Search Results

Search found 16491 results on 660 pages for 'root node'.

Page 347/660 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• nginx reverse proxy cannot access apache virtual hosts

  - by Sc0rian

  I am setting up nginx as a reverse proxy. The server runs on directadmin and lamp stack. I have nginx running on port 81. I can access all my sites (including virtual ips) on the port 81. However when I forward the traffic from port 80 to 81, the virtual ips have a message saying "Apache is running normally". Server IPs are fine, and I can still access virtual IP's on 81. [root@~]# netstat -an | grep LISTEN | egrep ":80|:81" tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <serverip>:81 0.0.0.0:* LISTEN tcp 0 0 :::80 :::* LISTEN apache 24090 0.6 1.3 29252 13612 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24092 0.9 2.1 39584 22056 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24096 0.2 1.9 35892 20256 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24120 0.3 1.7 35752 17840 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24495 0.0 1.4 30892 14756 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24496 1.0 2.1 39892 22164 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24516 1.5 3.6 55496 38040 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24519 0.1 1.2 28996 13224 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24521 2.7 4.0 58244 41984 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24522 0.0 1.2 29124 12672 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24524 0.0 1.1 28740 12364 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24535 1.1 1.7 36008 17876 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24536 0.0 1.1 28592 12084 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24537 0.0 1.1 28592 12112 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24539 0.0 0.0 0 0 ? Z 18:35 0:00 [httpd] <defunct> apache 24540 0.0 1.1 28592 11540 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24541 0.0 1.1 28592 11548 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL root 24548 0.0 0.0 4132 752 pts/0 R+ 18:35 0:00 egrep apache|nginx root 28238 0.0 0.0 19576 284 ? Ss May29 0:00 nginx: master process /usr/local/nginx/sbin/nginx -c /usr/local/nginx/conf/nginx.conf apache 28239 0.0 0.0 19888 804 ? S May29 0:00 nginx: worker process apache 28240 0.0 0.0 19888 548 ? S May29 0:00 nginx: worker process apache 28241 0.0 0.0 19736 484 ? S May29 0:00 nginx: cache manager process here is my nginx conf: cat /usr/local/nginx/conf/nginx.conf user apache apache; worker_processes 2; # Set it according to what your CPU have. 4 Cores = 4 worker_rlimit_nofile 8192; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] ' '"$request" $status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; server_tokens off; access_log /var/log/nginx_access.log main; error_log /var/log/nginx_error.log debug; server_names_hash_bucket_size 64; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 30; gzip on; gzip_comp_level 9; gzip_proxied any; proxy_buffering on; proxy_cache_path /usr/local/nginx/proxy_temp levels=1:2 keys_zone=one:15m inactive=7d max_size=1000m; proxy_buffer_size 16k; proxy_buffers 100 8k; proxy_connect_timeout 60; proxy_send_timeout 60; proxy_read_timeout 60; server { listen <server ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <server host name> _; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<server ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } location /nginx_status { stub_status on; access_log off; allow 127.0.0.1; deny all; } } include /usr/local/nginx/vhosts/*.conf; } here is my vhost conf: # cat /usr/local/nginx/vhosts/1.conf server { listen <virt ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <virt domain name>.com ; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<virt ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } } Apache config: <VirtualHost xxxxxx:80 > ServerName www.<domain>.com ServerAlias www.<domain>.com <domain>.com ServerAdmin webmaster@<domain>.com DocumentRoot /home/<domain>/domains/<domain>.com/public_html ScriptAlias /cgi-bin/ /home/<domain>/domains/<domain>.com/public_html/cgi-bin/ UseCanonicalName OFF <IfModule !mod_ruid2.c> SuexecUserGroup <domain> <domain> </IfModule> <IfModule mod_ruid2.c> RMode config RUidGid <domain> <domain> RGroups apache access </IfModule> CustomLog /var/log/httpd/domains/<domain>.com.bytes bytes CustomLog /var/log/httpd/domains/<domain>.com.log combined ErrorLog /var/log/httpd/domains/<domain>.com.error.log <Directory /home/<domain>/domains/<domain>.com/public_html> Options +Includes -Indexes php_admin_flag engine ON php_admin_value sendmail_path '/usr/sbin/sendmail -t -i -f <domain>@<domain>.com' </Directory> <virtual ip address>:80 is a NameVirtualHost default server www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:16) port 80 namevhost www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:16) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:107) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:151) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/xx/httpd.conf:195) <virtual ip address>:443 is a NameVirtualHost default server www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:61) port 443 namevhost www.xx.com (/usr/local/directadmin/data/users/xx/httpd.conf:61) <server ip>:80 is a NameVirtualHost default server localhost (/etc/httpd/conf/extra/httpd-vhosts.conf:29) port 80 namevhost localhost (/etc/httpd/conf/extra/httpd-vhosts.conf:29) port 80 namevhost www.xx.co.uk (/usr/local/directadmin/data/users/admin/httpd.conf:16)

  Read the article

• LVM snapshot size

  - by Devator

  I currently have 2 volume's: [root@compute4 /]# lvscan ACTIVE '/dev/vps/vm108_img' [30.00 GB] inherit ACTIVE '/dev/vps/vm109_img' [90.00 GB] inherit Now, I use the LVM snapshot function to create backups. My quesion is, what size does the snapshot needs to be? Atleast the same as the volume in question or can it be a lot smaller and will only the changes be saved into it?

  Read the article

• How to install MySQL on Windows 7

  - by akash gupta

  Please help me how to install MySQL on Windows 7. When I tried to install, I am getting errors as: The security settings could not be applied to the database because the connection has failed of the following errors ERROR NR:1045 Access denied for user 'root@'localhost(using password yes). I tried to uninstall MySQL completely and install again, but it shows this error again and again. I have changed my firewall setting also and tried unstalling antivirus sotware too. But it also did not work.

  Read the article

• sudo apt-get install apache2 does not fetch apache

  - by dave

  Hello, Trying out sudo apt-get install apache2 This is what I get root@x27:/home/test# sudo apt-get install apache2 Reading package lists... Done Building dependency tree Reading state information... Done E: Couldn't find package apache2 Appreciate help for using apt-get for apache Thanks Dave

  Read the article

• Passenger 2.2.4, nginx 0.7.61 and SSL

  - by boompa

  Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

  Read the article

• sudo apt-get install apache2 does not fetch apache

  - by dave

  Hello, Trying out sudo apt-get install apache2 This is what I get root@x27:/home/test# sudo apt-get install apache2 Reading package lists... Done Building dependency tree Reading state information... Done E: Couldn't find package apache2 Appreciate help for using apt-get for apache Thanks Dave

  Read the article

• Can I specify PBKDF2 rounds to use with LUKS/dm-crypt?

  - by Naftuli Tzvi Kay

  I have encrypted my root partition with dm-crypt/LUKS/cryptsetup on Ubuntu 12.04. Since it uses PBKDF2: Is it possible, during creation of the encrypted disk, to specify a custom amount of PBKDF2 iterations for key derivation? Is it possible, after the encrypted disk has already been created, to modify the amount of PBKDF2 iterations for key derivation? I'd like to make it a little harder to brute-force :)

  Read the article

• How to set up linux watchdog daemon with Intel 6300esb

  - by ACiD GRiM

  I've been searching for this on Google for sometime now and I have yet to find proper documentation on how to connect the kernel driver for my 6300esb watchdog timer to /dev/watchdog and ensure that watchdog daemon is keeping it alive. I am using RHEL compatible Scientific Linux 6.3 in a KVM virtual machine by the way Below is everything I've tried so far: dmesg|grep 6300 i6300ESB timer: Intel 6300ESB WatchDog Timer Driver v0.04 i6300ESB timer: initialized (0xffffc900008b8000). heartbeat=30 sec (nowayout=0) | ll /dev/watchdog crw-rw----. 1 root root 10, 130 Sep 22 22:25 /dev/watchdog | /etc/watchdog.conf #ping = 172.31.14.1 #ping = 172.26.1.255 #interface = eth0 file = /var/log/messages #change = 1407 # Uncomment to enable test. Setting one of these values to '0' disables it. # These values will hopefully never reboot your machine during normal use # (if your machine is really hung, the loadavg will go much higher than 25) max-load-1 = 24 max-load-5 = 18 max-load-15 = 12 # Note that this is the number of pages! # To get the real size, check how large the pagesize is on your machine. #min-memory = 1 #repair-binary = /usr/sbin/repair #test-binary = #test-timeout = watchdog-device = /dev/watchdog # Defaults compiled into the binary #temperature-device = #max-temperature = 120 # Defaults compiled into the binary #admin = root interval = 10 #logtick = 1 # This greatly decreases the chance that watchdog won't be scheduled before # your machine is really loaded realtime = yes priority = 1 # Check if syslogd is still running by enabling the following line #pidfile = /var/run/syslogd.pid Now maybe I'm not testing it correctly, but I would expecting that stopping the watchdog service would cause the /dev/watchdog to time out after 30 seconds and I should see the host reboot, however this does not happen. Also, here is my config for the KVM vm <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit sl6template or other application using the libvirt API. --> <domain type='kvm'> <name>sl6template</name> <uuid>960d0ac2-2e6a-5efa-87a3-6bb779e15b6a</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>Westmere</model> <vendor>Intel</vendor> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='ds'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='vme'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='rdtscp'/> <feature policy='require' name='ht'/> <feature policy='require' name='dca'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='pdpe1gb'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='pclmuldq'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='require' name='aes'/> </cpu> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/mnt/data/vms/sl6template.img'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> <controller type='usb' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/> </controller> <interface type='bridge'> <mac address='52:54:00:44:57:f6'/> <source bridge='br0.2'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:88:0f:42'/> <source bridge='br1'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <watchdog model='i6300esb' action='reset'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </watchdog> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain> Any help is appreciated as the most I've found are patches to kvm and general softdog documentation or IPMI watchdog answers.

  Read the article

• apcupsd on Linux does not report on APC BackUPS Pro 900

  - by lserni

  From what documentation I could find, the UPS should be (is!) supported by Linux and ought to work with apcupsd. I looked for specific problems such as the infamous Microlink protocol, and found none. I have found a feedback from a guy in UK that reports using this very model on a not-too-different OS version (his OpenSuSE 12.1, mine 12.3 x86_64). The USB port is detected, lsusb reports Bus 002 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply and lsusb -v -s002:003 confirms and expands: Bus 002 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x051d American Power Conversion idProduct 0x0002 Uninterruptible Power Supply bcdDevice 0.90 iManufacturer 1 American Power Conversion iProduct 2 Back-UPS RS 900G FW:879.L4 .I USB FW:L4 bNumConfigurations 1 Configuration Descriptor: [...] Interface Descriptor: [...] bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.00 bCountryCode 33 US bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 1134 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 100 Device Status: 0x0000 (Bus Powered) The kernel recognizes this and duly sets up crw------- 1 root root 180, 96 Nov 4 16:11 /dev/usb/hiddev0 As far as I know, everything is as it should be. I have put the standard configuration in /etc/apcupsd/apcupsd.conf (which is Unix-terminated, ASCII-only, no BOM (just in case)) UPSCABLE usb UPSTYPE usb DEVICE (I have also tried commenting out DEVICE, and setting a device of /dev/puppa results in an access attempt to /dev/puppa, not some /var/lib/dev/puppa or /dev/puppa\r\n). Yet, what apcaccess tells me is VERSION : 3.14.10 (13 September 2011) suse CABLE : USB Cable DRIVER : USB UPS Driver UPSMODE : Stand Alone STARTTIME: 2013-11-04 16:24:22 +0100 MODEL : STATUS : NOBATT LINEV : 000.0 Volts LOADPCT : 0.0 Percent Load Capacity BCHARGE : 000.0 Percent TIMELEFT : 0.0 Minutes MBATTCHG : 5 Percent MINTIMEL : 3 Minutes MAXTIME : 0 Seconds SENSE : Low LOTRANS : 000.0 Volts HITRANS : 000.0 Volts It doesn't recognize the model, and reports no battery (and no voltage). This confirms that it's not the Microlink problem, or it would report the battery status, if precious little else. If I disconnect the USB cable, I get an apcupsd message to the effect that communications have been lost; and I get the "communication restored" broadcast too, if I reconnect the cable. apcupsd is monitoring. So everything tells me that it should work -- only it doesn't. Does anyone spot what I'm missing?

  Read the article

• RewriteRules targeting a directory result in a gratuitous redirect [closed]

  - by MapDot

  I have a standard CMS-like RewriteRule set up in my .htaccess: RewriteRule ^(.+)$ index.php?slug=$1 Let's say I have a directory called "foo" in the root directory. For some reason, if you hit the page it causes a redirect: http://www.mysite.com/foo -- http://www.mysite.com/foo?slug=foo Removing the directory fixes the problem, but unfortunately, it's not an option. Does anyone know of a workaround?

  Read the article

• Firefox bookmark star in address bar

  - by Michael

  Is there any way to customize where to save my bookmarks when I hit start in the address bar? By default bookmarks are going to Unsorted folder and I want them to go to root or somewhere else.

  Read the article

• File Server Auditing/Logging

  - by Kvad

  Hi, I am currently setting up a file server with win2k8 server r2 (storage server) I was wondering is there something I can use to audit/log what happens? For example JSmith moved Folder1 to Root. JSmith created XYZ folder. etc. Directory Monitor doesn't show users (which is important) http://www.deventerprise.net/Projects.aspx Obviously something with low overhead would be awesome too. Thanks in advance

  Read the article

• Make environment variables available when running command as sudo

  - by Paul

  I am using Curl, and am having a problem trying to get it to recognize the $http_proxy environment variable when using sudo curl. I tried putting export http_proxy=.... in my /etc/profile and restarting the shell, to no avail. I would rather not use su -l and run the command while logged in as root.

  Read the article

• Monitor open files limits, etc

  - by marcog

  We've been hitting the max open files limit on a few services recently. There are also a bunch of other limits in place. Is there a way to monitor how close processes are to these limits so we can be alerted when it's time to either up the limits or fix the root cause? On the same note, is it possible to view a log of these events so we know when a crash occurs it's because of hitting one of these limits?

  Read the article

• Connection problem to MySQL on another machine on LAN

  - by Ankur

  I'm having trouble connecting to a MySQL database on the other machine on the same network. Could not connect to the specified instance. MySQL error number 1130 Host 'abc' is not allowed to connect to this MySQL server (Pinging ok time 1-3 ms ttl =128) I've checked out the following: TCP/IP enabled RegEdit under hlocal machine .... parameters .. maxUserpORT And timedelay.. Grant all . to 'root'@'Myipaddress'

  Read the article

• Postfix sendmail -bs shows no output - permissions?

  - by Tatu Ulmanen

  When I run the sendmail -bs command as root, I get the expected output: $ sudo sendmail -bs 220 mydomain.com ESMTP Postfix ehlo localhost 250-mydomain.com 250-PIPELINING 250-SIZE 15728640 250-ETRN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN But when I run the same command without sudo, I get no output at all and sendmail doesn't respond to any commands: $ sendmail -bs ehlo localhost quit wtf ^C $ How can I configure Postfix so that sendmail works for every user (or at least for some specific users)? I need this because SwiftMailer for PHP uses sendmail -bs for sending mails and fails when it can't find any output.

  Read the article

• Single nginx configuration for multiple sub domains

  - by Peter Smit

  I have the following directory structure for my websites: /var/www/sitename/subdomain/(public|log) e.g /var/www/stackoverflow.com/careers/public/index.html Can I make a single generic nginx configuration to do this? So that every domain is mapped to the right directory? I would not like to edit my nginx configuration for every website I add. The root domain can always be mapped to the www subdomain.

  Read the article

• Windows Server 2008 R2 network adapter stops working, requires hard reboot

  - by Geoff Dalgas

  TL;DR version: Turns out this was a Windows Server 2008 R2 kernel networking bug. After siccing Microsoft support on it, we (eventually) got an unpublished kernel hotfix from Microsoft to address it. If you, too, are experiencing mysterious low-level network driver failures requiring a reboot/bluescreen cycle, you might want that hotfix (or maybe Service Pack 1 whenever it is released, too.) We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps. Switch Virtualization providers On the off chance this was related to Hyper-V in some way (we do host Linux VMs on it), we switched to VMWare Server. No change. Switch host model We've reached the end of our troubleshooting rope and are now formally involving Microsoft support. They recommended changing the host model: http://en.wikipedia.org/wiki/Host_model http://technet.microsoft.com/en-us/magazine/2007.09.cableguy.aspx We did that, and.. we'll see.

  Read the article

• Mavericks not booting after successful installation over Lion (10.7.5)

  - by rpatil

  On my 2012 MacBook Pro (15 inch, non retina, i7, 10GB RAM) after successful installation when Mavericks tried to boot, it is freezing there with "Still waiting for root device" (Seen Using CMD + V during boot). Someone please help. My Mac is not usable anymore. Boots in safe mode but freezes in safe mode too. From safe mode reinstalled Mavericks but failed again with same error. If it can't be fixed please let me know if it can be reverted.

  Read the article

• Why there are two users showing in uptime command results?

  - by Osama Gamal

  Hi, When I ran the uptime on my MacBookPro machine I got the following result: Last login: Thu Jun 3 14:43:40 on ttys000 Osama-Gamal-MBP-2:~ iOsama$ uptime 14:49 up 7 days, 20:10, 2 users, load averages: 0.29 0.24 0.24 Why it lists that there are two users? is it normal? and who is the other user, is it the root user or what? PS: I'm using Mac OS X 10.6.3

  Read the article

• Nautilus cannot move to trash

  - by amorfis

  Thing takes place on ubuntu. I want to move a file to trash. I am not the owner of the file, but file belongs to root:samba, and I am member of samba group, and file permissions are rwxrw-r-- There is message "Cannot move file to trash, do you want to delete immediately?". Nothing more. Why can't I move it to trash?

  Read the article

• sendmail restart fail [exim abandoned: unknown,malformed, or incomplete option -L]

  - by PeopleInside

  When I restart Sendmail services, I see the following: [root@]# service sendmail restart Shutting down sm-client: [FAILED] Shutting down sendmail: [ OK ] Starting sendmail: [ OK ] Starting sm-client: exim abandoned: unknown,malformed, or incomplete option -L [FAILED] How can i do to fix this please? i'm on linux CentOS

  Read the article

• FreeBSD console broken?

  - by Kuroki Kaze

  It seems my FreeBSD console is misconfigured (i guess). I cannot use home button in command line, and in vi left arrow is switching me from edit to command mode, which makes editing a little difficult. How can I know what's wrong and fix it? I'm not a root, by the way, I just hope it's something with my profile configuration.

  Read the article

• phpMyAdmin causes php-fpm worker to restart (502 Bad Gateway)

  - by rndbit

  I am trying to set up a test site for myself. Everything works fine except phpMyAdmin. php installation loads my test site scripts, they work fine, however trying to load phpMyAdmin i get 502 Bad Gateway error. Judging from logs (that are not too helpful) it seems that php-fpm worker is crashing each time phpmyadmin is being accessed. No clue how or why.. Does anyone have any idea? nginx log: *3 recv() failed (104: Connection reset by peer) while reading response header from upstream, And php-fpm log: [07-Jun-2012 14:19:51] WARNING: [pool www] child 32179 exited on signal 11 (SIGSEGV) after 3.217902 seconds from start [07-Jun-2012 14:19:51] NOTICE: [pool www] child 32351 started My nginx conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; fastcgi_buffers 8 16k; fastcgi_buffer_size 32k; include /etc/nginx/conf.d/*.conf; server { listen 443 ssl; listen 80; server_name testsite.net www.testsite.net; ssl on; ssl_certificate /var/www/html/admin/ssl/certificate.pem; ssl_certificate_key /var/www/html/admin/ssl/privatekey.pem; ssl_session_timeout 1m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5:!kEDH; ssl_prefer_server_ciphers on; access_log off; location ~ \.php$ { root /var/www/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; } location / { root /var/www/html; index index.php; } } } php.ini is standard, with cgi.fix_pathinfo=0 php-fpm.conf: include=/etc/php-fpm.d/*.conf [global] pid = /var/run/php-fpm/php-fpm.pid error_log = /var/log/php-fpm/error.log log_level = notice php-fpm.d/www.conf: [www] listen = 127.0.0.1:9000 listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 10 pm.start_servers = 1 pm.min_spare_servers = 1 pm.max_spare_servers = 10 slowlog = /var/log/php-fpm/www-slow.log php_flag[display_errors] = on php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on

  Read the article

• Performance of Cluster Shared Volume file copy from SAN

  - by Sequenzia

  I am hoping someone can help me out with a strange issue. We are running a Microsoft Failover Cluster with Server 2008 R2 and an Equallogic PS4000 SAN. Our main configuration has 2 Dell Poweredge T710 Servers in the cluster. We have CSV and Quorm setup. The servers each have 10 Broadcom 1Gb NICs. Right now 4 of the NICS are on the iSCSI network for accessing the SAN. They use MPIO and the Dell HIT pack. We have 5 VMs running on each node and everything runs smooth. No noticeable performance issues or anything. From the SAN I can see the 4 iSCSI connections from each server to each volume (CSV and Quorm). Again, it seems to perform great. The problem I am running into is with backups. I have tried a few backup programs like backupchain and Veeam. The problem is both of them are very very slow to backup the VMs. For instance I have a 500GB (fixed disc) VHD that’s running on the cluster. It takes over 18 hours to backup that VHD and that’s with compression and depuping turned off which is supposed to be the fasted. We also have a separate server that is just for backups. It has a lot of directed attached storage. As part of the troubleshooting I decided to bring that server into the cluster as a node. It now has access to the CSV and can read from C:\clusterstorage\volume1 which is where our VHDs live. This backup server only has 2 NICs. 1 NIC is going to the iSCSI network and the other is just on the main network. It has Intel NICS in it without any sort of MPIO or teaming. So with the 3rd server now in the cluster I started doing some benchmarking. I have a test VHD that’s about 7GBs that’s stored in the CSV. I have tested file copying that VHD from all 3 servers to directed attached storage in the respective server. The 2 Dell servers that are the main nodes in the cluster (they house the VMs) are reading that file at about 20Mbs/Sec. Which at that rate is way to slow for the backups. The other server which only has 1 NIC to the SAN is reading at around 100Mbs/Sec. I spent a few hours on the phone with Dell today about this . We went through all kind of tests and he was pretty dumb founded. He really has no idea why that server with only 1 NIC is reading about 5 times as fast as the servers with 4 NICS and MPIO. We looked at the network utilization of the NICs while the file copy was going on. The servers with the 4 NICs had a small increase of activity during the file copy but they only went up to around 8-10% on all 4 NICs. The other server with the 1 NIC jumped up to over 80% during the file copy. I plan on doing some more testing after hours and calling Dell back tomorrow but I really am confused (and so is Dell’s support rep) why I cannot get faster file copy access to the CSV on those servers. Anyone have any input on this? Any feedback would be greatly appreciated. Thanks in advance.

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >