Search Results

Search found 13200 results on 528 pages for 'wcf testing'.

Page 340/528 | < Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >

  • ldirectord refusing connection when nginx redirects from http to https

    - by Adam
    I am running ldirector as a load balancer to an nginx front end server. If I setup a redirect from http to https and connect directly to the nginx server, all is well. Connecting via ldirector causes my connection to be refused. I can connect normally via http or https through ldirector when I don't have the redirect in place. To add to my confusion, if my application issues a redirect from http to https, it works. I am testing this via curl on the command line. (curl: (7) couldn't connect to host vs a response) I am using the standard ldirectord config (http://www.ultramonkey.org/3/topologies/config/lb/non-fwmark/linux-director/ldirectord.cf) the http and https parts. My nginx config for the redirect is simply: location / { rewrite ^(.*) https://$host$1 permanent; }

    Read the article

  • Is it possible to modify a color scheme and windows decorations in Xfce4?

    - by Juhele
    just testing PCLinuxOS Phoenix XFCE Edition 2011-07 which I would like to install on my grandpa's PC instead older PCLOS 2009 with KDE3 (which is almost impossible to upgrade). The PC is relatively older one (Sempron 2200+ CPU, MSI K7N2GM2 board with integrated GeForce 440MX series graphics, 1GB RAM and 80GB IDE HDD) and I thought that it is too weak for KDE4. I already used Xfce in the past (Sam Linux 2006 and 2007), but in new Xfce4 I am not able to somehow change the windows color scheme and the windows decorations - the settings manager offers me switching between preinstalled themes but it is possible to modify them with some GUI?

    Read the article

  • How can I simulate a slow machine in a VM?

    - by Nathan Long
    I'm testing an AJAX-heavy web-application. I develop on a new Mac, but I use VmWare Fusion (currently 3.1.2) to test in Windows XP, using IETester to simulate older versions of IE. This lets me see how older IE versions would render the site, but I'd also like to see how the site would perform on an older machine. I see in the VM's settings that I can decrease the RAM; is there a way to also dial down the processor speed? How else might I simulate a slow machine? (I am also going to check out how to simulate a slow internet connection.)

    Read the article

  • Can PuTTY be configured to display the following UTF-8 characters?

    - by Stuart Powers
    I'd like to be able to render the characters as seen in this tweet: I saved the tweet's JSON data and wrote a one-liner python script for testing. python -c 'import json,urllib; print json.load(urllib.urlopen("http://c.sente.cc/BUCq/tweet.json"))["text"]' This next image shows the output of this command on two different putty sessions, one with Bitstream Vera Sans Mono font and the other is using Courier New: Next is an example of correct output (I wasn't using PuTTY): The original JSON is at this link using Twitter's API. How can I get PuTTY to display those characters?

    Read the article

  • Gmail not accepting mail

    - by BARON'S
    I'm setting up a new mail server with postfix dovecot and things are working fine except this strange thing. I'm unable to send email to gmail addresses. The log shows status sent. However, I checked there is no email in gmail mailbox. Jul 8 13:10:08 example postfix/smtp[5294]: B53B637C233: to=<[email protected]>, relay=gmail-smtp-in-v4v6.l.google.com[173.194.79.26]:25, delay=2.2, delays=1.5/0.08/0.49/0.14, dsn=2.0.0, status=sent (250 2.0.0 OK 1341727808 nc7si50672387pbc.75) However, my other account can send to gmail. After several testing, then I found that if I first send email from gmail, then subsequently I can send from my server and email received by gmail. I don't have this issue with Yahoo. What could be the problem?

    Read the article

  • Tunneling HTTPS traffic via a PUTTY/SSL tunnel with SOCKS

    - by ripper234
    I have configured a SOCKS ssh tunnel to a remote proxy, and set my Firefox to use localhost:<port> as a SOCKS proxy. My intention is to tunnel outgoing HTTP/S connections from my machine via a specific 3rd party server I own (on AWS). In my testing, HTTP UTLs are forwarded properly (e.g. when I access http://jsonip.com/ from my computer I do get the server's IP) However, whenever I try to reach an HTTPS address, I get this error: The proxy server is refusing connections How do I debug/fix it? My PUTTY tunnel config is simply (some random source port number + dynamic checked): P.S. I'm aware I might need to manually accept SSL certificates. The reason I'm doing this is to resolve problems using gmail as an outbound SMTP service.

    Read the article

  • Downgrade 'local' packages in Debian/Ubuntu

    - by Matt Joiner
    I recently unticked the "pre-released updates" option in Software Sources on my Ubuntu Lucid 10.04.1 installation. The Ubuntu wiki states the following regarding this source: The proposed updates are updates which are waiting to be moved into the recommended updates queue after some testing. They may never reach recommended or they may be replaced with a more recent update. Roughly 20 installed packages have indeed not made it into recommended updates, and occasionally cause conflicts when I install new software, as related packages of the newer version are unavailable now that I've disabled the source. How can I force a downgrade of all packages for which an earlier version exists in a enabled repository?

    Read the article

  • Converting PDF eBooks into a Kindle format

    - by Ender
    Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this?

    Read the article

  • Apache only logs PHP errors if LogLevel is set to debug

    - by Sudowned
    I'm developing a CodeIgniter application and for reasons that I do not fully understand errors have stopped being logged in the file specified in the Apache site conf. The page I'm testing is definitely generating a 500 error, but that is not reflected in the logs unless I set LogLevel debug. Setting LogLevel to error or warn results in no errors being logged. I don't think this is a CI issue because I've been developing this site for close to a week now and errors have been logged as expected until I picked the project up again this morning. Though for what it's worth, I've got: error_reporting(E_ALL); set in my index.php.

    Read the article

  • What is a preferred method for automatically configuring and setting up an Ubuntu instance?

    - by sutch
    I am tired of manually configuring instances of Ubuntu for testing web applications and for setting up workstations. I'm even more frustrated by the issues caused by inconsistent configurations. Is there a method (hopefully not too time consuming to learn and setup) that allows for automation of the setup and configuration of an Ubuntu server or workstation from an ISO. This is primarily for virtual machine instances, but it would be helpful to also create instances on hardware. I am specifically looking for a method to automate the installation of libraries (apt-get), configure services (such as Apache and MySQL), add 3rd party software (download, extract and build), and add libraries to scripting languages (for example, Ruby Gems or CPAN packages for Perl).

    Read the article

  • How can browsers in VMs resolve hostnames of websites on parent PC?

    - by elliot100
    I have a number of local websites in development on my Windows PC, set up as virtual hosts within Apache, with hostnames (along the lines of dev.example.com) resolved via the hosts file, so I can test them out them with various browsers. I now want to extend browser testing to running browsers in various OSs in virtual machines, and want to be able to resolve dev.example.com from the VMs. Currently these are a mix of VMWare Server and VirtualPC. I know I can edit the hosts file on any Windows VMs, but this is a bit fiddly and I'd like a solution which is independent of the individual VMs. I think what I need is a nameserver, but what's the simplest way of going about this? I'd like everything to be self-contained on the one machine. I think I can cover firewall and Apache permissioning issues.

    Read the article

  • How do i get Safari to ignore the SSL Certificate error?

    - by Tangopop
    In IE 6, 7, 8 and Firefox 3.6.3 and 3.0.5 i have installed a local SSL Certificate on the machine i am testing on and i have gotten the browser to igonre the SSL error (which is off one of my Web Test servers) Now i am tryin to do the same thing within safari 4 and with no luck. Basically i am running some automated scripts to test my website before they go live and i need to be able to ignore these errors as they will all run autonomosly. This is the error screen i am trying to avoid: http://library.bowdoin.edu/news/images/ezproxy-err/safari.jpg As i say i have installed the certificate locally and the IE 7 browser on the same machine works fine.

    Read the article

  • Why has ESXi 5.0 not used the software RAID configuration on my test server?

    - by kafka
    I've got a test server which was running WS 2008 Enterprise on the bare metal. It was correctly using the software RAID 1 configuration (2x250 GB disks which appeared as one disk), setup on the Dell Poweredge T110 (which meets compatibility requirements) without requiring any extra setup from me. (As an aside I'm fairly sure it's software RAID, as we didn't spec a hardware RAID controller, if that's of any importance in this situation). I am now testing installing ESXi 5.0 on this server to run some VMs. I've successfully installed ESXi, and imported a VM fine, but it's showing 2 x 250 GB disks available as datastores. However they should be appearing as one volume. When I boot the server, there is a RAID configuration screen you can enter, and I'm guessing this is what I'll have to do at some stage, but now need to be very careful because there is one disk which contains data that I want to be mirrored on the other disk. What is the best thing to do in this situation?

    Read the article

  • Localhost permissions given different values in fireftp and cs4 dreamweaver

    - by YsoL8
    While testing a file uploader on my localhost ( mamp on mac ) I've hit a problem. Trying to fix a folder permissions problem, I used CS4 Dreamweaver's permissions screen to set 0777 permissions. However these wouldn't apply and stayed stuck on 0, so I opened fireftp and accessed the folder in the local panel. The permissions there are 0777. So I have a folder that has permissions of 0 and 0777 at the same time. How can I resolve this and make sure the permissions are 0777?

    Read the article

  • Debian: video problems with VLC

    - by kemp
    I have a problem playing AVI divx files with VLC. Yesterday upon start VLC showed an error message complaining about divx codecs and refused to proceed. Today the player starts but the video is squashed horizontally (it occupies roughly 1/4th of the VLC window which is for the other part black). I'm on an updated testing system, and before yesterday VLC was playing fine. In the meantime - after a recent dist-upgrade - I cannot run X with proprietary ATI drivers anymore, I have to use the FOSS radeonhd ones instead. I don't know if that's related but I thought it could be worth mentioning (and by the way if anyone has suggestions about this problem too, that'd be very much appreciated). How can I fix VLC's problem?

    Read the article

  • What constitutes valid justification for more IP addresses?

    - by David
    I host a small website with a well known VPS service. They provided me with one IPv4 address upon registering and said additional addresses would require justification. I requested one additional IPv4 address so as to have one for a production environment and one for a testing/QA environment. They said this was unnecessary as I could just use alternative TCP ports for the test environment. I can live with using a non-standard port for non-production hosting, but it got me thinking, what would be valid justification? (I asked them and they didn't want to answer). Is there an industry standard for what counts as "valid" justification for additional IPv4 addresses?

    Read the article

  • Exclude path from Windows 7 search?

    - by Jez
    It's really quite incredible how bad Windows 7's search seems to be. The latest problem I have with it is that I want to search for filenames including the string "user", so I go to the directory I want to search in (C:\Users\jez\testing), type *user* in the search box, and hit enter. It gives me... every single file. Because "user" is in the path of every file, with everything being under "C:\Users..." OK, this is useless. Is there a way to just search for the string within files rather than their paths, or do I need to download some decent 3rd party search software?

    Read the article

  • Orange Brightbox and NO-IP.com

    - by JSweete
    Strange one here i didnt know where to ask, and i know this is a developer resource but i was hoping with everyones tech know how someone may have a solution for my problem. Ok i had an orange livebox before and in the dynamic dns settings it had no-ip.com as a drop down option with login variables to update my account with a dynamic ip address. This worked great for years. However my livebox died and i now have a orange brightbox, and this doesnt have no-ip.com as a login update option for dynamic dns on my router. Does any one have any idea how i can get my domain to point to my home server with a dynamic ip address ideally for free? This is merely for testing and to have a backup server for my main remote server.

    Read the article

  • Forward requests to IIS Application/Folder to Apache server on another port

    - by TheGwa
    I have found many questions and answers for ways of doing this using asapi filters or ARR and URL Rewrite, but none are clear and concise and I am sure many people have this issue. I am looking for a best practice step by step solution to the following scenario: I have a development server accessible externally via a specific port for testing. Eg. rnd.domain.com:8888. So there is one port in and out of this machine accessible to the world. On this server I have a number of Apache or other servers using specific ports such as 8080. IIS is bound to port 80 locally as well as 8888 to get external requests and works perfectly. I would like to use an application (folder) in IIS such as rnd.domain.com:8888/mapserver to map to the local apache server in both directions. The same solution must apply in production where the domain is mapped to port 80. eg. production.domain.com/mapserver maps to 8080 on production server

    Read the article

  • RDP add domain users broken

    - by Robuust
    I have 3 servers, - domain controller with dns services - dhcp/rras - file/random server with files stored on it and nothing special so far. All servers have static IP's All servers are in the same domain (SOFTWARE) RDP is enabled for all 3 servers All servers are Windwos Server 2008 R2 I can connect to the DHCP/RRAS server via RDP I cannot connect to DC and File server When I add RPD users (both are domain admin for testing) to the File server they show up like this: What is happening what I don't see? And additional why don't I even get a login screen for RPD? Thanks in advance.

    Read the article

  • NTFS write speed really slow (<15MB/s)

    - by Zulakis
    I got a new Seagate 4TB harddrive formatted with ntfs using parted /dev/sda > mklabel gpt > mkpart pri 1 -1 mkfs.ntfs /dev/sda1 When copying files or testing writespeed with dd, the max writespeed I can get is about 12MB/s. The harddrive should be capable of atleast 100MB/s. top shows high cpu usage for the mount.ntfs process. The system has a AMD dualcore. This is the output of parted /dev/sda unit s print: Model: ATA ST4000DM000-1F21 (scsi) Disk /dev/sda: 7814037168s Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 2048s 7814035455s 7814033408s pri The used kernel is 3.5.0-23-generic. The ntfs-3g versions I tried are ntfs-3g 2012.1.15AR.1 (ubuntu 12.04 default) and the newest version ntfs-3g 2013.1.13AR.2. When formatted with ext4 I get good write speeds with about 140MB/s. How can I fix the writespeed?

    Read the article

  • Automation Question using VMWare Workstation

    - by James K
    I'm running an experiment that requires me to create 100 instances of Windows XP w/SP3 and saving each VM instance off to a hard drive. I have to annotate the time that the VM load starts (starting my timer when I see the "Setup is preparing...") until the load ends when I see the final desktop after VM loads its drivers. I also have to annotate the host start and stop time. Is there any way this process can be automated? Each load runs me about 16:00 minutes and gets real tiresome after a time. BTW... Exact timing is not necessary, eyeballing as described above is sufficient for my testing needs.

    Read the article

  • OWA (Outlook Web Access) won't give user a link to attached document. Gives "Open as Web Page"

    - by Jerry Mayers
    I have been testing OWA and have found that when there is an attached file on a message it shows the "Attachments:" then the file name (but no link) and then [Open as Web Page] link. The user has to click on that which opens a new window and previews the document, then the user gets "You are currently viewing:" followed by the file name. This time the file name is a link that they can open/download. This happens for Office documents and PDF file at least. How do I make it so users can get a direct link to the file on the original message window?

    Read the article

  • Unresponsive virtual OS

    - by confusedGeek
    Hopefully someone has a suggestion on how to resolve this. Configuration Host: Win 2003R2 w/Virtual Server 2005R2 Virtual1: Win 2003R2 w/Sql Server 2005 Virtual2: Win 2003R2 w/WSS 3.0 Situation This past weekend the power went out and took down the servers (no UPS, it's a desktop standing in as dev testing server). Since the servers went down the Virtual2 server after running WSS fairly heavily for an hour to two will become unresponsive via HTTP. If I login via virtual server's remote control I don't get anything beyond a background screen. The CPU counter on the virtual server's master status shows that it isn't doing anything. The only thing I have been able to do is to turn off Virtual2, which loses any state changes. Shutdown commands issue from the virtual server master status are ignored. After restarting Virtual2 the event logs and application logs don't indicate what caused the problem. Anyone have an idea as to how to repair the OS, or maybe what could be the problem? Thanks ahead of time.

    Read the article

  • Do two portforward rules translate to "and"?

    - by blsub6
    I just set up an Exchange server to replace my DeskNow mail server. I want to start testing my internet mail exchange of my Exchange server. I can only set the MX records on my DNS up to my one external IP address so I was thinking that I could set up a firewall rule on my internet-facing firewall that port forwarded the smtp packets to two different servers. My question is: If I do that, will that mean that the smtp packets will be forwarded to just the first internal IP on the list? Or does it mean that the packet will be cloned and sent to both IPs?

    Read the article

< Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >