Search Results

Search found 21005 results on 841 pages for 'disk format'.

Page 321/841 | < Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Reusing slot numbers in Linux software RAID arrays

  - by thkala

  When a hard disk drive in one of my Linux machines failed, I took the opportunity to migrate from RAID5 to a 6-disk software RAID6 array. At the time of the migration I did not have all 6 drives - more specifically the fourth and fifth (slots 3 and 4) drives were already in use in the originating array, so I created the RAID6 array with a couple of missing devices. I now need to add those drives in those empty slots. Using mdadm --add does result in a proper RAID6 configuration, with one glitch - the new drives are placed in new slots, which results in this /proc/mdstat snippet: ... md0 : active raid6 sde1[7] sdd1[6] sda1[0] sdf1[5] sdc1[2] sdb1[1] 25185536 blocks super 1.0 level 6, 64k chunk, algorithm 2 [6/6] [UUUUUU] ... mdadm -E verifies that the actual slot numbers in the device superblocks are correct, yet the numbers shown in /proc/mdstat are still weird. I would like to fix this glitch, both to satisfy my inner perfectionist and to avoid any potential sources of future confusion in a crisis. Is there a way to specify which slot a new device should occupy in a RAID array? UPDATE: I have verified that the slot number persists in the component device superblock. For the version 1.0 superblocks that I am using that would be the dev_number field as defined in include/linux/raid/md_p.h of the Linux kernel source. I am now considering direct modification of said field to change the slot number - I don't suppose there is some standard way to manipulate the RAID superblock?

  Read the article

• Fixing a corrupted Windows Server 2003 server

  - by Keith

  I have a Windows Server 2003 server that is being mainly used for some reporting done in SQL Server. Recently Windows has started complaining about being corrupted, we are getting an NTFS error 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume1. The server is RAID 5 and I did have a disk die however the RAID never went degraded since I have a hotspare. I replaced the hot spare and I'm still having problems. When I run chkdsk I get tons of messages.. some are: Deleting corrupted attribute record (128, "") from file record segment 194746 Those go on for a while. Then it deletes some orphan files. Then it does Correcting error in index $I30 for file 132426 And that goes on for a while. Then I get tons of Recovering orphaned file RE1AB6~1.LOG into directory file 534959 I have seen a lot of errors relating to the SQL Server reporting services. What are my options at this point? I would prefer to fix the issue instead of building a new server but I don't know if I can at this point.

  Read the article

• Extracting information from active directory

  - by Nop at NaDa

  I work in the IT support department of a branch of a huge company. I have to take care of a database with all the users, computers, etc. I'm trying to find a way to automatically update the database as much as possible, but the IT infrastructure guys doesn't give me enough privileges to use Active Directory in order to dump the users, nor they have the time to give me the information that I need. Some days ago I found Active Directory explorer from Sysinternals that allows me to browse through Active Directory, and I found all the information that I need there (username, real name, date when it was created, privileges, company, etc.). Unfortunately I'm unable to export the data to a human readable format. I'm just able to take a snapshot of the whole database in a machine-readable format. Doing the snapshot takes hours and I'm afraid that the infrastructure guys won't like me doing entire snapshots on a regular basis. Do you know of any tool (command-line is preferable) that would allow me to retrieve the values of the keys or export it to XML, CSV, etc?

  Read the article

• Dual Boot Installing Ubuntu 12.04 with Windows 7 (64) on a non UEFI system fails

  - by Randnum

  I cannot seem to install the correct boot loader for a non-UEFI firmware system. I'm trying to install Ubuntu 12.04 and Windows 7 (64) which are technically compatible with GPT but for windows only if the firmware is UEFI enabled. My system uses the old BIOS system and does not support UEFI. Therefore, whenever I finish my Ubuntu install and try to install Windows I get a "cannot install to GPT partition type" error. Even if I use Gparted to format a special NTFS file format for windows it can't handle the GPT partition style because it doesn't have UEFI. But my ubuntu install always forces GPT during installation and never asks if I want to install the old BIOS style MBR instead. How do I resolve this? Both OS's will install fine on their own the problem is when I try to install the second OS it doesn't recognize any of the other's partitions and tries to rewrite it's own on top of the other. I've tried both OS's first and always run into the same problem. Since there is no way to make Windows recognize GPT without upgrading my Motherboard how do I tell Ubuntu to use the old BIOS MBR on install? Do I have to download a special Ubuntu with a specific grub version? or should I manaually configure my partition somehow to force it not to use GPT? Thank you,

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• NGINX returning 404 error on a valid url

  - by Harrison

  We have a site that runs PHP-FPM and NGINX. The application sends invitations to site members that are keyed with 40 character random strings (alphanumerics only -- example below). Today for the first time we ran into an issue with this approach. The following url: http://oursite.com/notices/response/approve/1960/OzH0pedV3rJhefFlMezDuoOQSomlUVdhJUliAhjS is returning a 404 error. This url format has been working for 6 months now without an issue, and other urls following this exact format continue to resolve properly. We have a very basic config with a simple redirect to a front controller, and everything else has been running fine for a while now. Also, if we change the last character from an "S" to anything other than a lower-case "s", no 404 error and the site handles the request properly, so I'm wondering if there's some security module that might see something wrong with this specific string... Not sure if that makes any sense. We are not sure where to look to find out what specifically is causing the issue, so any direction would be greatly appreciated. Thanks! Update: Adding a slash to the end of the url allowed it to be handled properly... Would still like to get to the bottom of the issue though. Solved: The problem was caused by part of my configuration... Realized I should have posted, but was headed out of town and didn't have a chance. Any url that ended in say "css" or "js" and not necessarily preceded by a dot (so, for example, http://site.com/response/somerandomestringcss ) was interpreted as a request for a file and the request was not routed through the front controller. The problem was my regex for disabling logging and setting expiration headers on jpgs, gifs, icos, etc. I replaced this: location ~* ^.+(jpg|jpeg|gif|css|png|js|ico)$ { with this: location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { And now urls ending in css, js, png, etc, are properly routed through the front controller. Hopefully that helps someone else out.

  Read the article

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• Safe use of Update-FormatData?

  - by Steve B

  In a custom PowerShell module, I have at the top of my module definition this code: Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") This is working fine as all .ps1xml files are loaded. However, the module is sometimes loaded using Import-Module MyModule -Force (actually, this is in the install script of the module). In this case, the call to Update-FormatData fails with this error : Update-FormatData : There were errors in loading the format data file: Microsoft.PowerShell, c:\pathto\myfile.Types.ext.ps1xml : File skipped because it was already present from "Microsoft.PowerShell". At line:1 char:18 + Update-FormatData <<<< -AppendPath "c:\pathto\myfile.Types.ext.ps1xml" + CategoryInfo : InvalidOperation: (:) [Update-FormatData], RuntimeException + FullyQualifiedErrorId : FormatXmlUpateException,Microsoft.PowerShell.Commands.UpdateFormatDataCommand Is there a way to safely call this command? I know I can call Update-FormatData with no parameters, and it will update any known .ps1xml file, but this would work only if the file has already been loaded. Can I list somewhere the loaded format data files? Here is a bit of background: I'm building a custom module that is installed using a script. The install script looks like : [CmdletBinding(SupportsShouldProcess=$true,ConfirmImpact="High")] param() process { $target = Join-Path $PSHOME "Modules\MyModule" if ($pscmdlet.ShouldProcess("$target","Deploying MyModule module")) { if(!(Test-Path $target)) { new-Item -ItemType Directory -Path $target | Out-Null } get-ChildItem -Path (Split-Path ((Get-Variable MyInvocation -Scope 0).Value).MyCommand.Path) | copy-Item -Destination $target -Force Write-Host -ForegroundColorWhite @" The module has been installed. You can import it using : Import-Module MyModule Or you can add it in your profile ($profile) "@ Write-Warning "To refresh any open PowerShell session, you should run ""Import-Module MyModule -Force"" to reload the module" Import-Module MyModule -Force Write-Warning "This session has been refreshed." } } MyModule defines, as first statement, this line : Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") As I updated my $profile to always load this module, the Update-Path command has been called when I run the install script. In the install script, I force import the module, which be fire again the module, and then, the Update-Path call

  Read the article

• 150 TB and growing, but how to grow?

  - by seandavi

  My group currently has two largish storage servers, both NAS running debian linux. The first is an all-in-one 24-disk (SATA) server that is several years old. We have two hardware RAIDS set up on it with LVM over those. The second server is 64 disks divided over 4 enclosures, each a hardware RAID 6, connected via external SAS. We use XFS with LVM over that to create 100TB useable storage. All of this works pretty well, but we are outgrowing these systems. Having build two such servers and still growing, we want to build something that allows us more flexibility in terms of future growth, backup options, that behaves better under disk failure (checking the larger filesystem can take a day or more), and can stand up in a heavily concurrent environment (think small computer cluster). We do not have system administration support, so we administer all of this ourselves (we are a genomics lab). So, what we seek is a relatively low-cost, acceptable performance storage solution that will allow future growth and flexible configuration (think ZFS with different pools having different operating characteristics). We are probably outside the realm of a single NAS. We have been thinking about a combination of ZFS (on openindiana, for example) or btrfs per server with glusterfs running on top of that if we do it ourselves. What we are weighing that against is simply biting the bullet and investing in Isilon or 3Par storage solutions. Any suggestions or experiences are appreciated.

  Read the article

• Configuring nginx to check for hard files in only a few directories,

  - by Evan Carroll

  For a node.js project I'm doing, I have a tree like this. +-- public ¦   +-- components ¦   +-- css ¦   +-- img +-- routes +-- views Essentially, I have the root to be set to public. I want all requests destined to /components/ /css/ /img/ To check to see if their appropriate destinations exist on disk. However, I don't want requests to other directories to even run an IO operation, /foo/asdf /bar /baz/index.html None of those should result in the disk being touched. I have a stansa that does the proxy to node.js, location @proxy { internal; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-NginX-Proxy true; proxy_pass http://localhost:3030; proxy_redirect off; } I just would like to know how to arrange this. My problem would be easily solved if try_files took a single argument, but it always wants a file first. location /components/ { try_files $uri, @proxy } location /css/ { try_files $uri, @proxy } location /img/ { try_files $uri, @proxy } However, there is nothing that I can find that will give me, location / { try_files @proxy } How do I get the effect I want?

  Read the article

• Use old raid drive as boot device without data loss

  - by Gabriel

  There were two disks in sw-raid. There were /dev/md1 as swap, /dev/md2 as boot and a /dev/md3 with ext4. The sw-raid was disabled by stopping and removing mdadm and then zeroing the superblock on each /dev/mdX partition with: sudo mdadm --zero-superblock /dev/sda1 sudo mdadm --zero-superblock /dev/sda2 sudo mdadm --zero-superblock /dev/sda3 In the disk that is the first boot device, I don't know if it's relevant, the system type of each partition was set back from fd to 82 or 83 with fdisk, /etc/fstab was updated, changing /dev/mdX to /dev/sdaX, and grub was reinstalled on the boot partition (/dev/sda2) with grub-instal. But the system wont boot. What else should I do to use this disk as the boot device without reinstall or data loss? Current output of fdisk Device Boot Start End Blocks Id System /dev/sda1 2048 33556480 16777216+ 82 Linux swap / Solaris /dev/sda2 * 33558528 34607104 524288+ 83 Linux /dev/sda3 34609152 3907027120 1936208984+ 83 Linux With it doesn't boot I mean that it stops in the grub console (with the grub> symbol). A ls command says: (hd0) (hd0,msdos3) (hd0,msdos2) (hd0,msdos1) (hd1) (hd1,msdos1) It's weird because hd1 was formatted with ext4...

  Read the article

• The BitLocker encrypted logical drive of my laptop is not accessible. On clicking error appears,"Application not found"

  - by Nauman Khan

  I had an important personal data that was stored in my laptop drive 'F'. My 4 year old son also uses my laptop to play games. To secure my data I used bitlocker software that was already there in my windows 7 ultimate 32 bit. I am using a Dell D 630 Core2Duo laptop. The thing worked fine for me and I have been able to access my data in drive 'F' as and when I required. But today, when I tried to open my 'F' drive, an error box appeared saying "Application not found". I right clicked and checked 'properties' of 'F' drive. It showed me Used Space = 0 bytes and Free Space = 0 bytes. I opened 'Disk Management' which showed my 'F' drive file system as 'Unknown (Bitlocker Encrypted). 'Disk Management' is also showing my 'F' drive as healthy logical drive. I opened 'Manage bitlocker' and found that my 'F' drive was being shown locked and 'Unlock Drive' was displayed against it, however, when i click on 'Unlock Drive', it does not function. I opened 'TPM Administration' and found an information that 'Compatible TPM cannot be found'. My bitlocker encryption was working fine which means that I had a compatible TPM in my laptop. Where has it gone? How can I enable it? Is my 'F' Drive lost forever and thus the data in there as well?

  Read the article

• Compatibility of Fedora install on a Hybrid drive

  - by kjh

  I recently bought un ultrabook with a 500gb/32gb sdd hdd hybrid drive, and I'm having trouble replacing windows on it with fedora seventeen. it errors out saying there was an unhandled exception. Is linux compatible with hybrid drives? or can the operating system on a hybrid drive not be replaced? Edit: here are the steps I select special storage devices because it ignores my hard drives otherwise at this point i get the message: "Disk contains bios raid meta data, disk sda will be ignored" I can pick a hostname, select my timezone and set a password at the install type screen, no matter what I select (use all free space, replace linux systems, create custom partition etc..) once I click next, it says "an unhandled exception" has occured. and I can no longer proceed with installation. Here is the error message: anaconda 17.29 exception report Traceback (most recent call first); File "/usr/lib64/python2.7/size-packages/pyanaconda/bootloader.py"; line 183 self.stage1_drive=self_drives[0] File "/usr/lib64/python2.7/site-packages/pyanaconda/rw/cleardisks_gui.ph"; line... and tons of more lines like that

  Read the article

• How to show what will be updated next pull?

  - by ???

  In SVN, doing svn update will show a list of full paths with a status prefix: $ svn update M foo/bar U another/bar Revision 123 I need to get this update list to do some post-process work. After I have transferred the SVN repository to Git, I can't find a way to get the update list: $ git pull Updating 9607ca4..61584c3 Fast-forward .gitignore | 1 + uni/.gitignore | 1 + uni/package/cooldeb/.gitignore | 1 + uni/package/cooldeb/Makefile.am | 2 +- uni/package/cooldeb/VERSION.av | 10 +- uni/package/cooldeb/cideb | 10 +- uni/package/cooldeb/cooldeb.sh | 2 +- uni/package/cooldeb/newdeb | 53 +++- ...update-and-deb-redist => update-and-deb-redist} | 5 +- uni/utils/2tree/{list2tree => 2tree} | 12 +- uni/utils/2tree/ChangeLog | 4 +- uni/utils/2tree/Makefile.am | 2 +- I can translate the Git pull status list to SVN's format: M .gitignore M uni/.gitignore M uni/package/cooldeb/.gitignore M uni/package/cooldeb/Makefile.am M uni/package/cooldeb/VERSION.av M uni/package/cooldeb/cideb M uni/package/cooldeb/cooldeb.sh M uni/package/cooldeb/newdeb M ...update-and-deb-redist => update-and-deb-redist} M uni/utils/2tree/{list2tree => 2tree} M uni/utils/2tree/ChangeLog M uni/utils/2tree/Makefile.am However, some entries having long path names are abbreviated, such as uni/package/cooldeb/update-and-deb-redist is abbreviated to ...update-and-deb-redist. I deem I can do with Git directly, maybe I can configure git pull's output in special format. Any idea?

  Read the article

• Unable to resize ec2 ebs root volume

  - by nathanjosiah

  I have followed many of the tutorials that pretty much all say the same thing which is basically: Stop the instance Detach the volume Create a snapshot of the volume Create a bigger volume from the snapshot Attach the new volume to the instance Start the instance back up Run resize2fs /dev/xxx However, step 7 is where the problems start happening. In any case running resize2fs always tells me that it is already xxxxx blocks big and does nothing, even with -f passed. So I start to continue with tutorials which all basically say the same thing and that is: Delete all partitons Recreate them back to what they were except with the bigger sizes Reboot the instance and run resize2fs (I have tried these steps both from the live instance and by attaching the volume to another instance and running the commands there) The main problem is that the instance won't start back up again and the system error log provided in the AWS console doesn't provide any errors. (it does however stop at the grub bootloader which to me indicates that it doesn't like the partitions(yes, the boot flag was toggled on the partition with no affect)) The other thing that happens regardless of what changes I make to the partitions is that the instance that the volume is attached to says that the partition has an invalid magic number and the super-block is corrupt. However, if I make no changes and reattach the volume, the instance runs without a problem. Can anybody shed some light on what I could be doing wrong? Edit On my new volume of 20GB with the 6GB image,df -h says: Filesystem Size Used Avail Use% Mounted on /dev/xvde1 5.8G 877M 4.7G 16% / tmpfs 836M 0 836M 0% /dev/shm And fdisk -l /dev/xvde says: Disk /dev/xvde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x7d833f39 Device Boot Start End Blocks Id System /dev/xvde1 1 766 6144000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvde2 766 784 146432 82 Linux swap / Solaris Partition 2 does not end on cylinder boundary. Also, sudo resize2fs /dev/xvde1 says: resize2fs 1.41.12 (17-May-2010) The filesystem is already 1536000 blocks long. Nothing to do!

  Read the article

• How to (properly) back up a live QEMU/KVM VM?

  - by Roman

  I'm currently engineering a backup solution for KVM VM's as an additional measure to traditional backups. Unfortunately, all currently (August 2013) existing solutions I came across so far either: do not ensure a consistent backup of the VM (losing RAM state, creating a dirty image, or other things), or require lengthy downtime (complete VM shutdown while backing up). I'm aware of QEMU/libvirt's functionality of taking snapshots, however, it's not yet usable since: image-internal snapshots present you with an ever-changing image file, resulting in a likely dirty backup (assuming one uses qcow2 images at all). one cannot yet merge a currently active external snapshot into the original backing image ("blockcommit"). Out of the above reasons, I'm now implementing a script that: Saves the VM's state and halts it Sets up a devicemapper snapshot(s) where the VM's disk images and state reside Resumes the VM Mount the snapshot(s) of step 2. Backs up the VM's disk and state (configuration for convenience) Merges back the snapshot(s). If I got everything right, this will take consistent backups of VM's with only seconds (if at all, since 1-3 is fast, possibly sub-second) of downtime. Of course, when restoring, the VM will be way in the past, but at least giving me the option of an orderly shutdown/reboot. Am I missing something with this solution? Or has someone indeed already implemented this?

  Read the article

• How to start MSSQL Server with corrupt model db

  - by Jordan McGuigan

  After moving some databases around (restoring, deleting, etc) we experienced an issue creating new databases. Specifically, When trying to create a new database MSSQL Server it failed because the "The database 'model' is marked RESTORING and is in a state that does not allow recovery to be run". As some online solutions suggested, we tried to Start and Stop the MSSQL Service. Service would not restart because "Could not create tempdb. You may not have enough disk space available. Free additional disk space by deleting other files on the tempdb drive" (FYI: the drive has 100gb of free space). Tried restarting the machine the MSSQL Server is running on. When the server came back online, we received the same error. We have tried deleting tempdb.mdf and restoring the modeldb from the templates folder, but neither of these solved the issue. We are unable to connect to the database, even in single user mode. Many of the online solutions have us running SQL commands against the server, but we are unable to connect (even in single user mode) to the DB to run commands against the server. Specific error messages: Database 'model' cannot be opened. It is in the middle of a restore. (Microsoft SQL Server, Error: 927) The SQL Server (MSSQLSERVER) service is starting. The SQL Server (MSSQLSERVER) service could not be started. A service specific error occurred: 1814. We need the server up and running again ASAP.

  Read the article

• WIN7 constant BSOD 0x7B on boot, not producing any dump files where to go from here?

  - by prayingpantis

  So my one win 7 pc has been getting a BSOD on boot (roughly a sec after load screen starts) after a power failure. The complete stop code is 0x0000007B (0x80786B58, 0xC0000034,0x00000000,0x00000000) I've searched for quite a while now on the net and it seems like most people gave up after gettting 0x7B and no dump files. What I've tried so far: startup repair - reports it cannot repair computer automatically. BadPatch is reported somewhere in a problem signature contained in the problem details. startup repair with a WIN 7 CD - also fails, I can't recall what the error was, but it was not the same as the error produced with the start up tool shipped with the version of WIN 7 installed on my machine (I think the text had something ACL-ish contained in it) used a boot disk (Hiren's boot iso) - I used it to enable the CrashDump registry key and then after BSOD, read the HDD's dump locations but it was empty. Note, I'm quite sure the registry keys I edited are the correct ones, since the reboot on BSOD option was enabled by default and after I changed the regkey controlling this functionalitty to 0 the BSOD stayed after I booted again. check disk - works and returns no problems, also it seems I'm able to access all my files on the HDD. mem test - works and returns no errors So I'm not sure what else I can do to figure out what is the problem here. I read somewhere that you can use WINDBG to remote debug another PC, but I'm not sure if this is possible since the OS isn't even loaded yet? Also the last driver change I made on the system was installing a video driver, but I had no problems with it and were able to reboot several times until the power outage happened and the BSOD appeared. Any help or guidance for a way to DEBUG this problem would really be appreciated (I'm not really that keen to try a whole bunch of random fixes, I'd rather try and narrow down the problem first).

  Read the article

• Can't do anything with Ext. HDD, ".Trashes" is probably the boogyman. (On a MAC!)

  - by Sander Schaeffer

  I bought a external Harddrive today, A Samsung. But I'm not able to do anything with it A few notes on that. I can't put anything on the harddrive. It keeps on 'preparing copying files' I can delete anything on the harddrive system files, except the folder ".Trashes". It gives error 'Unexpected error: -50' I've tried to empty my own trashcan, no changes. I've set the file permission on the .Trashes to read/write everyone, doesn;t change a thing Trying to format the whole drive with DiskUtility, but quits at start, because the drive cannot be deactivated I've tried a few terminal commands sudo -s -r rf /Volumes/Untitled\ 1/.Trashes - Directory not empty -r rf /Volumes/Untitled\ 1/.Trashes - no permissions Also cd /Volumes ls -al cd name_of_partition ls -al -rm -rf .Trashes Again: Permission error. Also: I can't change drive permissions via Disk Utility, via the button 'recover drive permissions', because it is 'blank' I really can't figure out how to delete .Trashes, format the drive or get the damn thing working. Any suggestions? p.s. If this is the wrong Stack Exchange site: Please redirect me!

  Read the article

• MysqlTunner and query_cache_size dilemma

  - by wbad

  On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

  Read the article

• How to find what files / directories are not copied yet?

  - by user8676

  Hi all, I found the following 'nice' situation: An archive of few disks (actually three disks) which has a bunch of photos (more or less) organized. Well, this is good. A big disk shared on a network which has a bunch of photos which has another folder structure (even if is somewhat recognizable for a human being) than the archive described above, but some of the files on this big network share are the same with the files from the archive. Well, this is bad. What we need is to move the different (new) files from the network share in the archive (perhaps we'll use for this a new disk added to archive). The program that we need is different from a regular File Duplicate Finder program because usually the File Duplicate Finder finds the duplicates from all sources comparing each file with another. We want to find the differences between the two sources. It is fine for us to have a report generated in text file which after this we'll use to do our move. A Windows solution will be preferred. Any ideas? TIA

  Read the article

• What are the typical methods used to scale up/out email storage servers?

  - by nareshov

  Hi, What I've tried: I have two email storage architectures. Old and new. Old: courier-imapds on several (18+) 1TB-storage servers. If one of them show signs of running out of disk space, we migrate a few email accounts to another server. the servers don't have replicas. no backups either. New: dovecot2 on a single huge server with 16TB (SATA) storage and a few SSDs we store fresh mails on the SSDs and run a doveadm purge to move mails older than a day to the SATA disks there is an identical server which has a max-15min-old rsync backup from the primary server higher-ups/management wanted to pack in as much storage as possible per server in order to minimise the cost of SSDs per server the rsync'ing is done because GlusterFS wasn't replicating well under that high small/random-IO. scaling out was expected to be done with provisioning another pair of such huge servers on facing disk-crunch issues like in the old architecture, manual moving of email accounts would be done. Concerns/doubts: I'm not convinced with the synchronously-replicated filesystem idea works well for heavy random/small-IO. GlusterFS isn't working for us yet, I'm not sure if there's another filesystem out there for this use case. The idea was to keep identical pairs and use DNS round-robin for email delivery and IMAP/POP3 access. And if one the servers went down for whatever reasons (planned/unplanned), we'd move the IP to the other server in the pair. In filesystems like Lustre, I get the advantage of a single namespace whereby I do not have to worry about manually migrating accounts around and updating MAILHOME paths and other metadata/data. Questions: What are the typical methods used to scale up/out with the traditional software (courier-imapd / dovecot)? Do traditional software that store on a locally mounted filesystem pose a roadblock to scale out with minimal "problems"? Does one have to re-write (parts of) these to work with an object-storage of some sort - such as OpenStack object storage?

  Read the article

• Unnamed, hidden partitions on my 500 GB HD, HP Pavilion dm4 Laptop

  - by emotionull

  I have multiple doubts here. Its a Seagate 500GB 7200RPM HD. I had installed it few months back after my original Laptop HD stopped working. The current drives on my latop, as shown by the Windows Disk Management are: After installing the new HD, I had done a complete clean install of Windows 7 and I didn't create any parition myself, manually. So there are 4 drives. Even previously, before I installed this new HD, my laptop had 4 Partitions. But the there were no un-named partitions like the two in this case. The other two were HP tools and Recovery or something. It was pre-configured, Factory installed Windows. Also, now when I right cick on the unnamed Drives from Disk Management, all the options are greyed out (see image) except the delete partition image. So how do I know what's inside those partitions? Will it be ok if I delete them? I want install Ubuntu and dual boot it with my current windows installation. I cannot do it in current setup as there are already 4 partitions of my HD and if I will try to make a new partition, it will be a logical one (correct me if I am wrong here). So can I delete the un-named, hidden partitions and use them for Ubuntu? A bit unrelated question. As a backup option, can I use the Windows 7's Backup and Restore facility to keep a complete backup of all the drivers and system softwares.

  Read the article

< Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >