Search Results

Search found 11587 results on 464 pages for 'pseudo random numbers'.

Page 355/464 | < Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• Why do fonts sometimes look "fat" on Mac OS X?

  - by jtimberman

  Sometimes when resuming from suspend, the fonts in Mac OS X look "fatter" than normal. Unfortunately right now I can't get my Macbook Pro to exhibit the "normal" behavior for comparison, it has been abnormal yesterday and today. If I can get screenshots of what I think is 'normal', I'll add them. "Fixing" this has been random. I use an external monitor, and sometimes unplugging it and plugging back in, or even turning it off and back on has worked. Sometimes with the display attached (or not) detecting displays works. Sometimes logging out or rebooting entirely is what it takes. Displays used: Macbook Pro 15" built-in display Dell 27" LCD (2009 model) Software where I see this happen, at least most noticably: Firefox (screenshots below) iTerm Things MacIrssi (screenshots below) I am using Mac OS X 10.5.8. "Abnormal" view from MacIrssi with Inconsolata 16 pt. image full size "Abnormal" view from Firefox. Finally got it to switch back, though after resuming from suspend its back to "fat" :-(. image full size And 'normal' in Firefox:

  Read the article

• Can I get all active directory passwords in clear text using reversible encryption?

  - by christian123

  EDIT: Can anybody actually answer the question? Thanks, I don't need no audit trail, I WILL know all the passwords and users can't change them and I will continue to do so. This is not for hacking! We recently migrated away from a old and rusty Linux/Samba domain to an active directory. We had a custom little interface to manage accounts there. It always stored the passwords of all users and all service accounts in cleartext in a secure location (Of course, many of you will certainly not think of this a being secure, but without real exploits nobody could read that) and disabled password changing on the samba domain controller. In addition, no user can ever select his own passwords, we create them using pwgen. We don't change them every 40 days or so, but only every 2 years to reward employees for really learning them and NOT writing them down. We need the passwords to e.g. go into user accounts and modify settings that are too complicated for group policies or to help users. These might certainly be controversial policies, but I want to continue them on AD. Now I save new accounts and their PWGEN-generated (pwgen creates nice sounding random words with nice amounts of vowels, consonants and numbers) manually into the old text-file that the old scripts used to maintain automatically. How can I get this functionality back in AD? I see that there is "reversible encryption" in AD accounts, probably for challenge response authentication systems that need the cleartext password stored on the server. Is there a script that displays all these passwords? That would be great. (Again: I trust my DC not to be compromised.) Or can I have a plugin into AD users&computers that gets a notification of every new password and stores it into a file? On clients that is possible with GINA-dlls, they can get notified about passwords and get the cleartext.

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• .htaccess redirect to error page if port is not 80

  - by Momo

  I'm running a portable server through usb stick. The thing is I also have WAMP installed in my local machine and Apache somehow gets started on windows startup, because of some random reason which I don't recall now and it can't be changed. I want to prepare my portable server in situations like this, so closing httpd.exe from process and starting my portable server is not an option. Anyway, because of already active httpd.exe my portable server's WordPress site can only be accessed through localhost:81 - this is a problem as WP site is very dependent on the URL and I don't want to include the url with port on WP database. Here is what I want to do through .htaccess: On any path except for error.php file check if not port 80 If not port 80 redirect to /error.php?code=port It it possible for it to have priority over WP redirection or URL handling? In the error.php I provided info on how to manually close httpd.exe and such so my family and friends can access the portable site. It's sort of like a gallery and calender application for events and other such stuff... Please help? I'm I can't figure it out at all. I know others may not have apache already running, but I want to prepare for such a situation. Something like the following, but the following doesn't work. # BEGIN WordPress <IfModule mod_rewrite.c> <If "%{SERVER_PORT} = 80"> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </If> <Else> RewriteEngine On RewriteRule ^(error.php)($|/) - [L] RewriteRule ^(.*)$ /error.php?code=port [L] </Else> </IfModule> # END WordPress By the way, the portable server Server2Go automatically generates vhosts based o the hostname set on it's config file and changes ports if the port (e.g. 80) is already open.

  Read the article

• Weird mouse behaviour. Debian wheezy

  - by DevNoob

  When I move my mouse slowly over the desktop the pointer jumps often a few pixels (one or two) in the opposite direction of which I move my mouse. Horribly when trying to set the cursor around some semicolons in eclipse. I guess this is the result of a wrong set resolution of it. I suppose this is because the mouse was set initially really fast and even if I do xset 1/2 3, the mouse is just to fast and unprecise for me. It aready tried to configure the xorg.conf like this: Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "Auto" Option "Name" "Logitech G3" Option "Resolution" "2000" EndSection But with no effect. Maybe because there is no /dev/mouse. This ist the content of dev. Maybe you can tell me which one is the mouse. autofs block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dvd dvdrw fd fd0 full fuse fw0 hidraw0 hidraw1 hpet input kmsg log loop0 loop1 loop2 loop3 loop4 loop5 loop6 loop7 loop-control MAKEDEV mapper mcelog mem net network_latency network_throughput null nvidia0 nvidiactl oldmem port ppp printer psaux ptmx pts random rfkill root rtc rtc0 sda sda1 sda2 sda3 sda5 sda6 sda7 sda8 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sndstat sr0 stderr stdin stdout tty tty0 tty1 tty10 tty11 tty12 tty13 tty14 tty15 tty16 tty17 tty18 tty19 tty2 tty20 tty21 tty22 tty23 tty24 tty25 tty26 tty27 tty28 tty29 tty3 tty30 tty31 tty32 tty33 tty34 tty35 tty36 tty37 tty38 tty39 tty4 tty40 tty41 tty42 tty43 tty44 tty45 tty46 tty47 tty48 tty49 tty5 tty50 tty51 tty52 tty53 tty54 tty55 tty56 tty57 tty58 tty59 tty6 tty60 tty61 tty62 tty63 tty7 tty8 tty9 ttyS0 ttyS1 ttyS2 ttyS3 uinput urandom usb vcs vcs1 vcs2 vcs3 vcs4 vcs5 vcs6 vcs7 vcsa vcsa1 vcsa2 vcsa3 vcsa4 vcsa5 vcsa6 vcsa7 vga_arbiter vmci vmmon vmnet0 vmnet1 vmnet8 vsock watchdog xconsole zero So my question is: How do I setup my mouse correctly in Debian wheezy?

  Read the article

• KVM error with device pass through

  - by javano

  I am running the following command booting a Debian live CD passing a host PCI device to the guest as a test and KVM errors out; kvm -m 512 -boot c -net none -hda /media/AA502592502565F3/debian.iso -device pci-assign,host=07:00.0 PCI region 1 at address 0xf7920000 has size 0x80, which is not a multiple of 4K. You might experience some performance hit due to that. No IOMMU found. Unable to assign device "(null)" kvm: -device pci-assign,host=07:00.0: Device 'pci-assign' could not be initialized lspci | grep 07 07:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) I shoved an old spare NIC into my motherboard to test PCI pass through. I have searched the Internet with Goolge and found that errors relating to "No IOMMU found" often mean the PCI device is not supported by KVM. Does KVM have to support the device being "passed-through"? I though the point was to pass the device through and let the guest worry about it? Ultimately I want to pass-through a PCI random number generator, is this not going to be possible with KVM? Thank you.

  Read the article

• picking a linux compatable motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• Linux on HP Envy

  - by Oscar Godson

  OK, the Ubuntu forums aren't helping and I thought maybe you guys here could help. First off, does anyone know the best flavor of Linux to use on an HP Envy? what has the best support out of the box? If not, does anyone know how the hell to get the following to work on Ubuntu 10.04: The touchpad to work at all? Right now, right clicking doesnt work at at all, and left clicks dont work while you have another finger on the pad at all. It jumps all over. ALSO, the multi-touch isn't clickable, but it's for sure a multi-touch touchpad. Works in W7 and can do things like a MBP in W7 The computer feels like it's on fire... i think im missing some driver. Seems odd that the random meta keys like calc, email, brightness, right click, etc work, but not the touchpad? The video card seems fine, but i haven't tested compiz fully yet... Thanks so much to anyone who helps. i want to get back to linux after a couple years on Mac. :)

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

  Read the article

• How to calculate unweighted averages in Excel PivotTable?

  - by yonatron

  I often make PivotTables in which each row contains a number of per-person average measures. I then want to look at the unweighted column average for each measure, and usually make some kind of chart from these. Because my individual cells are often averaged from different numbers of data points, the Grand Total row ends up being a weighted average, which I’m not interested in. So I usually make my own average row a few rows above the table to use for my charts. That’s not too much work, but there’s another problem. I often add a few more people’s worth of data to the PivotTables’ source, then refresh the tables. This means my average row needs to be updated to encompass more rows from the PivotTable. Not a huge deal with one table, but when I have lots of them across lots of sheets, I have to do find/replace on a whole bunch of formulas. So: is there a way to automatically get unweighted column averages in a PivotTable, such that when the table is refreshed, the averages don’t change locations and encompass the newly added (or removed) data Thanks

  Read the article

• Centos Server/MySQL server problem

  - by Jake

  Hello all, I currently run a website we get about 15,000-20,000 hits a day. We currently run a very active forum, that is hosted using Vbulletin software. We have 4.5 Million Posts, 80,000 Threads, with about 11,000 members of which just under a third is active all the time. Now I am running a Intel Xeon Quad Core (2.13Ghz) with 4GB of RAM, Centos 5.5 and running DirectAdmin on the box to manage it. I also run the current stable version of Apache, MySQL, and php. This is the only site that is hosted on this machine. Now during random times of day sometimes when it gets busy the server load can get to like 20, but this can also happen when we only have like 200 users active too. I dont understand what is causing these problems. Sometimes I get pages that can generate in .2 seconds other times it takes like 5-8 seconds. I have customized the my.cnf file and that has not helped out anything, I didnt know where else to turn so if anyone has any suggestions please let me know. Thank You In advance.

  Read the article

• Samsung laptop randomly shuts down

  - by Dmatig

  I've rewritten this question because it turned into an indecipherable mess. I have a Samsung R560 laptop that is overheating, and shutting itself down under load consistantly. Thank you quickcel for reccomending me Speedfan to monitor my temps. Here they are (Load / Idle): (Ignore "Temp1 and Temp2", whatever sensors they are they'd always random, pretty sure they're broke). The load temperature is after just 5 minites of playing Fallout 3 - another 5 minutes and it (the GPU - 9600M GS) consistantly breaches the mid 90's then shuts down, so it's hard to get a good picture of it. I'm looking for some solution or way to decrease these temperatures, because they seem far too high even idle. I've tried: Opening up the case and clearing of all dust with compressed air. Updating drivers for my Graphics card Have purchased and am using a notebook cooler I don't want to: Undervolt / underclock (defeats the point of having a more expensive card) Use lower power / performance settings (again, i might as well have bought something cheaper) Is there anything else i can try (software or inexpensive hardware) that can help me fix this? Has anybody had a Samsung laptop and knows if this can be sorted under my warranty, and the turnaround time of sending it off (UK?)(it has always ran hotter than it should, but now at 6 months old is getting hot enough to power off)

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• MySQL partition "full"?

  - by gdea73

  I have a server that runs Debian 6.2, with Apache, PHP5, and MySQL. Well, I hadn't done anything with MySQL at all so far, just Apache and PHP; I must have installed it (mysql-server) at some point along the line, and I decided to login to the database for the first time a couple days ago as I was considering using the database for a future website project. I noticed that the "root" user had a password, and I didn't recall having set one. My usual root password was incorrect. So I attempted to reset the password. sudo service mysql stop (stopped successfully) sudo /usr/bin/mysqld_safe --skip-grant-tables --skip-networking & started successfully, from what I can tell. However, mysql itself returns "Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld,sock' (2)", and additionally sudo service mysql start returns "/etc/init.d/mysql: ERROR: The partition with /var/lib/mysql is too full! ... failed!" df -h tells me that / is 26% used, a 20GB partition, and /home, roughly 900GB, has only 5% usage. On a potentially related note, I've been experiencing random hangs since I noticed this problem, my tty2 randomly froze several times while idle, and the entire system is suddenly unstable. gnome-terminal also does not open. (Gnome-terminal apparently works now, disregard that part, but the server is still being somewhat unstable, I randomly lost connection when I was SSHed into it from my laptop, twice now.)

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• port forwarding problem

  - by Claudiu

  I want to set up an svn server on my computer, so it's available from anywhere. I think I set up the repository correctly, using CollabSVN. If I go to Repo-Browser with TortoiseSVN and point it to svn://localhost:3690, it shows the proper repository. The problem now is that I'm behind a router. My local IP is 192.168.1.45 . Doing svn://192.168.1.45:3690 also works. My global IP is, say, x.x.x.x. Just doing svn://x.x.x.x:3690 doesn't work, which makes sense, since I have to set up port forwarding. I'm using a Verizon router. Using their web interface (on 192.168.1.1) I added the following port forwarding rule: IP Address forward to: 192.168.1.45 Source Ports: Any Dest Ports: 3690 Forward to: 3690 Protocol: TCP However, even after applying this rule, going to svn://x.x.x.x:3690 doesn't work. It takes a few seconds to fail, then says that the connection couldn't be established because the server connected to didn't respond properly after a period of time. What's interesting is that a random port, like svn://x.x.x.x:36904 fails immediately, saying that the target machine actively refused the connection. So I figure that the forwarding rule did something, but not fully what was necessary. Any ideas on how to get this working? The router model is MI424-WR and the firmware version is 4.0.16.1.56.0.10.12.3. UPDATE: I also tried setting destination port to 45000, and still forwarding to 3690, in case something was wrong w/ the lower-numbered ports, but to no avail. I also tried port 80 to port 3690, still all in vain.

  Read the article

• Cisco IOS BVI ACL: Only allow established UDP

  - by George Bailey

  Related: Cisco IOS ACL: Don't permit incoming connections just because they are from port 80 I know we can use the established keyword for TCP.. but what can we do for UDP (short of replacing a Bridge or BVI with a NAT)? Answer I found out what "UDP has no connection" means. DNS uses UDP for example.. named (DNS server) is lisenting on port 53 nslookup (DNS client) starts listening on some random port and sends a packet to port 53 of the server and notes the source port in that packet. nslookup will retry 3 times if necessary. Also the packets are so small that it does not have to worry about them coming in the wrong order. If nslookup receives a response on that port that comes from the servers IP and port then it stops listening. If the server tried to send two responses (for example a response and a response to the retry) then the server would not care if either of them made it because the client has the job to retry. In fact.. unless ICMP 3/3 packet gets through the server would not know about a failure. This is different from TCP where you get connection closed or timed out errors. DNS allows for an easy retry from the client as well as small packets.. so UDP is an excellent choice because it is more efficient. In UDP you would see nslookup sends request named sends answer In TCP you would see nslookup's machine sends SYN named's machine sends SYN-ACK nslookup's machine sends ACK and the request named's machine sends the response That is much more than is necessary for a tiny DNS packet

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Making libmagic/file detect .docx files

  - by Jonatan Littke

  As seen elsewhere, docx, xlsx and pttx are ZIPs. When uploading them to my web application, file (via libmagic andpython-magic) detects them as being ZIP. I store the contents of the file as a blob in the database, but naturally I don't want to trust the user with what kind of file type this is. So I would like to trust file for and automatically generate a filename during download. I know one can modify /etc/magic but the format (magic(5)) is way too complicated for me. I found a bug report on the issue at Debian bugs but since it's from 2008 it doesn't seem to be fixed any time soon. I guess my only other alternative is to indeed trust the user (but still store the contents as a blob) and only check the file extension based on the file name. This way I can disallow some extensions and allow others. And when the user re-downloads his file, he can have it in whatever way he uploaded it. But this solution is insecure if the file is shared with others, since you can simply rename the file to allow uploading it. Any ideas? Lastly, I found a list of magic numbers for docx etc, but I'm unable to convert these into the magic(5) format.

  Read the article

• Upstart multiple instances of service not working

  - by Dax

  I started playing with MongoDB on Lucid. Now I would like to run a DB and Config server on the same box. They both use the same binary to launch, but with different config files and running on different ports. All directories for log and lib is split so one goes to mongodb and the other to mongoconf. Each process can be started without any problems on their own. start mongodb stop mongodb start mongoconf stop mongoconf But if I try to start both, the second one would just start and exit. Using 'initctl log-priority debug' I got the following in the logs. Jan 6 12:44:12 mongo4 init: event_finished: Finished started event Jan 6 12:44:12 mongo4 init: job_process_handler: Ignored event 1 (1) for process 5690 Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) main process (5690) terminated with status 1 Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) goal changed from start to stop Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) state changed from running to stopping man 5 init shows that you can use instance names to differentiate the two. I tried using 'instance mongoconf' in the on upstart script and 'instance mongodb' in the other one, and it still fails. I can manually start the other process, so there is definitely no conflicts on port numbers or directories. Any ideas on what to try or how to get output on why it is 'terminated with status 1'? Thanx

  Read the article

• How to configure CISCO switch 2960 for port-based address allocation on a single port only?

  - by Jack

  CISCO 2960 allows you to configure so-called Port-Based address allocation. It makes the switch to associate IP address it is giving out via DHCP with port-identifier, which is random, switch created identifier. In practice it means that any machine connected to such configured port will always get the same IP address, regardless of what that machine's MAC address is. I want to have that feature configured on --some ports-- only. But no matter what commands I try it seems that this can only be done for all ports, all for none. Even though CISCO manual seems to indicate there's both global and per-port command to enable that. Here are relevant commands from CISCO manual: configure terminal ip dhcp use subscriber-id client-id (this configures the DHCP server to globally use the subscriber ID as the client ID on all incoming DHCP messages) interface FastEthernet0/1 ip dhcp server use subscriber-id client-id (Optional: Configures the DHCP server to use the subscriber ID as the client ID on all incoming DHCP messages on the interface) but it appears if I configure only per-interface than there's no effect at all, if I configure globally and per interface - CISCo behaves as if all ports were configured to use that feature. Any ideas?

  Read the article

• GNU Screen and Finch Not Playing Nicely

  - by Sean M

  I use finch for instant messaging, and for persistence, finch is one of the things that runs in my screen session. There are three main computers that I access my screen session from, and each works at a different screen resolution. Because of the different resolutions, when I switch computers, I use screen -rd to attach to my screen session. Using screen -x results in problems. When I attach to the session, though, finch experiences display problems. I have to wait up to several minutes for finch to become responsive - it doesn't redraw properly at all. Trying to switch between chats just writes ^n and ^p, or ^(1-9) for numbers. It fixes itself after some time. Using ctrl-l does not help. Switching back and forth between screen windows does not help. This is an annoying behavior that I don't experience with any other applications running in screen. Is this a bug in screen or finch, and if not, what can I change about my configuration to correct it ? (would appreciate it if "finch" could be used as a tag for this instead of or in addition to "pidgin")

  Read the article

• Torrent upload ratio not updated on Synology DS212+

  - by user179271

  I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

  Read the article

• How to turn off Tomcat logging in Eclipse?

  - by kirdie

  I develop a Vaadin project in Eclipse that I start through Tomcat 6 which gets started directly by Eclipse. Tomcat prints an enormous amount of log messages though on each start which makes it hard to see the output of my own Application. I have already replaced all log levels in tomcat6/conf/logging.properties by WARNING (e.g. java.util.logging.ConsoleHandler.level = WARNING) but I still get many INFO messages. How can I turn this off or restrict the log messages to WARNING? An example of the messages Okt 26, 2012 12:16:36 PM org.apache.catalina.core.AprLifecycleListener init INFO: Loaded APR based Apache Tomcat Native library 1.1.24. Okt 26, 2012 12:16:36 PM org.apache.catalina.core.AprLifecycleListener init INFO: APR capabilities: IPv6 [true], sendfile [true], accept filters [false], random [true]. Okt 26, 2012 12:16:36 PM org.apache.tomcat.util.digester.SetPropertiesRule begin WARNING: [SetPropertiesRule]{Server/Service/Engine/Host/Context} Setting property 'source' to 'org.eclipse.jst.j2ee.server:saim' did not find a matching property. Okt 26, 2012 12:16:37 PM org.apache.coyote.http11.Http11AprProtocol init INFO: Initializing Coyote HTTP/1.1 on http-8080 Okt 26, 2012 12:16:37 PM org.apache.coyote.ajp.AjpAprProtocol init INFO: Initializing Coyote AJP/1.3 on ajp-8009 Okt 26, 2012 12:16:37 PM org.apache.catalina.startup.Catalina load INFO: Initialization processed in 879 ms Okt 26, 2012 12:16:37 PM org.apache.catalina.core.StandardService start INFO: Starting service Catalina Okt 26, 2012 12:16:37 PM org.apache.catalina.core.StandardEngine start INFO: Starting Servlet Engine: Apache Tomcat/6.0.32 Okt 26, 2012 12:16:37 PM org.apache.coyote.http11.Http11AprProtocol start INFO: Starting Coyote HTTP/1.1 on http-8080 Okt 26, 2012 12:16:37 PM org.apache.coyote.ajp.AjpAprProtocol start INFO: Starting Coyote AJP/1.3 on ajp-8009 Okt 26, 2012 12:16:37 PM org.apache.catalina.startup.Catalina start INFO: Server startup in 568 ms

  Read the article

< Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >