every 5 seconds or so (this does not happen when the laptop is plugged in). I'm dual booting with Windows 7 and I don't get the clicking sound in Windows. The clicking sound stops when I run the command:sudo hdparm -B 254 /dev/sda Also, according to:sudo smartctl -H /dev/sda my hard drive is healthy. Is this clicking sound something I can just ignore? Or is it a serious problem and will it eventually damage my computer? If so, how would I fix it? I have tried adding hdparm -B 254 /dev/sda to my /etc/rc.local file, but I still run into the clicking problem if my computer boots while plugged in and is then unplugged. Also, I'm finding this fix to be unreliable. Sometimes it works, sometimes it does not. Is this a good solution and is there a better way of doing this? Also, would running my laptop with a -B value of 254 have any negative effects? (I read somewhere about a lower level protecting the hard drive from bumps)

  Read the article

• windows 7 partition disappeared

  - by atoMerz

  I have a VPCF2 with windows 7 installed on it. I was working on my computer when on of my drives (D) disappeared. I can see it in Computer Management>Disk Management and it'd marked as Healthy(Primary Partition). When I right click on it the only options that are enabled are Delete Volume and Help. So I cannot assign a drive letter to it (not even in safe mode). I tried System Restore and it failed. I tried to boot the system using ubuntu tha was installed on my system but that fails too because it was installed on partition D. I'm hopeless. What can I do?

  Read the article

• How do I force the system to look for new sound devices?

  - by John Zeringue

  I have a small flat screen TV (Toshiba) that I often connect via HDMI to my laptop (an HP Pavilion dv4) and use as a computer monitor. When I do this, I prefer to use the TV's speakers, particularly when I'm watching video, because the sound quality is much better. However, when I connect the HDMI cable after turning on my computer (rather than having it plugged in before booting up), Sound Settings does not list the TV as an output device, and I am forced to reboot. I was curious if there is an easier solution to this, perhaps a CLI command to check for new sound outputs. Does anyone know of something like this or have another solution? To clarify, I believe this is a software problem. The HDMI always works, and I can switch my desktop over to the TV at any time. The issue is that, if the HDMI wasn't connected during start up, the TV will not appear as an output option in the Sound Settings GUI. So, unless I'm mistaken, my question is not HDMI specific, but rather a general usage question about manipulating sound settings from the command line.

  Read the article

• Using git with cgit for decentralized/centralized development

  - by polemon

  I plan to use git for hosting my projects on my server. I've read about cgit, git-daemon, and I more or less decided to use those tools. But general use is still kind of confusing for me. What do I need to set up on the server, to push my files onto it. And when the files on the server are newer as the files on my computer, how do I merge them? Also, I use, say, two computers where I develop. How do I merge from one computer to the other? Also, when two people are working on the same project, how do they merge their local repos from one another? As you probably can tell by now, I come from SVN, but I've worked with Mercurial and now I'd like to test git.

  Read the article

• How do I remove Lenovo Veriface from the login screen?

  - by Xenorose

  I have a Lenovo laptop which came preloaded with Windows 7. Every time I start the computer and get to the Windows log-in screen (where you enter the user password) I get a message about Veriface software giving me the option to use it. I'd like to disable this. I went over the Program's settings and there is nothing that allows you to disable it from loading with Windows. Also, I thought that it might be a service to disable, but I don't see it in the list of services, nor is it in the list of start-up Processes (either in msconfig or in the registry). I'm considering uninstalling it completely, but since it's a part of the lenovo software pack that came with the computer and I do use some of these software, I'm not sure if uninstalling it might also remove wanted things (and uninstalling and reinstalling if needed seems like a mess). Anybody know if there's an easy way to achieve this?

  Read the article

• WD: UDMA CRC Errors and Reallocated Sector

  - by Leo White

  I got a WD Caviar Black 1TB (WD1001FALS) and according to SMART, I got: one "Reallocated Sector" one "Reallocated Event" 26 UDMA CRC Errors in my drive but it's a "Pass" for the "SMART overall-health self assessment test". I think it's because of these, I'm having problems with Grub, and thus can't boot into any OS at all. Are these problems serious? According to "Warranty Services", my drive is still "In Limited Warranty". Would I be eligible for a replacement? FYI: I'm running Ubuntu 11.10. Any help will be appreciated. Thanks

  Read the article

• Hibernate doesn't work in Windows 7 64bit

  - by hey

  Hibernate doesn't work in Windows 7 64bit. When I try to hibernate, it just turns off computer and when I turn on it, it doesn't resume and it just starts as 'fresh' again. I updated my drivers. What is the problem? Can you give me a hand? Thank you. Come on, please help me, I really need hibernate working, 100 of my reputation will go to you. Thanks. Edit, by the way, my model is: Inspiron N5010. After I hibernate and turn on my computer, it just show Shut down didn't shut down correctly.

  Read the article

• Thunderbird: "Could not initialize the application's security component" [closed]

  - by user unknown

  In Thunderbird, on startup, I get the error message: "Could not initialize the application's security component" The message continues to check permissions of the profile, and free disk space. df -h shows, that I have 19G free disk space. find . -not -perm -644 -not -perm -600 -ls shows: No file without rw-permissions for me. Before the error occured, thunderbird worked well. But I changed my main mail-account. I had two, let's call them A and B, and used mainly A, but now I wanted to deaktivate it, and receive and send automatically via the second. I Had problems moving the filters from inbox A to inbox B (missing copy-functionality). In the web, I found (mollazine) hints, to move key3.db, cert8.db and secmode.db out of the way, but it didn't work for me. Another hint was to uninstall Quickcam(?. sic!), but I don't have Quickcam. A third to recreate the profile, but I have subdirectories, filters, addressbook, groups - mails back to the year 2003. I don't want to risk the loss of data. The whole errormessage is: Could not initialize the application's security component. The most likely cause is problems with files in your application's profile directory. Please check that this directory has no read/write restrictions and your hard disk is not full or close to full. It is recommended that you exit the application and fix the problem. If you continue to use this session, you might see incorrect application behaviour when accessing security features. When I open the error-console, it is empty.

  Read the article

• Extremely slow desktop and laggy. Need help with graphics driver

  - by user171624

  I am a fresh newbie Ubuntu user and I just installed my first Ubuntu 13.04 onto my HP Slate 2. I did a liveCD on my USB drive and installed everything perfectly fine...nice and smooth, not a trace of lag. Then I rebooted using Ubuntu itself on the computer, it was extremely slow and laggy. Icons or any buttons doesn't trigger right away, the performance of the entire thing looks like either 0.25 fps to 1 fps. My HP Slate 2 information: Processor: Intel Atom Z670 1.5Ghz Memory Ram: 2.0 GB Videocard: Intel GMA 600 (PowerVr SGX535) SolidStateDrive(SSD): 32GB I tried installing the intel linux graphics driver and it failed to install because it said I don't have any intel based graphics card. Well...I do as you see above. What can I do? I can't get on the internet on it, I'm using my primary computer (Windows 7) to do all the searchings and put the files onto the USB to move it over to my tablet. Simply...I don't get it...using liveCD on USB, it was all nice and smooth...then after the installation...BOOM! Slow, laggy, and etc. Can anyone help me? Thanks!

  Read the article

• Discrete Math and Computing Course

  - by ShrimpCrackers

  I was recently admitted into a Computing and Software Systems program (basically software engineering) and one of the first courses I'll be taking is called Mathematical Principles of Computing. The course description: "Integrating mathematical principles with detailed instruction in computer programming. Explores mathematical reasoning and discrete structures through object-oriented programming. Includes algorithm analysis, basic abstract data types, and data structures." I'm not a fan of math, but I've been doing well in all my math classes mostly A's and B's ever since I started two years ago, and I've been doing math every quarter - never took a quarter without math - so I've been doing it all in sequence without gaps. However, I'm worried about this class. I've read briefly on what discrete math is and from what my advisor told me, its connection with computer science is that it has alot to do with proving algorithms. One thing that my instructors briefly touched on and never went into detail was proving algorithms, and when I tried, I just wasn't very good at mathematical induction. It's one of the things that I ignored every time it showed up in a homework problem (usually in Calculus III which I'm finishing up right now). Questions: 1. What can I expect from this class? 2. How can I prepare myself for this class? 3. Other tips? Thank you.

  Read the article

• Which are the best ways to organize view hierarchies in GUI interfaces?

  - by none

  I'm currently trying to figure out the best techniques for organizing GUI view hierarchies, that is dividing a window into several panels which are in turn divided into other components. I've given a look to the Composite Design Pattern, but I don't know if I can find better alternatives, so I'd appreciate to know if using the Composite is a good idea, or it would be better looking for some other techniques. I'm currently developing in Java Swing, but I don't think that the framework or the language can have a great impact on this. Any help will be appreciated. ---------EDIT------------ I was currently developing a frame containing three labels, one button and a text field. At the button pressed, the content inside the text field would be searched, and the results written inside the three labels. One of my typical structure would be the following: MainWindow | Main panel | Panel with text field and labels. | Panel with search button Now, as the title explains, I was looking for a suitable way of organizing both the MainPanel and the other two panels. But here came problems, since I'm not sure whether organizing them like attributes or storing inside some data structure (i.e. LinkedList or something like this). Anyway, I don't really think that both my solution are really good, so I'm wondering if there are really better approaches for facing this kind of problems. Hope it helps

  Read the article

• How do I automatically download files to a Kindle 2 whenever its USB connection is plugged into a Windows 7 machine?

  - by Bob Cross

  The inspiration of this question is the Gadget Lab article How To Make Your Kindle Into an Automatic Instapaper. In that article, they describe an implementation of an Automator workflow that: Detects the connection of a portable disk (which the workflow assumes is the Kindle 2). Downloads the Instapaper mobi file containing the text version of the articles marked for "Read Later" to the computer. Downloads the mobi file from the computer to the Kindle 2. All of this is straightforward in terms of functionality but it is not immediately obvious how to do step 1 on a Windows box. Is the Task Scheduler the first step? If so, which event should be the trigger for the rest of the task?

  Read the article

• external usb hard drive is not being seen anymore

  - by incrediblehulk

  I think my problem is a little different than several other similar titled questions. Everything started while I was using 10.10. External drive was always recognized and mounted, but the timing of this differed. I mean when I booted, the OS sometimes saw the drive immediately, sometimes after a few minutes, sometimes after hours. Although this was annoying, I tolerated this somehow. Then this problem persisted after I upgraded to 11.04 with a clean install. Afterwards, the drive became totally invisible to the OS. It is not even detected as an usb device anymore. However, there is one thing I can do to make it seen. If I boot to another operating system which can detect the drive, and then boot back to ubuntu, everything is perfect. but this is of course very impractical. To summarize, the usb drive is recognized by ubuntu if and only if another OS in the same computer could recognize it first. I should also say I have not had any problems with the same drive in any other OS or a different computer. My drive is philips with a hitachi hdd inside, has its own power source and any other usb powered drives have never caused this kind of a problem. I've tried almost all recommendations in similar topics but none of them seems to be related to this one. What can I possibly do to fix this?

  Read the article

• games and movies become too slow after some time

  - by ishaq

  On my gaming desktop, I was fixing my desktop's power supply when something seemed to burn (I got that stinging burning smell). However when I turned ON the computer (it was OFF before), everything seemed to be fine. However, I have noticed that now it becomes too slow if I play a game or movie on it. I am talking about the computer becoming painfully slow after about 5 minutes into the movie/game (it works fine otherwise e.g. browsing), it becomes so slow I can see individual frames from movies/games. What could be the problem? A fried video card? friend memory (RAM), something else? My system's configuration is: Intel Core i7 CPU 3.40GHz 8GB DDR3 RAM 2TB WDC HDD NVIDIA GeForece GT 220 (1GB) Thermal Take Commander MS1 Chassis ( http://www.thermaltakeusa.com/Product.aspx?S=1394&ID=2051 ) mainboard: Intel DH67CL AAG10212-208 Realtek High Definition Audio

  Read the article

• How to add network printer remotely without knowing the IP?

  - by Steve

  Assume your friend from over 100km away asked you to add a network printer to his computer since you're so tech savvy. How would you add network printer remotely in this case? You would need: 0. Remote connection to your friend's computer 1. Printer IP and brand/model names 2. Respective drivers downloaded either from manufacturer's website or Windows Update driver Question is, how would you find out the IP address of the printer without bothering your friend too much with technical steps? Since your friend isn't as tech savvy as you - they wouldn't know which buttons to press to get IP address.

  Read the article

• Java Applets fail to launch in Windows 7 64bit

  - by Steve

  Hi can you help? I'm having great trouble launching Java applets using Windows 7 64 bit. I have the 32 bit version of Java installed (as recommended, for use with 32 bit browsers). When I click on an Java applet to open it the Java logo shows with a circular progress bar, but the process goes no further, just the progress bar going round and round. There are no error messages. The computer is a few months old and Java has never worked properly. I've tried with both IE9 and Chrome, followed the suggested fixes, uninstall then reinstall, check certain browser settings (all were in order), check Java control panel settings (again all was in order) delete the internet cache etc, tried 32bit & 64bit Java side by side. All to no avail. I'm baffled Is there anything else to try, or do I have to accept a computer without Java (Very inconvenient!) Thanks

  Read the article

• Is Reading the Spec Enough?

  - by jozefg

  This question is centered around Scheme but really could be applied to any LISP or programming language in general. Background So I recently picked up Scheme again having toyed with it once or twice before. In order to solidify my understanding of the language, I found the Revised^5 Report on the Algorithmic Language Scheme and have been reading through that along with my compiler/interpreter's (Chicken Scheme) listed extensions/implementations. Additionally, in order to see this applied I have been actively seeking out Scheme code in open source projects and such and tried to read and understand it. This has been sufficient so far for me understanding the syntax of Scheme and I've completed almost all of the Ninety-nine Scheme problems (see here) as well as a decent number of Project Euler problems. Question While so far this hasn't been an issue and my solutions closely match those provided, am I missing out on a great part of Scheme? Or to phrase my question more generally, does reading the specification of a language along with well written code in that language sufficient to learn from? Or are other resources, books, lectures, videos, blogs, etc necessary for the learning process as well.

  Read the article

• Is there a Google Authenticator desktop client?

  - by cwd

  I am using Google Authenticator for 2-step authentication. I like how I can use a code and verify my account using my phone: I realize that the app was designed to run on a device other than a computer to increase security for the computer (in case that it is lost or stolen), but I would like to know if there is a way I can run Google Authenticator on my Macbook. Now, per the Google Authenticator Page it will not run on a desktop: What devices does Google Authenticator work on? Android version 2.1 or later BlackBerry OS 4.5 - 6.0 iPhone iOS 3.1.3 or later However there are several emulators for developers and so I wonder if it is possible to run one of these emulators and then run Google Authenticator with that. I do realize this is not a best practice - but I'm less worried about my laptop getting stolen and more worried about someone just hacking the account. So my question is this: Is it possible to run it on the desktop, even though it is not meant to be / not recommended?

  Read the article

• Windows 7 - all usb devices go to sleep im idle mode

  - by dvdx

  A strange thing happened after a few updates to the system: Intel rapid storage SSD firmware update Intel Ethernet adapter update GPU Intel update When the computer turns off the screen (after 5 min), an unknown time later, all the USB devices stop working. Sound card Mouse Keybord etc. I can't turn them back on, so I can't wake up the screen or do anything except turn the computer off and back on. I checked my power save profile and all is OK there. I changed in the Device Manager, the Allow USB to sleep in all the hubs. How can I fix this??

  Read the article

• Hard disk failure. Can I recover my "move"d folders?

  - by Doug

  I am in the process of moving all my files from an old laptop to new one. I just moved 11gb of data from my old laptop to a hard drive (external) and then upon moving it out to the new hard drive, the hard drive is getting a CRC (Data Error (Cyclic Redundancy Check). Now I am looking for a solution to recover the files that I moved on my old laptop (not the external). I understand they they are just marked for potential overwriting to free up space. I was getting ready to test out GetDataBack, but it says to install it on a healthy windows and use the recover-needed drive as an external. However, I don't want to turn off my computer without first getting the okay since it is in a "moved" state. Please help! What can I do to recover the Moved files. I haven't touched the computer since it has been moved. What can I use to recover them?

  Read the article

• pscp: how to copy a file from a windows machine to a non-home location on another windows machine?

  - by help

  I want to copy a file from C:\temp on MachineA to C:\final on MachineB. I tried to use the following command, but it gave me an error (permission denied): C:\PROGRA~1\putty\pscp.exe -i C:\PROGRA~1\cwRsync\home\rcadmin\.ssh\id_rsa_private.ppk [email protected]:C:\final\test.txt C:\temp\test.txt It turned out I can only access C:\users\direcpc in my source computer. So if I put the file in C:\users\direcpc\text.txt, then it would work: C:\PROGRA~1\putty\pscp.exe -i C:\PROGRA~1\cwRsync\home\rcadmin\.ssh\id_rsa_private.ppk [email protected]:/test.txt C:\temp\test.txt But I want to access any location on my source computer instead of just my user home directory, is there a way to do this?

  Read the article

• How can I solve Windows PPTP VPN issues?

  - by Robin M

  I'm having persistent problems with Windows PPTP VPN connections. The VPN appears up whilst the tunnel won't transfer traffic (ping to a remote IP within the VPN works for a while, and then fails). The client receives routing information via DHCP. When the connection fails, the routing table is still correct so I don't think it's a routing problem. My internet connection is via an ADSL2 line. There's software to deal with PPTP problems, like TunnelRat, but I don't want to install v1.1 of the .NET framework and I'd rather get to the bottom of the problem (I have multiple VPN connections and some are more unreliable than others). What can I do to get to the bottom of this? Alternatively, what can I do to keep the connection alive?

  Read the article

• Certificates compartments (certmgr.msc)?

  - by Royi Namir

  After reading a while , Im trying to understand what kind of certificates will be found at : Personal Other People Trusted Root Certicfiation Authorities will personal will contains only private keys ? I'm a bit confused. What about certificates which arent trusted and I manually trust them , where will they be ? Also , Why do I only have the CurrentUser Tab in my computer ? where is the local computer tab ? here is a picture from the internet. I only have the "current user" Node.... Thanks.

  Read the article

• Yum install error (mysql-devel) depsolve

  - by Pasta

  I get the following error on yum install mysql-devel. Can anyone help? I dont have this in my /etc/yum.conf exclude list. --> Finished Dependency Resolution mysql-server-5.0.45-7.el5.x86_64 from installed has depsolving problems --> Missing Dependency: mysql = 5.0.45-7.el5 is needed by package mysql-server-5.0.45-7.el5.x86_64 (installed) Error: Missing Dependency: mysql = 5.0.45-7.el5 is needed by package mysql-server-5.0.45-7.el5.x86_64 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest Please help!

  Read the article

• Does the size of the monitor Matter?

  - by Arsheep

  I have a old computer, and I want to buy a big LCD. The best I've found so far is Viewsonic's 24" LCD TFT monitor. So will it run without any problems, or do I need to upgrade the video cards or something as well? The computer is not too old: it has P4 board and celeron processor, with 128 graphics memory. And in display properties, it says that the maxium that I can use is 1280 x 1024 resolution. I am noob hardware-wise, so need help on this stuff. Thanks

  Read the article

< Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >