Search Results

Search found 12988 results on 520 pages for 'performance'.

Page 344/520 | < Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >

• SSD install - what do I need to watch out for when reconfiguring SATA ports?

  - by tim11g

  I installed a Samsung 840 SSD in a Windows 7 machine. It seems to be working fine, but I'm not seeing the expected performance. The AS SSD benchmark gives 76 for read and 138 for write. At the upper left of the benchmark it says "pciide - BAD" and "31K - BAD". I'm assuming the "pciide BAD" means the motherboard (Gigabyte GA-P35-DS4) is configured as IDE emulation and needs to change to native SATA. I don't know what the "31K" refers to. The bios settings look like this: I saw this article that indicates that changing the SATA mode of the boot drive can cause problems (Blue Screen): Error message occurs after you change the SATA mode of the boot drive What is the correct procedure to change the SATA Mode without causing a system failure? Apply the registry change from the MSFT article above first, then reboot and change the SATA mode? Will the SATA mode change in the BIOS affect other drives?

  Read the article

• Sync a specific folder of contacts to iPhone

  - by colemanm

  Is there a simple way to organize contacts in Outlook/Entourage and only have a subset of them synchronize with the iPhone over Exchange ActiveSync? Our CEO has thousands of contacts in his mailbox, but would prefer if only a small portion of them synched to his phone over the air... The iPhone's performance takes a huge hit keeping that massive dataset in order. If he could put some of the records in subfolders or something and only sync the top level, I think that would work for him. Does anyone know if this is possible?

  Read the article

• Advice for migrating email server

  - by Chris Adams

  Hi there, I'm planning to migrate a Zimbra server with about 200gb of data from a server hosted in an office into a datacentre, to increase uptime (we've had a couple of outages when our network here started flaking out, and we have people in other countries relying on this server too). However, I'm not sure how best to migrate the data into the data centre without rendering the connection unusable during office hours, because there's far too much to send in over night over the two meg upstream connection we have here. I'm familiar with using tools like nice to stop a long running process degrading machine performance - is there a simple way to throttle a connection between office hours, so the long running transfer doesn't block the pipe, but then opens up outside of office hours to make the most of the bandwidth? I'm aware the alternative here is to simply mail a hard drive to the data centre, but I'd like to avoid doing that if I could. We're using Centos Linux for our servers, in the office and the datacentre, so extra points for an open source linux answer.

  Read the article

• concrete uses of LDAP?

  - by ajsie

  im new to LDAP. i wonder what are some concrete examples of using LDAP. things that are MUCH more easier to do when you got 3-7 linux computers in a small company network. one use that is very important for me seems to be that you configure LDAP to handle system authentication. then you dont have to create same accounts in all computers. are there other things that are a MUST DO for a small network to save more time? my small network is for apache servers and database servers. and should LDAP be in an own machine? cause i guess its not good to put it in apache or database servers since these are performance dependent.

  Read the article

• using nmap to guess remote OS and probe service details on a single port only

  - by WoJ

  I am looking at scanning with nmap a large network in order to identify the OS of devices (-O--osscan-limit) probe for details of a service on a single port (I would have used -sV for all open ports) The problem is that -sV will probe all the ports (which I do not want to do for performance reasons) and I cannot use -p to limit the ports to the one I am interested in as this impacts the OS fingerprinting. I could not find anything in the manual to limit the service probing. Thank you for any ideas (including other approaches outside of nmap, though I would prefer to stick to nmap)

  Read the article

• How to force my laptop to use the discrete GPU?

  - by Anton Roth

  My laptop (Asus X7BSV) is stuck using only the integrated GPU. It has a nVidia GT540M as well, but I cannot get it to work. I am using a Windows 7 x64 with latest drivers. This occurred after I attached an external USB monitor I need for work, and since then I cannot swap back to the nVidia GPU (dxdiag for example says that the primary GPU is the Intel integrated one). Asus support asked me to completely reinstall the system, but that is something I do not want to do. I checked the BIOS, there is no option as to what GPU to use. The nVidia card itself is working, since I can use CUDA on it, and it worked with a Ubuntu Live CD. In the nVidia software management I tried setting it to global setting, high performance GPU (nVidia), but that had no impact. What am I missing here? I did uninstall/delete all drivers and software related to the external monitor, but that did not help.

  Read the article

• What can I do to enhance MacBook Pro internal mic sound quality in iMovie?

  - by gaearon

  After using MacBook for two years, I bought 17'' MacBook Pro. I'm pretty happy with it, performance and all, but I also was going to record some music videos for YouTube. I play guitar and sing. However I was extremely disappointed with the sound quality that comes by default. I'm 100% sure my 13'' MacBook mic was much better at recording music and singing. Currently mic can't event handle acoustic guitar, outputting sound you'd think was recorded 5 years ago in ARM format on a Nokia phone on a loud concert. It totally feels like some lame filter is cutting low and high frequencies. I want to know what settings (visible or hidden) in iMovie or Mac OS itself I might want to tweak in order to get my MBP mic record clean sound.

  Read the article

• Where should I go to learn about networking? [closed]

  - by Ollie Saunders

  I wonder if anyone could recommend resource or resources such as a good book that: explains how all the important protocols work and interact. I’m interested in those that are relevant in a typical home network and used over the Internet explains in detail how ADSL Internet connections work to the level of depth necessary so that I’m able to tweak and measure performance settings starts from the beginning but attempts to provide proper understanding rather than idiot-oriented steps to follow Basically, I’m interested in how these technologies work and tend to be implemented in hardware and software rather than “here’s what to do if…” I’m interested in Computer Networking by Andrew S. Tanenbaum and I wonder if anyone else has any experience with that title. It’s expensive but I could probably loan a copy for £3 from the library or so.

  Read the article

• How to scale out OpenStreetMap data efficiently

  - by Pierre

  For over a year now, I'm running an in-house PostGIS server filled with OSM data, used for both Mapnik-based tile generation and Nominatim-based geocoding, updated with day replicates. This works pretty well. However, as usage is growing exponentially, I would like to achieve better reliability and performance by adding additional PostgreSQL servers. And I'm kind of lost. Since PostgreSQL doesn't seem to handle replication by itself, I would think about using a piede of middleware like PgPool-II to keep the servers in sync. But I'm afraid it would be nothing but necessary for this usage : very high read-to-write ratio, where all writes are done at the same exact time every day. My questions are simple : What would you do to keep these servers in sync? And, what is done for this at the OpenStreetMap Foundation, MapQuest, Mapbox or CloudMade? Thanks.

  Read the article

• sonicwall nsa 240

  - by Adam

  Hi We are looking into putting a hardware firewall into a data center to protect our rack of servers. We are using the servers for terminal services and we have 2 x 1GB connections to the Internet. We have about 50 servers supporting about 250 users which will grow very soon to 500 users. We plan to purchase 2 hardware firewalls to provide HA. Do you think the Sonicwall NSA 240 with Total Secure is a good match for this in terms of performance and protection (from spyware, virus etc?) or is there a better purchase? (Maybe a Watchguard X5 or X8?)

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• Make SoX not show output

  - by Ram Rachum

  I'm recording with SoX, and I want to make it not show output at all. When recording, it shows this output: Input File : 'default' (waveaudio) Channels : 2 Sample Rate : 48000 Precision : 16-bit Sample Encoding: 16-bit Signed Integer PCM In:0.00% 00:00:00.68 [00:00:00.00] Out:28.7k [ | ] Clip:0 I tried setting verbosity to 0, but it has no effect. (I'm guessing it's meant for messages other than this.) I don't just want to hide the output, which I could do easily; I want SoX to not generate it in the first place, for performance on a weak computer.

  Read the article

• Parity Initialization after putting in two new disks

  - by lbanz

  All my firmware is up to date on the server and the controllers. Storage crashed over the weekend. I rebooted it and it detected that I put in two new disks last week (I did check that both disk completed the rebuilding process last week). After it booted into the OS I see that it gave me an information message. After 18 hours it is at 54% so it is looking healthy. But I need to replace 5 more disk in the msa. Should I wait for this message to finish before replacing more disks? 785 Background parity initialization is currently queued or in progress on Logical Drive 1 (15.0 TB, RAID 5). If background parity initialization is queued, it will start when I/O is performed on the drive. When background parity initialization completes, the performance of the logical drive will improve.

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• How do I log file system read/writes by filename in Linux?

  - by Casey

  I'm looking for a simple method that will log file system operations. It should display the name of the file being accessed or modified. I'm familiar with powertop, and it appears this works to an extent, in so much that it show the user files that were written to. Is there any other utilities that support this feature. Some of my findings: powertop: best for write access logging, but more focused on CPU activity iotop: shows real time disk access by process, but not file name lsof: shows the open files per process, but not real time file access iostat: shows the real time I/O performance of disk/arrays but does not indicate file or process

  Read the article

• Prevent Windows 7 from unpluging External HDD

  - by marverix

  I have installed Windows 7 as my media server. I pluged in 500GB external HDD via USB. I have changed power plan to Best Performance and changed advenced power settings to never turn off HDD etc. I even yesterday wrote powershell script (create and delete folder on this disk) and I have added it to harmonogram to run every 5 minutes starting from system boot. And nothing! Disk after some time (I realy can't say when) is turning off and Windows show "Unknown Device" in Device Manager. Then only system reboot or disk reboot helps. Any ideas how to prevent Windows 7 from stopping my external HDD? Cheers!

  Read the article

• What happens when you add a Graphics card to a i7 with build in graphics (e.g. HD 4000)

  - by Matt

  I'm thinking of upgrading my computer from an AMD Phenom II X4 955BE with a AMD Radeon HD 6800 Graphics card (not integrated) to using a Intel Core i7 3770. As I have no knowledge of integrated graphics, my question is, what happens to the computing power when not using the HD4000 integrated graphics of the CPU (does it mean the CPU will run faster then it would if I relied on it?) Also what is better the CPUs inbuilt HD4000 or my Radeon Graphics card? I am mostly interested in terms of content creation: Using Adobe After Effects, 3D Rendering etc. Not too bothered about gaming performance. I will be using the spare parts of this build and older systems to make a second computer for network renders so what will be the advantages of keeping the Radeon with the current system for that?

  Read the article

• Linux servers vs Windows IIS sense of usage "free" solutions

  - by Rob

  I wonder what is the sense of using "free" open source solutions for serious webstie applications? Crawled and read many testing of servers performance and there is one conclusion: IIS seems to be the best choice for high load applicatiom. I mean cost effective. Especially this concers to Nginx PLUS and LiteSpeed Users where subscriptions paid for e.g. LoadBalacer and extra support cost a lot in fact. I'm asking then where it's "free" then or "cheap" in this case? Assuming even little higher cost of dedicated servers with Windows still seems like Windows looks cheaper. At it's basic setup Windows 2012 with IIS offer much more than std LAMP, or other NGINX config.... Maybe am I missing sth ? I mean only general case for someone who did not already started his app. I know exactly that the cheapest solution is the one someone is skilled. Has anyone done already such real costs calculation for example scenarios?

  Read the article

• How must I deal with anti-virus software on Windows 7

  - by Heather

  I know this question is looking like an easy question or not a question at all but it's not really easy question. I'm not related to security and anti-viruses and just don't trust every provided anti-virus. So first question is a real question - Is it OK (safe) to not use anti-virus at all. I know how to use firewall, usually I use only trusted connections and surfing trusted sites. My chances to get virus is really low. Even I've got a bit outdated PC and don't want to pay the performance for it. I can do monthly scans without having one installed - is it OK to be safe ? If not can you recommend a good free antivirus solution?

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• How do ulimit -n and /proc/sys/fs/file-max differ?

  - by bantic

  I notice that on a new CentOS image that I just booted up off of EC2 that the ulimit default is 1024 open files, but /proc/sys/fs/file-max is set at 761,408 and I'm wondering how these two limits work together. I'm guessing that ulimit -n is a per-user limit of number of file descriptors while /proc/sys/fs/file-max is system-wide? If that's the case, say I've logged in twice as the same user -- does each logged-in user have a 1024 limit on number of open files, or is it a limit of 1024 combined open files between each of those logged-in users? And is there much performance impact to setting your max file descriptors to a very high number, if your system isn't ever opening very many files?

  Read the article

• Using Windows 7 XP Mode for games

  - by Josefvz

  Hi all. I have Win 7 (x64) at home and I want to play some old games (specifically Lands of Lore 3, but also some others). This game does not work properly on Win 7, and there are no patches that I'm aware of to fix its issues. Can I use XP Mode to play this game (and other non Win 7 nice games), or is there a better way? I only have one PC and dual booting scares me... (so no to dual booting!) Another question: Will I have full hardware support (full use of my graphics card, etc) when I use DOSbox or a VM? I have decided to go with VirtualBox or vmware, I'll check which one gives the best performance, thanks for your input!

  Read the article

• What is the best solution for letting both Macs and PCs access digital images and videos on a networ

  - by Gertbert

  I'm looking for a simple way to share digital images and videos over a network to both Macs and PCs. I'm currently looking into three options: NAS, WD MyBook Mirror drives attached to a router, or an HP WHS product like the Data Vault. I'm looking for something easy to implement that allows for drive mirroring but also has good performance for both Macs and PCS. I've read that the HP WHS devices rebalance on their own schedules, making them useless for streaming video, and hope someone can definitively confirm or deny this as it's a dealbreaker if true. Any other suggestions are appreciated. Thanks!

  Read the article

• My Graphics Card isn't working Properly

  - by Dan

  I have just upgraded from a Sapphire AMD 6670 2gb Graphics card to a Nvidia GTX 650 ti 2gb SSC and my Windows Experiance index has gone from 6.8 to 7.7 but when playing games i am seeing no improvements i cannot play saints row three on even the lowest settings but according to many people and benchmarks on the web i should be able to play it comfortably. I want to know why this is happening to me..... I have installed the latest drivers and i have direct 10 + 11 installed I am 15 and it's my birthday today as i got it as a present but its not doing what i want also in am using a dvi cable not hdmi because i need a new one and its in the post. Is it possible that using dvi will affect performance

  Read the article

• Nexenta under KVM?

  - by Nick

  I have an Ubuntu Server running KVM. I'd like to get the benefits of ZFS so I was thinking of installing a virtual machine under KVM running Nexenta (or NexentaStor), allowing that virtual machine to have raw access to a couple of physical hard disks, and then having it share its file system with NFS so that Ubuntu can access it. I've never tried setting up KVM so that the virtual machine has access to physical drives. Does this sound feasible, and is there anything I need to watch out for? Has someone already documented something like this? Does Nexenta/ZFS function basically as well in the virtual environment as if they were running base bones? I can take a small performance hit, but I don't want it to not be as reliable because of the virtualization. Thanks.

  Read the article

< Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >