Search Results

Search found 62172 results on 2487 pages for 'windows networking'.

Page 327/2487 | < Previous Page | 323 324 325 326 327 328 329 330 331 332 333 334  | Next Page >

  • Problems with wired ethernet connection Ubuntu 11.10

    - by Andrew Fielden
    After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

    Read the article

  • How to switch off wifi on startup or from the console

    - by mit
    I have installed ubuntu 10.04 on a laptop. Wifi is switched on by default on startup. I can disable it rightclicking the network manager icon in the gnome bar. How can I set it to have wifi switched off as default? Alternatively, how can I switch off wifi on the console? I tried already the rfkill command but it does not list any devices and it does not switch off wifi, I tried different parameters. This is a standard install of the Ubuntu 10.04 i386 Desktop Live CD on an IBM T40 Laptop. EDIT A: This is the output of some rfkill commands on my system, and it does not affect the wifi of the laptop: $ rfkill --help Usage: rfkill [options] command Options: --version show version (0.4) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: <idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm $ rfkill list $ rfkill list wifi $ rfkill list all $ rfkill list wlan $ sudo rfkill list all $ sudo rfkill block all $ sudo rfkill block wlan $ sudo rfkill block wifi $ EDIT B: Now I found out that sudo ifconfig eth1 down turns it off. And I can turn it on through the gnome network applet again. But the applet does not reflect the change from the commandline, it stills believes wifi is switched on. I have to switch it off and on again on the applet to switch it on again, when I switched it off from the console. Is there a better way? This is what the syslog looks like when I switch wireless off and on again from the network manager: NetworkManager: <info> (eth1): device state change: 3 -> 2 (reason 0) NetworkManager: <info> (eth1): deactivating device (reason: 0). NetworkManager: <info> Policy set '24' (eth0) as default for routing and DNS. NetworkManager: <info> (eth1): taking down device. avahi-daemon[660]: Withdrawing address record for fe80::202:8aff:feba:d798 on eth1. kernel: [ 971.472116] airo(eth1): cmd:3 status:7f03 rsp0:0 rsp1:0 rsp2:0 NetworkManager: <info> (eth1): bringing up device. NetworkManager: <info> (eth1): supplicant interface state: starting -> ready NetworkManager: <info> (eth1): device state change: 2 -> 3 (reason 42) avahi-daemon[660]: Registering new address record for fe80::202:8aff:feba:d798 on eth1.*. kernel: [ 965.512048] eth1: no IPv6 routers present

    Read the article

  • C# Toolbox: Debug-able, Self-Installable Windows Service Template Redux

    - by James Michael Hare
    I had written a pair of posts before about creating a debug-able and self-installing windows service template in C#.  This is a template I began creating to ease creating windows services and to take some of the mundane tasks out of the coding effort.  The original posts were here: C# Windows Services (1 of 2) - Debug-able Windows Services C# Windows Services (2 of 2) - Self-Installing Windows Services But at the time, though I gave the code samples I didn't have a downloadable for of the template on the blog.  After getting many requests for the actual source, I zipped it up and am posting it with this blog entry.  Click on the link below to download the archive.  The password on the archive is, imaginatively enough, password.  Hope you enjoy and please feel free to comment and suggest changes! Debug-able, Self-Installing Windows Service Template download Enjoy! Tweet Technorati Tags: C#,Windows Service,Toolbox

    Read the article

  • Can't connect to hidden network with BCM4313

    - by poomerang
    The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

    Read the article

  • Is it possible to set a VPN through Tor? and have functionality for Software Updates?

    - by moazhmi
    Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

    Read the article

  • How to install seleniumHQ for Python on Windows?

    - by Katie
    I would like to know how to install SeleniumHQ (http://seleniumhq.org/download/) on Windows XP/Vista/7? On Ubuntu/Debian system you need to just type those commands: $ sudo apt-get install python-pip $ sudo pip install selenium $ sudo apt-get install python-pip xvfb xserver-xephyr $ sudo pip install selenium and then I can do this: #!/usr/bin/env python from selenium import selenium # ... but how about Windows? Thanks for any help (I know where to find Selenium doc but still - would anybody be so kind to give me some steps: I mean, download this, do that ...) THANKS:)

    Read the article

  • Wireless is disabled by hardware switch on Dell Inspiron 1750

    - by lowerkey
    I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

    Read the article

  • Selecting primary Internet connection in Windows XP

    - by Mariusz
    There is a computer that has access to the Internet both via the local network and by a GSM modem. As far as I know, when both connections are active, the modem connection is the primary one and all data is transmitted by the modem. Because of the fact that the slow modem connection is supposed to be used as a backup connection, I want Windows to use it only when the connection via LAN is unavailable. At the same time I want the GSM modem connection to be active constantly. Is it possible to make Windows not use modem connection when there is a working LAN Internet connection? Thanks for your help in advance, Mariusz.

    Read the article

  • Suggestions for Troubleshooting WIndows 7 lockups

    - by Craig L
    I've got a Dell Latitude E6500 that was working fine under Vista x64. I got one of the new Seagate 500GB Hybrid SSD/HD 2.5 drives and thought.. hmm.. let's try Win 7 x64 on it. Bottom line: It works great for hours and then it will hard lock. I don't mean BSOD (or whatever the Win7 equivalent is). I mean my screen is displaying a static image (if there is a clock displayed, it will be frozen at the time the lockup occurred) and the mouse and keyboard do not work. Control-Alt-Delete will not work. I have to hold down the power button to reboot. The event log records NOTHING at the time the lockup occurs. Obviously something is happening to the system to cause the lockup, but the default Windows 7 x64 doesn't log it. How can I log the things Windows doesn't normally log in Event Viewer ?

    Read the article

  • Nvidia Optimus shows Nvidia card is always active in Windows 8

    - by Ty Underwood
    I have loaded the new Asus Nvidia driver for my Asus Ux32VD that I have installed Windows 8 on. It has an Nvidia 620m and Intel hd 4000 integrated graphics. The problem is that the Optimus activity icon in my system tray shows that the Nvidia card is always active, though it shows that it is not doing anything. I can force the system to prefer the Intel graphics, and after rebooting, the Nvidia card will shut off, but then all the programs will be overridden and use the Intel graphics. Is anyone else having problems with Optimus in Windows 8? My battery life is really suffering because I'm always idling my Nvidia card while also presumably running the Intel card. Any suggestions would be appreciated.

    Read the article

  • Why can't windows see mmcblk0p3? [closed]

    - by jacknad
    The partition is created on the embedded linux target like this # n - new # p - partition # 3 - partition 3 # 66 - starting cylinder # <blank> - maximum size for the ending cylinder # t - set file system type # 3 - partition 3 # c - set to windows vfat # w - write partition table and exit echo -e "n\np\n3\n66\n\nt\n3\nc\nw" | fdisk /dev/mmcblk0 The file system is then formatted on the embedded linux target as MS-DOS like this # -n volume-name # -F FAT-size mkfs.vfat -n DB -F 32 /dev/mmcblk0p3 A linux host can mount and access files in mmcblk0p3 without issue. Why can't windows? Edit: Although the default number of FATS is 2 I tried adding -f 2 [number-of-FATs] since this is actually being done by busybox on an embedded platform but this didn't help. I understand the Linux MS-DOS file system does not support more than 2 FATs but there are only 2 on this target (the boot is also FAT which is visible), along with and EXT3 (on p2) for the root file system.

    Read the article

  • network manager says "device not managed"

    - by Daniella Glover
    I used to be able to share my network connection by editing the Auto Eth0 to share with other computers in the Ipv4 section and now I upgraded my laptop to 11.10 . Now are there no wired connections in the network manager. When I click my connections applet at the top of the tray it also says wired device not managed! when I type ifconfig -a daniella@daniella-1001HA:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 90:e6:ba:83:d6:fc UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 eth0:avahi Link encap:Ethernet HWaddr 90:e6:ba:83:d6:fc inet addr:169.254.13.40 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:45 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:25:d3:90:43:41 inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe90:4341/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12881 errors:0 dropped:0 overruns:0 frame:0 TX packets:12867 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8851081 (8.8 MB) TX bytes:2343199 (2.3 MB)

    Read the article

  • Windows Server 2003 not automatically assigning drive letter to external drives

    - by Chris
    My newly rebuilt Windows Server 2003 doesn't automatically assign drive letters to external usb devices. I have to manually open the Disk Management Console and assign it a drive letter every time. It does this with two different drives in all USB ports. I have been doing some reading and I don't have any network drives, I have also already tried USBDLM and it doesn't seem to have made any difference. Specs: ProLiant ML150 G5 with Windows 2003 Enterprise and all updates installed. Any ideas on what I can try to resolve this problem would be greatly appreciated. Chris

    Read the article

  • Tracking down random BSOD on windows 7

    - by pehrs
    I have gotten a computer running windows 7 handed to me that randomly, several times a day, bsods with a PAGE_FAULT_IN_NONPAGED_AREA (50) or WHEA_UNCORRECTABLE_ERROR (124). Crashes happens regardless of load. I am running out of ideas for how to track this down. Analyzing the minidumps shows the crash to be in ntkrnlmp.exe/WMIADAP.exe System has plenty of power (600w) Ram checks out fine using memtest86+ over a weekend. System is clean inside. No dust build up. Temperatures stay low. As far as I know (and reliability history shows) no new drivers were installed for several months before the problems started. All drivers are now up to date. sfc /scannow reports the system as clean. CHKDSK reports the disks as clean Removing the AV (Avast) has no effect. Any more things that should be tried on windows 7 before I start replacing the hardware?

    Read the article

  • Recovering a Windows XP License key

    - by Fortyrunner
    I threw out a Windows XP machine a while ago (the motherboard failed). I kept the hard drive and the XP installation media. Problem is the license key was on a sticker on the machine - doh! The original manufacturer has gone bust (Evesham) and I suspect that Microsoft will be of little help. Is there any easy way to get the license key off the hard disk? Can I just find the file with the registry data in it and get the key using a hex editor? I really need a spare XP key for use in a Windows VM.

    Read the article

  • Booting a Windows 7 installation on different hardware

    - by tomfanning
    I'm in a situation where I could do with very quickly migrating a Windows 7 (RTM x64) installation from one machine to another. What options are open to me in terms of getting W7 to boot after the drive is picked up and moved from one box to another? I thought it was supposed to be a little less sensitive to this kind of move than XP, but it doesn't work - it is stuck in a reboot loop and never reaches a GUI. Tried a few things so far, none of which have worked: Changed SATA mode in the BIOS of the target machine between ATA and AHCI run Windows 7 Startup Repair tried safe mode, no change (I will keep this list up to date as suggestions come in) UPDATE: I can confirm this reboot loop is due to STOP error 0x0000007B, and these codes follow: 0xFFFFF880009A98E8 0xFFFFFFFFC0000034 0x0000000000000000 0x0000000000000000 UPDATE: I didn't get anywhere on this and I ended up just rebuilding the machine. I think it should be theoretically possible, so I'm going to leave the question open in case someone comes along in future with an answer.

    Read the article

  • Intermittent ethernet connectivity

    - by Amey Jah
    I am facing a weird problem. I am connecting to my dsl modem via ethernet. After booting, sometimes Ubuntu 10.10 does not detect the eth0 card properly or does not connect to the modem. I have made the following observations: My modem is fully on. All indicators are on except ethernet, which is blinking continuously. My network indicator applet informs me that I am connected to modem, but I am not able to browse as it has not established connection with modem. I need to power off and on (restart) the modem several times OR disconnect/connect (via network applet) several times, before the system can establish a connection with the modem. Once it establishes the connection, the ethernet LED (on modem) stops blinking and glows continuously. However, I do not see this problem every time I reboot or start my computer. 3/5 time, it connects to the modem in a single attempt. Friends, I am not able to understand root cause of this problem. Plus I do not know what kind of logs should be attached. If you want any logs please give me command to run, and I will paste the result for you. Note: I ran system testing when above problem happened. Follow this link to download result.

    Read the article

  • Trouble accessing network drives in Windows 7

    - by Warlax
    Hi, Recently purchased a LaCiE network drive. Connected it to my router, configured it, added a user for myself. Installed the "Network Assistant" that came with it - no problem. Went to My Computer Network, found the network drive - was prompted for a login/password to see the contents, types \user and password (leading slash to get rid of DOMAIN) and accesses contents. There is one open share that I can access/mount without problem and there's another share with my user name as set-up via the network drive's web-based config. Double-clicked on that, prompted again. user/password doesn't work! It says I have no permissions but the user/pass combination is PERFECT. Some Windows Vista posts talk about a Local Security Policy menu - but that's nowhere to be found. Any ideas? (Windows 7 Professional BTW).

    Read the article

  • Start jade via batch script as service on windows server 2012 amazon ec2 instance

    - by E. Lüders
    I would like to start the Jade agent platform with a batch script on an windows server ec2 instance as a service. The reason for this is, that I want to start jade automatically at system startup. For creating the service I use nssm. However so far its working fine and the service is created. When I want to start the service I get an error message: Windows could not start the NAME service on Local Computer. The service did not return an error... My batch file contains only one line: java jade.Boot -platform-id P%random% If i execute the script via cmd it works fine. Anybody got an idea why this is not working if I start the batch script as a service?

    Read the article

  • Deploying an application on a windows domain

    - by ALOToverflow
    I'm looking for different ways to deploy, execute and uninstall an application on all machines of a Windows domain. I've did some research on Group Policy Object (GPO) but I'm still looking for other ideas. As I said, I need to deploy the application, run it without the user having to click anything and letting him to control over the machine. Once it's finished running I need to uninstall it and never run it again. Can such things be done with a GPO? Are there any other possibilites on a Windows domain? Thank you

    Read the article

  • RPC protocols comparison

    - by Ricardo
    I have to select a protocol/technology to use for communicating a client-server architecture, with support both for Python and C. The main requirements are: Symmetrical communication in between ends: clients establish a connection and servers can send data back to clients through the same connection. Avoid excessive overhead by using HTTP or a big stack (if possible, TCP direct communication). TLS/SSL support for secure communications. Ease of implementation. For that, I evaluated the following protocols/communications technologies. Is the information on this table accurate and correct? (*1) TLS support for RPyC is based in a no-longer supported Python library.

    Read the article

  • No Wireless In Ubuntu 13.10

    - by viktorhubinette
    When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Read the article

  • Ping Access to a Nested VM !! Plz Help

    - by Shivaramakrishnan
    I have a problem in communication between the host and the nested VM.This is my layout. I have installed KVM on host machine having a single nic interface (public ip) running Ubuntu.On top of this,I have VM running Ubuntu.I have installed KVM in this VM too.I then have a VM inside this running a web server. I am able to ping the host from this web server VM and ssh into it.But from host to VM ,ping is being unsuccessful. The VM (named L1hyp) on host was created using libvirt-manager and has IP of 192.168.122.8. The vswitch interface created at host is in default config (NAT-ed). Its IP is 192.168.122.1. Now this VM is also having a vswitch interface which is in default config (NAT-ed).Its IP is 192.168.100.1. The Web server VM is created on top of this L1hyp VM, is having an IP of 192.168.100.186. The Webserver VM uses 192.168.100.1 as its default gw. The L1hyp uses 192.168.122.1 as its default gw. From Host: ping 192.168.122.8 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS ping 192.168.100.1 - SUCCEEDS ping 192.168.100.186 - FAILS Comes up with Destination Host Unreachable From 192.168.122.1. But there is route to 192.168.100.0/24 subnet from host.Ping to 192.168.100.1 succeeds. From Webserver VM: ping 192.168.100.1 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS SSH from web server VM to host succeeds. Can anyone help me out what needs to be modified to have two way communication between the host and Webserver VM at the earliest? I am pondering over this problem for over a week now.

    Read the article

  • Can someone correct me about Windows 2008 DFS implementation

    - by cwheeler33
    I have 2 two Windows 2003 file servers using DoubleTake at the moment. They are in an 2003 AD domain. And each server has it's own disk set. It is time to replace the servers... I want to use Windows 2008 64bit Ent. I was thinking of using DFS-R to replace DoubleTake. The part I'm not sure about is clustering. Do I need to have shared storage if each server has a copy of the data? I want to have the data available to the same share name, so maybe I don't fully understand how DFS is set up. I currently have about 6TB of data. I expect to grow by 3TB a year on these file servers. Any resources/books that could teach me would be good to know as well.

    Read the article

< Previous Page | 323 324 325 326 327 328 329 330 331 332 333 334  | Next Page >