Search Results

Search found 18533 results on 742 pages for 'intel visual fortran'.

Page 347/742 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• (manually configured) kernel update leaves wireless in a mess

  - by Mala

  I recently upgraded my kernel from 2.6.31-gentoo-r6 to 2.6.32-gentoo-r7. In both cases, I configured everything manually. However, since the upgrade, my wireless card appears to be on the fritz. It will connect to networks just fine, and remain connected, but can only access the internet (and other hosts on the network) for about 3 seconds after connecting. Reconnecting to the network appears to fix the problem... for another 3 seconds or so. The problem is "solved" by booting into the older kernel. The relevant lspci entry is 02:00.0 Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection I'm pretty sure I have the correct drivers enabled in the kernel Device Drivers ---> Network device support ---> Wireless LAN (IEEE 802.11) ---> <*> Intel Wireless Wifi [*] Enable LED support in iwlagn and iwl3945 drivers [*] Enable Spectrum Measurement in iwlagn driver [*] Enable full debugging output in iwlagn and iwl3945 drivers <*> Intel Wireless WiFi Next Gen AGN (iwlagn) [*] Intel Wireless WiFi 4965AGN [*] Intel Wireless WiFi 5000AGN; Intel WiFi Link 1000, 6000, and 6050 Series I tried with the other intel drivers enabled as well (iwl3945) and no difference. Is there something stupid I'm missing? Is there something I have to recompile after upgrading the kernel (a la nvidia)? Thanks Mala

  Read the article

• Any program to help me check whether an ethernet channel can support full-length VLAN packet?

  - by Jimm Chen

  Sometimes, I have to face such a situation that I need to quickly and explicitly know whether a full length VLAN packet can traverse between two RJ45 ports. Yes, I mean 802.1Q ethernet frame with Etype=81 00 (diagram below). What I can do now is: Get two Windows PCs, for each PC, intall Intel Gigabit NIC and Intel specific driver to create a virtual NIC, with VLAN ID=3 assigned. Then connect the two PCs to each of the two RJ45 port. Finally execute ping to generate a full-length ethernet packet. ping -f -l 1472 <dest-IP> This way, I can be sure that the sent packet has the maximum "IP data payload" of 1500 bytes(8 bytes of ICMP header and 1472 bytes of ICMP data). If the ping gets reply, I know that the ethernet channel support full-length VLAN packet. From my experiment, some home switch or broad band routers(e.g. Linksys WRT54G) does not support full-length VLAN packet switching, so only ping -f -l 1468 succeeds. You see, I have to use an expensive Intel NIC to carry on that test, quite inconvenient. You know, for most laptop today, they do not equip an Intel NIC, and, even it is an Intel NIC, Intel VLAN driver, Intel has limitations on the models on which VLAN driver can be installed. So, my question is: Is there a small program that can let me send a full-length VLAN packet without installing a dedicated VLAN driver? Or better, the program has a stock feature that does the very job for my situation. Windows programs preferred, Linux solution welcome. Simpler the program, the better. Thank you.

  Read the article

• CodePlex Daily Summary for Sunday, November 04, 2012

  CodePlex Daily Summary for Sunday, November 04, 2012Popular ReleasesZXMAK2: Version 2.6.8.4: fix tape autostop & tape iconProDinner - ASP.NET MVC Sample (EF4.4, N-Tier, jQuery): 8: update to ASP.net MVC Awesome 3.0 udpate to EntityFramework 4.4 update to MVC 4 added dinners grid on homepageASP.net MVC Awesome - jQuery Ajax Helpers: 3.0: added Grid helper added XML Documentation added textbox helper added Client Side API for AjaxList removed .SearchButton from AjaxList AjaxForm and Confirm helpers have been merged into the Form helper optimized html output for AjaxDropdown, AjaxList, Autocomplete works on MVC 3 and 4BlogEngine.NET: BlogEngine.NET 2.7: Cheap ASP.NET Hosting - $4.95/Month - Click Here!! Click Here for More Info Cheap ASP.NET Hosting - $4.95/Month - Click Here! If you want to set up and start using BlogEngine.NET right away, you should download the Web project. If you want to extend or modify BlogEngine.NET, you should download the source code. If you are upgrading from a previous version of BlogEngine.NET, please take a look at the Upgrading to BlogEngine.NET 2.7 instructions. If you looking for Web Application Project, ...Launchbar: Launchbar 4.2.2.0: This release is the first step in cleaning up the code and using all the latest features of .NET 4.5 Changes 4.2.2 (2012-11-02) Improved handling of left clicks 4.1.0 (2012-10-17) Removed tray icon Assembly renamed and signed with strong name Note When you upgrade, Launchbar will start with the default settings. You can import your previous settings by following these steps: Run Launchbar and just save the settings without configuring anything Shutdown Launchbar Go to the folder %LOCA...CommonLibrary.NET: CommonLibrary.NET 0.9.8.8: Releases notes for FluentScript located at http://fluentscript.codeplex.com/wikipage?title=Release%20Notes&referringTitle=Documentation Fluentscript - 0.9.8.8 - Final ReleaseApplication: FluentScript Version: 0.9.8.8 Build: 0.9.8.8 Changeset: 77368 ( CommonLibrary.NET ) Release date: November 2nd, 2012 Binaries: CommonLibrary.dll Namespace: ComLib.Lang Project site: http://fluentscript.codeplex.com/ Download: http://commonlibrarynet.codeplex.com/releases/view/90426 Source code: http://common...Mouse Jiggler: MouseJiggle-1.3: This adds the much-requested minimize-to-tray feature to Mouse Jiggler.Umbraco CMS: Umbraco 4.10.0 Release Candidate: This is a Release Candidate, which means that if we do not find any major issues in the next week, we will release this version as the final release of 4.10.0 on November 9th, 2012. The documentation for the MVC bits still lives in the Github version of the docs for now and will be updated on our.umbraco.org with the final release of 4.10.0. Browse the documentation here: https://github.com/umbraco/Umbraco4Docs/tree/4.8.0/Documentation/Reference/Mvc If you want to do only MVC then make sur...Skype Auto Recorder: SkypeAutoRecorder 1.3.4: New icon and images. Reworked settings window. Implemented high-quality sound encoding. Implemented a possibility to produce stereo records. Added buttons with system-wide hot keys for manual starting and canceling of recording. Added buttons for opening folder with records. Added Help button. Fixed an issue when recording is continuing after call end. Fixed an issue when recording doesn't start. Fixed several bugs and improved stability. Major refactoring and optimization...Access 2010 Application Platform - Build Your Own Database: Application Platform - 0.0.2: Release 0.0.2 Created two new users. One belongs to the Administrators group and the other to the Public group. User: admin Pass: admin User: guest Pass: guest Initial Release This is the first version of the database. At the moment is all contained in one file to make development easier, but the obvious idea would be to split it into Front and Back End for a production version of the tool. The features it contains at the moment are the "Core" features.Python Tools for Visual Studio: Python Tools for Visual Studio 1.5: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, etc. support. For a quick overview of the general IDE experience, please watch this video There are a number of exciting improvement in this release comp...mangopollo: Mangopollo 1.1: New classes : CycleTileData, IconicTileData, FlipTileData to mimic Windows Phone 8 API,BCF.Net: BCF.Net: BCF.Net-20121024 source codeAssaultCube Reloaded: 2.5.5: Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we try to package for those OSes. Try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compile your own for Linux (source included) Changelog: Fixed potential bot bugs: Map change, OpenAL...DirectX Tool Kit: October 30, 2012 (add WP8 support): October 30, 2012 Added project files for Windows Phone 8MCEBuddy 2.x: MCEBuddy 2.3.6: Changelog for 2.3.6 (32bit and 64bit) 1. Fixed a bug in multichannel audio conversion failure. AAC does not support 6 channel audio, MCEBuddy now checks for it and force the output to 2 channel if AAC codec is specified 2. Fixed a bug in Original Broadcast Date and Time. Original Broadcast Date and Time is reported in UTC timezone in WTV metadata. TVDB and MovieDB dates are reported in network timezone. It is assumed the video is recorded and converted on the same machine, i.e. local timezone...MVVM Light Toolkit: MVVM Light Toolkit V4.1 for Visual Studio 2012: This version only supports Visual Studio 2012 (and all Express editions too). If you use Visual Studio 2010, please stay tuned, we will publish an update in a few days with support for VS10. V4.1 supports: Windows Phone 8 Windows 8 (Windows RT) Silverlight 5 Silverlight 4 WPF 4.5 WPF 4 WPF 3.5 And the following development environments: Visual Studio 2012 (Pro, Premium, Ultimate) Visual Studio 2012 Express for Windows 8 Visual Studio 2012 Express for Windows Phone 8 Visual...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.73: Fix issue in Discussion #401101 (unreferenced var in a for-in statement was getting removed). add the grouping operator to the parsed output so that unminified parsed code is closer to the original. Will still strip unneeded parens later, if minifying. more cleaning of references as they are minified out of the code.RiP-Ripper & PG-Ripper: PG-Ripper 1.4.03: changes NEW: Added Support for the phun.org forum FIXED: Kitty-Kats new Forum UrlLiberty: v3.4.0.1 Release 28th October 2012: Change Log -Fixed -H4 Fixed the save verification screen showing incorrect mission and difficulty information for some saves -H4 Hopefully fixed the issue where progress did not save between missions and saves would not revert correctly -H3 Fixed crashes that occurred when trying to load player information -Proper exception dialogs will now show in place of crashesNew ProjectsAzure Storage Extensions For Storage Client V2.0: This library add LINQ syntax to the method Where on TableQuery<T> This support actually Windows Azure Storage Library V2.0BekkGitTfsDemo: A demo project for a speech on git-tfs.Booky: Booky is a utility bookmarking service which allows you to manage, share and find bookmarks to ultimately store bookmarks online for later use.BSA.Net: BSA.Net bzureC# to C++/CX Converter: Gives you the power of C++ at a cost of the simplicity of C#.Cloud Clipboard Sync: Share the clipboard content via cloud (ex. Dropbox).CricketDataMining: Btech Project on Cricket Data MiningCthulhu Invaders: Estudy project about design patternsDALHelper: Connect to your SQL Server database easily, efficiently, writing minimal code. Dwarf Fortress 2010 Backup Assistant: (Inspired by Minecraft Backup Assistant - http://minecraftbackup.codeplex.com/) Allows quick and easy backup/management of your DF savegames. Planned Features: * Rename saves and autosaves * Backup to zip/7-zip with metadata * Restore backupsInmobiliaria: Proyecto de nosotrosInventário com Código de Barras para Windows CE / Mobile: Aplicativo para inventário de produtos com código de barras. Executa em coletores de dados Windows CE ou Mobile.JQuery MVC in ASP.Net WebForms: The purpose of this project is to try and strip back a lot of the "bloat" in asp.net, use jquery and to build effective MVC in to WebFormsMar3ek's Download Manager 2: Mar3ek's Download Manager 2 - a simple, yet powerful, download manager for windows.Martian Shrimp: A small, simple and modular game making framework for modern browsers.MOJ: Moj is program created to help users organize and browse their virtual movie colectionNetFluid Starter Kit: NetFluid sample collection. Including : - Wallen garden controller - JSON RPC - Background thread web page - Dynamic image generation www.netfluid.orgO Library: The O Library is a SQL Framework to use with SQL Server 2008 & 2012 that enables developer to add a .Net feeling to their T-SQL code.Scanner With WIA2.0: warp implement WIA 2.0 with c#Simplify Workflow: A set of custom activities and templates extending Windows Workflow Foundation to simplify the development process for BPM or Workflow application.T4 C# Constructor Generator: T4 C# Constructor Generator is a T4 template for Visual Studio C# projects that lowers the overhead of the C# compiler by generating constructors.Unity.Mvc.Wcf: Removes the cross-cutting concern of managing WCF service clients used by your MVC controllers.WorkflowCode - Workflow in a Code framework: Intended to use by developers. As useful and simple as possible. It is the Workflow framework for a fast and readable code. With samples and tips.XNeon Netmedia Player: A Media Player, Social Networking Notifier and Internet Browser from the Founder of Aza DOSXooFoo: This project intends sharing tools for the XOOPS communityXoops France: Publications Xoops francophones (traductions noyau xoops, documentations, modules françisés, thèmes, plugin smarty, hacks, ...)Yasher (Yet Another Hasher): Compute hash of files or text. Supported algorithms : * MD5 * SHA1 * SHA256 * SHA384 * SHA512 * RIPEMD160

  Read the article

• CodePlex Daily Summary for Monday, January 03, 2011

  CodePlex Daily Summary for Monday, January 03, 2011Popular ReleasesStyleCop for ReSharper: StyleCop for ReSharper 5.1.14977.000: Prerequisites: ============== o Visual Studio 2008 / Visual Studio 2010 o ReSharper 5.1.1753.4 o StyleCop 4.4.1.2 Preview This release adds no new features, has bug fixes around performance and unhandled errors reported on YouTrack.Morphine: Morphine Alpha Build 30: - Optimization - Some fixes with playlists - Added kinetic scrolling to tracklist view - Updated animations - Added controls to tracklist view Media opens by clicking "No media" or song title now.BloodSim: BloodSim - 1.3.1.0: - Restructured simulation log back end to something less stupid to drastically reduce simulation time and memory usage - Removed a debug log entry that was left over from testing of 1.3.0.0 - Fixed a rounding and calculation error with Haste rating - Added option for Rune of SwordshatteringDbDocument: DbDoc Initial Version: DbDoc Initial versionUltimateJB: UltimateJB 2.03 PL3 KAKAROTO: Voici une version attendu avec impatience pour beaucoup : - La version PL3 KAKAROTO intégre ses dernières modification et intégre maintenant le firmware 2.43 !!! Conclusion : - ultimateJB DEFAULT => Pas de spoof mais disponible pour les PS3 suivantes : 3.41_kiosk 3.41 3.40 3.30 3.21 3.15 3.10 3.01 2.76 2.70 2.60 2.53 2.43ASP .NET MVC CMS (Content Management System): Atomic CMS 2.1.2: Atomic CMS 2.1.2 release notes Atomic CMS installation guide Kind Of Magic MSBuild Task: Beta 4: Update to keep up with latest bug fixes. To those who don't like Magic/NoMagic attributes, you may change these names in KindOfMagic.targets file: Change this line: <MagicTask Assembly="@(IntermediateAssembly)" References="@(ReferencePath)"/> to something like this: <MagicTask Assembly="@(IntermediateAssembly)" References="@(ReferencePath)" MagicAttribute="MyMagicAttribute" NoMagicAttribute="MyNoMagicAttribute"/>N2 CMS: 2.1: N2 is a lightweight CMS framework for ASP.NET. It helps you build great web sites that anyone can update. Major Changes Support for auto-implemented properties ({get;set;}, based on contribution by And Poulsen) All-round improvements and bugfixes File manager improvements (multiple file upload, resize images to fit) New image gallery Infinite scroll paging on news Content templates First time with N2? Try the demo site Download one of the template packs (above) and open the proj...Wii Backup Fusion: Wii Backup Fusion 1.0: - Norwegian translation - French translation - German translation - WBFS dump for analysis - Scalable full HQ cover - Support for log file - Load game images improved - Support for image splitting - Diff for images after transfer - Support for scrubbing modes - Search functionality for log - Recurse depth for Files/Load - Show progress while downloading game cover - Supports more databases for cover download - Game cover loading routines improvedAutoLoL: AutoLoL v1.5.1: Fix: Fixed a bug where pressing Save As would not select the Mastery Directory by default Unexpected errors are now always reported to the user before closing AutoLoL down.* Extracted champion data to Data directory** Added disclaimer to notify users this application has nothing to do with Riot Games Inc. Updated Codeplex image * An error report will be shown to the user which can help the developers to find out what caused the error, this should improve support ** We are working on ...Random password generator written in F#.: VS 2010 solution + exe: Download a VS 2010 solution (unzip before opening) or a ready to go exe.TortoiseHg: TortoiseHg 1.1.8: TortoiseHg 1.1.8 is a minor bug fix release, with minor improvementsBlogEngine.NET: BlogEngine.NET 2.0: Get DotNetBlogEngine for 3 Months Free! Click Here for More Info 3 Months FREE – BlogEngine.NET Hosting – Click Here! If you want to set up and start using BlogEngine.NET right away, you should download the Web project. If you want to extend or modify BlogEngine.NET, you should download the source code. If you are upgrading from a previous version of BlogEngine.NET, please take a look at the Upgrading to BlogEngine.NET 2.0 instructions. To get started, be sure to check out our installatio...EnhSim: EnhSim 2.2.8 ALPHA: 2.2.8 ALPHAThis release supports WoW patch 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 Rebuilt Feral Spir...Free Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts v3.6.6 Released: Hi, Today we are releasing final version of Visifire, v3.6.6 with the following new feature: * TextDecorations property is implemented in Title for Chart. * TitleTextDecorations property is implemented in Axis. * MinPointHeight property is now applicable for Column and Bar Charts. Also this release includes few bug fixes: * ToolTipText property of DataSeries was not getting applied from Style. * Chart threw exception if IndicatorEnabled property was set to true and Too...StyleCop Compliant Visual Studio Code Snippets: Visual Studio Code Snippets - January 2011: StyleCop Compliant Visual Studio Code Snippets Visual Studio 2010 provides C# developers with 38 code snippets, enhancing developer productivty and increasing the consistency of the code. Within this project the original code snippets have been refactored to provide StyleCop compliant versions of the original code snippets while also adding many new code snippets. Within the January 2011 release you'll find 82 code snippets to make you more productive and the code you write more consistent!...WPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.2: Version: 2.0.0.2 (Milestone 2): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ...Cosmos (C# Open Source Managed Operating System): 71406: This is the second release supporting the full line of Visual Studio 2010 editions. Changes since release 71246 include: Debug info is now stored in a single .cpdb file (which is a Firebird database) Keyboard input works now (using Console.ReadLine) Console colors work (using Console.ForegroundColor and .BackgroundColor)Paint.NET PSD Plugin: 1.6.0: Handling of layer masks has been greatly improved. Improved reliability. Many PSD files that previously loaded in as garbage will now load in correctly. Parallelized loading. PSD files containing layer masks will load in a bit quicker thanks to the removal of the sequential bottleneck. Hidden layers are no longer made visible on save. Many thanks to the users who helped expose the layer masks problem: Rob Horowitz, M_Lyons10. Please keep sending in those bug reports and PSD repro files!Facebook C# SDK: 4.1.1: From 4.1.1 Release: Authentication bug fix caused by facebook change (error with redirects in Safari) Authenticator fix, always returning true From 4.1.0 Release Lots of bug fixes Removed Dynamic Runtime Language dependencies from non-dynamic platforms. Samples included in release for ASP.NET, MVC, Silverlight, Windows Phone 7, WPF, WinForms, and one Visual Basic Sample Changed internal serialization to use Json.net BREAKING CHANGE: Canvas Session is no longer supported. Use Signed...New ProjectsAndroid Battery Indicator: Small widget that shows the battery life as a percentageBudget: A personal exploration into C#. A quickly thrown together project that allows you to track expenses by week. MS Access back end.Cafeteria Dotnetnuke Module: Simple Dotnetnuke Module about Managing Cafeteria. This module was applied at Ho Chi Minh City International University Portal Website.E Book Database & Organizer: This Is a project to organize ebooks and retrive information about them very fast.Later a free e-library software may be developed based on this project. This project mainly developed with visual C#2008express edition.It also can compiled by mono. It use SQLite as database. GrowlWebBridge: Using c# Growl connector library, accept notification parameters via querystring and fire off to Growl. I'm personally using it to have my Vera 2 (www.micasaverde.com) send growls when things happen.JakoPiste: N/AJAudit: Static analysis for java programs. Helps audit java code. Reports possible code improvements. 100% C#.Morphine: Morphine is a nice WPF media player with Android Honeycomb interface.NUnit test template for VS2010 Express MVC 2: This is an attempt to create a set of template of NUnit (a test framework) for MVC 2 in Visual Studio 2010 Express.Orchard Image Field Module: Orchard Image Field Module adds a new Image editor to content type management. PDB2MOBI batch convert: Converts PDB files to MOBI format in batch. Used primary to convert large PDB libraries for Kindle.Random password generator written in F#.: A password generator that creates random and strong passwords. It's developed in F#. Robots Routing using Swarm Intelligence: A project to simulate and test a multiagent algorithm for finding multiple noisy radiation Sources with spatial and communication constraints with an emulated environment with different parameters and conditions. sanmei: sanmeiServer DateTime: Server DateTime renders the date and time from the server and make it active using javascript. It is in Military Time Format.Windows K: Microsoft Imagine Cup 2011 Project

  Read the article

• CodePlex Daily Summary for Thursday, August 30, 2012

  CodePlex Daily Summary for Thursday, August 30, 2012Popular ReleasesCoevery - Free CRM: Coevery 1.0: This is the first alpha release of Coevery.ExpressProfiler: Initial release of ExpressProfiler v1.2: This is initial release of ExpressProfilerNabu Library: 2012-08-29, 14: .Net Framework 4.0, .Net Framework 4.5 Debug and Release builds.Math.NET Numerics: Math.NET Numerics v2.2.1: Major linear algebra rework since v2.1, now available on Codeplex as well (previous versions were only available via NuGet). Since v2.2.0: Student-T density more robust for very large degrees of freedom Sparse Kronecker product much more efficient (now leverages sparsity) Direct access to raw matrix storage implementations for advanced extensibility Now also separate package for signed core library with a strong name (we dropped strong names in v2.2.0) Also available as NuGet packages...Microsoft SQL Server Product Samples: Database: AdventureWorks Databases – 2012, 2008R2 and 2008: About this release This release consolidates AdventureWorks databases for SQL Server 2012, 2008R2 and 2008 versions to one page. Each zip file contains an mdf database file and ldf log file. This should make it easier to find and download AdventureWorks databases since all OLTP versions are on one page. There are no database schema changes. For each release of the product, there is a light-weight and full version of the AdventureWorks sample database. The light-weight version is denoted by ...ImageServer: v1.1: This is the first version releasedChristoc's DotNetNuke Module Development Template: DotNetNuke Project Templates V1.1 for VS2012: This release is specifically for Visual Studio 2012 Support, distributed through the Visual Studio Extensions gallery at http://visualstudiogallery.msdn.microsoft.com/ After you build in Release mode the installable packages (source/install) can be found in the INSTALL folder now, within your module's folder, not the packages folder anymore Check out the blog post for all of the details about this release. http://www.dotnetnuke.com/Resources/Blogs/EntryId/3471/New-Visual-Studio-2012-Projec...Home Access Plus+: v8.0: v8.0828.1800 RELEASE CHANGED TO BETA Any issues, please log them on http://www.edugeek.net/forums/home-access-plus/ This is full release, NO upgrade ZIP will be provided as most files require replacing. To upgrade from a previous version, delete everything but your AppData folder, extract all but the AppData folder and run your HAP+ install Documentation is supplied in the Web Zip The Quota Services require executing a script to register the service, this can be found in there install di...Phalanger - The PHP Language Compiler for the .NET Framework: 3.0.0.3406 (September 2012): New features: Extended ReflectionClass libxml error handling, constants DateTime::modify(), DateTime::getOffset() TreatWarningsAsErrors MSBuild option OnlyPrecompiledCode configuration option; allows to use only compiled code Fixes: ArgsAware exception fix accessing .NET properties bug fix ASP.NET session handler fix for OutOfProc mode DateTime methods (WordPress posting fix) Phalanger Tools for Visual Studio: Visual Studio 2010 & 2012 New debugger engine, PHP-like debugging ...NougakuDoCompanion: v1.1.0: Add temp folder of local resource, Resize local resource. Change launch ruby commnadline args from rack to bundle. 1.NougakuDoCompanion v1.1.0 cspkg.zip - cspkg and ServiceConfiguration.xml (small , medium, large, extra large vm) - include NougakudoSetupTool.exe and readme.txt 2.NougakuDoCompanion v1.1.0.zip - Source code. include NougakudoSetupTool.exe - include activerecord-sqlserver-adapter patch in paches folder. 3.Depends tools. - Windows Azure SDK for .NET June 2012(1.7SP1) - Windows ...WatchersNET CKEditor™ Provider for DotNetNuke®: CKEditor Provider 1.14.06: Whats New Added CKEditor 3.6.4 oEmbed Plugin can now handle short urls changes The Template File can now parsed from an xml file instead of js (More Info...) Style Sets can now parsed from an xml file instead of js (More Info...) Fixed Showing wrong Pages in Child Portal in the Link Dialog Fixed Urls in dnnpages Plugin Fixed Issue #6969 WordCount Plugin Fixed Issue #6973 File-Browser: Fixed Deleting of Files File-Browser: Improved loading time File-Browser: Improved the loa...MabiCommerce: MabiCommerce 1.0.1: What's NewSetup now creates shortcuts Fix spelling errors Minor enhancement to the Map window.VFPX: Data Explorer 3: This release is the first alpha release for DX3. Even though great care has been taken, the project manager highly recommends you work with test data and you regularly back up the DataExplorer.DBF found in your HOME(7) folder. New features are documented on the project home page. IMPORTANT Once installed, make sure to go to the Data Explorer Options page, click the Restore to Default button. This brings up a dialog asking if you want to maintain connections and customizations that were done...ScintillaNET: ScintillaNET 2.5.2: This release has been built from the 2.5 branch. Version 2.5.2 is functionally identical to the 2.5.1 release but also includes the XML documentation comments file generated by Visual Studio. It is not 100% comprehensive but it will give you Visual Studio IntelliSense for a large part of the API. Just make sure the ScintillaNET.xml file is in the same folder as the ScintillaNET.dll reference you're using in your projects. (The XML file does not need to be distributed with your application)....Facebook Web Parts for SharePoint 2010: Version 1.0.1 - WSP: SharePoint 2010 solution (WSP) Resolved a bug from Version 1.0 - WSP where user profile names would not properly update.Contactor: GSMContactorProgram V1.0 - Source Code: This is the source code for the program, For Visual Studio 2012 RCTouchInjector: TouchInjector 1.1: Version 1.1: fixed a bug with the autorun optionWinRT XAML Toolkit: WinRT XAML Toolkit - 1.2.0: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features AsyncUI extensions Controls and control extensions Converters Debugging helpers Imaging IO helpers VisualTree helpers Samples Recent changes NOTE: Namespace changes DebugConsol...BlackJumboDog: Ver5.7.1: 2012.08.25 Ver5.7.1 (1)?????·?????LING?????????????? (2)SMTP???（????）????、?????\?????????????????????Visual Studio Team Foundation Server Branching and Merging Guide: v2 - Visual Studio 2012: Welcome to the Branching and Merging Guide Quality-Bar Details Documentation has been reviewed by Visual Studio ALM Rangers Documentation has been through an independent technical review Documentation has been reviewed by the quality and recording team All critical bugs have been resolved Known Issues / Bugs Spelling, grammar and content revisions are in progress. Hotfix will be published.New ProjectsAd Specific Redirect Generator: Ad Specific Redirect Generatorargsv, command line argument processors: Two libraries to process command line options, one(argsvCPython) is written for Python applications and other one(the argsvCPP) is for C++ applications.AutomationML Export Import Mapper: This Tool supports the mapping between SystemUnitClass-Libraries, used to exchange data in the AutomationML Format between Exporters and Importers.BioPathSearch: Tool for probibalistic biochemical networks construction from input substrete to required product based on information from KEGG databasebuidingapp: i am buiding app but i not sure public because i don't code finish. then i upload code and pulish my application,. thank you for reading mynote. see you next tiCatalogo de Empresas y Productos: Este es el catalogo de empresas y productos asociadas a la produccion agricola en CRclarktestcodeplex: test codeplexDatabase Clean-up Engine - DataWashroom: Database Clean-up Rules EngineEdEx: edexExpense Management System: Expense Management SystemFinger Tracking with Kinect SDK for XBOX: This project explained step by step how to perform finger and hand tracking with the Kinect for XBOX with the official Kinect SDK.Flower - Workflow Engine: Flower is a simple yet powerful workflow engine allowing to develop workflows in C#.Grid: Copyright 2011 Badkid development. All rights reserved. Play Grid the the retro style arcade puzzle game. Join lines between the gids to create boxes to get pHeadSprings Assignment: A program to create custom tokens using class FizzBuzz programming. Ice Scream: IcescreamiD Commerce + Logistics: iD Commerce + Logistics is a company based outside of Chicago, Illinois specializing in fulfillment solutions and custom development.Mido: Mido is a simple utility that adds text or images watermarks to your photos, images and pictures.MLSTest: MLSTest is a Windows based software for the analysis of Multilocus Sequence Data for euckaryotic organisms My Project Foundation Library: A foundation library for asp.net web project, including easy-to-use data access layer and other utility code.MyTestProject001: ?????codeplex，??????????。MyTestProject2: My Test projectNEF - Native Extensibility Framework: NEF is an open source IoC extensibility framework targetting C++. It is modeled after the more useful features of MEF in C#.RazorSpy: A simple toy/tool for exploring the output of the Razor Parser for a particular document.Relay Command for WinRT: A simple RelayCommand for WinRT (sans and entire MVVM framework).Rocca. Store: Document storage with email capabilitiesScrabble Nights: Scrabble is a word game in which two to four players score points by forming words from individual lettered tiles on a game board marked with a 15-by-15 gridSlFrame: SlFrameSmart Data Access layer: WE ARE USING SMART DATA ACCESS LAYER MEANS ITS TIME TO FORGET ABOUT SYSTEM.DATA.SQLCLIENT NAMESPACE.SportSlot: This project allows you to search for available sport venuesSwitcher 2012: Allows for fast switching between source and header file in Visual Studio 2012testddtfs2908201201: satime tracking: coming soonTradePlatform.NET: TradePlatform.NET is addition to MetaTrader 4 client terminal which extends trading experience, MQL language and provides .NET world communication bridge.WaMa-SkyDriveClient: Project Description WaMa-SkyDriveClient is a Windows Skydrive-client, with Live authentication.Web Optimization: The ASP.NET Web optimization framework provides services to improve the performance of your ASP.NET Web applications.Web Pocket: Web tool for rapid application development of mobile software WinRT Toolkit: The purpose of WinRT Toolkit is to provide efficient and developer friendly instruments (API / Components...).Xcel Directory Service: Xcel Directory Service is an Excel 2010 add-in used to retrieve data from Active Directory using an import utility and user defined functions.zhangfacai: this project is based on ASP.NET MVC 4 and HTML5. It's a website to integrate public web services like amazon, live, facebook, etc. By using these services, mak

  Read the article

• How do I programmatically get the current Visual State of a WPF FrameworkElement?

  - by Spines

  How do I programmatically get the current Visual State of a WPF FrameworkElement? And by state I mean the states like "Normal", "MouseOver", "Disabled", etc. EDIT: Basically, I am changing the Visual state of a button with VisualStateManager.GoToState(e, "MouseOver", true);, and I want to know what state to change it back to after I am done.

  Read the article

• "type" Command Not Working As Expected on Git Bash

  - by trysis

  The type command, in Linux, returns the location, on the filesystem, of the given file, if it is in the current folder or the $PATH. This functionality is also available through Windows with the Git Bash command line program. The command also returns a file's location given the file without its extension (.exe, .vbs, etc.) However, I have run into what seems like a strange corner case where the file exists on the $PATH but doesn't get returned using the command. I am thinking of buying a new computer soon, so I looked up the method of transferring the license key from one computer to another, in preparation for actually doing this. The method I found mentioned the files slmgr.vbs and slui.exe, both of which reside in the C:/Windows\System32 folder, which is in my $PATH, as usual for a Windows computer. However, these two files aren't showing up when I use the type command. Also, neither gets executed when I call the files as commands without their extensions in Git Bash, and only slmgr.vbs gets executed when I call them with the extensions. Finally, slmgr.vbs is shown when listing the folder's contents in Git Bash, as well, but slui.exe isn't. I thought this might have to do with permissions, and, indeed, both files have very restrictive permissions, as you can see in the pictures below, but they both have the same permissions, which wouldn't explain why one gets executed and the other doesn't when called directly, nor why one file is listed on command line but the other isn't. C:\Windows\System32 folder, proving the files exist: File permissions for the Users and Administrators groups for the two files (they are identical): And the folder: type command and its output in Git Bash for the 2 files, plus listing the files in the folder (using grep to filter as the folder is huge), as well as listing part of the $PATH (keep in mind, for all these, that Git Bash changes the paths as they are displayed): Sean@MYPC ~ $ type -a slmgr sh.exe": type: slmgr: not found Sean@MYPC ~ $ type -a slmgr.vbs sh.exe": type: slmgr.vbs: not found Sean@MYPC ~ $ type -a slui sh.exe": type: slui: not found Sean@MYPC ~ $ type -a slui.exe sh.exe": type: slui.exe: not found Sean@MYPC ~ $ slmgr sh.exe": slmgr: command not found Sean@MYPC ~ $ slmgr.vbs /c/WINDOWS/system32/slmgr.vbs: line 2: syntax error near unexpected token `(' /c/WINDOWS/system32/slmgr.vbs: line 2: `' Copyright (c) Microsoft Corporation. A ll rights reserved.' Sean@MYPC ~ $ slui sh.exe": slui: command not found Sean@MYPC ~ $ slui.exe sh.exe": slui.exe: command not found Sean@MYPC ~ $ ls /c/Windows/System32/slui.exe /c/Windows/System32/slmgr.vbs ls: /c/Windows/System32/slui.exe: No such file or directory /c/Windows/System32/slmgr.vbs Sean@MYPC ~ $ echo $PATH /c/Users/Sean/bin:.:/usr/local/bin:/mingw/bin:/bin:/cmd:/c/Python33/:/c/Program Files (x86)/Intel/iCLS Client/:/c/Program Files/Intel/iCLS Client/:/c/WINDOWS/sy stem32:/c/WINDOWS:/c/WINDOWS/System32/Wbem:/c/WINDOWS/System32/WindowsPowerShell /v1.0/:/c/Program Files/Intel/Intel(R) Management Engine Components/DAL:/c/Progr am Files/Intel/Intel(R) Management Engine Components/IPT:/c/Program Files (x86)/ Intel/Intel(R) Management Engine Components/DAL:/c/Program Files (x86)/Intel/Int el(R) Management Engine Components/IPT:/c/Program Files/Intel/WiFi/bin/:/c/Progr am Files/Common Files/Intel/WirelessCommon/:/c/strawberry/c/bin:/c/strawberry/pe rl/site/bin:/c/strawberry/perl/bin:/c/Program Files (x86)/Microsoft ASP.NET/ASP. NET Web Pages/v1.0/:/c/Program Files/Microsoft SQL Server/110/Tools/Binn/:/c/Pro gram Files (x86)/Microsoft SQL Server/90/Tools/binn/:/c/Program Files (x86)/Open AFS/Common:/c/HashiCorp/Vagrant/bin:/c/Program Files (x86)/Windows Kits/8.1/Wind ows Performance Toolkit/:/c/Program Files/nodejs/:/c/Program Files (x86)/Git/cmd :/c/Program Files (x86)/Git/bin:/c/Program Files/Microsoft/Web Platform Installe r/:/c/Ruby200-x64/bin:/c/Users/Sean/AppData/Local/Box/Box Edit/:/c/Program Files (x86)/SSH Communications Security/SSH Secure Shell:/c/Users/Sean/Documents/Lisp :/c/Program Files/GCL-2.6.1/lib/gcl-2.6.1/unixport:/c/Chocolatey/bin:/c/Users/Se an/AppData/Roaming/npm:/c/wamp/bin/mysql/mysql5.6.12/bin:/c/Program Files/Oracle /VirtualBox:/c/Program Files/Java/jdk1.7.0_51/bin:/c/Program Files/Node-Growl:/c /chocolatey/bin:/c/Program Files/eclipse:/c/MongoDB/bin:/c/Program Files/7-Zip:/ c/Program Files (x86)/Google/Chrome/Application:/c/Program Files (x86)/LibreOffi ce 4/program:/c/Program Files (x86)/OpenOffice 4/program What's happening? Why aren't these files listed with the type command? Is this issue because of weird Windows permissions, or something even weirder? If permissions, why do they seem to have the same permissions, yet both are not handled in the same way?

  Read the article

• Compile error C++: could not deduce template argument for 'T'

  - by OneShot

  I'm trying to read binary data to load structs back into memory so I can edit them and save them back to the .dat file. readVector() attempts to read the file, and return the vectors that were serialized. But i'm getting this compile error when I try and run it. What am I doing wrong with my templates? ***** EDIT ************** Code: // Project 5.cpp : main project file. #include "stdafx.h" #include <iostream> #include <fstream> #include <string> #include <vector> #include <algorithm> using namespace System; using namespace std; #pragma hdrstop int checkCommand (string line); template<typename T> void writeVector(ofstream &out, const vector<T> &vec); template<typename T> vector<T> readVector(ifstream &in); struct InventoryItem { string Item; string Description; int Quantity; int wholesaleCost; int retailCost; int dateAdded; } ; int main(void) { cout << "Welcome to the Inventory Manager extreme! [Version 1.0]" << endl; ifstream in("data.dat"); vector<InventoryItem> structList; readVector<InventoryItem>( in ); while (1) { string line = ""; cout << endl; cout << "Commands: " << endl; cout << "1: Add a new record " << endl; cout << "2: Display a record " << endl; cout << "3: Edit a current record " << endl; cout << "4: Exit the program " << endl; cout << endl; cout << "Enter a command 1-4: "; getline(cin , line); int rValue = checkCommand(line); if (rValue == 1) { cout << "You've entered a invalid command! Try Again." << endl; } else if (rValue == 2){ cout << "Error calling command!" << endl; } else if (!rValue) { break; } } system("pause"); return 0; } int checkCommand (string line) { int intReturn = atoi(line.c_str()); int status = 3; switch (intReturn) { case 1: break; case 2: break; case 3: break; case 4: status = 0; break; default: status = 1; break; } return status; } template<typename T> void writeVector(ofstream &out, const vector<T> &vec) { out << vec.size(); for(vector<T>::const_iterator i = vec.begin(); i != vec.end(); i++) { out << *i; } } ostream& operator<<(std::ostream &strm, const InventoryItem &i) { return strm << i.Item << " (" << i.Description << ")"; } template<typename T> vector<T> readVector(ifstream &in) { size_t size; in >> size; vector<T> vec; vec.reserve(size); for(int i = 0; i < size; i++) { T tmp; in >> tmp; vec.push_back(tmp); } return vec; } Compiler errors: 1>------ Build started: Project: Project 5, Configuration: Debug Win32 ------ 1>Compiling... 1>Project 5.cpp 1>.\Project 5.cpp(124) : warning C4018: '<' : signed/unsigned mismatch 1> .\Project 5.cpp(40) : see reference to function template instantiation 'std::vector<_Ty> readVector<InventoryItem>(std::ifstream &)' being compiled 1> with 1> [ 1> _Ty=InventoryItem 1> ] 1>.\Project 5.cpp(127) : error C2679: binary '>>' : no operator found which takes a right-hand operand of type 'InventoryItem' (or there is no acceptable conversion) 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(1144): could be 'std::basic_istream<_Elem,_Traits> &std::operator >><std::char_traits<char>>(std::basic_istream<_Elem,_Traits> &,signed char *)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(1146): or 'std::basic_istream<_Elem,_Traits> &std::operator >><std::char_traits<char>>(std::basic_istream<_Elem,_Traits> &,signed char &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(1148): or 'std::basic_istream<_Elem,_Traits> &std::operator >><std::char_traits<char>>(std::basic_istream<_Elem,_Traits> &,unsigned char *)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(1150): or 'std::basic_istream<_Elem,_Traits> &std::operator >><std::char_traits<char>>(std::basic_istream<_Elem,_Traits> &,unsigned char &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(155): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(std::basic_istream<_Elem,_Traits> &(__cdecl *)(std::basic_istream<_Elem,_Traits> &))' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(161): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(std::basic_ios<_Elem,_Traits> &(__cdecl *)(std::basic_ios<_Elem,_Traits> &))' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(168): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(std::ios_base &(__cdecl *)(std::ios_base &))' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(175): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(std::_Bool &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(194): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(short &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(228): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(unsigned short &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(247): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(int &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(273): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(unsigned int &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(291): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(long &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(309): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(__w64 unsigned long &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(329): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(__int64 &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(348): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(unsigned __int64 &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(367): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(float &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(386): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(double &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(404): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(long double &)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(422): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(void *&)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\include\istream(441): or 'std::basic_istream<_Elem,_Traits> &std::basic_istream<_Elem,_Traits>::operator >>(std::basic_streambuf<_Elem,_Traits> *)' 1> with 1> [ 1> _Elem=char, 1> _Traits=std::char_traits<char> 1> ] 1> while trying to match the argument list '(std::ifstream, InventoryItem)' 1>Build log was saved at "file://c:\Users\Owner\Documents\Visual Studio 2008\Projects\Project 5\Project 5\Debug\BuildLog.htm" 1>Project 5 - 1 error(s), 1 warning(s) ========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ========== Oh my god...I fixed that error I think and now I got another one. Will you PLEASE just help me on this one too! What the heck does this mean ??

  Read the article

• How to use visual leak detecter ( vld ) for com/atl dll projects?

  - by Rajesh Subramanian

  I included vld.h file in my activex dll project. when i try to compile my project from visual studio 2008.I am getting the following error, 1Registering output... 1Project : error PRJ0050: Failed to register output. Please ensure you have the appropriate permissions to modify the registry. How to use visual leak detecter for com/activex dll projects?

  Read the article

• How do you force Visual Studio 2008 to generate designer.cs e.g. Whatever.aspx.designer.cs

  - by tinyJoe

  I have some webforms in an Asp.Net V2.0 generated using Visual Studio 2005 using Web site technology Want to import them in to Visual Studio 2008 set to v3.5 (Asp.Net MVC) - where I use Project technology I'm using Add Existing Item - Which brings in Whatever.aspx & Whatever.aspx.cs There is no Whatever.aspx.designer.cs to import How do you force it to be generated ?

  Read the article

• Code coverage test in Visual Studio 2010? How?

  - by George

  Hello, I have a simple project on C#.NET and have written it in Visual Studio 2010. I am a newbie in C# and Visual Studio. I have written some unit tests, and they pass ok, but how can I test code coverage? Thanks in advance.

  Read the article

• How can I install a windows service onto a machine that doesn't have Visual Studio installed?

  - by infant programmer

  The only way to install windows-service I know is using "Visual Studio 2008 Command Prompt", Is there a way to install windows-service on a machine which isn't having Visual Studio installed (assume that .Net version 2.X is installed.)

  Read the article

• What if an application needs MSVCR80.dll but I've installed Microsoft Visual Studio 9.0?

  - by user198729

  I'm trying to install this: http://www.coderholic.com/pywebshot-generate-website-thumbnails-using-python/ I've googled a lot,and still can't make it work(gtk runtime has been installed successfully(gtk-demo works),but it still reports can't find MSVCR80.dll,this should be because that I have installed Microsoft Visual Studio 9.0?), each time it reports ImportError: DLL load failed,MSVCR80.dll is not found.. How to make an application that needs MSVCR80.dll work when I've already installed Microsoft Visual Studio 9.0? Or : How to make _gtk.pyd use MSVCR90.dll instead of MSVCR80.dll?

  Read the article

• using Visual Studio 2010 and speech recognition on windows 7?

  - by Kevin Won

  I've never used Speech Recognition (SR) at all, but I'm hearing that the built-in SR capabilities of windows 7 is not half-bad. I'm thinking that it might be a real productivity booster with Visual Studio so I can decrease the use of the mouse (no Emacs comments please ;-). I don't envision not using the keyboard to type the actual code--but maybe that would work too? Does anyone have experience using SR with Visual Studio on Windows 7? If so, any tips on usage?

  Read the article

• Are there any dangers in using Visual Studio 2010 to develop .net 3.5 sp1 products?

  - by urig

  We're excited at the prospect of upgrading our development IDE from Visual Studio 2008 to 2010. Our production environment, however, is not scheduled to be upgraded from .net 3.5 sp1 to .net 4.0 in the near future. What are the possible risks in using Visual Studio 2010 to develop production grade applications that will actually run on .net 3.5 sp1 ?

  Read the article

• How to install a windows-service which doesn't have visual-studio installed?

  - by infant programmer

  The only way to install windows-service I know is using "Visual Studio 2008 Command Prompt", Is there a way to install windows-service on a machine which isn't having Visual Studio installed (assume that .Net version 2.X is installed.)

  Read the article

• Acer aspire 5735z wireless not working after upgrade to 11.10

  - by Jon

  I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

  Read the article

• CodePlex Daily Summary for Thursday, November 01, 2012

  CodePlex Daily Summary for Thursday, November 01, 2012Popular ReleasesAccess 2010 Application Platform - Build Your Own Database: Application Platform - 0.0.1: Initial Release This is the first version of the database. At the moment is all contained in one file to make development easier, but the obvious idea would be to split it into Front and Back End for a production version of the tool. The features it contains at the moment are the "Core" features.Python Tools for Visual Studio: Python Tools for Visual Studio 1.5: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, etc. support. For a quick overview of the general IDE experience, please watch this video There are a number of exciting improvement in this release comp...Devpad: 4.25: Whats new for Devpad 4.25: New Theme support New Export Wordpress Minor Bug Fix's, improvements and speed upsAssaultCube Reloaded: 2.5.5: Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we try to package for those OSes. Try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compile your own for Linux (source included) Changelog: Fixed potential bot bugs: Map change, OpenAL...Edi: Edi 1.0 with DarkExpression: Added DarkExpression theme (dialogs and message boxes are not completely themed, yet)MCEBuddy 2.x: MCEBuddy 2.3.6: Changelog for 2.3.6 (32bit and 64bit) 1. Fixed a bug in multichannel audio conversion failure. AAC does not support 6 channel audio, MCEBuddy now checks for it and force the output to 2 channel if AAC codec is specified 2. Fixed a bug in Original Broadcast Date and Time. Original Broadcast Date and Time is reported in UTC timezone in WTV metadata. TVDB and MovieDB dates are reported in network timezone. It is assumed the video is recorded and converted on the same machine, i.e. local timezone...MVVM Light Toolkit: MVVM Light Toolkit V4.1 for Visual Studio 2012: This version only supports Visual Studio 2012 (and all Express editions too). If you use Visual Studio 2010, please stay tuned, we will publish an update in a few days with support for VS10. V4.1 supports: Windows Phone 8 Windows 8 (Windows RT) Silverlight 5 Silverlight 4 WPF 4.5 WPF 4 WPF 3.5 And the following development environments: Visual Studio 2012 (Pro, Premium, Ultimate) Visual Studio 2012 Express for Windows 8 Visual Studio 2012 Express for Windows Phone 8 Visual...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.73: Fix issue in Discussion #401101 (unreferenced var in a for-in statement was getting removed). add the grouping operator to the parsed output so that unminified parsed code is closer to the original. Will still strip unneeded parens later, if minifying. more cleaning of references as they are minified out of the code.Liberty: v3.4.0.1 Release 28th October 2012: Change Log -Fixed -H4 Fixed the save verification screen showing incorrect mission and difficulty information for some saves -H4 Hopefully fixed the issue where progress did not save between missions and saves would not revert correctly -H3 Fixed crashes that occurred when trying to load player information -Proper exception dialogs will now show in place of crashesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536Orchard Project: Orchard 1.6: Please read our release notes for Orchard 1.6: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you will pollute the rating, and you won't get an answer.Media Companion: Media Companion 3.507b: Once again, it has been some time since our release, and there have been a number changes since then. It is hoped that these changes will address some of the issues users have been experiencing, and of course, work continues! New Features: Added support for adding Home Movies. Option to sort Movies by votes. Added 'selectedBrowser' preference used when opening links in an external browser. Added option to fallback to getting runtime from the movie file if not available on IMDB. Added new Big...MSBuild Extension Pack: October 2012: Release Blog Post The MSBuild Extension Pack October 2012 release provides a collection of over 475 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...NAudio: NAudio 1.6: Release notes at http://mark-dot-net.blogspot.co.uk/2012/10/naudio-16-release-notes-10th.htmlPowerShell Community Extensions: 2.1 Production: PowerShell Community Extensions 2.1 Release NotesOct 25, 2012 This version of PSCX supports both Windows PowerShell 2.0 and 3.0. See the ReleaseNotes.txt download above for more information.Umbraco CMS: Umbraco 4.9.1: Umbraco 4.9.1 is a bugfix release to fix major issues in 4.9.0 BugfixesThe full list of fixes can be found in the issue tracker's filtered results. A summary: Split buttons work again, you can now also scroll easier when the list is too long for the screen Media and Content pickers have information of the full path of the picked item Fixed: Publish status may not be accurate on nodes with large doctypes Fixed: 2 media folders and recycle bins after upgrade to 4.9 The template/code ...AcDown????? - AcDown Downloader Framework: AcDown????? v4.2.2: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown??????????????????，????????????????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???，????????.NET Framework 2.0???(x86)，?????"?????????"??? (2)???????????Linux???，????????Mono?? ??2...Rawr: Rawr 5.0.2: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...New ProjectsAsbesto: Proyecto grupo: "2ravas" para Laboratorio de Computación IV de la carrera TSP de la UTN-FRGP Realizado en C# y ASP.NET en Visual Studio 2012 y SQL Server 2012C++ Diamond printer on console without if statement: prints just a diamond with stars(*). only one important and funny feature is that it's not using 'if' statement. C++ used.CloudTest: Test cloud computing projectEnumeration of objects Class Library C#: At core level in Java I like extension of traditional enum type permiting use as the elements instances of a class. The project implements the same idea by C# with some more advanced features like a set type with boolean operators extending idea of FlagsAttributeEquation Inversion: Visual Studion 2008 Add-in for equation inversions.ESENT Serialization Class Library: ESENT Serialization class library is built above Managed ESENT. It allows you to store your objects in the underlying extensible storage engine database.ForceHttps: Very simple httpModule to ensure that all http requests are https. 1. Drop the dll into your website's bin directory 2. Update httpModules section of your web.config to reference the dll 3. Make sure your Web Server can handle SSL requests for the URL ALL http requests will be redirected as https.forrajeriaPAV2: tp pav2 asd as asd as fasfjaijiasjifoa as asf asf as afs fas asf afs fsaGoogle Analytics for WinRT: A Windows Store (WinRT) class library for tracking Google Analytics page views, events, and custom variables for your Metro style desktop and tablet apps.huanglitest10312: mvc projectiMan: iMan will be your own port manager, which help to provide the information about all the ports open in your PC It's completely developed in .NET C#InjectionCop: Facilitates secure coding through static code analysis and contract annotations in the Common Language Infrastructure.Master of Olympus: Remake of Master of Olympus : Zeus, a game developed by Impressions Games in 2000.MediaScribe: MediaScribe is a note app for your media.MouseNestDotNet: A small personal website application.Project Estimator ???????? ?? ?????????????? ?? ???????: Project Estimator ? ???????? ??????????? ? ??????????? ?? ????? ? ???????? ????.Projekt grupowy 1: Project created only for school purpose.SecondHandApp: Warenwirtschaftsprogramm für denn SecondHand LädenSimple .NET XML Serialization: .NET's XML serialization using Linq XObject classes EG: XElement in an IXmlSerializable base classStrip Converter: A Very Handy Converter for 2D Games Developers Developer Website: http://www.bluebulk.infoSwitch JS Control (Client Side): Switch JS control is a very light client side library to create switch(es) on web applications or mobile applications.VisaSys: Visa System????????: TODO::????

  Read the article

• How do I stop XNA/Visual Studio from rebuilding my content project every time I build?

  - by Phil Quinn

  My group and I are working on a game in XNA 4.0 with Visual Studio 2010/2012. The main solution has 6 projects: 2 XNA game projects (1 executable/ 1 class library), 1 WPF executable for the level editor, 2 standard class libraries, and a content project. Originally, the editor and engine XNA game projects had a content reference to separate content projects. Recently, I consolidated the content projects into one to simplify asset additions. Since pushing these changes to our git repo, certain members of my group have been experiencing weird build issues. Every time they run the project, they have to re-build all of the assets. This happens regardless of whether any changes were made, even if they just run the project directly after building. I've taken a few steps to figure out why this is happening. Below is the MSBuild output set on Normal verbosity. The seemingly important part is at 4, with the line 4> Rebuilding all content because build settings have changed 1>------ Build started: Project: Engine.Core, Configuration: Debug x86 ------ 1>Build started 11/29/2012 3:24:24 AM. 1>ResolveAssemblyReferences: 1> A TargetFramework profile exclusion list will be generated. 1>EmbedXnaFrameworkRuntimeProfile: 1>Skipping target "EmbedXnaFrameworkRuntimeProfile" because all output files are up-to-date with respect to the input files. 1>GenerateTargetFrameworkMonikerAttribute: 1>Skipping target "GenerateTargetFrameworkMonikerAttribute" because all output files are up-to-date with respect to the input files. 1>CoreCompile: 1>Skipping target "CoreCompile" because all output files are up-to-date with respect to the input files. 1>XnaWriteCacheFile: 1>Skipping target "XnaWriteCacheFile" because all output files are up-to-date with respect to the input files. 1>_CopyOutOfDateSourceItemsToOutputDirectoryAlways: 1> Copying file from "<solution-dir>\src\Engine.Core\DialoguePrototypeTestDB.s3db" to "bin\x86\Debug\DialoguePrototypeTestDB.s3db". 1>_CopyAppConfigFile: 1>Skipping target "_CopyAppConfigFile" because all output files are up-to-date with respect to the input files. 1>CopyFilesToOutputDirectory: 1> Engine.Core -> <solution-dir>\src\Engine.Core\bin\x86\Debug\TimeSink.Engine.Core.dll 1> 1>Build succeeded. 1> 1>Time Elapsed 00:00:00.13 2>------ Build started: Project: TimeSink.Entities, Configuration: Debug x86 ------ 2>Build started 11/29/2012 3:24:25 AM. 2>ResolveAssemblyReferences: 2> A TargetFramework profile exclusion list will be generated. 2>EmbedXnaFrameworkRuntimeProfile: 2>Skipping target "EmbedXnaFrameworkRuntimeProfile" because all output files are up-to-date with respect to the input files. 2>GenerateTargetFrameworkMonikerAttribute: 2>Skipping target "GenerateTargetFrameworkMonikerAttribute" because all output files are up-to-date with respect to the input files. 2>CoreCompile: 2>Skipping target "CoreCompile" because all output files are up-to-date with respect to the input files. 2>XnaWriteCacheFile: 2>Skipping target "XnaWriteCacheFile" because all output files are up-to-date with respect to the input files. 2>_CopyOutOfDateSourceItemsToOutputDirectoryAlways: 2> Copying file from "<solution-dir>\src\Engine.Core\DialoguePrototypeTestDB.s3db" to "bin\x86\Debug\DialoguePrototypeTestDB.s3db". 2>CopyFilesToOutputDirectory: 2> TimeSink.Entities -> <solution-dir>\src\TimeSink.Entities\bin\x86\Debug\TimeSink.Entities.dll 2> 2>Build succeeded. 2> 2>Time Elapsed 00:00:00.11 3>------ Build started: Project: Editor (Editor\Editor), Configuration: Debug x86 ------ 4>------ Build started: Project: Engine.Game, Configuration: Debug x86 ------ 3>Build started 11/29/2012 3:24:25 AM. 3>CoreCompile: 3> All content is already up to date 3>ResolveAssemblyReferences: 3> A TargetFramework profile exclusion list will be generated. 3>EmbedXnaFrameworkRuntimeProfile: 3>Skipping target "EmbedXnaFrameworkRuntimeProfile" because all output files are up-to-date with respect to the input files. 3>GenerateTargetFrameworkMonikerAttribute: 3>Skipping target "GenerateTargetFrameworkMonikerAttribute" because all output files are up-to-date with respect to the input files. 3>CoreCompile: 3>Skipping target "CoreCompile" because all output files are up-to-date with respect to the input files. 3>XnaWriteCacheFile: 3>Skipping target "XnaWriteCacheFile" because all output files are up-to-date with respect to the input files. 3>_CopyOutOfDateSourceItemsToOutputDirectoryAlways: 3> Copying file from "<solution-dir>\src\Engine.Core\DialoguePrototypeTestDB.s3db" to "bin\x86\Debug\DialoguePrototypeTestDB.s3db". 3>_CopyOutOfDateNestedContentItemsToOutputDirectory: 3>Skipping target "_CopyOutOfDateNestedContentItemsToOutputDirectory" because all output files are up-to-date with respect to the input files. 3>CopyFilesToOutputDirectory: 3> Editor -> <solution-dir>\src\Editor\Editor\bin\x86\Debug\Editor.dll 3> 3>Build succeeded. 3> 3>Time Elapsed 00:00:00.39 4>Build started 11/29/2012 3:24:25 AM. 4>CoreCompile: 4> Rebuilding all content because build settings have changed 4> Building Textures\circle.png -> <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\circle.xnb 4> Importing Textures\circle.png with Microsoft.Xna.Framework.Content.Pipeline.TextureImporter 4> Processing Textures\circle.png with Microsoft.Xna.Framework.Content.Pipeline.Processors.TextureProcessor 4> Compiling <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\circle.xnb 4> Building Textures\giroux.png -> <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\giroux.xnb 4> Importing Textures\giroux.png with Microsoft.Xna.Framework.Content.Pipeline.TextureImporter 4> Processing Textures\giroux.png with Microsoft.Xna.Framework.Content.Pipeline.Processors.TextureProcessor 4> Compiling <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\giroux.xnb 4> Building Textures\Body_Neutral.png -> <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\Body_Neutral.xnb 4> Importing Textures\Body_Neutral.png with Microsoft.Xna.Framework.Content.Pipeline.TextureImporter 4> Processing Textures\Body_Neutral.png with Microsoft.Xna.Framework.Content.Pipeline.Processors.TextureProcessor 4> Compiling <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\Textures\Body_Neutral.xnb 4> Building font.spritefont -> <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\font.xnb 4> Importing font.spritefont with Microsoft.Xna.Framework.Content.Pipeline.FontDescriptionImporter 4> Processing font.spritefont with Microsoft.Xna.Framework.Content.Pipeline.Processors.FontDescriptionProcessor 4> Compiling <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Content\font.xnb 4>ResolveAssemblyReferences: 4> A TargetFramework profile exclusion list will be generated. 4>EmbedXnaFrameworkRuntimeProfile: 4>Skipping target "EmbedXnaFrameworkRuntimeProfile" because all output files are up-to-date with respect to the input files. 4>GenerateTargetFrameworkMonikerAttribute: 4>Skipping target "GenerateTargetFrameworkMonikerAttribute" because all output files are up-to-date with respect to the input files. 4>CoreCompile: 4>Skipping target "CoreCompile" because all output files are up-to-date with respect to the input files. 4>_CopyOutOfDateSourceItemsToOutputDirectoryAlways: 4> Copying file from "<solution-dir>\src\Engine.Core\DialoguePrototypeTestDB.s3db" to "bin\x86\Debug\DialoguePrototypeTestDB.s3db". 4>_CopyOutOfDateNestedContentItemsToOutputDirectory: 4>Skipping target "_CopyOutOfDateNestedContentItemsToOutputDirectory" because all output files are up-to-date with respect to the input files. 4>_CopyAppConfigFile: 4>Skipping target "_CopyAppConfigFile" because all output files are up-to-date with respect to the input files. 4>CopyFilesToOutputDirectory: 4> Engine.Game -> <solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Engine.Game.exe 4>IncrementalClean: 4> Deleting file "<solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\circle.xnb". 4> Deleting file "<solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\giroux.xnb". 4> Deleting file "<solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\Body_Neutral.xnb". 4> Deleting file "<solution-dir>\src\Engine.Game\Engine.Game\bin\x86\Debug\font.xnb". 4> 4>Build succeeded. 4> 4>Time Elapsed 00:00:01.72 ========== Build: 4 succeeded, 0 failed, 1 up-to-date, 0 skipped ========== I can't think of how build settings could change between consecutive executions. Like I said, this only happens for half our group. One member is on a 32-bit Windows 7 Prof bootcamp partition on a Mac. Everyone else, including those who don't have the issue, are running straight 64-bit Windows 7 Prof. Both have tried using VS 2010 and VS 2012. Any insight would be greatly appreciated. Also, I can post more details upon request if this isn't thorough enough.

  Read the article

• Semana Tecnológica New Horizons

  - by carlone

    La semana pasada tuve la oportunidad de participar en la Semana Tecnológica organizada por New Horizons Guatemala   En esta oportunidad brinde dos charlas:   Visual Studio 2012 New Features   Programando MVC 4 con Visual Studio 2012   Les comparto algunos videos publicados en mi canal de YouTube con demostraciones de los temas presentados:   Visual Studio 2012 Serie Web: Page Inspector   Visual Studio 2012 Serie Web: Web Designer   Visual Studio 2012 Serie Web: Caracteristicas de Edicion HTML   Saludos Cordiales,   Carlos A. Lone

  Read the article

• New Office 2010 theme added for creating current UIs

  - by Webgui

  Visual WebGui offers its developers a set of out-of-the-box themes which they can easily apply to their applications. This allows developers to focus on the development and business logic rather than dealing with UI design missions. However, design tools and customization freedom are available for those who need to customize current themes or create their own custom theme. As part of the constant updates and enhancements to Visual WebGui and its developer CompanionKit a new available theme was added last week. The new theme applies the latest Microsoft UI - Office 2010 to Visual WebGui and allows developers and/or end users (of 6.4.0 and above) to switch their Web applications UI to the successful design of Office 2010. After the latest update the new theme is integrated into the Visual WebGui Developers CompanionKit which now matches Visual WebGui 6.4.0 Release version's infrastructure. The update also includes several enhancements to existing controls and features and the addition of some new ones. Go to the CompanionKit

  Read the article

• Coreinfo reports i7-3770 CPU doesn't support EPT (aka SLAT) and VMX

  - by Toro

  Here is the output: Coreinfo v3.05 - Dump information on system CPU and memory topology Copyright (C) 2008-2012 Mark Russinovich Sysinternals - www.sysinternals.com Note: Coreinfo must be executed on a system without a hypervisor running for accurate results. Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz Intel64 Family 6 Model 58 Stepping 9, GenuineIntel HYPERVISOR * Hypervisor is present VMX - Supports Intel hardware-assisted virtualization EPT - Supports Intel extended page tables (SLAT) According to Intel the CPU does have a VMX and EPT support.

  Read the article

• Why did this work with Visual C++, but not with gcc?

  - by Carlos Nunez

  I've been working on a senior project for the last several months now, and a major sticking point in our team's development process has been dealing wtih rifts between Visual-C++ and gcc. (Yes, I know we all should have had the same development environment.) Things are about finished up at this point, but I ran into a moderate bug just today that had me wondering whether Visual-C++ is easier on newbies (like me) by design. In one of my headers, there is a function that relies on strtok to chop up a string, do some comparisons and return a string with a similar format. It works a little something like the following: int main() { string a, b, c; //Do stuff with a and b. c = get_string(a,b); } string get_string(string a, string b) { const char * a_ch, b_ch; a_ch = strtok(a.c_str(),","); b_ch = strtok(b.c_str(),","); } strtok is infamous for being great at tokenizing, but equally great at destroying the original string to be tokenized. Thus, when I compiled this with gcc and tried to do anything with a or b, I got unexpected behavior, since the separator used was completely removed in the string. Here's an example in case I'm unclear; if I set a = "Jim,Bob,Mary" and b="Grace,Soo,Hyun", they would be defined as a="JimBobMary" and b="GraceSooHyun" instead of staying the same like I wanted. However, when I compiled this under Visual C++, I got back the original strings and the program executed fine. I tried dynamically allocating memory to the strings and copying them the "standard" way, but the only way that worked was using malloc() and free(), which I hear is discouraged in C++. While I'm curious about that, the real question I have is this: Why did the program work when compiled in VC++, but not with gcc? (This is one of many conflicts that I experienced while trying to make the code cross-platform.) Thanks in advance! -Carlos Nunez

  Read the article

• Troubling starting new silverlight 4.0 project (in f#) from VS2010

  - by akaphenom

  I am trying to protoype a silverlight 4.0 project using F#, and am having issues getting it to install... the silverlight 4 tools for Visual Studio 2010 is barking at me: Installation Requirements: Visual Studio 2010 or Visual Web Developer Express 2010 or Visual Phone Developer Express 2010 that matches the language version of Silverlight Tools 4 must be installed before installation of Silverlight Tools can continue. Silverlight Tools is available in other languages at http://go.microsoft.com/fwlink/?LinkId=177432. VS INfo Microsoft Visual Studio 2010 Version 10.0.30128.1 RC1Rel Microsoft .NET Framework Version 4.0.30128 RC1Rel Installed Version: Professional Microsoft Visual F# 2010 01018-315-4422943-70575 Microsoft Visual F# 2010 Thank you in advance

  Read the article

• Now Available &ndash; Windows Azure SDK 1.6

  - by Shaun

  Microsoft has just announced the Windows Azure SDK 1.6 and the Windows Azure Tools for Visual Studio 1.6. Now people can download the latest product through the WebPI. After you downloaded and installed the SDK you will find that The SDK 1.6 can be stayed side by side with the SDK 1.5, which means you can still using the 1.5 assemblies. But the Visual Studio Tools would be upgraded to 1.6. Different from the previous SDK, in this version it includes 4 components: Windows Azure Authoring Tools, Windows Azure Emulators, Windows Azure Libraries for .NET 1.6 and the Windows Azure Tools for Microsoft Visual Studio 2010. There are some significant upgrades in this version, which are Publishing Enhancement: More easily connect to the Windows Azure when publish your application by retrieving a publish setting file. It will let you configure some settings of the deployment, without getting back to the developer portal. Multi-profiles: The publish settings, cloud configuration files, etc. will be stored in one or more MSBuild files. It will be much easier to switch the settings between vary build environments. MSBuild Command-line Build Support. In-Place Upgrade Support.   Publishing Enhancement So let’s have a look about the new features of the publishing. Just create a new Windows Azure project in Visual Studio 2010 with a MVC 3 Web Role, and right-click the Windows Azure project node in the solution explorer, then select Publish, we will find the new publish dialog. In this version the first thing we need to do is to connect to our Windows Azure subscription. Click the “Sign in to download credentials” link, we will be navigated to the login page to provide the Live ID. The Windows Azure Tool will generate a certificate file and uploaded to the subscriptions those belong to us. Then we will download a PUBLISHSETTINGS file, which contains the credentials and subscriptions information. The Visual Studio Tool will generate a certificate and deployed to the subscriptions you have as the Management Certificate. The VS Tool will use this certificate to connect to the subscription in the next step. In the next step, I would back to the Visual Studio (the publish dialog should be stilling opened) and click the Import button, select the PUBLISHSETTINGS file I had just downloaded. Then all my subscriptions will be shown in the dropdown list. Select a subscription that I want the application to be published and press the Next button, then we can select the hosted service, environment, build configuration and service configuration shown in the dialog. In this version we can create a new hosted service directly here rather than go back to the developer portal. Just select the <Create New …> item in the hosted service. What we need to do is to provide the hosted service name and the location. Once clicked the OK, after several seconds the hosted service will be established. If we went to the developer portal we will find the new hosted service in my subscription. a) Currently we cannot select the Affinity Group when create a new hosted service through the Visual Studio Publish dialog. b) Although we can specify the hosted service name and DNS prefixing through the developer portal, we cannot do so from the VS Tool, which means the DNS prefixing would be the same as what we specified for the hosted service name. For example, we specified our hosted service name as “Sdk16Demo”, so the public URL would be http://sdk16demo.cloudapp.net/. After created a new hosted service we can select the cloud environment (production or staging), the build configuration (release or debug), and the service configuration (cloud or local). And we can set the Remote Desktop by check the related checkbox as well. One thing should be note is that, in this version when we set the Remote Desktop settings we don’t need to specify a certificate by default. This is because the Visual Studio will generate a new certificate for us by default. But we can still specify an existing certificate for RDC, by clicking the “More Options” button. Visual Studio Tool will create another certificate for the Remote Desktop connection. It will NOT use the certificate that managing the subscription. We also can select the “Advanced Settings” page to specify the deployment label, storage account, IntelliTrace and .NET profiling information, etc.. Press Next button, the dialog will display all settings I had just specified and it will save them as a new profile. The last step is to click the Publish button. Since we enabled the Remote Desktop feature, the first step of publishing was uploading the certificate. And then it will verify the storage account we specified and upload the package, then finally created the website in Windows Azure.   Multi-Profiles After published, if we back to the Visual Studio we can find a AZUREPUBXML file under the Profiles folder in the Azure project. It includes all settings we specified before. If we publish this project again, we can just use the current settings (hosted service, environment, RDC, etc.) from this profile without input them again. And this is very useful when we have more than one deployment settings. For example it would be able to have one AZUREPUBXML profile for deploying to testing environment (debug building, less roles with RDC and IntelliTrace) and one for production (release building, more roles but without IntelliTrace).   In-Place Upgrade Support Let’s change some codes in the MVC pages and click the Publish menu from the azure project node. No need to specify any settings,  here we can use the pervious settings by loading the azure profile file (AZUREPUBXML). After clicked the Publish button the VS Tool brought a dialog to us to indicate that there’s a deployment available in the hosted service environment, and prompt to REPLACE it or not. Notice that in this version, the dialog tool said “replace” rather than “delete”, which means by default the VS Tool will use In-Place Upgrade when we deploy to a hosted service that has a deployment already exist. After click Yes the VS Tool will upload the package and perform the In-Place Upgrade. If we back to the developer portal we can find that the status of the hosted service was turned to “Updating…”. But in the previous SDK, it will try to delete the whole deployment and publish a new one.   Summary When the Microsoft announced the features that allows the changing VM size via In-Place Upgrade, they also mentioned that in the next few versions the user experience of publishing the azure application would be improved. The target was trying to accomplish the whole publish experience in Visual Studio, which means no need to touch developer portal any more. In the SDK 1.6 we can see from the new publish dialog, as a developer we can do the whole process, includes creating hosted service, specifying the environment, configuration, remote desktop, etc. values without going back the the developer portal.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >