Search Results

Search found 2488 results on 100 pages for 'virtualization portfolio'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 32/100 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

  • Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

    - by jamieb
    I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

    Read the article

  • Windows 7 x64 Boot Camp Partition, Snow Leopard on MBP, and VMWare Fusion 2.x/3 - Endless Repair Sta

    - by Keith Fitzgerald
    Thanks in advance for your help! As the title states, I have Windows 7 x64 Boot Camp Partition, Snow Leopard on MBP, and VMWare Fusion 2.x/3.x. I'm trying to open the partition as a vm and I get into an endless cycle where windows tries to Repair Start Up disk for a very long time before failing. The boot camp partition runs fine natively. Has anyone experienced this? Can someone provide or link a remedy? My google fu is failing miserably ....

    Read the article

  • Tool that will virtualize BIOS

    - by Nrew
    Is there any application that can virtualize the BIOS?So that you can see the effects of what the changes in the setting of your BIOS. I know that there are many versions of BIOS depending on your hardware. But is it possible to copy it and then virtualize it when you are running your system. So that you can see if your system can still run after changing the settings.

    Read the article

  • How to subnet hosted VMs

    - by bwizzy
    I have a network of VMs each having a LAN IP address and a public IP address. They each have a 1:1 NAT map for public access via the public IP for HTTP, SSH etc. I'm trying to figure out a way to restrict the LAN IPs from talking to each other, but there are some cases where a group of LAN IPs will need to communicate. I'm using pfSense as a firewall / router on a 192.168.0.0/24 configuration. It seems like I could assign each VM it's own subnet and add a static route to the firewall for that VM to get back to the firewall for internet access / other fw rules. Is that right? I assigned 1 VM with: address 192.168.1.2 netmask 255.255.255.254 gateway 192.168.1.1 Then added a static route on the FW's LAN interface using 192.168.1.0/30 as the destination network and 192.168.1.1 as the gateway. Nothing appears to be working, anyone have any ideas? Please be aware I'm not that familiar with subnets. Thanks!

    Read the article

  • Bridging VirtualBox over OpenVPN TAP adapter on Windows

    - by Sean Edwards
    I'm trying to configure a virtual machine (VirtualBox guest running Backtrack 4) with a bridged adapter over a VPN connection. The VPN is is hosted by the cybersecurity club at my university, and connects to a sandboxed LAN designed for penetration testing against various servers that the club has built. My host (Windows 7 Ultimate) connects to the VPN fine and is assigned an IP through DHCP, but for some reason the VM can't do the same thing, and I'm not sure why. It's like OpenVPN is filtering out packets from the MAC address it doesn't recognize. I want the virtual machine to bridge over the VPN connection, because our IT office has very strict policies about what you can and can't do on the network. I want to be able to run active attacks (ARP spoofing, nmap, Nessus scans) in the sandbox environment without risking the traffic accidentally going over the university network and getting my internet access revoked. Bridging over the VPN connection and running all attacks from inside the VM would solve that problem. Any idea why the host can use this interface, but the VM can't?

    Read the article

  • Xen on bare metal, Mac OS X 10.6, Vista, Debian as guest OSes

    - by Mischa Arefiev
    I have: a desktop PC (Athlon 64, 2 cores) ...that came with Windows Vista, and a retail DVD of Mac OS X 10.6 I want: to install Mac OS X through Hackintosh (I believe my hardware is suitable), to also run Windows Vista with full 3D support for video games and Youtube, to also run Debian GNU/Linux with optional 3D for work. I don't think my CPU supports VT-x, but it should have AMD-V. So the question is: Can all of this be done with Xen (Xen on bare metal, all three OSes as guests)? Or should I just try to install OS X first and then run Vista and Debian in Parallels?

    Read the article

  • windows server 2008 instance on KVM stuck in 'Pause' mode

    - by mdoust
    I have a windows Server 2008 instance as a guest on KVM. When I tried to run it via virtual machine manager, the process got frozen after few seconds and trying to resume the process lead to this error from virt-manager: Error unpausing domain: internal error unable to execute QEMU command 'cont': Resetting the Virtual Machine is required I tried to Reboot it without any success. Any help will be highly appreciated.

    Read the article

  • Windows 2008 running as KVM guest networking issue

    - by Evolver
    I have a strange networking problem with Windows 2008 server R2, running as guest under KVM-Qemu host. Host is CentOS 6.3 x86_64. It's network settings: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 BOOTPROTO=static BROADCAST=xx.xx.xx.63 IPADDR=xx.xx.xx.4 NETMASK=255.255.255.192 NETWORK=xx.xx.xx.0 ONBOOT=yes TYPE=Bridge # cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=xx:xx:xx:xx:xx:xx ONBOOT=yes BRIDGE=br0 IPV6INIT=yes IPV6_AUTOCONF=yes # cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=my.hostname GATEWAY=xx.xx.xx.1 # cat /etc/sysctl net.ipv4.ip_forward = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.rp_filter = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.accept_source_route = 0 # tried to set it to 1 without any changes kernel.sysrq = 0 kernel.core_uses_pid = 1 net.ipv4.tcp_syncookies = 1 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 kernel.msgmnb = 65536 kernel.msgmax = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1004 0 0 br0 0.0.0.0 xx.xx.xx.1 0.0.0.0 UG 0 0 0 br0 Node IP is xx.xx.xx.4, guest IP is xx.xx.xx.24, both host and guest is in the same network (/26). There are several linux guest running fine on the node (centos, debian, ubuntu, arch), and even Windows 2003 x86 also running fine. But Win2008 does not. I wonder, what's the difference. From Win2008 guest I can ping nothing: neither gateway, nor any other IP, even they are in the same subnet. From outside I also cannot ping guest. Almost. If I ping it from another server in same subnet, it's barely pinging, losing more than 90% packets. Firewall on the guest is completely off. Tried to set up network manually as well as via DHCP without success (BTW, DHCP set up network settings correctly). I suspect that is a kind of routing problem, but I spent whole day and still cannot figure it out. I would be appreciate for any help.

    Read the article

  • tap interfaces always disabled in linux bridge

    - by Dani Camps
    I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

    Read the article

  • Find out ESXi host from VM? [duplicate]

    - by Kyle Brandt
    This question already has an answer here: Determining the name of the VMware host of a VM guest - from the guest 3 answers I have a monitor that is running on all guests, Windows and Linux. I'd like to send back the Parent host of the guest with this monitor, How can I found out the VM host from within a ESXi VM? Ideally I'm looking for a universal way to do this from both Windows and Linux, but if they are separate paths that okay. Using something from VMWare tools would be fine, but I'm not currently using anything running the vSphere API.

    Read the article

  • Access localhost on Mac OS X from Parallels machine

    - by AntonAL
    Hi, i need to test my web site, running on a local Mac, under several browsers in Windows. I use Windows XP, installed in Parallels Desktop. It would be great, when i will be able to access my http://localhost:3000 from Windows, sitting in virtual environment (Parallels). How to wire all the stuff up ?

    Read the article

  • Windows 7 XP Mode, Resizing triggering lock

    - by greggorob64
    I'm a developer using Windows 7 XP Mode to get some old 16-bit apps to run. A hugely annoying hurtle I'm encountering is this: When I resize my XP windows at all (usually by mistake), it automatically logs me off (or Locks), requiring me to log in. This causes my build batch file to stop, which is potentially hours of work lost. Any help would be appreciated, thanks.

    Read the article

  • Difference between VMWare tools?

    - by tore-
    I'm currently writing a module for puppet which installs VMWare tools to virtual nodes. I want to do this via yum and and yum-repo. VMWare have their own repo (http://packages.vmware.com/tools/esx/3.5latest/rhel5/x86_64/index.html) which I thought I could use, rather than creating my own. But then I noticed that their repo files is alot different than the rpm file used when installing VMWare Tools on the node, via the "Install/upgrade VMWare Tools" in vSphere. Does anyone know what the real difference is? Does anyone have any preferences?

    Read the article

  • Broken filesystem on Windows XP / 7 virtual machine

    - by Pekka
    I created a virtual machine with Windows XP as the guest system in Microsoft's Virtual PC that ships along with Windows 7. I then installed Virtualbox and began running the MS machine in it. It worked fine. Then, I accidentally started the machine in Microsoft's Virtual PC again. The screen stayed blank, so after a while, realizing my mistake, I closed the Machine. Since then, the VM won't start any more, claiming massive file system problems. Starting Windows in normal mode results in a SOMETHING_FILESYSTEM blue screen; I can start in protected mode and run a checkdisk. That will fix something on every run, but every time I restart, it will start again. I tried re-booting the VM with the Windows CD and doing a repair install. I didn't watch whether that worked out, but I'm caught in the reset / check disk / reset cycle again. Is there anything VM specific that can still be done? On a physical machine, I would say reformat. Is there any way to get hold of the data on the virtual machine through either Virtual PC or Virtualbox? It was an experimental machine, but I had started entering some data on it that would be nice to recover.

    Read the article

  • IP Forwarding and Routing in Windows 2008

    - by Danialzo
    I have Hyper-V running on a windows 2008. I got a new ip stack from the data center to be set on my virtual machines. But I have difficulties to set these IPs on my VMs because they are on different network. my current server ip is xxx.xxx.18.6 with MASK : 255.255.255.224 and the GW is xxx.xxx.18.1 my new ip stack is xxx.xxx.168.176/29 I can use RRAS to achieve this. Do I need to create another NIC? How do I make these VMs reachable from outside?

    Read the article

  • Cannot change PostgreSQL port

    - by Jerec TheSith
    I run Postgresql 8.4 as a service on a CentOS 6.2 server. I set port = 21444 and listen_addresses = '*' in /var/lib/pgsql/data/postgresql.conf and I changed 5432 to 21444 in postmaster.opts and restarted postgres, but when I run netstat -lntp postgresql is still running on port 5432 tcp 0 0 0.0.0.0:5432 0.0.0.0:* LISTEN 20276/postmaster When I restart postgresql I get a writting error warning on /proc/self/oom_adj, but the service starts anyway. I read that we could get this error when using virtualized servers, but I don't really know if this has inpact on postgresql listening port. The correct pgsql config file is loaded in /var/lib/pgsql/data : [root@srv02 ~]# ps -ef | grep postgres root 1358 22140 0 09:42 pts/0 00:00:00 grep postgres postgres 9519 1 0 Mar16 ? 00:00:01 /usr/bin/postmaster -p 5432 -D /var/lib/pgsql/data postgres 9573 9519 0 Mar16 ? 00:00:00 postgres: logger process postgres 9575 9519 0 Mar16 ? 00:00:05 postgres: writer process postgres 9576 9519 0 Mar16 ? 00:00:03 postgres: wal writer process postgres 9577 9519 0 Mar16 ? 00:00:01 postgres: autovacuum launcher process postgres 9578 9519 0 Mar16 ? 00:00:01 postgres: stats collector process any thought ? thanks, Jerec

    Read the article

  • URL redirect to a virtual server on a VLAN

    - by zeroFiG
    I have a production site, running off 10 servers. I've been given another virtual server on the same network as these 10 servers, to use for testing purposes. This server doesn't have it's own DNS entry. Therefore I need to do a redirect to the site hosted on this virtual server for a sub-domain of the site running on the 10 other servers. So Basically I was wondering how I would configure a sub domain of my production server to point at the Virtual server for testing. I'm guessing I need to modify my site file in /etc/apache2/sites-available and add another virtual host like the following and modify the redirect match: <VirtualHost *> ServerName SUBDOMAIN.DOMAIN.com RedirectMatch 301 (.*) **IP ADDRESS** CustomLog /var/log/apache2/SUBDOMAIN.DOMAIN.com.access.log combined </VirtualHost> Do I set the redirect match to just the IP on the Virtual server, and then configure another site file in the sites-available directory, which will recption this redirect and point the browser towards the HTML root? Thanks, I hope I made myself clear.

    Read the article

  • When I restart my LXC environment, the container does not re-bind to the IP address

    - by RoboTamer
    The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

    Read the article

  • Can KVM CPU assignment count differ from physical hosts CPU count?

    - by javano
    I have read this question. I knew already that I could for example, have a quad core machine with four guests each having two vCPUs. As they don't all be require 100% CPU usage all the time, the scheduler would handle this for me. My question is about how this relates to a fail-over or migration situation; If host1 has two dual-core CPUs, and I assign guest1 four vCPUs (so it accessed all four physical cores), what will happen if I try and migrate it to host2 which only has one dual-core CPU? Can qemu-kvm emulate more vCPUs than there are physical? Or would I have to shut down the virtual machine, change the CPU assignment, migrate it, and then boot it back up (so no live migration)? Many thanks.

    Read the article

  • SSH Public Key Authentication only works if active session exists before

    - by Webx10
    I have a rather strange problem with my SSH configuration. I set up my server with the help of a Remote Access Card and configured everything with a KVM viewer. So while being logged into the server via the KVM Viewer I configured SSH with only pubkey and tried to login from my local laptop. It worked fine. If I quit the KVM Session (or logout with the user in the KVM session) I cannot login via ssh anymore (pubkey denied). SSH login only works as long as the user is somewhere still logged in. Any hints what the problem might be? Console output for a failed login (all personal data exchanged): OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /Users/mylocaluser/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 103: Applying options for * debug1: Connecting to 100.100.100.100 [100.100.100.100] port 12345. debug1: Connection established. debug1: identity file /Users/mylocaluser/.ssh/id_rsa type 1 debug1: identity file /Users/mylocaluser/.ssh/id_rsa-cert type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 debug1: match: OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ab:12:23:34:45:56:67:78:89:90:12:23:34:45:56:67 debug1: Host '[100.100.100.100]:12345' is known and matches the RSA host key. debug1: Found key in /Users/mylocaluser/.ssh/known_hosts:36 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa2 debug1: Authentications that can continue: publickey debug1: Trying private key: /Users/mylocaluser/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). Console output for a successfull login (only possible while "active session" exists): OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /Users/mylocaluser/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 103: Applying options for * debug1: Connecting to 100.100.100.100 [100.100.100.100] port 12345. debug1: Connection established. debug1: identity file /Users/mylocaluser/.ssh/id_rsa type 1 debug1: identity file /Users/mylocaluser/.ssh/id_rsa-cert type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 debug1: match: OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ab:12:23:34:45:56:67:78:89:90:12:23:34:45:56:67 debug1: Host '[100.100.100.100]:12345' is known and matches the RSA host key. debug1: Found key in /Users/mylocaluser/.ssh/known_hosts:36 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 279 debug1: Authentication succeeded (publickey). Authenticated to 100.100.100.100 ([100.100.100.100]:12345). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = de_DE.UTF-8 Welcome to Ubuntu 14.04.1 LTS

    Read the article

  • What are the most important aspects to consider when choosing a SAN for a small office virtualizatio

    - by Prof. Moriarty
    I am in the process of consolidating 6 physical servers running 6 different operating system flavors (don't ask) into two identical physical servers (Dell PowerEdge 2900), using the free VMware ESXi 4.0 platform. We will install an iSCSI SAN over a 1GbE network, and store all virtual machine images on the SAN. Each physical server would run 3 VMs, and in the case of a physical server failure, we would manually switch over the other 3. These are all internal servers, while important, they can tolerate some amount of downtime (say <1h) to keep cost and complexity associated with HA down. I now need to choose the SAN to be used for the setup, on a low budget. We currently have about 2TB of data, but of course I want to able to grow, do backups of VM snapshots on other drives and remove them to a different location, etc. So what I would like to know is: Which are the must have features for this setup, without which using a SAN is not worth it? We are mostly a Dell shop, so I have been looking at the EqualLogic PS4000E High Availability model. Any opinions, anecdotes, bad experiences with this model? (This is one of the few models which could accomodate our existing disks from the physical servers.) If you can recommend something that is not Dell, but it has better value, I would most definitely consider it. Caveats, things to look out for?

    Read the article

  • How to distinguish between virtual disk image formats?

    - by Jakub Žitný
    There is huge number of different formats for virtual storage files for desktop and server purposes (vmdk, qcow2, vdi, vdk, etc.). I'm writing a little script for manipulating them and would like the script to be able to distinguish between them. Of course, it can be done via extension, but I want this to be more reliable. I tried commands file or qemu-img, but the results are not quite clear. Any idea improving my methods?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >