Search Results

Search found 14402 results on 577 pages for 'interface builder'.

Page 335/577 | < Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >

• Locate rogue DHCP server

  - by Farseeker

  I know this is a serious long shot, but here we go. In the past week or so, for users connected to a particular switch in our network (there are four dumb switches all connected, and it only affects SOME, not all, users on the one switch) are getting DHCP addresses from a rogue DHCP server. I have physically checked every cable plugged into the switch in question to make sure that none of them have a router or wifi point attached to it. I know the IP of the DHCP server, but I cannot ping it, and it does not have a web interface. Does anyone have any suggestions on what I can do to locate it or shut it down? Unfortuantely all the switches are unmanaged, and as mentioned, there's no physical device (that I can find) plugged in to anything. It's getting critical, because it's screwing up the PXE boot of a whole bunch of thin clients.

  Read the article

• Double default gateway ubuntu server

  - by Elena

  I've just installed an Ubuntu server 9.10 on an EEEBox. This is my /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.48.16 netmask 255.255.248.0 wireless-essid mynet auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask 255.255.255.224 gateway xx.xx.yy.yy When I restart /etc/init.d/networking, I can access the eth0 ip address from the internet and I can ping the machines in my wifi network mynet. Everything works fine and I have one default gateway. But after some time if I check again the route I just find two default gateways: one is correct and is the previous one, but the other is the one of the wifi network. I have a quite low signal of mynet where my server is and sometimes the wifi just disconnect and then reconnect again. Then I think that this can be a problem and the dhcp of the wifi net, when reconnecting it also add a default gateway. Any idea on how to resolve this issue?

  Read the article

• Dell printer goes offline after second print job.

  - by Ac0ua

  Dell printer goes offline(server connection) after second print job. Although the printer's display says it is ready. If you turn off then on the printer you can send one job and goes back offline(server connection) on the next print job. We have multiple Dell 2330dn printers installed through a print server, only one of the printers is experiencing this problem. Two different users. Two different machines. Two different operating systems (win7 and Vista). The computers have been reset. Dell printers have web interface if this helps (through IP address). Thanks for any help!

  Read the article

• Unable to connect to Github for the first time

  - by MaxMackie

  This is my first time with Git and I'm trying to set it up on my box. I added my key to my profile in the Github web interface. When I try to connect... : max@linux-vwzy:~> ssh [email protected] The authenticity of host 'github.com (207.97.227.239)' can't be established. RSA key fingerprint is xx Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added 'github.com,207.97.227.239' (RSA) to the list of known hosts. PTY allocation request failed on channel 0 max@linux-vwzy:~> ssh-add ~/.ssh/id_rsa Identity added: /home/max/.ssh/id_rsa (/home/max/.ssh/id_rsa) max@linux-vwzy:~> ssh [email protected] PTY allocation request failed on channel 0 I'm supposed to be getting some kind of welcome message however, I'm not.

  Read the article

• DHCP Client Can't Find DHCP Server

  - by leeman24

  I currently have 3 machines: CentOS (router) eth1 - 18.0.168.1 eth2 - 145.165.34.1 Windows Server 2008 (server) 18.0.168.2 DHCP scope - 145.165.34.10 - 145.165.34.20 Windows 7 (client) Supposed to use DHCP I can't get my Windows 7 client to get an address from the Windows Server 2008 DHCP server. Every network interface can ping each other (ex. 18.0.168.2 can ping 18.0.168.1 & 145.165.34.1 and the other way around). My Linux machine acting as the router has default IP tables. Other than this command which may or may not be right: iptables -I INPUT -p udp -d 18.0.168.2 --dport 67:68 -j ACCEPT I have also tried it after I flushed the IP tables. I was looking at the dhcrelay command but it seems CentOS doesn't have it and I am not even sure how to use it.

  Read the article

• Gre Tunnel Cisco Linux traffic forwarding

  - by mezgani

  I setup a gre tunnel a cisco router and a Linux machine, the tunnel interface in the Linux box named pic. Well i have to forward traffic coming from cisco through the Linux box. the rules i've set in the Linux box is described as follow: echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -i pic -o ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i ppp0 -o pic -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE I see the traffic coming from tunnel and forwarded to internet but no reply from sent packet. May i miss something like a routing rule.

  Read the article

• Add IP Address without Plesk

  - by CrackerJack9

  I have an dedicated unmanaged server and added a few IP addresses to it (allocated), and the only information my hosting company has provided is instructions on how to use Plesk to Add IP Addresses. However, one of the first things I did was uninstall Plesk (for numerous reasons). Does anyone know what exactly Plesk does when you "Add IP Address"? Does it just create an alias on the default interface (I currently only have one and the loopback)? I can manage that myself without Plesk, but I was hoping someone might know if there is anything else Plesk does. I also have DHCP Client running (eth0 is static), not sure why my hosting company put that there either, and not sure if they're related.

  Read the article

• Static route in conflict with a default route

  - by Ossan Sokiv

  Hi guys, I have a default route configured. 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.1 I'd like to add a static route to pass traffic destined for 192.168.1.51 via a load balancer's redundant virtual interface at 192.168.1.2. ip route add 192.168.1.51 mask 255.255.255.255 via 192.168.1.2 When I try to add the static route I get this error. Error: either "to" is duplicate or "default" is garbage." It doesn't want to add the static route because it's in conflict with the default route. Is there a way around this? Regards Ossan

  Read the article

• Share laptop Wi-Fi with router set up as access point via ethernet cables

  - by obie

  I have an ADSL modem which serves as a wireless router. There's a laptop connected to it through cable. On the other room I have a laptop which is connected through the router wirelessly. Since I have other appliances that need to get connected but are not Wi-Fi capable I have another Wi-Fi router. How can I share the second laptop's Wi-Fi with the second router so that the router can then serve as an access point to give internet to my other appliances through ethernet cables? I want something like this: INTERNETMODEM (WIFI)LAPTOP 1 (WIFI)LAPTOP 2 (WIFI)Router 2 (ETHERNET)DREAMBOX & WDTV What I've tried so far is opened the admin interface of router 2 then set static IP 192.168.100.13 and disabled the DHCP. The DHCP of the main router starts with 192.168.100.1 then I hooked up router 2 with the laptop 2 through Cat5 cable but for some reason it's not working.

  Read the article

• Windows XP/7: custom routing for VPN connection

  - by Peter Becker

  We are dealing with a badly configured VPN connection from a vendor, which set up the default gateway but doesn't route traffic anywhere beyond their VPN zone. I managed to do some ad-hoc routing to configure a computer in a way that it can reach the vendor's VPN, our local network as well as the internet. I then tried to turn this into a script, but that failed since the interface number of the VPN changes on every connection. Is there a way in Windows XP and/or Windows 7 to configure custom routing on the client side of a VPN connection? What I would like to do is to have a script running just after the connection comes up that changes the routing table (similar to an ifup script on UNIX).

  Read the article

• Using tshark to generate traffic logs every X seconds

  - by Sridhar Iyer

  I'm trying to use tshark to maintain a running history of all the packets that are going through an interface, for say 30 seconds. I want it to be human readable. This is a linux machine, and without mucking too much into the netstack source (which I can do if push comes to shove), I was wondering if I can use tshark to this. tshark has a -b duration:10 -b files:2 which I can use to generate a rotating set of 2 files, but I don't know which format it is printing the file in or how to read it.

  Read the article

• Choosing a very basic Linux distro with minimal boot time?

  - by user30961

  I've had Ubuntu for a year now, like it but it doesn't match my needed configuration for my old laptop. So... I am using Linux mainly for webapps so I don't care much about user interface. What I need is a distro which is small enough to install on a SD memory card (or USB) since I am removing the hard drive, all my data is in the cloud. I also want it to have as short boot time as possible. I tried Puppy Linux and it seems ok but it had preinstalled looots af small apps I don't need, I would really like to have a distro with minimal preinstallations and add them on my own. So what are my choices and why would you recommend these?

  Read the article

• Why after deleting a 110+ GB collection, my /var/lib/mongodb directory still have same size?

  - by tunnuz

  I am having some troubles with MongoDB and space usage. In particular, I once used to have a large collection of about 600 million records totaling 110+ GB on disk. Recently I decided to drop it because the data was outdated, to do so I dropped the collection through rockmongo's web interface. Accordingly, rockmongo doesn't show me the collection anymore, however my disk usage hasn't changed at all. Is there any clean operation which I am not aware of, which must be run in order to synchronize the database with database files on disk? I have tried to perform a "repair" but the system complains that there's not enough space on disk ... that's because it is all used by MongoDB.

  Read the article

• How to change the fonts used in Foxit Reader?

  - by user982438

  I really want to use Foxit Reader as my default PDF reader for its Tab Interface, and low memory footprint. Having tried mutiple times over the years the only thing that is stopping me are the Fonts. PDF in Adobe Reader looks Regular, but PDF Rendered in Foxit Looks Ugly. Would this solution works in Chrome as well? Since i record Chrome is using Foxit Reader as its embedded PDF engine. And is there any reasons why Fonts are used differently in Adobe and Foxit Reader?

  Read the article

• Route from Cisco ASA over site to site VPN

  - by Wookie321

  I want to be able to push f/w logging traffic to a server at a remote site. This server is accepting syslog traffic on port 514. In the ASA I've configured it to use this server as a syslog server. The Cisco f/w's inside interface address is 10.0.0.1 and I want to route over the link to an address of 192.168.1.1. The vpn is up and working between sites, and local clients at each site can access resources etc. How would I go about setting up the route from the f/w to this remote server only?

  Read the article

• Software for monitoring internal software?

  - by Tyler Eaves

  Is there any good software for monitoring the health of a collection of related software? Requirements are as follows: Web-based, deployable on standard Linux/BSD software. Configurable to support a variety of processes, scheduled at various intervals. Some sort of dashboard interface, for monitoring status, viewing errors, etc. As an example, suppose we have a daily export that's scheduled to run at 6AM each morning. After the export completes, it would POST a status message, saying it had completed, passing in some sort of application key to identify the export. If that status message hadn't come in, by, say, 6:30AM, an e-mail might be sent, that application should go red on the dashboard, etc. Applications should also be able to post error/warning messages. Basically the goal is to be able to monitor all of our internal projects from one system, rather than a multitude of e-mails, log files, etc. I suspect that I'll probably have to end up writing this from scratch, but I just thought I'd ask.

  Read the article

• Allow Incoming Responses Apache. On Ubuntu 11.10 - Curl

  - by Daniel Adarve

  I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping https://www.veripayment.com/integration/index.php ping: unknown host https://www.veripayment.com/integration/index.php daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms PHP Function in codeigniter public function authorizePayment(){ //--------------------------------------------------- // Authorize a payment //--------------------------------------------------- // Get variables from POST array $post_str = "action=payment&business=" .urlencode($this->input->post('business')) ."&vericode=" .urlencode($this->input->post('vericode')) ."&item_name=" .urlencode($this->input->post('item_name')) ."&item_code=" .urlencode($this->input->post('item_code')) ."&quantity=" .urlencode($this->input->post('quantity')) ."&amount=" .urlencode($this->input->post('amount')) ."&cc_type=" .urlencode($this->input->post('cc_type')) ."&cc_number=" .urlencode($this->input->post('cc_number')) ."&cc_expdate=" .urlencode($this->input->post('cc_expdate_year')).urlencode($this->input->post('cc_expdate_month')) ."&cc_security_code=" .urlencode($this->input->post('cc_security_code')) ."&shipment=" .urlencode($this->input->post('shipment')) ."&first_name=" .urlencode($this->input->post('first_name')) ."&last_name=" .urlencode($this->input->post('last_name')) ."&address=" .urlencode($this->input->post('address')) ."&city=" .urlencode($this->input->post('city')) ."&state_or_province=" .urlencode($this->input->post('state_or_province')) ."&zip_or_postal_code=" .urlencode($this->input->post('zip_or_postal_code')) ."&country=" .urlencode($this->input->post('country')) ."&shipping_address=" .urlencode($this->input->post('shipping_address')) ."&shipping_city=" .urlencode($this->input->post('shipping_city')) ."&shipping_state_or_province=" .urlencode($this->input->post('shipping_state_or_province')) ."&shipping_zip_or_postal_code=".urlencode($this->input->post('shipping_zip_or_postal_code')) ."&shipping_country=" .urlencode($this->input->post('shipping_country')) ."&phone=" .urlencode($this->input->post('phone')) ."&email=" .urlencode($this->input->post('email')) ."&ip_address=" .urlencode($this->input->post('ip_address')) ."&website_unique_id=" .urlencode($this->input->post('website_unique_id')); // Send URL string via CURL $backendUrl = "https://www.veripayment.com/integration/index.php"; $this->curl->create($backendUrl); $this->curl->post($post_str); $return = $this->curl->execute(); $result = array(); // Explode array where blanks are found $resparray = explode(' ', $return); if ($resparray) { // save results into an array foreach ($resparray as $resp) { $keyvalue = explode('=', $resp); if(isset($keyvalue[1])){ $result[$keyvalue[0]] = str_replace('"', '', $keyvalue[1]); } } } return $result; } This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever Thanks in Advance

  Read the article

• Fastest way to move files from a guest VM to the host?

  - by iTayb

  Hey there. I'm looking for the fastest way to copy files from a VM to physical servers. Setting up a network between them isn't a thing I'd like to do. I believe it is much more secure when not having one. VMware suggests using the Copy-VMGuestFile cmdlet from their PowerCLI interface, however I find it slow (Running at approximately 1.5MB/s). I thought of the following: Creating a new virtual hard drive, moving the files in, and download the .vmdk file from the server, then extracting it locally. It is possible, however will not work with working VMs, and I don't want to shut-down the VM every time I want to move files. Use the virtual floppy device and download the .flp file. It works even if the VM is running, but it is limited to 2.8MB. Do I have any other way? I'm using ESXi 4.1. Thanks.

  Read the article

• DNS Settings in Cisco Wireless Lan Controllers

  - by Braden

  The WLC is a 2100 series and I have looked back and forth through the entire web interface. Originally the idea was that the gateway should be the DNS controler and the WLC pointed directly at the gateway. For some reason, random clients are having DNS specific issues when it comes to seeing certain shares around the network. The problems are also very intermittent. Aside from going to each box and implementing a static DNS is there ACTUALLY a DNS setting lodged into the WLC settings (and I am being a numpty and can't find them) or am I stuck with performing the config 1 by 1?

  Read the article

• NIC models for HVM guests in Xen 4.0

  - by Jed Daniels

  Is there a list of NIC models that I should use with various HVM guests in Xen 4.0? Is there even a list of possible choices for the model=field? I'm planning on running both Windows and FreeBSD guests on the particular Xen box that I'm configuring now, and ideally I'd like a setting that can work on both of them and get me gigabit speeds without a lot of extra hassle loading special drivers (similar to VMware's e1000 NIC option). Any suggestions? The vif line I'm currently using in my config is: vif = [ 'type=ioemu,bridge=eth0,model=ne2k_pci,script=vif-ovs' ] This works in my Windows XP SP3 VM, but is only recognized as a 10Mbit interface. Changing to model=e1000 or model=i82557b resulted in Windows not being able to find a driver for the NIC.

  Read the article

• Reliable cheap or free DNS service?

  - by superwormy

  I'm looking for a reliable free or cheap DNS service. I've used FreeDNS at FreeDNS.Afraid.org in the past, but it doesn't always seem reliable... sometimes people say they can't access my website (sometimes I can't access it either) by domain name, and yet if I type in the IP address it works fine, so I assume it's some sort of DNS problem. Are there any other cheap or free DNS services out there? I need something reliable that I can manage via a web interface (or scripts if they have an API) that I can use to manage the DNS for ~100 domain names. EDIT: To be clear, I'm looking for DNS hosting, not DNS servers to use for my WAN connection.

  Read the article

• Is it possible to a VM inside a VM (e.g., KVM on Vmware)?

  - by lorin

  I'd like to do some development on Eucalyptus, an open source project which provides an Amazon EC2 interface for launching virtual machine instances on a collection of privately managed nodes. I'd really like to be able to do some of the development on my desktop, rather than having to deploy Eucalyptus on our shared local cluster each time I make a change to the source code. (Especially since there are a group of us sharing that test cluster). Unfortunately, my desktop machine is a Mac, which won't run Eucalyptus natively. I do have VMWare Fusion, and it would be really nice if I could do my Eucalyptus testing inside a VMWare instance. The problem is, to test out Eucalyptus, it will have to launch (KVM or Xen) VM instances. I've got no idea if it's possible to actually launch a KVM or Xen instance inside a VMWare instance.

  Read the article

• Is it possible to disable ARP in Windows 7

  - by DriverGuy

  I have a unique requirement where I need to disable ARP on a Windows 7 box. In previous Windows versions you could modify the ArpRetryCount in the registry (and set it to 0), but this does not work in 7 (nor does it exist). Does anybody know how, or if this is possible? I've been asked to elaborate this more and I'm not quite sure how. I want to switch off ARP (including gratuitous arp) on Windows 7 for a project I'm working on. You can do this in Linux by simply adding '-arp' when you bring up an interface, but you cannot do this in Windows 7. You could in previous versions by modifying the registry, but this does not work any more. If the fine folk here aren't sure then I don't like my chances...

  Read the article

• Exposing the ipPhone attribute to Communicator and the OCS address book service

  - by Doug Luxem

  I am in the process of integrating OCS with our Cisco phone system using CUCIMOC. After some fiddling with the phone normalization rules, it appears that I can get PSTN numbers to be dialed though the CUCIMOC interface (yay!). However, during this process I came to realize that the ipPhone attribute in Active Directory does not appear to be exposed to Communicator (and CUCIMOC). What is strange though, is that I can see from the OCS address book service "Invalid_AD_Phone_Numbers.txt" that the attribute is processed by the address book service. My question is, how do I expose the ipPhone field in Office Communicator? Currently, Communicator maps like this - Work = telephoneNumber Mobile = mobile Home = homePhone Attributes such as otherHomePhone, ipPhone, otherMobile, otherTelephone, otherIpPhone are ignored.

  Read the article

• USB to LPT adapter?

  - by Dave

  I'm bummed out, pretty much all of our computers here lack parallel ports. I have an EETools ChipMax programming tool that has one of the old-school Centronics connectors on the back. I figured that someone must make a USB to LPT adapter. Sure enough, I found one from iogear, the GUC1284B that is a USB to Parallel Printer cable. Note the boldface on the Printer. It must connect to a printer -- it isn't some generic USB to parallel interface, unfortunately. Does anyone here know of an adapter that works for parallel devices that aren't printers? I'd hate to have to buy a USB version of the ChipMax when I don't need to use it very much.

  Read the article

< Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >