Search Results

Search found 62172 results on 2487 pages for 'windows networking'.

Page 326/2487 | < Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >

• Direct X-forwarding

  - by Sean Houlihane

  I'm struggling to set up X-forwarding between 2 different machines on my local network and my ubuntu desktop. I'm able to connect using ssh x-forwarding one one machine, but the other machine (a Qnap TS-219P II) seems to have a less functional build of SSH on it, and I'd rather use a simpler approach. I've set $DISPLAY, and done 'xauth list $DISPLAY' on the desktop, then 'xauth add ' on the remote machine. From the remote machine, I just get xterm xterm Xt error: Can't open display: 192.168.0.4:0.0 Now, oddly, if I connect via ssh -X, there is a different magic cookie for the tunnelled port (but neither seems to work). I'm wondering if there is a port which needs to be enabled to permit X connections from the LAN? If so, how? The proper solution might be to re-build all the packages which are preventing X-forwarding from working on my QNAP machine, but lets assume for the purposes of this question that I've tried building enough packages on that architecture already and want to run X without the overhead of encryption.

  Read the article

• Acer Aspire 5719 with Windows XP does not boot

  - by Sri

  Hi, I have an Acer Aspire 5710 which came pre-loaded with Windows Vista. O/S has been changed to Win SXP SP2 and was working fine till today. The laptop starts up and then hangs (does not reach till the Windows screen). Have tried the following Repair with XP CD. Re-install with XP CD (In both cases the error "No hard disk" is displayed.) Tried F5/F8 to boot with other options. Guess the hard-disk is not being recognised. The 160 Gb SATA disk is shown as IDE0 in the Phoenix Bios. There is no floppy drive. Any suggestions. Thanks, Sri.

  Read the article

• sound clipping in windows 7 64bit

  - by Sonic Soul

  something is up with 64 bit version of windows 7. i have 2 (good pro-sumer) sound cards which i've used in other version of windows 7 w/out problems, but now it is causing severe clipping (noise, sound having little gaps surrounded by static).. the cards i am using is echo mia, and native instruments audio kontrol 1. the audio kontrol 1 is a external card, and would work ok for a few hours after rebooting, and than it would go back into clipping mode, to the point where you tube videos would not play from trying to process sound and it stopping for extended periods of time. echo mia is performing better, but there is still some clipping and distortion. the machine i use is newly built, with i7 920 64 bit cpu, 6 gigs of ram and an outdated nvidia video card (geforece 7950 gx2)

  Read the article

• Broadcom bluetooth driver for Windows 7 on MacBook Pro

  - by Sergiy Byelozyorov

  I have installed Windows 7 on MacBook Pro using BootCamp. Usually when turning my Bluetooth headset on and trying to pair it with Mac for the first time, Windows would fail to install drivers and open solution in Action Center, which suggests to download the driver from the Broadcom webpage. This worked before and drivers would install and work. However now, when I start driver installer, it would get stuck at "Detecting Bluetooth Device" stage. Below the steps there is also a warning with text, which says "Please plug in or turn ob your Bluetooth device". This is how the installer looks like when it's stuck: I have tried turning my headset on/off, bringing it into pairing mode, installing/uninstalling device to/from the Bluetooth Devices. None of these worked. Any ideas?

  Read the article

• Moving AI in a multiplayer game

  - by Smallbro

  I've been programming a multiplayer game and its coming together very nicely. It uses both TCP and UDP (UDP for movement and TCP for just about everything else). What I was wondering was how I would go about sending multiple moving AI without much lag. At first I used TCP for everything and it was very slow when people moved. I'm currently using a butchered version of this http://corvstudios.com/tutorials/udpMultiplayer.php for my movement system and I'm wondering what the best method of sending AI movements is. By movements I mean the AI chooses left/right/up/down and the player can see this happening. Thanks.

  Read the article

• No HDMI audio - Windows 8 - ASUS H81M-PLUS

  - by Paul Wright

  I have an issue with HDMI audio on Windows 8 using an ASUS H81M-PLUS motherboard (without an external GFX card). There are many forum posts advising you to go into playback devices and setting HDMI to be default - I have done this. To eliminate what works and what doesn't work: I have not been able to get sound from my HDTV using HDMI. I have used this HDMI cable with my PS3, so this cable should be fine. I am able to use the HDMI cable in extended mode, so that I have two monitors (including the TV), just no audio. This HDMI cable goes straight from the motherboard to the TV. Below I have included 'Device manager', and 'Playback Devices' (Sound). Device Manager Playback Devices, showing disabled and disconnected devices I am at a loss. I have uninstalled all drivers, and then rebooted and made windows look for the correct ones, made sure the HDMI device was default. Thanks, Paul

  Read the article

• 'DNS server isn't responding' error in windows 7 home premium

  - by pradeeptp

  Hi All, I bought a brand new Dell Studio 1558 just last week. It has windows 7 home premium 64-bit installed on it. My friend who is occupying the adjacent room has a laptop with windows XP. Both of us are connecting to the same wireless router of the hotel. My friend is able to connect to the wireless network without any trouble, but when I try to connect, I get the error "DNS service isn't responding". I get this error when I run the troubleshooting option. I met two more people in the same hotel with win XP laptop and they too dont have any problem. I have gone to possibly all the forums and website but I haven't been able to fix this error :(. I have done all the basic troubleshooting but I have no luck yet. Pls help. Following is one forum where the problem seem to have been trouble shooted but not for all. http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/eeb84518-903d-46d1-9398-80cf211878d7

  Read the article

• Best way to implement mouse-based movement in MMOG

  - by fiftyeight

  I want to design an MMO where players click the destination they want to walk to with their mouse and the character moves there, similar to Runescape in this manner. I think it should be easier than keyboard movement since the client can simply send the server the destination each time the player clicks on a destination. The main thing I'm trying to decide is what to do when there are obstacles in the way. It's no problem to implement a simple path-finding solution on the client, the question is if the server will do path-finding as well, since it'll probably take too much Computation power from the server. What I though is that when there is an obstacle the client will send only the first coordinate it plans to go to and then when he gets there he'll send the next coordinate automatically. For example if there is a rock in the way the character will decide on a route that is made of two destinations so it goes around the rock and when it arrives at the first destination it sends the next coordinate. That way if the player changes destination is the middle he won't send unnecessary information. Is this a good way to implement it and is there a standard way MMOGs usually do it? EDIT: I should also mention that the server will make sure all movements are legal and there aren't any walls in the way etc. In the way I wrote it should be quite easy since all movements will be sent in straight lines so the server will just check there aren't any obstacles along that line.

  Read the article

• Create personal wireless network on laptop

  - by TechGuru

  I have a WiFi Network, now I have connected my laptop to the WiFi Network. And it is working fine I'm able to access the internet via WiFi. But I want to create other network on my laptop so that I can connect my mobile phone to the my laptop network. Means, my laptop is already connected to WiFi network (xyz). Now I want to create one wireless network on my laptop. So that I can connect my mobile phone to laptop network and access the internet on mobile. But I don't want to lost my `laptop and WiFi connection that is already connected. I tried to create the wireless network on my laptop, but when I created my personal wireless network I lost my wifi-laptop connection. I don't know it is possible or not.

  Read the article

• Partition table correpted in windows 7 machine as simple dynamic partition

  - by raki

  I have Windows 7 installed in my system. When I originally partitioned it I made 3 partitions and 16 gb space as unallocated. Later I tried to create a partition using this free space using diskmanagement tool. It shows free space as unusabe space and the only one option available is to make it as a simple partition. Unfortunately I made it as simple partition and all my partitions converted to simple dynamic partition. Now after reboot the OS is not loading. I tried to reinstall the OS by formatting the C drive, but it doesn't work. Now I can't load the OS properly. How can I install Windows 7 on my system without losing my data on the other two drives?

  Read the article

• How to run a local and external website on same computer with 2 NIC's, 2 Routers and 3 seperate networks?

  - by CandN

  Hello and hopefully I can get some answers to my question, though I think I'm making it more complicated for myself than it has to be. My business is a used auto dealership, and I'm in the process of connecting it to the world - via ethernet from the business server [running Xubuntu] to the ISP's ethernet router/modem, so that I can host our own website (no more than 5-10 people probably visiting at any time - mainly paying their bill), as well as set up a web based internal-intranet site - via DD-WRT Router on the 2nd NIC on the business server - that'll be accessed over Wifi from employees personal devices. On the other end of this is trying to offer free wifi to customers that is completely seperate of the 2 mentioned above networks. Quick Rundown: 1. Web Site for Customers to access. I'm going to use no-ip.org for DNS for the moment being, so I'll have a site that customers can access from anywhere in the world at "mybiz.no-ip.org". This will be forwarded to NIC #1 on the server, possibly at an address like "108.69.." as its being provided an IP from the ISP's modem/router, that is from Time Warner, and they allow NO! configuration options. Web Site for employees to access. I'm trying not to use the server too much as a desktop, only for critical situations, so having a backend thats seperate from the front-facing website is critical. This will be the DD-WRT router hardwired into NIC #2 on the server. This WiFi will be password accessible. Public WiFi for customers. The DD-WRT can seperate networks if I'm correct, I just can't seem to understand how to seperate the 2 and still have internet access on both. I've done it before, but the "Public" wifi (with no password set to connect) kept dropping the connection like a problem was happening that I couldn't figure out. So if I could do a little drawing, this is how it would/should possibly look. ISP -- [Sends Public Facing IP of 108.69.*.1/8] -- ISP Modem Router ISP Modem Router (Ethernet Only) -- [Gives Private IP 108.69.*.2] -- Server NIC #1 Server NIC #1 -- [Gives Private IP 108.69.*.3] -- DD-WRT Router DD-WRT Router -- [DHCP Enabled Giving IP's 172.16.0.0/16] -- Employees Network | | --------- [DHCP Enabled Giving IP's 192.168.1.0/24] -- Public WIFI Hope it's not too confusing, but it anyone could give me some good direct tutorials on how to accomplish this, or if YOU know, then it'll be alot of help. Thanks to all in advance. Need anything else to be explained? Don't hesitate to ask! *Using The LAMP stack with Webmin/VirtualMin -Customer site is located in /var/www2/ -Private Employees site is located in /var/www/ Using no-ip.org's dynamic client updater

  Read the article

• Reconstruct a file from a TCP stream

  - by Abhishek Chanda

  I have a client and a server and a third box which sees all packets from the server to the client (but not the other way around). Now when the client requests a file from the server (over HTTP), the third box sees the response. I am trying to reconstruct the file there. I am using libpcap to capture TCP datagrams and trying to reconstruct the file there. Here is what I did Listen for packets on an interface Group all packets which have the same ACK number Sort the group based on SEQ number Extract data from each packet and combine them and write to the disk The problem is, the file thus generated is not exactly the same as the original file. Does everything sound correct here? Some more details: I am using C++ The packet data is being stored as std::vector<char> I did change the byte order while reading the ack number and seq number from the packet using ntohl I am not sure if I need to change the byte order for the data as well. I tried to reverse the data from each packet before combining them, even that did not work. Is there something I am missing?

  Read the article

• Multiplayer Network Game - Interpolation and Frame Rate

  - by J.C.

  Consider the following scenario: Let's say, for sake of example and simplicity, that you have an authoritative game server that sends state to its clients every 45ms. The clients are interpolating state with an interpolation delay of 100 ms. Finally, the clients are rendering a new frame every 15ms. When state is updated on the client, the client time is set from the incoming state update. Each time a frame renders, we take the render time (client time - interpolation delay) and identify a previous and target state to interpolate from. To calculate the interpolation amount/factor, we take the difference of the render time and previous state time and divide by the difference of the target state and previous state times: var factor = ((renderTime - previousStateTime) / (targetStateTime - previousStateTime)) Problem: In the example above, we are effectively displaying the same interpolated state for 3 frames before we collected the next server update and a new client (render) time is set. The rendering is mostly smooth, but there is a dash of jaggedness to it. Question: Given the example above, I'd like to think that the interpolation amount/factor should increase with each frame render to smooth out the movement. Should this be considered and, if so, what is the best way to achieve this given the information from above?

  Read the article

• Trying to configure samba share with office server

  - by tomphelps

  Hi, i'm trying to set up fstab to automatically connect to my office shared server. I'm undoubtedly doing something silly here as the username and password and server name work fine in the first code snippet below, just not the second - any help would be appreciated! The following command works as expected... tom@tom-desktop: sudo /usr/bin/smbclient -L Server.local -Uguest Enter guest's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Sharename Type Comment --------- ---- ------- Lacie Disk Disk macosx Server Disk macosx IPC$ IPC IPC Service (Server) ADMIN$ IPC IPC Service (Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Server Comment --------- ------- ACER-9D60040D10 SERVER Server Workgroup Master --------- ------- WORKGROUP ACER-9D60040D10 But when i add the following line to /etc/fstab, i get this error: cifs_mount failed w/return code = -22 //Server.local/Server /media/maguires cifs username=guest,password=password 0 0

  Read the article

• Write permission when mounting Windows shares from Ubuntu

  - by Ola Tuvesson

  I think I'm close to having my dev environment set up exactly the way I want, but one final snag remains. I'm running VirtualBox on a Windows 7 64bit host, with my dev enviroment inside a Ubuntu 12.04 guest. I want to keep the files for my projects on the host filesystem - partly so I can access them when the Ubuntu guest is not running, but also so I can use Tortoise and other Windows based tools (cough Photoshop), and it also eases my backup scheme somewhat. So I've got a folder "Rails" on my NTFS drive, which I've shared from the host with a user specifically created for the Ubuntu guest. The mount point has been set up and an entry added to fstab (cifs), using a credentials file and the options iocharset=utf8,file_mode=0777,dir_mode=07??77 This mounts fine and my Ubuntu user has both read and write permissions to the contents, but when I try to start my Rails app I get permission errors on any files the app needs to write to (e.g. the log file). What gives?

  Read the article

• Can't get Broadcom 43142 drivers to work after installation on 5420 Inspiron

  - by beckett

  I'm a complete newbie to ubuntu, I've already installed and reinstalled the Broadcom driver required done a numerous amount of steps on terminal but I can't seem to get wireless working. However, my wired connection seems to work just fine. also I have tried to follow the instructions but get stuck at step number 2 when i get told "No package dpkg is available": 1) Download the file from the link 2) sudo yum install dpkg 3) mkdir BCM43142 4) dpkg-deb -x Downloads/wireless-bcm43142-dkms-6.20.55.19_amd64.deb BCM43142 5) cd BCM43142/usr/src/wireless-bcm43142-oneiric-dkms-6.20.55.19~bdcom0602.0400.1000.0400/src/wl/sys 6) sudo yum install kernel-devel kernel-headers 7) vi wl_linux.c 8) around line 43, remove the line include 9) save the file (:wq) 10) cd ../../.. 11) make Things should work, and you'll have a file called "wl.ko" in the current directory. 12) sudo yum remove broadcom-wl 13) sudo mkdir -p /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 14) sudo cp wl.ko /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 15) sudo depmod -a 16) sudo modprobe wl I really need help :/

  Read the article

• How do I get a Qualcomm Atheros Killer E2200 gigabit ethernet card working on a MSI Z87-GD65?

  - by Travis Allen

  So I literally just built my first computer from scratch and I can't get the network card to work as I've gathered it requires getting some drivers somehow.. Motherboard : MSI Z87-GD65 CPU : Intel Haswell i7 Ubuntu Ver : 12.04 Using the on-board network port Please help I'm about to start crying into my keyboard over this (not really). Any info would be greatly appreciated, also please be very specific as to what I have to do as I have not used Ubuntu very much so talk to me like a child, I won't take offence. Also I've already tried following the instructions here : How do I get a Qualcomm Atheros Killer E2200 gigabit ethernet card working? I don't know if I'm just retarded or am missing something

  Read the article

• How to convert Windows filenames (from a checksums.md5) to *nix notation so I can use it on my shell with md5sum?

  - by Somebody still uses you MS-DOS

  I have some checksums.md5 verification files from an ntfs external drive, but using windows notation: \ instead of /, spaces between file names (not escaped), reserved shell characters (like (, &, ', to name a few). The checksums.md5 has a bunch of checksums and filenames: ;Created by program ;2010 f12f75c1f2d1a658dc32ca6ef9ef3ffc *My Windows & Files (2010)\[bak]\testing.wmv 53445e1a0821b790872e60bd7a166887 *My Windows Files' 2 (2012)\[bak]\testing.wmv 53445e1a0821b790872e60bd7a166887 *My Windows Files ˜nicóde (2012)\[bak]\testing.wmv ;Finished I want to use this checksums.md5 to verify the files that I've copied to my machine: but I'm on a Linux, so I need to convert the names inside checksums.md5 from Windows to Linux to use the md5sum utility from the shell. The first line in my example would become: f12f75c1f2d1a658dc32ca6ef9ef3ffc My\ Windows\ \&\ Files\ \(2010\)/\[bak\]/testing.wmv Is there some application for this (converting a file listing, from windows cmd notation, to linux shell notation) or will I need to create a bash script using sed that just "replaces" what is "wrong" with the filenames?

  Read the article

• Trouble migrating Joomla from Linux to Windows server

  - by Matt

  I'm having some trouble migrating a Joomla website from a Linux server to a Windows server. The database came over fine, Besides that, all I've done is download all the files from the current site, and change configuration.php so the log and tmp directories show "./tmp/" and "./logs/" I keep having an error in the PHP log stating PHP Fatal error: Class 'JTable' not found I've downloaded the site multiple times now, and I'm convinced this is a configuration problem, and not a missing file problem. I've even tried installing a mod for backup on the linux box to try and migrate the site, but sadly the mod had problems installing. The new server is running IIS 7.5 on Windows Web Server. PHP 5.2.14 and MySQL

  Read the article

• slow speed transfering files to a local network device

  - by F. Ariel Jung

  I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

  Read the article

• Physics not synchronizing correctly over the network when using Bullet

  - by Lucas

  I'm trying to implement a client/server physics system using Bullet however I'm having problems getting things to sync up. I've implemented a custom motion state which reads and write the transform from my game objects and it works locally but I've tried two different approaches for networked games: Dynamic objects on the client that are also on the server (eg not random debris and other unimportant stuff) are made kinematic. This works correctly but the objects don't move very smoothly Objects are dynamic on both but after each message from the server that the object has moved I set the linear and angular velocity to the values from the server and call btRigidBody::proceedToTransform with the transform on the server. I also call btCollisionObject::activate(true); to force the object to update. My intent with method 2 was to basically do method 1 but hijacking Bullet to do a poor-man's prediction instead of doing my own to smooth out method 1, but this doesn't seem to work (for reasons that are not 100% clear to me even stepping through Bullet) and the objects sometimes end up in different places. Am I heading in the right direction? Bullet seems to have it's own interpolation code built-in. Can that help me make method 1 work better? Or is my method 2 code not working because I am accidentally stomping that?

  Read the article

• Run Windows Store Apps in a Window on the Desktop in Windows 8?

  - by Kirk

  Is it possible to run Windows Store apps in a window on the desktop in Windows 8? For example, I think the Finance app is awesome, I just don't want it to occupy dedicated space on my screen (either taking the full screen, or snapped to the side). It would be great if I could run it in a window on my desktop. Is this possible? I'm think developers need to view/run/build their apps in a desktop window in order to work productively. Is this the case?

  Read the article

• Which freeware can mount ISOs on Windows 7

  - by Daniel

  WinCDEmu failes (does not work, Windows can not be rebootet anymore) Phantom CD failes (cannot mount from network share) Does an alternative exist?

  Read the article

• Changing internal home network ip address for connected devices

  - by oshirowanen

  I have a few computers at home. For each of the computers, I can see the internal home network ip address on any given device by typing in ifconfig in the terminal. If the device is connected to the home network via ethernet connection or via the built-in wireless connections in laptops, the internal ip address for each of the devices seems to be 192.168.0.X. However, when I connect one of the devices using an external usb modem wireless adapter, which connects to the home network through wireless, when I check the ip address via ifconfig, for some reason it gets assigned 192.168.42.X instead. Why are the ethernet and build in wireless connections getting 192.168.0.X, but the external usb wireless adapter gets 192.168.42.X? Most importantly, is it possible to force it to get an internal ip address of 192.168.0.X?

  Read the article

• How to connect to a wireless network that has a two word name with a space?

  - by grinan

  Ok, I have searched for some time in earnest for an answer to this question. I have a Beagleboard which has Ubuntu 10.10 Minimal install for Arm running on it. With the default install, minimal tools, no GUI, I am unable to connect to my wireless network. The name of my network is "MYNAME NETWORK". Using a text editor to edit /etc/network/interfaces I can not seem to connect at all. As an experiment, I connected to a friends network, which has a one word name "dystek",and was able to connect with Zero issues, and update and install a full GUI for ubuntu Arm. The problem is that I don't want a full blown gui on the beagleboard, just a minimal install of ubuntu with CLI is all I need or want. Is there anyway to connect to my wireless network via editing the /etc/network/interfaces file. Surely there is... I just don't know how. Right now my interfaces file looks like this: auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.1.200 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid BARRETT NETWORK wireless-key 46456xxxxxxxx Any help would be appreciated.

  Read the article

< Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >