Search Results

Search found 27258 results on 1091 pages for 'installed programs'.

Page 345/1091 | < Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >

• How do I configure a new (non-OS) raid device under Windows 7?

  - by GregH

  I recently installed 3 new 1TB drives in my Windows 7 (64 bit) system. These are in addition to the 10k rpm disk that I already have running the Windows 7 OS. My intent is to create a RAID 5 volume with the 3 disks. I don't seem to have a problem configuring the bios and creating the resulting 1.9 TB RAID volume. I run in to the problem when I try booting in to Windows. I get a quick flash of a blue screen and then am prompted by windows to do a repair. It tries to repair and then reboots. This sequence lasts indefinitely. If I re-configure the bios back to non-RAID (ACHI) then windows boots fine. The strange thing is that the 1.9 TB volume I configured through the bios actually shows up in windows! Strange since the motherboard is not set up with RAID. I assume that I somehow have to install the RAID drivers from the mobo manufacturer. How do I do this? Is the reason I'm getting the blue screen a result of not having the RAID drivers installed? It's strange because I can find plenty of documentation on how to set up RAID and do a fresh install Windows on to the RAID device, but nothing on how to set up a RAID device on an already running system. Advice is appreciated.

  Read the article

• Firefox does not upgrade properly (infinite installation loop without success)

  - by Mehper C. Palavuzlar

  I've been using Firefox for a long time but I have a problem with upgrading process now. As you know, Firefox automatically checks for the latest version and downloads it, and when it is ready to be installed it starts the installation process as usual. Last month, when I clicked on "OK, install v3.6.2", the process started but couldn't be finished properly. FF gave a message like that: "Installation cannot be completed, please restart Firefox to retry". When I restarted FF, the same thing happened, and the process entered in an infinite loop. I restarted my PC and clicked on FF icon, and again the installation process began and went into the infinite loop. My solution to this problem was to download FF 3.6.2 and manually install it after killing firefox.exe. Today, FF proposed me to install v3.6.3 and again the same problem occured. I manually downloaded FF 3.6.3 and installed it successfully. Anyone experiencing this problem? In case you want to know, I did not install any new addons in the last few months, and my FF operates without problems. I'm using Windows 7 Home Pro x64.

  Read the article

• Font for Wine that supports the entire character set of the Win32 Console?

  - by Brian Campbell

  I would like to be able to display in the Wine console all characters that the Win32 console can display. I've written a small test program to print out all 8-bit characters: #include <stdio.h> int main(int argc, char *argv[]) { int i, j; for (i = 0; i <= 0xF0; i+=0x10) { for (j = i; j <= i + 0x0F; ++j) printf("%2x:%c", j, (char)j); printf("\n"); } getchar(); return 0; } Under Wine, the best I can do so far is using Andale Mono: While this is what I see on Windows Server 2008: Is there anywhere I can legally download a font that will allow me to view all of those characters under Wine? edit I've found a set of DOS fonts that includes a CP437 font, which should cover the character set I'm interested in. However, even if I install this font, wineconsole doesn't seem to recognize it. Is there any way I can get wineconsole to use this font, or convert this font to a format that wineconsole can use? Or is there any way I can extract fonts from DOSEMU for use in Wine? Oh, and I should probably mention that I'm on Mac OS X 10.6.2, installing Wine via MacPorts, using the wine-devel package. more information I have tried installing some console fonts that should cover the full character set as Mac OS X fonts (such as the NewDOS font listed above, and a font I tried converting from the fonts supplied by DOSEMU). Wine does not seem to pick up on new fonts installed in Mac OS X. Is there a way to register new fonts I've installed with Wine? Would manually editing the system.reg file that seems to contain font mappings work, or is there something else I'd need to do? bump Bounty ends soon, I'm still looking for an answer for this. Does anyone use the Wine console for complex text user interfaces?

  Read the article

• Installing Trac on Windows under Apache 2.2?

  - by Warren P

  Trac is a python-powered bug-tracking and project-management app. According to Trac's wiki, there are several options for installing Trac, a standalone server (tracd), or under a dedicated webserver using one of these options: FastCGI - Not available on windows. mod_wsgi - No version of mod_wsgi available for Apache 2.2.22 and Python 2.7.3-amd64 that actually runs on my system! mod_python - no longer recommended, as mod_python is not actively maintained anymore) CGI -should not be used, as the performance is far from optimal) That leaves me with zero ways to run Trac on Windows. Apache 2.2.22 with ModWSGI loading, crashes the Apache2.2 service on startup without any error logs. Disabling the line in the apache configuration to load mod_wsgi restores sanity. I just want an installation of Trac on windows with Authentication enabled. I am unable to get authenetication to work using basic tracd like this: tracd -p 8000 --basic-auth="c:\tmp,c:\tmp\Passwords.md5.txt,mycompany" c:\tmp\RootFolder And I am unable to get Mod_WSGI installed. I'm going to keep trying to figure out a combination that works, I suspect I should have installed 32 bit python instead of 64 bit python, to start with. Did I do wrong to install Python 64 bit 2.7.3? I tried again with all 32 bit components, and still can't get MOD_WSGI to work with apache 2.2.22. I'm going to try to compile mod_wsgi myself with Visual C++ Express 2010, but it seems to me that it ought to be easier than this to get Trac running on windows, with authentication. Is there a way to run Trac on Windows, under Apache, with authentication? The last "Trac on windows" article died in 2008, leaving only this internet archive link for "Trac on windows" setup.

  Read the article

• remove tasksel lamp-server

  - by RickyA

  I was tricked in running "sudo tasksel install lamp-server" on the wrong server (UBUNTU 10.4). Now I am stuck with a system where apache won't start because of a "Address already in use: make_sock: could not bind to address 0.0.0.0:80" error. I now want to remove this task, but documentation on that crappy tasksel says you cant use it to uninstall stuff (!!!???). My question is where can I see what packages it installed, and how can I get rid of a selection of them (apt-get?). I want to keep apache, but mysql, php and the other stuff can go... [edit] I managed to get rid of most of the lamp stack. (/var/logs/dpkg.log is usefull for recently installed packages). However it did something in a configuration somewhere, and now two apache intstances start at boottime. Killing the first one and starting a new one gets rid of the "could not bind at adress..." error. Does anyone know where the startup of the first one is configured?

  Read the article

• How to repair Mac OS X without reinstalling?

  - by RahulVyas

  I have an Intel PC. I have installed iDeneb Mac OS X in my PC. It's running fine. After that I thought about installing Snow Leopard for running the iPad SDK. So I bought a retail Snow Leopard and booted it with Rebel EFI boot loader. When I was installing Snow Leopard, at the end of installation, setup gives an error. So I restarted my PC and boot with Rebel and I saw that the Mac was there so I booted that into safe mode and Mac OS X runs. After that I installed iPad SDK. But when I try to create an application, Xcode is not responsive. It hangs when I choose new project, give it a name and save it on disk. After just as I gave name and choose save it hangs. Is there any way I can repair my Mac OS X without reinstalling? I have also been unable to boot into normal mode and also without Rebel CD. So I want to boot without Rebel CD and also want to run iPad SDK.

  Read the article

• Windows 8, IIS8 how to make PHP imagick work

  - by Laci K

  I'm new to IIS server before IIS for 6 years I used Apache 2.X and with Apache imageMagick and its PHP module imagick worked just fine even with x64 version of PHP and Apache 2.4 and imageMagick. I tried to make imagick to work with IIS8 but it wont work. I always get the typical PHP startup warning in my log PHP Startup: Unable to load dynamic library 'C:\Program Files (x86)\iis express\PHP\v5.4\ext\php_imagick.dll' - %1 is not a valid Win32 application. in Unknown on line 0 And the next thing why is IIS loading php from IIS express folder if I have php in the program files? But actually I dont care until it works :) So what I did so far I unistalled imageMagick 6.7.X 64bit version and installed the latest x86 version, tested it in command line and it worked, than I looked up on net the latest imagick DLL which was I think the 3.1.0RC2 (founded here http://www.peewit.fr/imagick/) than I copied the dll to PHP's ext folder than edited php.ini and added the imagick to the dynamic extensions after that I restarted IIS and than nothing :( I got the error which I wrote earlier. Today I installed PEAR package Installer because I read somewhere that someone made it work with it but he also mentioned, that he needed to comply wincache too. Isn't there any easier solutions to make it work? Could someone maybe write me a step by step guide how to make this work.

  Read the article

• OpenSwan (IPSEC) on Fedora 13 with Snow Leopard as a client

  - by sicn

  I recently installed OpenSwan on my Fedora 13 machine. I want to use it to connect with Mac OS X with L2TP over IPSEC, unfortunately I am already stuck on the IPSEC-negotation part. My server is running behind a NATted firewall so my external IP differs from the server's IP. The server has a fixed IP on the network and the same is almost always valid for the clients (they are usually behind a NATted firewall). I installed OpenSwan on Fedora 13 and have following configuration: config setup protostack=netkey nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=my.servers.external.ip leftprotoport=17/1701 right=%any rightprotoport=17/0 IPSEC starts fine and listens to UDP 500 and 4500. These two ports are opened in the firewall and are forwarded fine to the server. In my /etc/ipsec.secrets file I have my.servers.external.ip %any: "LongAndDifficultPassword" And finally in my sysctl.conf (the redirect-entries are there because OpenSwan was strongly protesting about send/accept_redirects being active) I have net.ipv4.ip_forward = 1 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_redirects = 0 Running "ipsec verify" gives me "all greens" (except Opportunistic Encryption Support, which is DISABLED), however, when trying to connect my Mac gives me following in the logs: Nov 1 19:30:28 macbook pppd[4904]: pppd 2.4.2 (Apple version 412.3) started by user, uid 1011 Nov 1 19:30:28 macbook pppd[4904]: L2TP connecting to server 'my.servers.ip.address' (my.servers.ip.address)... Nov 1 19:30:28 macbook pppd[4904]: IPSec connection started Nov 1 19:30:28 macbook racoon[4905]: Connecting. Nov 1 19:30:28 macbook racoon[4905]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Nov 1 19:30:31 macbook racoon[4905]: IKE Packet: transmit success. (Phase1 Retransmit). Nov 1 19:30:38: --- last message repeated 2 times --- Nov 1 19:30:38 macbook pppd[4904]: IPSec connection failed Any ideas at all?

  Read the article

• Unsigned lenny packages with aptitude safe-upgrade

  - by Liam

  I have several Debian lenny computers. Two have nearly identical sources.list files. On both, I do regular update/safe-upgrades. On one it always goes smoothly. On the other, much of the time I get the following: sudo aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages will be upgraded: krb5-clients krb5-ftpd krb5-rsh-server krb5-telnetd krb5-user libimlib2 libkadm55 libkrb53 libpng12-0 libpulse0 xpdf xpdf-common xpdf-reader 13 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 2906kB of archives. After unpacking 36.9kB will be used. Do you want to continue? [Y/n/?] WARNING: untrusted versions of the following packages will be installed! Untrusted packages could compromise your system's security. You should only proceed with the installation if you are certain that this is what you want to do. krb5-rsh-server krb5-user krb5-ftpd krb5-clients libkrb53 xpdf-reader libpng12-0 libkadm55 xpdf libpulse0 libimlib2 krb5-telnetd xpdf-common Do you want to ignore this warning and proceed anyway? To continue, enter "Yes"; to abort, enter "No": no Abort. Needless to say, I don't proceed. What is going on? How do I fix it? These are the non-comment lines in the sources.list for this computer: deb ftp://ftp.debian.org/debian/ lenny main contrib non-free deb-src ftp://ftp.debian.org/debian/ lenny main contrib deb http://security.debian.org/ lenny/updates main contrib non-free Thank you.

  Read the article

• SQL 2005 Install completly broken on laptop.

  - by ProfKaos

  My problems started when I set up an exploratory domain controller at home. During that process, I changed the name of my laptop, from 'erisia' to 'erisia-laptop', and this resulted in me losing my admin account on SQL Server 2005 on my laptop. SQL Server seems to store the machine name as part of the user name, so now my local admin account is 'erisia-laptop\brady', which SQL server didn't recognise. I thought I'd cut my losses and just re-install SQL 2005, but the first install was aborted, so I tried a complete uninstall, followed by the new install. The latter didn't work while the former worked way too well. Now every attempt at installing SQL Server 2005 SP2 on my laptop running XP SP3 ends in sadness, with MSXML6 being the cause, because it won't install on this OS version. WTF? Does anyone know what I can do to get SQL 2005 installed? It's the only full admin DB tool I have. SQL 2008 Express that installed with VS 2010 Beta 2 doesn't allow much server admin.

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• SATA HDD stuttering on reads (LED on)

  - by jdehaan

  I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

  Read the article

• Update git on mac

  - by Meltemi

  I can't remember how I installed git a while back....but now it's living in /usr/bin/git and needs to be updated. I don't care how (pre-compiled or build my own) but what I don't want is another version existing somewhere else. i vaguely remember curl(ing) down the source & compiling it. but not positive. anyway, what's the easiest way to keep Git up-to-date under Mac OS X? Side question: I'm not that familiar with git. once it's installed is it ENTIRELY contained within its directory? so, in my case, everything about git on my machine (excluding the actual code repositories of course) is in /usr/bin/git/ ? If so then can I just move git around with a simple mv -R /usr/bin/git /opt/git? Then update my $PATH and everything should work as before? if so then i supposed i could just install again by any method and to any directory...and then move the new one into /usr/bin replacing the old version?!? Or is this bad?

  Read the article

• FFMPEG: how to add watermark to video?

  - by DocWiki

  My Platform: Ubuntu 10.10 + FFMPEG 0.5.3(I installed ffmpeg from source) I try to add Watermark to a .MOV video with FFMPEG 0.5.3 imlib2.so (Please note FFMPEG 0.6+ dont support imlib2.so, so I use ffmpeg 0.5.3) Here is my code: ffmpeg -sameq -i example.mov -vhook '/usr/local/lib/vhook/imlib2.so -x 0 -y 0 -i /var/www/files/watermark.png' newexample.mov Here is the output: FFmpeg version 0.5.3, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-avfilter --enable-filter=movie --enable-avfilter-lavf libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 built on Jul 3 2011 12:05:08, gcc: 4.4.5 Seems stream 1 codec frame rate differs from container frame rate: 59.94 (5994/100) - 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'example.mov': Duration: 00:03:14.06, start: 0.000000, bitrate: 3350 kb/s Stream #0.0(eng): Audio: aac, 48000 Hz, stereo, s16 Stream #0.1(eng): Video: h264, yuv420p, 1150x647, 29.97 tbr, 29.97 tbn, 59.94 tbc Output #0, mov, to 'newexample.mov': Stream #0.0(eng): Video: mpeg4, yuv420p, 1150x647, q=2-31, 200 kb/s, 90k tbn, 29.97 tbc Stream #0.1(eng): Audio: 0x0000, 48000 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 - #0.0 Stream #0.0 - #0.1 Unsupported codec for output stream #0.1 What could be the possible problem? Is that AAC or H264 that is not supported? I installed libavcodec-extra-52, linfaac, libfaad and etc. but the error is the same. Do I have to install following this instruction? HOWTO: Install and use the latest FFmpeg and x264 or there is a simpler solution?

  Read the article

• Postfix not working

  - by user1488723

  A while ago I installed the postfix mail server on my ubuntu 10.04 VPS. At the time it was working good but now it's just stopped working. I was trying to enable SASL authentification and somewhere it must have went really wrong. I've studied the postfix main.cf and done everything in an orderly fashion to ensure that it is nothing wrong. I also have Dovecot installed and configured dovecot.conf to run with Postfix. If I try to do telnet localhost 25 while logged in on the server I just get: Connection closed by foreign host. If I try to do telnet mail.example.com 25 "from the outside" I get: telnet: Unable to connect to remote host: No route to host And when I check the server log after the failed attempts I see this: Jun 28 15:49:31 msv postfix/smtpd[11839]: initializing the server-side TLS engine Jun 28 15:49:31 msv postfix/smtpd[11839]: connect from localhost.localdomain[127.0.0.1] Jun 28 15:49:31 msv postfix/smtpd[11839]: warning: SASL: Connect to /var/spool/postfix/private/auth failed: Connection refused Jun 28 15:49:31 msv postfix/smtpd[11839]: fatal: no SASL authentication mechanisms Jun 28 15:49:32 msv postfix/master[11598]: warning: process /usr/lib/postfix/smtpd pid 11839 exit status 1 Jun 28 15:49:32 msv postfix/master[11598]: warning: /usr/lib/postfix/smtpd: bad command startup -- throttling main.cf file looks like this: smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no append_dot_mydomain = no delay_warning_time = 4h myhostname = mail.example.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mydomain = example.com myorigin = $mydomain mydestination = $mydomain relayhost = mynetworks = 127.0.0.1 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_use_tls = yes smtpd_tls_loglevel = 2 smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_sasl_auth_enable = yes smtpd_client_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks smtpd_recipient_restrictions = permit_sasl_authenticated, reject_unauth_destination broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = /var/spool/postfix/private/auth smtpd_sasl_security_options = noanonymous Dovecot.conf file looks like this: protocols = imap imaps disable_plaintext_auth = no log_timestamp = "%b %d %H:%M:%S " ssl = yes ssl_cert_file = /etc/postfix/ssl/smtpd.crt ssl_key_file = /etc/postfix/ssl/smtpd.key mail_location = maildir:~/mail mail_access_groups = mail auth_username_chars = abcdefghijklmnopqrstuvwxyz protocol imap { imap_client_workarounds = delay-newmail tb-extra-mailbox-sep } auth default { mechanisms = plain login passdb pam { } userdb passwd { } socket listen { client { path = /var/spool/postfix/private/auth user = postfix group = postfix mode = 0660 } } }

  Read the article

• Terminal Server 2008: Remote App Issue

  - by JohnyD

  I have a FoxPro 2.6 (16-bit) application that I've installed on a Win2008 (32-bit) Terminal Server. I then created a Remote App from it. It works fine. The problem is that within this FoxPro application it calls out to a .Net application. I have the proper .Net Framework installed on the server (2.0) and I have run the code access security policy tool (caspol.exe). However, when I launch the .Net app from within the FoxPro application I get the following error: Description: Stopped working Problem signature: Problem Event Name: CLR20r3 Problem Signature 01: vector.exe Problem Signature 02: 1.0.0.3 Problem Signature 03: 48b579f2 Problem Signature 04: vector Problem Signature 05: 1.0.0.3 Problem Signature 06: 48b579f2 Problem Signature 07: f Problem Signature 08: 57 Problem Signature 09: System.Security.Security OS Version: 6.0.6001.2.1.0.18.10 Locale ID: 1033 Vector.exe is our .Net application. In fact, it's an in-between application that checks to ensure you have the latest version. When it's done it calls out to another .Net executable. Does anyone believe this should be a problem? Thanks in advance.

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• Ubuntu: unattended-upgrades from a local package archive

  - by Novelocrat

  I have a local apt archive with a bunch of packages I built in it. The Packages and Release file are generated by apt-ftparchive. The Release file looks like Date: Thu, 06 May 2010 23:04:33 UTC Label: PPL Origin: PPL Suite: ppl MD5Sum: ebec3527ebc8351468b2ef8796c19855 37325 Packages d41d8cd98f00b204e9800998ecf8427e 0 Release SHA1: a0593b663d77fde88ee35b56ae1f3c17801cfe99 37325 Packages da39a3ee5e6b4b0d3255bfef95601890afd80709 0 Release SHA256: dd73a02846aee111cac58a869c6bf650886632ba82c2172ffddd81aa4429981c 37325 Packages e3b0c44298fc1c149afbf4c8996fb92427ae41e4649b934ca495991b7852b855 0 Release I'm using unattended-upgrades to keep the machines in the lab up to date on security and bug fixes, but I'm finding that it doesn't pull from my local archive. The configuration file for it looks like // Automaticall upgrade packages from these (origin, archive) pairs Unattended-Upgrade::Allowed-Origins { "Ubuntu hardy-security"; "Ubuntu hardy-updates"; "PPL ppl"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. The package 'mailx' // must be installed or anything that provides /usr/bin/mail. //Unattended-Upgrade::Mail "root@localhost"; Yet, when I run sudo unattended-upgrade on one of these machines, newer package versions don't get installed. Can anyone point out what I'm getting wrong?

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• Uninstall Perl 5.10 and Install 5.8 on Ubuntu 10.04

  - by user48848

  I was using Ubuntu 8.04 with installed Perl 5.8.8. I had installed Bugzilla 3.4.4 with some custom scripts and it was working fine. I had to upgrade Ubuntu from 8.04 to 10.04 and automatically Perl is also upgraded from Perl 5.8 to 5.10. Now, accessing Bugzilla displays an error message related to Perl module. While trying to run checksetup.pl, I am getting the following error message: root@cvsnew:/var/www/bugzilla-3.4# perl checksetup.pl * This is Bugzilla 3.4.3 on perl 5.10.1 * Running on Linux 2.6.32-24-generic-pae #39-Ubuntu SMP Wed Jul 28 07:39:26 UTC 2010 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.48 perl: symbol lookup error: lib/i486-linux-gnu-thread-multi/auto/Digest/SHA/SHA.so: undefined symbol: Perl_Tstack_sp_ptr Accessing Bugzilla throws : "500 Internal Server Error". I explored this issue and found that this issue has come up because upgrading Ubuntu upgrades Perl 5.8 to 5.10 automatically. It seems like Perl 5.10.1 isn't binary compatible with the previous. Now, I want to uninstall Perl 5.10.1 and Install Perl 5.8.8 on my Ubuntu 10.04 box. I will appreciate if someone has already done that or share the required steps/commands to do it.

  Read the article

• Mustek 1200 CP driver SFC4.SYS bluescreens with BAD_POOL_HEADER

  - by Slink84

  I have Windows XP SP2. Recently it started bluescreening right after starting up with 'BAD_POOL_HEADER', 0x00000019 error caused by SFC4.SYS driver. After googling for a while I've found out that this is my Mustek's 1200 CP scanner driver. Booting in safe mode and uninstalling it solved the problem... And created another one: now I can't use my scanner. The weird thing is, that it has been working for a while on this PC without any problems. It all started suddenly, and I can't remember installing anything that might have affected it. Reverting to several earlier system restore points didn't help. I've tried re-installing it from the Mustek website, just in case if my copy got corrupted or infected by a virus, but it did not help - it still bluescreens. Also, I've installed Avast and scanned my PC - there were no viruses found. If anyone had such a problem before or has an idea what might have caused it, please help. ED: @Michael Todd: ...try installing on another PC... I've installed it on my friends PC. He has the same OS version, with the latest updates just like mine (he wasn't too happy, even after I've assured him that it is easy to fix by uninstalling that driver :] ). It worked fine - no bluescreens or whatsoever. So I think I've narrowed it down to either BIOS settings, or some wicked driver conflict. Next thing I'm going to try is to re-install XP, or install windows 7. I'm not too happy with a prospect of mucking about with BIOS settings...

  Read the article

• Ubuntu: how to get audio to work in both Spotify (under Wine) and Flash (in Firefox)?

  - by Jonik

  I'm running Spotify on Linux using Wine. Sound worked great (even though the sound test in winecfg failed!), until I installed alsa-oss package yesterday to get Flash sound working in Firefox. Now Spotify says: "There is a problem with your sound card. Spotify can't play music." So the question is, how to get the sound in Spotify working again, so that it also keeps working in Flash & Firefox? Tweak some ALSA settings? Spotify settings? Add/remove some packages? By the way, curiously, now that sound doesn't work in Spotify, winecfg's "Test Sound" does work! This is Ubuntu 8.04 (Hardy). Sound card / driver is probably an integrated AC'97. Please mention if any additional information about the system is needed! Update: I have Flash 10 installed (outside the packaging system, using $MOZ_PLUGIN_PATH env variable), but also had Flash 9 from flashplugin-nonfree package - and the earlier version was being used by Firefox! Based on what Mike Arthur said about Flash and alsa-oss, I removed the older Flash (flashplugin-nonfree package) and alsa-oss - and Flash sound still works, which is nice. But for some reason Spotify still doesn't play sound, even though things should now be like they were originally... Update 2: Got it working, all smoothly, finally.

  Read the article

• IIS 7.5 FTP Service crashes after installation of Advanced Logging 1.0 Module

  - by Jeremy

  I've recently been tasked with setting up two new productions servers for an ASP.Net application. The servers sit behind a F5 Load Balancer, which in turn forwards the end users IP address forward via the standard X_Forwarded_For HTTP Header. All of the reading that I have done suggests that I need to install the IIS Advanced Logging Module in order to take advantage of the X_Forwarded_For HTTP Header. Some quick background: Both of the web servers are Windows 2008 R2 Standard (x64), with IIS 7.5 installed and configured. The FTP Role has also been installed, configured and is operational. The Issue After installing the IIS Advanced Logging module via the Web Platform Installer, I noticed the following Error in the Event Viewer: The FTP Service encountered an error trying to read configuration data from file \?\C:\Windows\system32\inetsrv\config\applicationHost.config, line number 374. The error message is: Unrecognized element 'advancedLogging' Trying to connect over FTP to either of the web servers results in a 530. I've spent 2 hours scouring Google trying to find a solution, short of uninstalling the Advanced Logging Module. As far as I can tell, there is no way to turn off Advanced Logging on a site per site basis. Help would be appreciated.

  Read the article

• Integration of SharePoint 2010 with TFS2010

  - by Kabir Rao

  We have performed following steps as of now- Install TFS2010 10.0.30319.1 (RTM) on Windows Server 2008 R2 Enterprise(app tier) SQL 2008 SP1 with Cumulative update 2 on Windows Server 2008 R2 Enterprise(data tier) Reporting Service is installed on app tier. After this installation worked fine we installed SharePoint 2010 on app tier. After installation we followed http://blogs.msdn.com/b/team_foundation/archive/2010/03/06/configuring-sharepoint-server-2010-beta-for-dashboard-compatibility-with-tfs-2010-beta2-rc.aspx for configuration. We are not able to perform the last step described in the link as following error occured- TF249063: The following Web service is not available: http://apptier:31254/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. The underlying error is: The remote server returned an error: (404) Not Found.. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://apptier:31254. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. We have also noticed that Document Folder in Team project also have red x. Please help. Thanks upfront.

  Read the article

• Win 2008 R2 - copying TO disk is very slow, copying FROM is more or less okay

  - by avs099

  I have Windows 2008 R2 SP1 with 4 identical SATA disks (Seagate Barracude 7200) in RAID 5 array. It has 4Gb of memory; all recent updates are installed. Problem: when I copy large file from one folder to another, I get about 10MB/s average speed. When I read this file from network share via 1Gbps connection - I get about 25-30 MB/s. Both numbers seems to be low for me - but specifically I'm very frustrated with low write speed. there is no antivirus, no hyper-v, it's just a fileserver - i when i do my tests nobody else reads/write from it (we have only 4 people in a team, so I'm sure). Not sure if that matters, but there is only 1 logic disk "C" with all available space (1400 GB). I'm not an admin at all, so I have no idea where to look and what other information to provide. I did run performance monitor with "% idle time", "avg bytes read", "avg byte write" - here is the screenshot: I'm not sure why there are such obvious spikes. Any idea? Please let me know if you need me to provide more information - what counters should I check, etc. I'm very eager to get this solved. Thank you. UPDATE: we have another Windows 2008 R2 SP1 server with 2 RAID1 arrays - one is disk C (where windows is installed, another one is disk E). It is running Hyper-V and does not have antivirus. I noticed the following behavior when I copy large file (few GBs): C - C: about 50MB/sec C - E: about 55MB/sec E - E: 8MB/sec!!! E - C: 8MB/sec!!! what could cause this?? E drive is RAID1 array from same Seagate Barracuda 1TB drives..

  Read the article

< Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >