Search Results

Search found 11365 results on 455 pages for 'authorization basic'.

Page 332/455 | < Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >

• How to pipe internet radio into a tuner?

  - by JW

  UPDATE: Thanks everyone for the ideas! This was an area I knew very little about but now I can talk with a little more expertise about it. Much appreciated! Visited my dad this weekend and he wants to pipe some internet radio he's found down to a tuner on quite a distance away in the house. He uses computers for only very basic things: e-mail, getting the Post crossword, checking Yahoo!, checking recipes, etc. There's currently one computer in the house (no router). My initial suggestion (without any research whatsoever) was to get a wireless router and a netbook for downstairs near the tuner, but he initially wasn't too keen about having another computer down there. Anyway, is there any computer hardware that could magically pipe the audio output from the computer down to one set of (RCA) audio inputs on the tuner? Wireless isn't necessary but it probably would be easier. Anyway, thanks for your suggestions! UPDATE Thanks everyone! Voted up all of your suggestions now that I have 15 rep. Much appreciated.

  Read the article

• Troubleshoot dropped wireless connections

  - by Jack

  I was recently hired in the IT department of a small company (~180 users) and one of the issues that people have been complaining about is having their wi-fi connections drop during meetings. The company is using an HP ProCurve Wireless LAN with 10 APs and a controller unit located in the server room. I don't have any experience troubleshooting WLAN in a multi-AP environment, so I'm trying to at least gather information using free or cheap tools. I did a basic site survey using the free version of Ekahau HeatMapper and discovered the following in one of the conference rooms that has been a problem. The program picked up three access points (plus a bunch of others with much lower signals that were out of range): AP 1: SSID: "Unknown SSID" - Signal strength: -48 dBm - -40 dBm. Channel: 2 AP 2: SSID "CompanyMain" - Signal strength: -35 dBm or greater. Channel: 2. Security: WEP (This is the main SSID for the company's WLAN.) AP 3: SSID: "CompanyGuest" - Signal strength: -40 dBm - -35 dBm. Channel: 2. Security: WPA2 (This SSID is the company's "guest" WLAN, which was setup to allow Internet access, but prevent network access.) Is there anything that you see that is clearly a problem from the above? I'm assuming that the unknown SSID might be a big problem, and that it is an AP from a neighboring office that is causing interference. Does that seem likely? Also, regarding channel, should we try changing the channels of our APs to avoid interference with that unknown SSID? (Since everything seems to be on Channel 2?) Should our APs be on different channels? In other words, should the CompanyMain and CompanyGuest APs be on different channels? Finally, any recommendations for free/cheap tools to help me figure this out, and/or a good methodology to follow? Thanks in advance for any help. Jack

  Read the article

• Apache showing 500 error during Active Directory LDAP authentication

  - by Tyllyn

  I have Apache (on Windows Server) set up to authenticate one directory through Active Directory. Config settings are as follows: <LocationMatch "/trac/[^/]+/login"> Order deny,allow Allow from all AuthBasicProvider ldap AuthzLDAPAuthoritative Off AuthLDAPURL ldap://<ip-redacted>:3268/cn=Users,OU=MyBusiness,DC=<dc-redacted>,DC=local?sAMAccountName?sub?(objectClass=*) AuthLDAPBindDN trac@<dc-redacted>.local AuthLDAPBindPassword "<password-redacted>" AuthType Basic AuthName "Protected" require valid-user </LocationMatch> Watching, Wireshark, I see the following get sent through when I visit the page: To the AD server: bindRequest(1) "trac@<dc-redacted>.local" simple And from the AD server: bindResponse(1) success I'm assuming this means that the auth was successful... but Apache doesn't think so. It returns a 500 server to me. Apache logs show the following: [Thu Nov 18 16:21:12 2010] [debug] mod_authnz_ldap.c(379): [client 192.168.x.x] [7352] auth_ldap authenticate: using URL ldap://<ip-redacted>:3268/cn=Users,OU=MyBusiness,DC=<dc-redacted>,DC=local?sAMAccountName?sub?(objectClass=*), referer: http://192.168.x.x/trac/Trac/login [Thu Nov 18 16:21:12 2010] [info] [client 192.168.x.x] [7352] auth_ldap authenticate: user authentication failed; URI /trac/Trac/login [ldap_search_ext_s() for user failed][Filter Error], referer: http://192.168.x.x/trac/Trac/login Now, that log file shows a failed auth for a blank user. I am confused. Any idea what I am doing wrong... and how I can get the Apache authentication working? :) Thanks!

  Read the article

• SQL Full-Text indexing not populating

  - by Sam

  We installed a clustered SQL 2005 installation on windows 2008 and reattached our san drives from another machine and restored to do a migration to new hardware. There have been a few minor issues, but this one has me stuck. Trying to populate Full-Text indexes is not working. I create a basic table with some simple text in a new database and get the same results as old indexes. 2010-09-27 10:30:46.85 spid19s Informational: Full-text Full population initialized for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'). Population sub-tasks: 1. 2010-09-27 10:31:15.36 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001DF. Attempt will be made to reindex it. 2010-09-27 10:31:15.37 spid19s The component 'MSFTE.DLL' reported error while indexing. Component path 'D:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\Binn\MSFTE.DLL'. 2010-09-27 10:31:15.37 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001E0. Attempt will be made to reindex it. The rebuild/repopulate procedure finishes, but I get zero rows in the index. The .dll in the message is present and the service accounts have access to this. My FTData also has data in it, so it seems there wouldn't be permission issue on this folder. Application throws this error: “PHP Warning: mssql_query() [function.mssql-query]: message: Full-text catalog 'ikm_PageIndex_FText' is in an unusable state. Drop and re-create this full-text catalog. (severity 16) in E:\Inetpub\knowledgebase_insidemesa\lib\database\mssql.php on line 154” A microsoft discussion is the only post I found which had claimed to fix this - said it was registry related, but then didn't post the fix.

  Read the article

• SQUID proxy - open FTP (and other ports)

  - by gaffcz

  elpeHow can I open other ports than HTTP and HTTPS using SQUID proxy? I have last version of squid running on Fedora 10 but I'm not able to open FTP port. part of my squid.conf: acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 acl ftp proto FTP acl ftp_port port 21 always_direct allow FTP acl SSL_ports port 443 20 21 22 acl Safe_ports port 20 # ftp acl Safe_ports port 21 # ftp acl Safe_ports port 22 # sftp acl Safe_ports port 80 # http acl Safe_ports port 280 # http-mgmt acl Safe_ports port 443 # https acl Safe_ports port 1025-65535 # uregistred ports acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager # USER privilegies (encoded in file passwd) auth_param basic program /usr/lib/squid/ncsa_auth /etc/squid/passwd acl AUTHUSERS proxy_auth REQUIRED # BLACKLIST (in file denied.conf) acl denied_domains dstdomain "/etc/squid/DNDdomains.conf" acl denied_regex url_regex "/etc/squid/DNDregex.conf" http_access deny denied_regex http_access deny denied_domains http_access allow AUTHUSERS http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow ftp_port CONNECT http_access allow ftp http_access allow localhost http_access deny all #http_reply_access allow all #http_access allow all http_port 3128 hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid 10000 16 256 coredump_dir /var/spool/squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 I've tried to add: acl ftp proto FTP / acl ftp_port port 21 http_access allow ftp add/remove ports 20,21 from SSL_PORTS list set the iptables But nothing helped. It is even possible to use a new version of squid for FTP transfer?

  Read the article

• php_ibm_db2.dll on IIS 7.5 using PHP 5.3 error message

  - by grmbl

  I'm trying to use ibm_db2 extension to access iSeries DB2 database. This is the testcode (taken from here) <?php $database = 'ALI452BFAL'; //library $user = 'STN452'; $password = '**********'; $hostname = 'myserverip'; $port = 50000; $conn_string = "DRIVER={IBM DB2 ODBC DRIVER};DATABASE=$database;" . "HOSTNAME=$hostname;PORT=$port;PROTOCOL=TCPIP;UID=$user;PWD=$password;"; $conn = db2_connect($conn_string, '', ''); if ($conn) { print "ok"; db2_close($conn); } else { echo db2_conn_error() . '<br>' . db2_conn_errormsg(); } ?> I have installed a very basic package containing the db2 driver and added this as an extension. (IBM Data Server Driver for ODBC, CLI, and .NET.msi) This is my result: 08001 [IBM][CLI Driver] SQL30081N A communication error has been detected. Communication protocol being used: "TCP/IP". Communication API being used: "SOCKETS". Location where the error was detected: "10.10.0.120". Communication function detecting the error: "connect". Protocol specific error code(s): "10061", "", "". SQLSTATE=08001 SQLCODE=-30081 Anybody tried this before??

  Read the article

• GeekTool logs "command not found" for commands that work fine in Terminal

  - by Kevin Dowling

  I'm trying to run simple commands so I can have GeekTool output date/time etc. to my desktop. Should be simple enough to do but it never actually outputs anything into the boxes. Console log shows it's getting spammed by GeekTool to say 'command not found', though the same command (e.g. date +"%H:%M") works fine in Terminal. All I want to achieve is the ability to output a clock displaying time/date on my desktop that fits into my wallpaper. I've tried changing the format of the commands, using the built-in editor window as well as the command line box on the Properties tab. I had a look at the permissions in '/' (because GeekTool runs commands from there) and nothing unusual comes up. None of these solved the issue. When I use a command that simply echo's a string it works (e.g. echo "hello" displays the word hello). Does anyone have experience with GeekTool, and understand why it won't run basic commands? As I say, it's spamming my console with 'command not found' despite them working in terminal... Running OS X 10.6.6 on a MacBook Pro (mid-2010).

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• How to get nginx to pass HTTP_AUTHORIZATION header to Apache

  - by codeinthehole

  Am using Nginx as a reverse proxy to an Apache server that uses HTTP Auth. For some reason, I can't get the HTTP_AUTHORIZATION header through to Apache, it seems to get filtered out by Nginx. Hence, no requests can authenticate. Note that the Basic auth is dynamic so I don't want to hard-code it in my nginx config. My nginx config is: server { listen 80; server_name example.co.uk ; access_log /var/log/nginx/access.cdk-dev.tangentlabs.co.uk.log; gzip on; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_read_timeout 120; location / { proxy_pass http://localhost:81/; } location ~* \.(jpg|png|gif|jpeg|js|css|mp3|wav|swf|mov|doc|xls|ppt|docx|pptx|xlsx|swf)$ { if (!-f $request_filename) { break; proxy_pass http://localhost:81; } root /var/www/example; } } Anyone know why this is happening? Update - turns out the problem was something I had overlooked in my original question: mod_wsgi. The site in question here is a Django site, and it turns out that Apache does get the auth variables passed through, however mod_wsgi filters them out. The resolution is to use: WSGIPassAuthorization On See http://www.arnebrodowski.de/blog/508-Django,-mod_wsgi-and-HTTP-Authentication.html for more details

  Read the article

• Trying to run a codeigniter app on custom php

  - by hamstar

  I have a CodeIgniter app that I deployed to a server with php 5.2 and my dev box has 5.3, and some stuff doesn't work anymore. I didn't want to upgrade php and risk the other app on the server having issues. Anyway I compiled a custom PHP and added the following to a single .conf file in /etc/httpd/conf.d/zcid.conf with all the other conf files. <VirtualHost *:80> DocumentRoot /var/www/cid/app ServerName sub.example.co.nz </VirtualHost> <Directory "/var/www/cid/app"> authtype Basic authname "oh dear how did this get here i am no good with computer" authuserfile /path/to/auth require valid-user RewriteEngine on RewriteCond $1 !^(index\.php|robots\.txt|createEvent\.php|/cgi-bin) RewriteRule ^(.*)$ /index.php/$1 [L] AddHandler custom-php .php Action custom-php /cgi-bin/php53.cgi </Directory> In /var/www/cid/app I have the cgi-bin folder and the php53.cgi that I copied from /usr/local/php53/bin/php-cgi But now when I navigate to the subdomain it says: The requested URL /cgi-bin/php53.cgi/index.php/ was not found on this server. And if I try to browse to /cgi-bin it says (what it is supposed to?): You don't have permission to access /cgi-bin/ on this server. Quite confused now. Anyone know what to do here? Thanks :)

  Read the article

• Apache ScriptAlias and access error?

  - by Parhs

  First of all after much pain i figured out how to make it work in Apache 2.4 windowz. Here is my configuration that seems to work successfully for git clone and push and everything. Problem First of all my configuration works. There is a "Require all denied" at / directory. I want only git functionality and nothing else. Example Request from a git client 192.168.100.252 - - [07/Oct/2012:04:44:51 +0300] "GET /git/simple/info/refs?service=git-upload-pack HTTP/1.1" 200 264` Error caused by that Request [Sun Oct 07 04:44:51.903334 2012] [authz_core:error] [pid 6988:tid 956] [client 192.168.100.252:13493] AH01630: client denied by server configuration: C:/git-server/web/simple There isnt any error at gitclient everything works fine but i get this at error log. Is there any solution for this error to not appear?I worry about log size. <VirtualHost *:80> DocumentRoot "C:\git-server\web" ServerName git.****censored**** DirectoryIndex index.php SetEnv GIT_PROJECT_ROOT c:/git-server/repositories SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER ScriptAlias /git/ "C:/Program Files (x86)/Git/libexec/git-core/git-http-backend.exe/" <LocationMatch "^/.*/git-receive-pack$"> Options +ExecCGI AuthType Basic AuthName intranet AuthUserFile "C:/git-server/config/users" Require valid-user </LocationMatch> <Directory /> Options All Require all denied </Directory> <Directory "C:\Program Files (x86)\Git\libexec\git-core"> Options +ExecCGI Options All Require all granted </Directory> </VirtualHost>

  Read the article

• Jenkins CI - Cannot allocate memory

  - by Programmieraffe

  I tested jenkins-ci successfully on a ubuntu 10.4 (with vmware fusion) on my local computer. Now I want to install and use it on my virtual server at hosteurope. The basic installation was no problem, but now I have problems with my build project. After pulling an mercurial update from a repository, ant is invoked and throws the following error in my build project: "Buildfile: /var/lib/jenkins/workspace/concrete5-seed-clean/build.xml [property] java.io.IOException: Cannot run program "/usr/bin/env": java.io.IOException: error=12, Cannot allocate memory" There is a known problem with heap size at virtual servers at hosteurope (http://faq.hosteurope.de/index.php?cpid=13918), so I tried to set the heap size manually: # for ant export ANT_OPTS="-Xms512m -Xmx512m" # jenkins # edited /etc/default/jenkins, added line JAVA_ARGS="-Xms512m -Xmx512m" # restarted jenkins via /etc/init.d/jenkins restart After setting this for ant, the command "ant -diagnostics" runs through and does not cause an error, but the error still occurs when I try to build the project. Server-Details: - http://www.hosteurope.de/produkt/Virtual-Server-Linux-L Ubuntu 10.4 LTS RAM: 1GB / Dynamic 2GB My questions: - Is 1GB enough for Jenkins or do I have to upgrade the server? - Is this error caused by ant or jenkins? Update: I got it running with ant options -Xmx128m -Xms128m, but sometimes the error occurs again. (this freaks me out, cause i can not reproduce it by now :/ ) Help much appreciated! Cheers, Matthias

  Read the article

• localhost/127.0.0.1 not working, "Unable to connect"

  - by redconservatory

  I am running some pretty basic php sites on Snow Leopard. Usually I just go to my browser and type anything like: localhost http://localhost 127.0.0.1 mycomputername.local But suddenly, after installing a gem file (compass) none of this is working. I tried sudo apachectl restart Thinking that I just needed to restart apache, but no luck. My error log looks like: [Mon Mar 26 09:39:08 2012] [warn] child process 45443 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45223 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45043 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45438 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45049 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45439 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45224 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45440 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45441 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45442 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:10 2012] [warn] child process 45443 still did not exit, sending a SIGTERM [Mon Mar 26 09:39:11 2012] [notice] caught SIGTERM, shutting down I also tried sudo apachectl -k start And I got the error: Syntax error on line 182 of /private/etc/apache2/httpd.conf: Illegal option When I look at the code around that line, I see: <Directory /> Options Indexes MultiViews + FollowSymLinks AllowOverride All Order allow, deny Allow from all </Directory>

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• gitweb- fatal: not a git repository

  - by Robert Mason

  So I have set up a simple server running debian stable (squeeze), and have configured git. Using gitolite, I have all functionality (at least the basic clone/push/pull/commit) working. Installation of gitweb went without any issues. However, when I access gitweb, I get a gitweb screen without any repos listed. # tail -n 1 /var/log/apache2/error.log [DATE] [error] [client IP_ADDRESS] fatal: Not a git repository: '/var/lib/gitolite/repositories/testrepo.git' # cd /var/lib/gitolite/repositories/testrepo.git # ls branches config HEAD hooks info objects refs Here is what I see in /var/lib/gitolite/projects.list: testrepo.git And in /etc/gitweb.conf: # path to git projects (<project>.git) $projectroot = "/var/lib/gitolite/repositories"; # directory to use for temp files $git_temp = "/tmp"; # target of the home link on top of all pages #$home_link = $my_uri || "/"; # html text to include at home page $home_text = "indextext.html"; # file with project list; by default, simply scan the projectroot dir. $projects_list = "/var/lib/gitolite/projects.list"; # stylesheet to use $stylesheet = "gitweb.css"; # javascript code for gitweb $javascript = "gitweb.js"; # logo to use $logo = "git-logo.png"; # the 'favicon' $favicon = "git-favicon.png"; What is missing?

  Read the article

• Problem restoring from tar backup: why are there /dev/disk/by-id/ symlinks and how can I avoid them?

  - by SK.

  Hello, I'm trying to make a bare-bone backup system with the most basic tools available on openSUSE 11.3 (in this case: bash, fdisk, tar & grub legacy) Here's the workflow for my scripts: backup.sh: (Run from external system, e.g. LiveCD) make an fdisk script ($fscript) from fdisk -l's output [works] mount the partitions from the system's fstab [works] tar the crucial stuff in file.tgz [works] restore.sh: (Run from external system, e.g. LiveCD) run fdisk $dest < $fscript to restore partitioning [works] format and mount partitions from system's fstab [fails] extract from file.tgz [works when mounting manually] restore grub [fails] I have recently noticed that openSUSE (though I'm sure it has nothing to do with the distro) has different output in /etc/fstab and /boot/grub/menu.lst, more precisely the partition name is for example "/dev/disk/by-id/numbers-brandname-morenumbers-part2" instead of "/dev/sda2" -- but it basically is a simple symlink. My questions about this: what is the point of such symlinks, especially if we're restoring on a different disk? is there a way to cleanly prevent the creation of those symlinks and use the "true" /dev/sdx everywhere instead? if the previous is no, do you know a way to replace those symlinks on the fly in a text file? I tried this script but only works if the file starts with the symlink description (case of fstab, not menu.lst): ### search and replace /dev/disk/by-id/... to /dev/sdx while read oldVolume rest; do # get first element, ignore rest of line if [[ "$oldVolume" =~ ^/dev/disk/by-id/.*(-part[0-9]*$)? ]]; then newVolume=$(readlink $oldVolume) # replace pointer by pointee, returns "../../sdx" echo /dev/${newVolume##*/} $rest >> TMP # format to "/dev/sdx", write line else echo $oldVolume $rest >> TMP # nothing to do fi done < $file mv -f TMP $file # save changes I've had trouble finding a solution to this on google so I was hoping some of the members here could help me. Thank you.

  Read the article

• How can you connect to a SQL Server not on your domain?

  - by scotty2012

  I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• Loss of network connectivity when playing video on Optoma HD180 projector

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas?

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• Building a Web proxy to get around same-origin restrictions for collaborative Webapp based on a MEAN stack

  - by Lew Cohen

  Can anyone point to books, articles, blogs, or even applications - open-source or proprietary - that detail building a Web proxy? This specific proxy will exist to get around the same-origin restrictions that prevent, for instance, loading a given Website into an <iframe> in a Webapp. This Webapp is a collaborative application in which a group of users log in to the app's Website and can then load different Websites into this app's <iframe> and do various collaborative things (e.g., several users simultaneously browsing a Website, in synch). The Webapp itself is built on a MEAN stack (MongoDB, Express, AngularJS, and Node.js). The purpose of this proxy is not to do anonymous browsing or to bypass censorship. Information on how to build such a vehicle seems not to be readily available from my research. I've come across Glype but am not sure whether this is a feasible solution. I don't want to reinvent the wheel, so if a product is available for purchase, great. Else, we'd need to build one. The one that seems to be close is http://www.corsproxy.com. In effect, we'd like to re-create this since it evidently does what's needed. I don't care what server-side technology is used. Our app is MEAN-based, if that has any bearing. Also, the proxy has to obviously honor basic security considerations (user cookies, etc.) and eventually be scalable. So, anyone know of any sources that would detail how to build one of these? Is it even worth building if something already exists? If so, what would be a good candidate? Any other issues that should be considered with this proxy/application? Thanks a lot!

  Read the article

• Backing up SQL NetApp Snapshots using TSM

  - by WerkkreW

  In our environment we have a 3 node SQL 2005 Cluster which is on NetApp storage. We are currently using SMSQL (NetApp SnapManager for SQL) to take Snapshot backups of the data. This works great, but due to some audit requirements we are also forced to maintain some copies on tape. We have used NDMP in other places across the enterprise but we do not want to use it in this specific instance. Basically what I need to do is, get the most recent snapshot copy of the databases on tape, via Tivoli Storage Manager (TSM). What I have done is, obtained a basic Windows Server 2003 VM with SnapDrive installed, which is SAN attached and zoned to the NetApp, and I have written a batch file to do the following: Mount the latest __RECENT snapshot lun to the host, using a specific drive letter Perform a TSM based incremental backup Dis-mount the LUN This seems to work fine, except sometimes the LUN's do not mount due to some sort of timeout. Also, due to my limited knowledge of windows batch scripting, I have no way to monitor the success or failure of these backups since I do not know how to send a valid return code back to the TSM scheduling service. Is there a more efficient/elegant way to accomplish this without NDMP?

  Read the article

• How to set up port forwarding on a dedicated server running CentOS 5.4 to use Ubuntu 9.0.4

  - by mairtinh

  The basic situation that I have is a dedicated server running CentOS 5.4 At the moment I have one VM running Ubuntu 9.0.4. Later on, I will want to add another VM running Windows Server 2003 but at the moment I am focusing on getting Ubuntu up and running. The Ubuntu installation is working fine but I'm seriously struggling to get port forwarding working so that I can access websites to be hosted on the Ubuntu VM. As a newbie to Linux, I am confused about the relationship between IPTables and VMWare's own port forwarding. Here's what I've tried so far. The IP of my server is xxx.xxx.xxx.xxx and the provider support have told me that the subnet mask is 255.255.255.0, the gateway address is xxx.xxx.xxx.1 and the network address is xxx.xxx.xxx.0. (Those latter two surprise me a bit, I expected private gateway/network address rather than public ones.) First of all I tried Bridged Networking but had no success at all in communicating with the machine other than through the VMware console. I tried pinging it from the host (using ssh into the host) but no joy; also no Inernet access from the VM. I changed the interfaces configuration from DHCP to Static, using a static address of 192.168.1.100 and setting the gateway to xxx.xxx.xxx.1 as advised by the provider. No real difference, still cannot ping the guest from the host or vice versa and no Internet access from the guest. Then I tried NAT. The host automatically set the IP address to 192.168.132.128 with a gateway of 192.168.132.2 Now the guest has Internet access out and when I do a VNC to the host and open Firefox with 192.168.132.128 I can see the hosted website okay but I still cannot get into it from outside. I mentioned that I'm a bit confused about IPtables and VMware port forwarding, what I meant is that I'm not sure whether IPtable forwarding should be set to the IP address of the guest interface (192.168.132.128 in this case) or the gateway address 192.168.132.2 . I have a feeling that I'm missing something very simple here, can anybody tell me what it is?

  Read the article

• Using my old PC as a web/file server?

  - by Garrett

  I have an old desktop computer that I've been trying to sell for AGES. I guess nobody is looking for computers because it was advertised at a dirt cheap price on craigslist, local papers, etc. Anyways, I was wondering if it would be worth it to set it up as a home file server, a web dev server (I have a web host for actual production use), and maybe host a few server applications (ex: ventrillo). The computer is actually an old Dell that I cannibalized after the motherboard being destroyed by lightning, so it has fairly new parts in it. The specs are: P4 3.4GHz w/ HT and Artic Cooling Freezer 7 3GB DDR2 533 RAM 80GB hdd (will upgrade the hard drive if it's even worth using as a server) basic dvd rom 430 Watt Thermaltake PSU (it might be important to note that it is only 60% efficiency) ATI Radeon x600 256MB Antec 300 case It's not a really beefy machine, I just can't see giving it away or putting it in the corner to just collect dust. I have Windows Server 2008 R2 Standard and I am confident in my skills in operating most Linux operating systems. I'd also be using it to tinker with when I learn new things in my server admin classes (I'm finishing my 2nd year in college at the moment so I'm still learning) Also, my house is quite old and the electrical wiring is pretty poor (it MIGHT be up to code, then again, where I live most people don't even know what regulations are or let alone know how to spell it...) Would it be safe to leave it running all day and is it going to run up my electric bill because of the PSU efficiency? I only have 5mbit cable internet, but I won't be running very bandwidth intense services on it so it should be ok. I should elaborate on why I am concerned about the power. The circuits should be fine, but I'm more concerned about fire hazard. What is the likelihood that the server could cause an electrical fire? Again, thank you all for the feedback!

  Read the article

< Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >