Search Results

Search found 23005 results on 921 pages for 'link lists'.

Page 324/921 | < Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >

• Problem with PXE boot

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• Windows 7 x64 wired connection problem. IP, gateway, dns assigned, can't ping. Network detected as "Network"

  - by Emil Lerch

  I am having a problem connecting to a specific wired network with my Latitude E6410 laptop. Other wired networks seem to work fine, but this one does not. I have a coworker with me with the same Intel 82577LM Gigabit Network card, and he can connect just fine. I've updated to the latest Intel drivers (11.8.75.0) and am not using Pro Set. I obtain all DHCP information just fine (IP, netmask, DNS server, default gateway). I cannot ping anything (internal or on the Internet - I tried pinging Google's public DNS servers by IP 8.8.8.8), nor can I get answers to any DNS queries through NS Lookup. Windows troubleshooting says everything is fine, but I can't get DNS responses. I've seen issues like this in the past that were related to link speed/duplex autonegotiaion failures, so I've tried manually setting link speed/duplex to all values one by one with no success. My coworker is using all default settings, so he is just using autonegotiate. Any ideas of other things to try?

  Read the article

• passing on command line options in bash

  - by bryan

  I have a question. I have a script, a kind of long script written in bash aprox. 370 lines. That has several functions and in those functions the user has to enter information which is then stored in files. ( This is suppose to represent a MySQL database, with the functions INSERT, UPDATE, SELECT, SELECT where x=y.) I created this myself in bash, now the only thing that rests me is that I need to be able to pass arguments on the command line to the script, that will do the same as the script does. I know that bash has positional parameters such as $1 $2 $3 $* $@ $0 ( refers to the name of the script) etc. I know how I can use these parameters in a simple if function. This is not enough for my script. I basicly need to do the same thing that the script does, but then from the command line. I have been struggling with this for a couple of days now and I cannot think of a way to get it to work. Maybe someone here can help me with this? If you want to have the script. That can be possible, but I don't think I can paste it in here... EDIT: Link to script, http://pastebin.com/Hd5VsDv2 Note, I am a beginner in bash scripting. EDIT: This is in reply to Answer 1. As I said I hope I can just replace the if [ "$1" = "one" ] ; then echo "found one" to if [ "$1" = "one" ] ; then echo SELECT where SELECT is the function I previously had in my script(above) http://pastebin.com/VFMkBL6g LINK to testing script

  Read the article

• How to configure router to give XBox top priority / most bandwidth?

  - by MrSparky

  Hi all - Newbie here so go easy... and apologies in advance if I blow the community etiquette / rules! Here's what I'm trying to do: I have a "D-Link DIR-655 Extreme N" wireless router and an XBox 360 w/ the old-style wireless connection thing (usb attachment)... I want to configure my router / network to give my XBox as much bandwidth as it wants, whenever it wants. I have tried giving the XBox a unique IP (within my network) and then tweaking the router to treat that IP as a top priority application (using the router's QOS stuff). Problem is whenever I turn off the xbox, I can't connect to the network the next time I start it up. It seems the only reliable setting in the XBox is to use "Automatic" for the IP settings within the Network Configuration area. Supposedly the D-Link ships with default settings that attempt to recognize a game console and give it top priority... but i've not seen good results (lots of stuttering / lag when someone else jumps online, etc). Any suggestions? thanks again!

  Read the article

• Architecture for highly available MySQL with automatic failover in physically diverse locations

  - by Warner

  I have been researching high availability (HA) solutions for MySQL between data centers. For servers located in the same physical environment, I have preferred dual master with heartbeat (floating VIP) using an active passive approach. The heartbeat is over both a serial connection as well as an ethernet connection. Ultimately, my goal is to maintain this same level of availability but between data centers. I want to dynamically failover between both data centers without manual intervention and still maintain data integrity. There would be BGP on top. Web clusters in both locations, which would have the potential to route to the databases between both sides. If the Internet connection went down on site 1, clients would route through site 2, to the Web cluster, and then to the database in site 1 if the link between both sites is still up. With this scenario, due to the lack of physical link (serial) there is a more likely chance of split brain. If the WAN went down between both sites, the VIP would end up on both sites, where a variety of unpleasant scenarios could introduce desync. Another potential issue I see is difficulty scaling this infrastructure to a third data center in the future. The network layer is not a focus. The architecture is flexible at this stage. Again, my focus is a solution for maintaining data integrity as well as automatic failover with the MySQL databases. I would likely design the rest around this. Can you recommend a proven solution for MySQL HA between two physically diverse sites? Thank you for taking the time to read this. I look forward to reading your recommendations.

  Read the article

• OpenWrt vs DDWrt

  - by Ioan Paul Pirau

  I have a TP-Link Wr1043ND router and I want to install one of these two firmwares: OpenWRT DD-WRT I read that I can install custom packages and do much more than I can with the original firmware. I would like to ask someone with experience in using both OpenWRT and DD-WRT which he would recommend and why. And to give a few reference points I'm interested in: reliability – network stability both on cable and wireless and on the usb drive performance – network speed, very important also usb drive speed configurability – the possibility to add extensions such as a torrent client, FTP, SSH, WWW and SVN server directly ease of use – the ease of installation and configuration of the router support/docs – how much info there is if you stumble upon a problem and you have to find some documentation, or if there's any free support (but that's a longshot) Of course I don't imagine that I will find the perfect firmware and that one is vastly superior over the other. Also if there's anyone out there who uses one of these firmwares on a TP-Link Wr1043ND, it would be great to get some feedback about the impact of the changes from the original firmware. P.S. I'm open also for Tomato if it's the better one.

  Read the article

• 100% iowait + drive faults in dmesg

  - by w00t

  Hi, I have a server on which resides a fairly visited web app. It has a raid1 of 2 HDDs, 64MB Buffer, 7200 RPM. Today it started throwing out errors like: kernel: ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen kernel: ata2.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in kernel: res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) kernel: ata2.00: status: { DRDY } kernel: ata2: hard resetting link kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: configured for UDMA/133 kernel: sd 1:0:0:0: timing out command, waited 7s kernel: ata2: EH complete kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) kernel: sda: Write Protect is off kernel: SCSI device sda: drive cache: write back All day long it has been in load higher than 10-15. I am monitoring it with atop and it gives some bizarre readings: DSK | sda | busy 100% | read 2 | write 208 | KiB/r 16 | KiB/w 32 | MBr/s 0.00 | MBw/s 0.65 | avq 86.17 | avio 47.6 ms | DSK | sdb | busy 1% | read 10 | write 117 | KiB/r 17 | KiB/w 5 | MBr/s 0.02 | MBw/s 0.07 | avq 4.86 | avio 1.04 ms | I frankly don't understand why only sda is taking all the hit. I do have one process that is constantly writing with 1-2megs but what the hell.. 100% iowait?

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• virtualisation with kvm: export services from guest to the host

  - by ascobol

  Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• 2560 x 1600 screen resolution not available when a second monitor is attached.

  - by sgmoore

  I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

  Read the article

• Distributed File Systems.

  - by GruffTech

  So, I've been reading several articles around ServerFault as well as google. (For Example, this link) My Requirements are very similar to the link above, however i'd like to also have dynamic or at least resizeable file volumes, so if necessary i can add 4-5 servers to the pool, and then expand the volume. Any Distributed File systems that support that, to save me some time? Thanks! LustreFS will be my next test cluster to build. GlusterFS I've build a 3-machine test GlusterFS cluster, However i quickly became aware of several of its limitations that it doesn't seem to make clearly public. One, i can't seem to resize a volume. Once a volume is created, its done. Which seems retarded, why have a fully scalable file system if i can't scale a volume? So maybe i'm doing something wrong. I'm not sure. AmazonS3 while gives the cheapest startup adds too much cost when broken down to per client per month, so its out. Building my own system when prorated over several years with no bandwidth costs makes it significantly cheaper. MogileFS isn't an option as we'd like this server to be a SAN-Replacement, for storing tons of media from a multitude of systems, which for us means it needs to be POSIX compliant so it can be remotely mounted via NFS or CIFS.

  Read the article

• What is the point of PPPoE?

  - by aaa90210

  I am trying to expand my knowledge of networking beyond the basics. I have started reading about PPP, and how it is used in DSL modems with PPPoE and PPPoA. My first impression of PPP was "well that seems pretty similar to Ethernet". They are both data link layer protocols. They both have fields to identify the encapsulated protocol (e.g. IP). They both have related protocols to assign IP addresses (DHCP and NCP). So my first question was "so what's the point of PPP, why not just use Ethernet?". The answer to that was fairly straightforward - Ethernet is not supported over a wide range of media like serial lines, and is a fairly specific technology to LAN's using CAT5 or similar. HOWEVER - then I was reading about PPPoE, and the obvious thought was "well if we are doing something over Ethernet, then Ethernet must be available and in use, so why not just use it?". In other words, PPPoE seems to be encapsulating one data-link layer protocol in another very similar protocol. Why do IP-inside-PPP-inside-Ethernet when we could just be doing IP-inside-Ethernet, and use DHCP rather than NCP to assign the IP address to the home router? Thanks

  Read the article

• IE9 apprears to be ignoring RewriteRule in htaccess file

  - by mouli

  I have a site that uses SEF URLs and htaccess RewriteRules to serve up the pages. This has worked fine for several years until the arrival of IE9. Now it appears that the links are not being rewritten and the site is dead in the water. I have tried different compatabilty modes, to no avail, and I've played with the Rewrite Rules over and over, tried different doctypes and a few other browser settings. I agree that it cannot in theory be a browser specific problem if the problem is with the htaccess file but this site works in IE8, firefox and chrome. I have run the rewriterule through a validator and it looks fine. Any ideas would be appreciated as I am running out of ideas. The site is www.marlboroughsounds.co.nz a sample link is http://www.marlboroughsounds.co.nz/walking/freedom-walk-queen-charlotte-track/4dfw and the rewrite rule thats not working looks like this: RewriteRule ^walking/.*/([a-z0-9_]*)/?$ /walking.php?act_code=$1 [L] The link fails and it serves up a browser 404 page, not even the custom 404 I have for the site. Any ideas would be much appreciated as I am stumped.

  Read the article

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• How to download Vim script on the command-line?

  - by HaiYuan Zhang

  Whenever I want to install a new Vim script on the Linux server I'm working on, my typical workflow is as the following: surf the plugin's homepage in Vim online using FireXXXX download a right version of the plugin to my laptop by click some highlighted link upload the downloaded plugin from my laptop to Linux server using WinSCP which is really inconvenient. I don't know what is the magic behind this: I mean for the same hyperlink I click it in web browser. I can let you download it but use Wget plus the hyperlink in Linux command-line will end up with nothing but an error indication. Hyperlink in the web browser. Otherwise I can get the link in web browser and then use Wget or some similar tool to actually do the downloding. I try new cool Vim scripts quite ofte , so you can imagine my dismay when I have to repeat the tedious action all the time. What are some tips which can let me download the Vim scripts in a more "professional" way? Post edit: My problem is not find a tool like Wget or cURL. The problem I met is quite specific; to use these tools to download a Vim script. Let's take http://www.vim.org/scripts/script.php?script_id=30 as an example. It's the normal place where one can get the script, at least for me. But I can't find an working URL from this page that can feed to Wget.

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• Can't make nodejs mingw32: pkg-config can't find gnutils

  - by valya

  I'm trying to compile nodejs using MSYS, mingw32 on Windows 7-64 Valentin Golev@VALYASNOTEBOOK /home/Valentin_Golev/nodejs $ ./configure Checking for program CL : ok C:\Program Files (x86)\Microsoft V isual Studio 10.0\VC\BIN\x86_amd64\CL.exe Checking for program CL : ok C:\Program Files (x86)\Microsoft V isual Studio 10.0\VC\BIN\CL.exe Checking for program CL : ok C:\Program Files (x86)\Microsoft V isual Studio 10.0\VC\BIN\amd64\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\x86_amd64\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\amd64\CL.exe Checking for program CL : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\amd64\CL.exe Checking for program LINK : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\amd64\LINK.exe Checking for program LIB : ok c:\Program Files (x86)\Microsoft V isual Studio 9.0\VC\BIN\amd64\LIB.exe Checking for program MT : ok C:\Program Files\\Microsoft SDKs\W indows\v6.0A\bin\x64\MT.exe Checking for program RC : ok C:\Program Files\\Microsoft SDKs\W indows\v6.0A\bin\x64\RC.exe Checking for msvc : ok Checking for msvc : ok Checking for library dl : not found Checking for library execinfo : not found Checking for gnutls >= 2.5.0 : fail --- libeio --- Checking for library pthread : not found Checking for function pthread_create : not found error: the configuration failed (see 'C:\\msys\\1.0\\home\\Valentin_Golev\\node js\\build\\config.log') I have gnutils built and installed! I've checked the config.log, and there was a command: pkg-config --errors-to-stdout --print-errors --atleast-version=2.5.0 gnutls I typed it in the console Valentin Golev@VALYASNOTEBOOK /home/Valentin_Golev/nodejs $ pkg-config --errors-to-stdout --print-errors --atleast-version=2.5.0 gnutls Package gnutls was not found in the pkg-config search path. Perhaps you should add the directory containing `gnutls.pc' to the PKG_CONFIG_PATH environment variable No package 'gnutls' found But, Valentin Golev@VALYASNOTEBOOK ~ $ $PKG_CONFIG_PATH sh: c:/msys/1.0/local/lib/pkgconfig: is a directory Valentin Golev@VALYASNOTEBOOK ~ $ cd $PKG_CONFIG_PATH Valentin Golev@VALYASNOTEBOOK /local/lib/pkgconfig $ ls gnutls-extra.pc gnutls.pc What am I doing wrong?

  Read the article

• Break all hardlinks within a folder

  - by Georges Dupéron

  I have a folder which contains a certain number of files which have hard links (in the same folder or somewhere else), and I want to de-hardlink these files, so they become independant, and changes to their contents won't affect any other file (their link count becomes 1). Below, I give a solution which basically copies each hard link to another location, then move it back in place. However this method seems rather crude and error-prone, so I'd like to know if there is some command which will de-hardlink a file for me. Crude answer : Find files which have hard links (Edit: To also find sockets, etc. that have hardlinks, use find -not -type d -links +1) : find -type f -links +1 A crude method to de-hardlink a file (copy it to another location, and move it back) : Edit: As Celada said, it's best to do a cp -p below, to avoid loosing timestamps and permissions. Edit: Create a temporary directory and copy to a file under it, instead of overwriting a temp file, it minimizes the risk to overwrite some data, though the mv command is still risky (thanks @Tobu). # This is unhardlink.sh set -e for i in "$@"; do temp="$(mktemp -d ./hardlnk-XXXXXXXX)" [ -e "$temp" ] && cp -ip "$i" "$temp/tempcopy" && mv "$temp/tempcopy" "$i" && rmdir "$temp" done So, to un-hardlink all hard links (Edit: changed -type f to -not -type d, see above) : find -not -type d -links +1 -print0 | xargs -0 unhardlink.sh

  Read the article

• How can i use the `eject` command on a computer i have SSH'd into?

  - by will

  So if i do eject on my machine, it works exactly as expected, however, if i ssh into the machine next to me, and do the same thing, it does not work... my computer: eject: using default device `cdrom' eject: device name is `cdrom' eject: expanded name is `/dev/cdrom' eject: `/dev/cdrom' is a link to `/dev/sr0' eject: `/dev/sr0' is not mounted eject: `/dev/sr0' is not a mount point eject: checking if device "/dev/sr0" has a removable or hotpluggable flag eject: `/dev/sr0' is not a multipartition device eject: trying to eject `/dev/sr0' using CD-ROM eject command eject: CD-ROM eject command succeeded other computer: eject: using default device `cdrom' eject: device name is `cdrom' eject: expanded name is `/dev/cdrom' eject: `/dev/cdrom' is a link to `/dev/sr0' eject: `/dev/sr0' is not mounted eject: `/dev/sr0' is not a mount point eject: checking if device "/dev/sr0" has a removable or hotpluggable flag eject: `/dev/sr0' is not a multipartition device eject: unable to open `/dev/sr0' if i look in the /dev/ dir, then i find cdrom which is a symlink to sr0 - as mentioned by the verbose outputs of eject -v. On my machine, if i try and look at it, if the drive is open, it will close it, and then give this: $ less sr0 sr0 is not a regular file (use -f to see it) so $ less -f sr0 sr0: No medium found but if i do it on the other computer, $ less -f sr0 sr0: Permission denied so i look at the files more, and get this on both machines: $ ls -la sr0 brw-rw----+ 1 root cdrom 11, 0 Nov 12 10:13 sr0 Does anyone know a way around this? I do not have root access.

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

< Previous Page | 320 321 322 323 324 325 326 327 328 329 330 331  | Next Page >