Search Results

Search found 15160 results on 607 pages for 'boot disk'.

Page 328/607 | < Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >

• VirtualBox: Can't get Bridged Networking to work (Win7 host)

  - by MikeTheTall

  I'm trying to set up a virtual LAMP server, including sharing files between the guest OS (Ubuntu Server) and the host OS (Windows 7) using samba. I think my problem is that I can't get Bridged (or Host-Only) networking to work in VirtualBox. I can boot the Linux VM just fine with NAT, but then can't access any services on it directly (except after port-forwarding port 80)(my understanding is that port-forwarding works because I'm not running a web server on the host OS, and therefore it can forward traffic to the unused port 80). I don't think that port-forwarding samba traffic (from the host to the guest) will work since I think that the host OS is using those ports. When I turn off NAT and turn bridged networking on I get an error. The VM fails to boot, with a dialog popping up (title: VirtualBox - Error) that says "Failed to open a session for the virtual machine UbuntuServer. Configuration error: Failed to get MAC address (VERR_CFGM_VALUE_NOT_FOUND). I'm hoping that once this is resolved then samba will work ok :) Any advice on this would be great (how to fix it would be wonderful, next steps for troubleshooting would be great, too :) )

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Will these instructions work when turning of journaling on a n ext4 SSD?

  - by snowlord

  I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

  Read the article

• WSS Search fills 10 GB limit on SBS server 2011

  - by Kactus

  I've got a SBS Server 2011 Standard SP1 that isn't very busy. 2 Users local and 2 remote. We have sharepoint that has maybe a dozen small documents at most. I've just started getting the following two error occur Could not allocate space for object 'dbo.MSSBatchHistory'.'IX_MSSBatchHistory' in database 'WSS_Search_SERVER' because the 'PRIMARY' filegroup is full. Create disk space by deleting unneeded files, dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. And CREATE DATABASE or ALTER DATABASE failed because the resulting cumulative database size would exceed your licensed limit of 10240 MB per database. Digging around in SQL manager I see that WSS Search DB file size is 10241MB, the log file is only 147 MB Firstly, why is WSS Search taking up so much space? How can I stop it from doing so, and what can I do now to get things running ok. I know about log file truncating and this isn't the case here since the log is tiny. Any help is appreciated. There is plenty of free space on the disk (791GB free) Thanks Kactus

  Read the article

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• Four disks - RAID 10 or two mirrored pairs?

  - by ewwhite

  I have this discussion with developers quite often. The context is an application running in Linux that has a medium amount of disk I/O. The servers are HP ProLiant DL3x0 G6 with four disks of equal size @ 15k rpm, backed with a P410 controller and 512MB of battery or flash-based cache. There are two schools of thought here, and I wanted some feedback... 1). I'm of the mind that it makes sense to create an array containing all four disks set up in a RAID 10 (1+0) and partition as necessary. This gives the greatest headroom for growth, has the benefit of leveraging the higher spindle count and better fault-tolerance without degradation. 2). The developers think that it's better to have multiple RAID 1 pairs. One for the OS and one for the application data, citing that the spindle separation would reduce resource contention. However, this limits throughput by halving the number of drives and in this case, the OS doesn't really do much other than regular system logging. Additionally, the fact that we have the battery RAID cache and substantial RAM seems to negate the impact of disk latency... What are your thoughts?

  Read the article

• Building a PC, advice on SSD/Hybrid Hard Drives

  - by Jamie Hartnoll

  I am looking at building a new PC, it's mainly for office (graphics heavy) use and programming. Looking for good performance with opening and closing programs and files as well as a fast boot. I plan to have 3 primary hard drives Windows 7 Programs (photoshop etc) Current Files (There'll also be a large storage capacity back up drive, but this will be the Seagate drive I already have.) So, my question is, looking at standard "old fashioned" hard drives and SSD drives, obviously there's a massive price difference. I have been looking at drives like this: http://www.ebuyer.com/268693-corsair-120gb-force-3-ssd-cssd-f120gb3-bk-cssd-f120gb3-bk and this: http://www.ebuyer.com/321969-momentus-xt-750gb-sata-2-5in-7200rpm-hybrid-8gb-ssd-in-st750lx003 Having no experience of using either I don't know what's the most efficient thing to go for. Clearly the SSD will have better performance, but: If, for example, I had an SSD for Windows (say about 100gB), that would clearly give me the boot speed I want, then I guess my real questions are: If I were to buy one more SSD, would it give the greatest improvement on standard performance if used to store programs, or currently used files? Given that the OS is on an SSD, should I not bother with the 3 drives and instead, partition that Hybrid drive to store programs and currently used files on it? Obviously, option two is cheaper and option one could cause me storage issues, but that's when I can dump files I am not currently using onto another drive. Any, I am open to suggestions... so what do you suggest?!

  Read the article

• Program for remove exact duplicate files while caching search results

  - by John Thomas

  We need a Windows 7 program to remove/check the duplicates but our situation is somewhat different than the standard one for which there are enough programs. We have a fairly large static archive (collection) of photos spread on several disks. Let's call them Disk A..M. We have also some disks (let's call them Disk 1..9) which contain some duplicates which are to be found on disks A..M. We want to add to our collection new disks (N, O, P... aso.) which will contain the photos from disks 1..9 but, of course, we don't want to have any photos two (or more) times. Of course, theoretically, the task can be solved with a regular file duplicate remover but the time needed will be very big. Ideally, AFAIS now, the real solution would be a program which will scan the disks A..M, store the file sizes/hashes of the photos in an indexed database/file(s) and will check the new disks (1..9) against this database. However I have hard time to find such a program (if exists). Other things to note: we consider that the Disks A..M (the collection) doesn't have any duplicates on them the file names might be changed we aren't interested in approximated (fuzzy) comparison which can be found in some photo comparing programs. We hunt for exact duplicate files. we aren't afraid of command line. :-) we need to work on Win7/XP we prefer (of course) to be freeware TIA for any suggestions, John Th.

  Read the article

• Setting up Windows network on Xen

  - by samyboy

  I'm trying to install a Windows XP server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny currently hosting around 10 Linux virtual servers. Windows tells me I have a "limited connection". It can't get any DHCP response, nor access other hosts in the network Here is the Xen's client config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '1024' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' Server config (/etc/xen/xend-config.sxp) (network-script network-bridge) (network-script network-dummy) (vif-script vif-bridge) (dom0-min-mem 512) (dom0-cpus 0) (vnc-listen '0.0.0.0') Since I use Debian I had to create a link like this: /etc/xen/qemu-ifup - /etc/xen/scripts/qemu-ifup What did I do wrong? Please tell me if you want some more info (logs, etc)

  Read the article

• How to check DVD integrity at max read speed of DVD writer

  - by ashishsony

  I need to check the integrity of burned DVDs so that I can be sure about my backed-up data. I use DL-DVDs to take the backup. Earlier I used VSO Inspector software for the same but the day I switched to DL-DVDs the VSO Inspector gives me errors upon checking. I think the errors are because the switching of layer writing involves some dummy data somewhere. Secondly, it's damned slow for checking. I believe if there is a utility that can read all files (not the disk surface) and report if some files are unreadable would do the job. But it should be quick! Nobody wants to sit for disk checking for 3-4 hours after a quick 30 min data burn! I am looking for such a utility on Windows or Linux. Even scripts (python, etc) will do. I just want to be assured that the data is safe. Can someone help me in this? Thanks.

  Read the article

• Windows XP only loads in VGA mode, and crashes when raising resolution

  - by Harel

  My kid's computer (Windows XP, SP3) started to (what appears to be) crash on boot. It will only boot in Safe or VGA mode, and if I try to raise the resolution from 640x480 it just reboots itself, and a error appears in the Event Log. When it loads up not in VGA mode, the monitor shuts off just after the windows logo is shown. It seems like windows is actually running but I can't see anything on screen (monitor is off for lack of signal). Nothing was installed recently that I know of, short of the usual windows updates. Thanks, Harel Below is the event log error: Event Type: Error Event Source: System Error Event Category: (102) Event ID: 1003 Date: 15/04/2012 Time: 16:27:11 User: N/A Computer: ----- Description: Error code 1000008e, parameter1 c0000005, parameter2 f745b0bf, parameter3 ede24f98, parameter4 00000000. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 31 30 30 30 30 30 38 1000008 0020: 65 20 20 50 61 72 61 6d e Param 0028: 65 74 65 72 73 20 63 30 eters c0 0030: 30 30 30 30 30 35 2c 20 000005, 0038: 66 37 34 35 62 30 62 66 f745b0bf 0040: 2c 20 65 64 65 32 34 66 , ede24f 0048: 39 38 2c 20 30 30 30 30 98, 0000 0050: 30 30 30 30 0000

  Read the article

• XP Pro freezes on welcome screen

  - by Peter B

  I have a problem that sounds much the same as http://superuser.com/questions/83101/how-to-diagnose-a-freeze-on-startup-in-windows-xp About every 2nd or 3rd boot, XP-Pro freezes on the Welcome page (the one showing the user name icons). The mouse moves the cursor OK, but clicking on an icon does nothing, and neither does any keystroke. If you press too many keys there is a beep and after that the mouse won't move the cursor anymore. The work-around is always to reboot into Safe mode and request a CHKDSK /R After this, the next boot is fine. There are no related entries in the Event log when the problem occurs. The only two entries are: "Microsoft (R) Windows (R) 5.01. 2600 Service Pack 3 Multiprocessor Free." "The Event log service was started." Update 1: Many thanks for that but I found no problems with any diagnostics I have run. But, I have managed to locate, and code round, the source of the problem - which is with whatever processing goes on behind the XP Welcome (as opposed to "classic") login screen. Unfortunately, having classic login means you don't get the useful Fast User Switching (FUS) login/switch mode. So, to retain this, my fix is: Add a Windows shutdown script (using gpedit.msc) to force "classic" mode for the first logon after next XP startup, by running: reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /v LogonType /t REG_DWORD /d 0 /f Add a Scheduled Task to run at User Logon that enables Welcome screen (and hence FUS) by running the same command with 1 instead of 0 after the /d flag. The task is run as a privileged user (who can run "reg add").

  Read the article

• Installing and running a guest OS on KVM-qemu with only serial console access

  - by nixnotwin

  I am trying to installing a bsd distro with virt-installer. With a Linux distro I used this: virt-install -n debian -r 1024 --vcpus=1 --accelerate -v --disk /var/kvm/installation-disks/debian.img,size=6--nographics --network=bridge:br0,model=ne2k_pci,mac=52:54:00:66:68:09 -l http://ftp.de.debian.org/debian/dists/squeeze/main/installer-amd64/current/images/ -x console=ttyS0,115200 This loads the installer directly from the online mirror. With Fedora I used this mirror: http://www.nic.funet.fi/pub/mirrors/fedora.redhat.com/pub/fedora/linux/releases/16/Fedora/x86_64/os/ Are there such mirrors for freebsd or openbsd? The reason I want direct installable ftp/http mirrors is because I can access my physical server only via ssh, and it doesn't have a X server or a window manager to give me a VNC GUI. When I tried installing centos 6 with an online mirror I was able to finish the installation via serial console, but after I rebooted it, the serial console never worked for me. I tried everything possible---editing menu.lst, inttab and securtty files. Fedora 16 booted fine from serial console, but got stuck when it loaded anaconda installer. I tried editing freebsd iso installation media by adding serial console option to boot option. And installation was successful. But couldn't boot into it becuase it wasn't giving console acess. I couldn't edit any files as ufs partition cannot be loaded with write access on my Ubuntu server 10.04. Only debian squeeze worked well, it worked for me even without editing a single configuration file. I want to have CLI versions of fedora/centos and freebsd/openbsd. But, looks like there isn't any hope for me to have them, as I have to depend on a serial console to do everything.

  Read the article

• Problems with Windows 7 restore

  - by Chris Lively

  My WD raptor 150 failed with a nice clicking noise. So, I picked up a velociraptor 300 and popped it in. I had windows set to do a full system backup nightly, so I figured the recovery ought to go easily. Well, it isn't. It is currently stuck on a screen that says: "Windows is restoring your computer from the system image. This might take from a few minutes to a few hours" Below that is a rather large progress meter with maybe the first block filled in. Below that is a message that says "Restoring disk (C:)..." It's been that way for over an hour. The first time around, I gave up after 2 hours. I then booted into the system recovery options and went to a command prompt and ran a chkdsk on the new drive. It showed several file inconsistencies and not much else. I ran a chkdsk /f on it and tried again... Which is where I'm at now. I can't see that the restore process should take this long before. Any ideas? UPDATE After 10 hours, it's still on "Restoring disk (C:)" and the progress meter is at roughly 5%. I'm guessing at the 5% as there isn't an actual number or anything else that I can look at showing what it's actually doing. The backup contains roughly 120GB of data. How slow is windows restore?

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• Scheduling Automatic Backups for Virtual Private Web Server running CENTOS 6.3 and WHM

  - by Oliver Farrell

  I'm pretty new to administering my own VPS - but thus far am finding it quite a compelling experience. There's something quite refreshing about having complete control over everything it does. One thing that I would like to look at is a suitable backup solution (a few times a day). My current setup is as follows: I'm running a CENTOS 6.3 VPS with a single 25GB hard drive solely for the purpose of hosting websites. I'm using WHM & cPanel for administering them. I now plan on adding an additional hard disk and hooking it up to my VPS. What I'm not sure about is how I get the two disks talking and get the backup process going. I'm not a seasons SSH-er so don't really know where to start. I'm hosting with Serverlove (one of the best hosting providers I've used) and am provided with a number of unique identifiers for each hard disk so I imagine these may play a part in linking them together. I appreciate that this is a little vague (I'm clutching at straws) but any assistance is very much appreciated.

  Read the article

• Microsoft SQL Server Management Studio causing system freeze

  - by CRoshanLG

  I'm experiencing very slow response from MSSMS and it causes other applications to slow down. Specially Skype crashes after few seconds from opening MSSMS, showing an error called "Disk I/O Error". I'm regularly using few applications (Sublime text, MS Word, Firefox, Outlook, Skype and one or two other apps) simultaneously. The system works fine when MSSMS is not in use! But as soon as MSSMS is opened, all the apps start to freeze (MSSMS also responds very slow). This problem has been there for about a week now (I haven't installed any apps or haven't made any changes to the system during that time). -- System Specifications -- Processor: Core i3 (3.1 GHz) RAM: 4 GB OS: Windows 7 Professional (64 bit) Free space in C drive: ~ 100 GB MS SQL Server 2008 R2 Microsoft SQL Server Management Studio version - 10.50.1600.1 I've tried to find a reason for this but there are no helpful information in the web! There are some solutions suggested (in forums and in Skype Support pages) for the Skypes' "Disk I/O Error", all of which I tried but does not solve the problem. Has anyone faced the same senario? (and hopefully) knows a solution? Systems Log I don't have much knowledge in interpreting the System Log, but I think the Critical and Warnings are not helpful. But there are lots of Error logs which might be useful. In source Kernal-General there are few similar errors saying "An I/O operation initiated by the Registry failed unrecoverably.The Registry could not flush hive (file): <some file>" In source atapi also there are few similar errors -- "The driver detected a controller error on \Device\Ide\IdePort0." (all errors has occurred in 'IdePort0') In Application Error, there are several errors logged, and following is the latest one. Both the Errors which has occurred today is similar (to this one). As it is from Ssms.exe, I guess this is relevant to the cause of problem. But as I said above I can't understand what it means!

  Read the article

• Dell Studio 1555 not starting up

  - by Abhishek

  This is a 3-year-old laptop. I never had a big problem with it until now. I updated Kubuntu the night before yesterday. And Firefox got updated to version 18 and a few other related packages got updated. Then I shut down the laptop and restarted it, but it failed to start. I could hear the fan and the hard disk and the optical disk drive initialize. And the power button also lighted up. But there was no video - no POST or BIOS menu. I even opened the laptop up to the point when only the motherboard was the only thing attached to the base cover. I took it to the technician this evening. He checked it casually, and said that it might be a motherboard problem and will cost quite a bit to fix. Though he was not sure and said that he will give me a call after confirming the problem. Has anyone else had the same problem? What was it and what was the fix?

  Read the article

• Grub hangs at "Starting up ..." when USB flash card reader is plugged in (on Ubuntu Hardy)

  - by Laurence Gonsalves

  I have a PC with Ubuntu Hardy installed. The machine boots fine unless my USB flash card reader (one of those N-in-1 readers by MediaGear) is plugged in at startup. If the reader is plugged in, the boot process proceeds as normal until it gets to the screen that says "Starting up ...". At that point it just hangs forever. To work around this I currently leave the reader unplugged when booting, and then plug it back in after I see that Ubuntu is actually starting. This is annoying though, especially when I reboot the machine (typically for updates), forget to unplug the reader, and walk away only to come back hours later to find the machine hung. My guess is that the presence of the reader is confusing Grub about where to find the kernel. The weird thing is that Grub is on the same drive as the kernel I want it to boot so clearly the drive is still readable even when the flash card reader is plugged in. Is there some way I can tell Grub to never go looking on the flash card reader?

  Read the article

• Coffee spilled inside computer, damaged hard drive

  - by Harpreet

  Today coffee spilled over my table, and some of it (very less) reached the PC case placed under the table. I think little bit of it got inside the PC case through the front. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help!! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Drobo-like linux file server - how do I do it?

  - by John Hunt

  I've been pondering for a long time about how I can set up a server which operates much like the Drobo storage thing. The reasons I don't actually want a drobo is because I've heard scare stories, plus I'd like to do this on the cheap. So ideally I'm looking for something like lvm so I can create a logical volume that spans many hard disks of varying sizes... obviously that only offers redundancy if I put the LV on a raid array (as far as I know..) I have however been reading about technologies such as Microsoft's drive extender which duplicates files at the filesystem level and makes sure that the mirrored files are on a different phyiscal disk.. does anyone know or recommend a filesystem or method like this as it'll hopefully make much better use of the space available than raid ever could. Performance isn't an issue, I'd just really like to make the most of the hard disks I have lying around whilst having a bit of redundancy incase a disk dies. I understand full well that this is no replacement for a backup, but I'll only be storing files of medium importance and using the nas itself as a backup of my main pc and other systems. Thanks in advance! I'm hoping zfs or btrfs or something can do something clever for me :)

  Read the article

• Install a KVM guest with LVM partitioning on an LVM partitioned host using virt-install fails, volume group already exists

  - by Rilik84

  our setup consists of a ubuntu 10.04 kvm host server with LVM, on top of which we install the ubuntu 10.04 virtual machines via virt-install and preseed. Each VM has a dedicated logical volume which we pass to virt-install via the "--disk path=/dev/sysvg/vm-name" parameter. The virtual machines themselves are using LVM as well. Virt-install seems to have a few issues with this setup. Say we want to install two virtual machines in parallel. The first vm installs correctly while the second halts during the partitioning, complaining with this error: "volume group name already in use". I tried removing the logical volumes, recreated them, rebooted the kvm host to clear any leftovers but the issue perists. The preseed is telling the vms to create a volume group named "sysvg", which is the same name used by the volume group of the kvm host. Considering this I did another test: I got rid of the preseed part taking care of the partitioning/lvm creation and started the creation of two vms in parallel. If, when prompted, I instruct the vms' installer to do a guided partitioning of the disk with LVM, it will still fail giving this different error on both the vms: Physical Volume /dev/sda5 is already in volume group sysvg. As I wrote, sysvg is the volume group used by the KVM host. So I thought the name clashing was the issue. By removing the preseed part I skipped the volume group naming. I can't understand how the virtual machines would be aware of the presence of that volume group since they're supposed to be isolated from it, especially after I removed and recreated the logical volumes dedicated to them. That detail should not be exposed at all to them! Thanks for the help. I'm clueless.

  Read the article

• Is USB supported in safe mode on XP?

  - by Hugh Allen

  According Microsoft, "Universal Serial Bus Devices Do Not Work in Safe Mode" under XP. However, in my testing this is incorrect. USB keyboards, mice and flash drives seem to work fine in safe mode (I made sure the BIOS was not providing support). This makes sense because a failure of a standard input device would be, in Microsoft parlance, a "bad user experience". So, Is USB supported in safe mode on XP? If your answer is no (agreeing with Microsoft), please provide a test case, preferably in a virtual machine, where a standard HID keyboard or mouse fails. Please state hardware / BIOS / OS configuration. Note that you will need a PS/2 keyboard attached in addition to your USB device(s) in order to use the boot menu. Virtual machine software usually emulates a PS/2 keyboard. Alternatively, you could add the /safeboot switch to boot.ini. If your answer is yes, please provide a link to some supporting documentation (either from Microsoft or someone authoritative). Your answer might be "devices X, Y and Z are supported but nothing else", in which case also give a link.

  Read the article

• systemd: enabling cherokee service as a `unit file`

  - by Calvin Cheng

  So I am learning how to use systemd to initialize my services automatically on server reboot. So of course, I first make sure I have systemd and some optional systemd related packages installed. pacman -S systemd initscripts-systemd Installation seems to go well and checking, I can see that systemd and its dependency libsystemd are installed. And the optional package initscripts-systemd is also installed:- [root@li280-195 ~]# pacman -Ss systemd extra/libsystemd 44-5 [installed] systemd client libraries extra/systemd 44-5 [installed] system and service manager extra/systemd-sysvcompat 2-2 sysvinit compat symlinks for systemd community/initscripts-systemd 20120412-1 [installed] Arch specific systemd initialization/bootup scripts for systemd community/systemd-arch-units 20120412-2 Arch specific Systemd unit files Next, I ensure that systemd is loaded up when my server reboots, via grub in grub's /boot/grub/menu.lst file like this:- kernel /boot/vmlinuz root=/dev/xvda ro init=/bin/systemd Rebooting my server to check, all loads up well and I can check that systemd is operational via:- systemctl list-unit-files However, I don't see my cherokee initialization script (which is simply created at /etc/rc.d/cherokee when I installed cherokee earlier via pacman -S cherokee) being listed as one of my unit files. So the question is, how do I do that? How do I put my cherokee initialization script under systemd's control?

  Read the article

< Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >