Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 328/1221 | < Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >

  • router only assigns small number of IPs

    - by Liam Coates
    Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

    Read the article

  • Network card very slow, only on Windows

    - by J Penguin
    This only happens to 1 of my machine, and only when booting into Windows 7. No matter what network card I put in, Windows would default its mode to 10Mbps full duplex. Transfer speed is approximately 1 MB/s. If I set it to 100Mbps, the transfer drops to 100-200K/s. If I set it to 1000Mbps, the connection is lost completely. I've tried swapping in different cards, both PCI-E and PCI. I'v etried update the windows, I've tried reinstalling the drivers... On this very same machine, if I boot into Fedora, it can use the card at its full capacity 1000Mbps transfering 80+ MB/s And all the cards work just fine when plugging into other machines on the same network. I'm very curious. What could be the reason for this? The only different software that this machine has is virtual box with a VPN emulator, but disabling that VPN doesn't seem to do anything. I would like to get this fixed, hopefully, without reinstalling windows _< Will that be possible?

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

    - by Dr Rocket Mr Socket
    As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

    Read the article

  • Is browser based wireless authentication secure?

    - by johnnyb10
    Our wireless network previously used a preshared WPA/WPA2 key for guest access, which allows them access to the Internet. (Our employee access uses 802.1x authentication). We just had a wireless consultant come in to fix various wireless issues we had; one of the things he wound up doing was changing our guest access to HTML-based instead of the preshared key. So now that guest SSID is open (instead of using WPA) and users are presented with a browser-based login screen before they can get on the Internet. My question is: Is this an acceptable method from a security standpoint? I would assume that having an open network is necessarily a bad idea, but the consultant said that the traffic is still using PEAP, so it's secure. I didn't get a chance to question him further on this because we ran late and a bunch of other things came up. Please let me know what you think about the advantages/disadvantages of using HTML-based wireless authentication as opposed to using a preshared WPA key. Thanks...

    Read the article

  • windows server 2008 r2 remote desktop issue with roaming clients

    - by Patrick D'Haese
    I have the following situation : a Dell windows server 2008 R2 computer, with remote desktop services installed. I have installed a java application making use of a PostgreSql database, and made this application available for clients using RDP. Clients are standard Win XP pc's and Psion Neo handheld devices running Windows CE 5 Pro. The application works fine for clients on standard XP pc's connected directly via cat 5E Ethernet cable to a Dell Powerconnect 2816 switch. The Psion Neo clients connect wireless to the network via Motorola AP6532 access points. These access points are connected via a POE adapter to the same switch as the XP pc's. The Psion devices can connect without any problem and very quickly to the server and to the application using RDP. So far, so good. When the Psion devices move around in the warehouse, and they roam from one access point to the other, the RDP session on the client freezes for approx 1 minute, and then it automatically resumes the session. This freezing is very annoying for the users. Can anyone help in solving this issue? Update (August 9) : After re-installing the access points we have a working situation, but only when connecting to the RDP host : * via a Win Xp SP3 laptop * via a Symbol MC9190 Win CE 6 mobile device When roaming we notice a small hick-up less then 1 second, what is very acceptable. With the Psion NEO it's still not working, when roaming the screen freezes from 2 to 30 seconds. The RDP client on the win xp sp3 laptop and the symbol mc9190 is version 6.0. The RDP client on the neo is version 5.2. I have changed the security layer on the RDP host to RDP security layer (based on forums on the internet), because older RDP clients seem to have issues with the RDP 7.1 protocol on the Win server 2088 R2. Psion adviced us to do some network logging activity on the different devices. We made this logging via wireshark, and based on this the conclusion of Psion is that the server fails in handling tcp-requests. Can anyone give me a second opinion by analysing the wireshark loggings. Thanks in advance. Regards Patrick

    Read the article

  • Adding third disk as a single disk in a server with an existing RAID1

    - by slowhandsolo
    I've got a ProLiant DL360 G5 server (Fedora 13) with two SAS disks in a hardware RAID 1, working fine. Now I hot plugged another SAS disk. I'd like to configure this new hard disk out of my RAID, as a single non-RAID disk (ex. /dev/sdb). Even after rebooting the server, I can't see the new disk with "fdisk -l". It displays only my hardware RAID, but not the new disk. [root@myserver]# fdisk -l Disco /dev/cciss/c0d0: 300.0 GB, 299966445568 bytes Disposit. Inicio Comienzo Fin Bloques Id Sistema /dev/cciss/c0d0p1 * 1 126 512000 83 Linux /dev/cciss/c0d0p2 126 71798 292422656 8e Linux LVM Disco /dev/dm-0: 234.9 GB, 234881024000 bytes Disco /dev/dm-1: 10.5 GB, 10536091648 bytes Disco /dev/dm-2: 21.0 GB, 20971520000 bytes Disco /dev/dm-3: 31.5 GB, 31474057216 bytes Disco /dev/dm-4: 1577 MB, 1577058304 bytes However, I can see the new disk using the HP Array Configuration Utility CLI for Linux "hpacucli": [root@myserver]# hpacucli => controller slot=0 physicaldrive all show status physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 300 GB): OK physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 300 GB): OK physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 300 GB): OK => controller slot=0 pd all show detail Smart Array P400i in Slot 0 (Embedded) array A physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 **unassigned** physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: **Unassigned Drive** As you can see, I've got two SAS disks in a RAID 1 and the new disk as "unassigned". Is there any way to work with the new disk as another non-RAID single disk? If relevant, I want to create a new partition in my new disk, format it with mkfs and mount it, but as I can't see it with fdisk, I don't know how to do it. Thanks!

    Read the article

  • Cannot access server shares over VPN

    - by DuncanDavies
    I've set up a single hosted server to use as a development environment for a web-based application. The web app is served up fine on port 80, however I'm struggling to get my VPN to behave how I'd expect so the developers don't have the access they require. The VPN connects fine and I can access the back-end database (SQL Server) which resides on the server with the client tools from the laptops. However they cannot access any shared folders. The server's local IP address is 10.x.x.x, and I've assigned a static IP address pool to RRAS (of 192.168.100.1 - 20). The clients pick up a valid IP Address (i.e. 192.168.100.9) when they connect. There is no name resolution setup, DNS or WINS. When connected via VPN the clients can ping the server (192.168.100.1) by IP Address, but cannot map a drive to a shared folder (net use * \\192.168.100.1\xxxxx) - I get 'System error 53 has occurred. The network path was not found.' I don't understand why I can ping by the ip, but not map by it. Some details: Server OS is Windows 2008 (Datacenter) VPN is SSTP using RRAS Clients are all Windows 7 I've tried temporarily disabling the firewalls So, why can we not access the file system when everything else (ping, RDP, SQL Server clients tools) works? Thanks for your help Duncan

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • OpenVPN on Tomato and Vista - can't see my network

    - by Ian
    I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

    Read the article

  • Firebox 1250e Core Failing?

    - by Noah
    We have 2 Firebox 1250e Core firewall boxes in our production environment, serving as an active and passive mode. A few months back, the active box was flashing a warning light, so our consultant removed it, and plugged it in to a test network. Everything appeared to be working fine, so he reloaded it into the production environment, and we didn't see any other issues. Fast forward to last week, and out network was constantly dropping connections over RDC, timing out, and performing as if there was a traffic issue. I turned off the production box and everything began to work fine immediately. At this point though, I'm not sure how to proceed. Should the box be completely replaced? Is there any recommended testing we could do to determine if there is a failure of some type with this device? Should we try upgrading the software on it? I know the environment isn't the issue, since the passive box (which is now the active one) is working fine. We'd like to have 2 in production though for safety failover purposes. I am not a network admin, but am hoping someone here might be able to provide some guidance.

    Read the article

  • What software do you use to detect an internect connection drop?

    - by Darryl Hein
    I'm looking for a piece of software to detect drops in my internet connection and log those drops. OS doesn't really matter since I have pretty much everything running here, although something on OSX would be nice. I also don't really care how it determines that connection has been dropped, but I think that there must be something better than a ping or at least a combination of a ping and something else.

    Read the article

  • Creating a secure multicast tunnel with socat

    - by ams
    How we can create secure multicast tunnels ith socat? Assume that we have a list of IP address, CIDR network addresses that we want to create secure tunnel to them. I found this: socat STDIO UDP4-DATAGRAM:224.1.0.1:6666,range=192.168.10.0/24 but I want a secure tunnel and different adds with net addrs I want to create script that give the IPs and net addresses and creates a secure tunnel ./myscript IP1 NetAdd1 IP2 NetAdd2 .... How can I send these parameters to socat? Does socat multicast have any limits?

    Read the article

  • Vista laptop 1 connects to network but Vista laptop 2 doesn't

    - by Jaips
    (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

    Read the article

  • Network topology question

    - by Asbie
    We currently have three networks, X.X.163.1, X.X.93.1 and 192.168.1.1. Today's setup is like this: http://i.imgur.com/tkKWy.jpg We now have PPT VPN from internet to the X.X.163.1-network, but really need to access the files from the File Server through VPN. I am also aware that this setup is not optimal. So please, any advices on how to redesign our network? Rack servers are mostly web and db servers, with only public IP addresses.

    Read the article

  • Does an unmanaged 4/8-port GBit Ethernet switch with a GBIC port exist?

    - by Aaron Digulla
    I'm looking for a simple unmanaged switch with 4-8 GBit Ethernet ports and a fiber port (either as a GBIC slot or pre-installed with a 1000BASE-SX port). Does something like that exist? [EDIT] I want to connect to places in my home without drilling large holes though the floors. Therefore, I'm looking for a cheap way to connect two GBit switches via fiber. I tried with a media converter (GBit <- multimode fiber) but that costs about 50% throughput. So I was hoping that there is a cheap, small GBit switch which has a GBIC slot). All I found so far are very expensive managed switches with 12 or 24 ports for industry use.

    Read the article

  • How can I unregister a service with dns-sd?

    - by Roman
    I am trying to use "dns-sd" command line tool on my Windows 7 machine. I can already do something. For example I can register a service using "dns-sd -R ...". I also can browser (see) registered services using "dns-sd -B ...". What I still miss, is how to unregister a service. At the moment when I type "dns-sd -R ..." the dns-sd does not return me to the command prompt. To return to the command prompt I need to press Ctrl-C. And the service stays registered till I press Ctrl-C. What I want is to run "dns-sd -R ..." in the background regime and then I would like to have a possibility to unregister a service from the command line. One more thing which I do not understand yet is what "to look up a service" means. In my picture it should be sufficient to register a service, to see it and then to unregister it. But apparently I need to look up a service. What does it mean and why I need to do it?

    Read the article

  • Packet loss with all adapters on one PC only on the LAN

    - by Enigmativity
    I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

    Read the article

  • Router's ssid changes from infrastructure to ad-hoc

    - by waldo
    For a period of time the router's ssid is shown (on various computers) as a normal infrastructure network - computers connect fine and everything works however after a few minutes / hours all computers see the same ssid as an ad-hoc network (not infrastructure). At this point a computer that was already connected continues to work - a computer that isn't cannot connect. Rebooting the router temporarily restores the visibility of the correct infrastructure ssid. Is something interfering? Connecting computers: macbook (2009), iphone 3g, windows vista desktop, windows xp desktop. Details: - D-Link DSL-2740B router set to WPA2-PSK (Personal) - Enable Wireless : Yes - Wireless Network Name (SSID) : ###### - Country : Australia - Wireless Channel : 1 - 802.11 Mode : Mixed 802.11n, 802.11g and 802.11b - Channel Width : Auto 20/40 MHz - Transmission Rate : Best (automatic) - Hide Wireless Network : No - Group Key Update Interval : 0 (seconds)

    Read the article

< Previous Page | 324 325 326 327 328 329 330 331 332 333 334 335  | Next Page >