Search Results

Search found 11759 results on 471 pages for 'isolation level'.

Page 357/471 | < Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >

• How to completely disable IPv6 for loopback interface on RHEL 5.6

  - by Marc D

  I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

  Read the article

• Log and debug/decrypt an windows application's HTTPS traffic

  - by cweiske

  I've got a proprietary windows-only application that uses HTTPS to speak with a (also proprietary, undocumented) web service. To ultimately be able to use the web service's functionality on my linux machines, I want to reverse-engineer the web service API by analyzing the requests sent by the application. Now the question: How can I decrypt and log the HTTPS traffic? I know of several solutions which don't apply in my case: Fiddler is a man-in-the-middle HTTPS proxy which I cannot use since the application doesn't support proxies. Also, I do not (yet) know if it works with self-signed server certificates, which I doubt. Wireshark is able to decrypt SSL streams if you have the server's private certificate, which I don't have. any browser extension since the application is not a browser If I remember correctly, there have been some trojans that capture online banking information by hooking into/replacing the window's crypto API. Since the machine is mine, low level changes are possible. Maybe there is a non-trojan (white-hat) network log application out there which does the same? There is a blackhat presentation with some details available to read. They refer to Microsoft Research Detour for easy API hooking.

  Read the article

• Upgrade SQLServer 2008 hardware

  - by John

  Forgive me if I'm not able to be totally clear here. It is not intentional, I'm a senior level developer in a very small company having to act like a manager at the moment. Anyway, the story is that we have 2 older dell servers with SQL Server 2008 Standard in a "cluster". I put that in quotes because I'm still not 100% clear what that means. We have 2 brand new blade servers and want to move the existing databases to the new hardware. Ok, so here is the gotcha. We need to do this with little or no down time. I'm being told that we can evict the passive node, then pull in one of the new servers. But I'm also being told that this is a dangerous step because something could go wrong that would cause the cluster to fail and then we would be left with nothing because the active server would not be able to come back up. Does anyone have any thoughts on how to handle this? I'm being told that the only way to ensure success is to have at least a day of down time where we bring up a new cluster on the new hardware and then migrate the databases 1 by 1.

  Read the article

• CentOS: Init scripts failing to start for some unknown reason

  - by user705142

  I'm running CentOS 6.2 - I've just migrated some applications over to a failover server, and copied their init scripts into /etc/init.d. I've made them executable, added them to chkconfig, with chkconfig -add, set their levels, made sure they're residing in /etc/rc.d/ - made sure I can execute them from rc2.d etc. The permissions are the same on both servers. They're also running in the same order as on the primary server Yet on reboot they don't start. Any ideas? The offenders are these: jetty 0:off 1:off 2:on 3:on 4:on 5:on 6:off smart 0:off 1:off 2:on 3:on 4:on 5:on 6:off /etc/init.d: -rwxr-xr-x. 1 root root 14456 Mar 13 20:21 jetty -rwxrwxrwx. 1 root root 5829 Mar 29 09:58 smart /etc/rc.d/rc3.d lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99jetty -> ../init.d/jetty lrwxrwxrwx. 1 root root 11 Mar 26 17:12 S99local -> ../rc.local lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99smart -> ../init.d/smart I've checked, and I'm in run level 3. I've checked their logs, and there's no indication that that they've been started. I can start them manually easily - and other services are starting normally. I'm completely out of ideas really.

  Read the article

• Restrict Computer or Users from Internet but allow access to intranet and Windows Update / ePO?

  - by MoSiAc

  So this may be impossible but I've been asked to try and find something about it. So far nothing I have found is possible. I need to restrict specific machines or user accounts from regular Internet access but let them have access to the intranet portion of our network. I do not have Active Directory control, nor does anyone at my local workplace (corporate control in a different state). I have tried going through IPsec and doing this per local machine, but that system seems to have been removed from the images that are installed on these machines so that is out. So far the only other option I can think of is assigning the machines a specific ip address and removing their gateway access. This would probably work but the machines need to be able to receive updates that are being pushed to them through ePO and LanDesk. I would really like to do this on the user level because then if I need to do tech work to the machine and need internet access I can get to it but a "special" user could login and not be able to get into anything.

  Read the article

• How do you apply proxy settings per computer instead of per user?

  - by Oliver Salzburg

  So far, I've used a user group policy object utilizing Internet Explorer maintenance to set a proxy for the user in IE. We have now deployed the Enterprise Client (EC) starter group policy to our domain and this policy affects this behavior. The EC group policy uses the policy Make proxy settings per-machine (rather than per-user). This policy describes itself as: This policy is intended to ensure that proxy settings apply uniformly to the same computer and do not vary from user to user. Great! This seems to be an improvement over my previous setup. If you enable this policy, users cannot set user-specific proxy settings. They must use the zones created for all users of the computer. What zones and where do I configure the proxy settings for them? I assumed the policy would simply take the user settings and apply them, but that's not what's happening. Now no proxy server is set at all. So my previous settings obviously no longer have any effect. So far, I've only come up with solutions that involved direct manipulation of the Windows registry. Which is fine, I guess, but the way the proxy is configured for users makes it appear as if there could be a higher level approach.

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• Recommended programming language for linux server management and web ui integration.

  - by Brendan Martens

  I am interested in making an in house web ui to ease some of the management tasks I face with administrating many servers; think Canonical's Landscape. This means doing things like, applying package updates simultaneously across servers, perhaps installing a custom .deb (I use ubuntu/debian.) Reviewing server logs, executing custom scripts, viewing status information for all my servers. I hope to be able to reuse existing command line tools instead of rewriting the exact same operations in a different language myself. I really want to develop something that allows me to continue managing on the ssh level but offers the power of a web interface for easily applying the same infrastructure wide changes. They should not be mutually exclusive. What are some recommended programming languages to use for doing this kind of development and tying it into a web ui? Why do you recommend the language(s) you do? I am not an experienced programmer, but view this as an opportunity to scratch some of my own itches as well as become a better programmer. I do not care specifically if one language is harder than another, but am more interested in picking the best tools for the job from the beginning. Feel free to recommend any existing projects except Landscape (not free,) Ebox (not entirely free, and more than I am looking for,) and webmin (I don't like it, feels clunky and does not integrate well with the "debian way" of maintaining a server, imo.) Thanks for any ideas!

  Read the article

• Document Map in MS Word 2007 going bonkers

  - by rzlines

  I'm working on a large project report in Microsoft Word 2007 and have been using the document map to generate the index. I have been carefully selecting the headers that need to be added to the document map but I saved the document and opened it up today to work on it - the document map has added whatever it pleases there. This is a temporary fix from a post that I found after extensive searching that works, but when I save and close the document and open it up again I face the same dilemma: I have noticed that when Word stuffs up the document map after opening the file, I can undo this by using the UNDO button. Word calls it ’Autoformat’. I have also fixed a file that has had the document map screwed permanently (i.e saved with it) by selecting all (CTRL+A),selecting the PARAGRAPH drop down menu in the HOME TAB and in the OUTLINE drop down box, selecting ’Body Text’. This removed all the problems and did not seem to affect my outline level paragraph headings. This is also another temporary fix but I have to be on my toes not to let Word auto format at the start of the document. I also can't afford to entirely turn off auto format as I need it. I’ve solved this problem for me. When you open the file, a progress bar at the bottom first says Opening (ESC to Cancel) and then it says Word is formatting the document (ESC to Cancel). If I cancel the second process, TOC fine. No cancelling, TOC screwed. Can anyone work out how to switch off the autoformatting? This is the post in which i found for the temporary fix

  Read the article

• Explorer.exe hangup during move large file into external drive

  - by PiotrK

  During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Track kids browsing history even when they know how to clear it manually

  - by Darren Newton

  I have a colleague with two teenage boys (yes, cue cliche's about 'I have this friend see...') He's currently having issues with them browsing pr0n and wants to do a little spying on their browsing (I'm staying clear of the philosophies/ethics on this.) The kids are savvy enough to clear their browsing history when they're done. As I'm his goto for IT he has asked me if there is a way to keep a hold of the browsing history. The family uses Macs, and the kids surf with Safari. I know that browsing history is kept here ~/Library/Safari/History.plist. I figure there should be a way to write either an AppleScript or other script (Python/Ruby/Bash) that can backup this file to a different location (/opt/local/history, etc.) Since the kids know to clear their history when they're done should the file be periodically backed up with something similar to a cron job or something like Hazel? While that could work it seems like it would create a ton of little incremental backups. Or is it possible to 'watch' ~/Library/Safari/History.plist and incrementally add changes to a backup file (saving a diff so to speak) but not lose any data? Any ideas/solutions appreciated. UPDATE/EDIT: Got the word from concerned dad that the oldest uses Firefox on a different PC, so the OpenDNS solution (preferably at the router level) is the best answer so far as it would capture usage for the whole house.

  Read the article

• How to configure default text selection behavior in Windows XP, 7? (eg. mouse click selects entire word vs. mouse click inserts an active cursor)

  - by Mouse of Fury

  I find the mouse click behavior of Windows XP and Windows 7 annoying and intrusive. I don't remember Windows NT being quite this bad, or MacOS 7 - 10 which I used in the nineties. When I'm using a browser and I click on a text field - for example, the address bar, or a search box - the first thing which happens is the entire field is selected.Subsequent clicks seem to select parts of words, often deciding arbitrarily to exclude or include adjacent punctuation. The same in Excel and other apps, and when trying to rename files, so I'm assuming this behavior comes from a system-wide text handling routine. I frequently want to edit text, cut out or replace odd parts of the insides of words or chunks of sentences, and often find that to get a simple cursor to insert I have to click the mouse up to 4 times in succession. I've had to do a lot of this recently and it has been driving me insane. Is there a place at the system level where this can be configured? In a perfect world, I'd like a single click on a new text area to insert a cursor point, and a rapid double click to select the entire area. Words or text within the area could be selected by inserting a cursor, holding down the mouse button and dragging to the exact point where I want the selection to end - even if that's in the middle of a word. No, I don't need or want Windows to "smart select" a word or sentence for me. I've looked in the Mouse and Accessibility Options control panels (Windows XP). Haven't found anything even close. Thanks -

  Read the article

• Distributed storage and computing

  - by Tim van Elteren

  Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

  Read the article

• What is the reason for this DNSSEC validation failure of dnsviz.net?

  - by grifferz

  On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

  Read the article

• Reusing slot numbers in Linux software RAID arrays

  - by thkala

  When a hard disk drive in one of my Linux machines failed, I took the opportunity to migrate from RAID5 to a 6-disk software RAID6 array. At the time of the migration I did not have all 6 drives - more specifically the fourth and fifth (slots 3 and 4) drives were already in use in the originating array, so I created the RAID6 array with a couple of missing devices. I now need to add those drives in those empty slots. Using mdadm --add does result in a proper RAID6 configuration, with one glitch - the new drives are placed in new slots, which results in this /proc/mdstat snippet: ... md0 : active raid6 sde1[7] sdd1[6] sda1[0] sdf1[5] sdc1[2] sdb1[1] 25185536 blocks super 1.0 level 6, 64k chunk, algorithm 2 [6/6] [UUUUUU] ... mdadm -E verifies that the actual slot numbers in the device superblocks are correct, yet the numbers shown in /proc/mdstat are still weird. I would like to fix this glitch, both to satisfy my inner perfectionist and to avoid any potential sources of future confusion in a crisis. Is there a way to specify which slot a new device should occupy in a RAID array? UPDATE: I have verified that the slot number persists in the component device superblock. For the version 1.0 superblocks that I am using that would be the dev_number field as defined in include/linux/raid/md_p.h of the Linux kernel source. I am now considering direct modification of said field to change the slot number - I don't suppose there is some standard way to manipulate the RAID superblock?

  Read the article

• Sending e-mail on behalf of our customer(s), with Postfix

  - by NathanE

  We send e-mail on behalf of our customers, via our own SMTP services. It's always been a problem for us because usually our "spoofing" of their source address results in the mails being caught in spam traps. This hasn't been a problem in the past due to the small volume and low importance of these mails that we sent. However this requirement has recently changed and we need to fix this issue. We realise that fundamentally our application is sending e-mail incorrectly, as per this post: Send email on behalf of clients However, we would like to resolve the problem at the SMTP server level. We have deployed a server running Postfix. Is it possible to have Postfix automatically adjust the mail headers so that we get this "Sent on behalf of" behaviour? I figure it should just be a case of Postfix noticing that the FROM address is the spoofed (i.e. a domain that is not mentioned in its config anywhere) and therefore inject/replace the appropriate headers to get the desired effect. Thanks.

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• Software RAID 1 Configuration

  - by Corve

  I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• PC dies when running at 100% CPU

  - by user155631

  I recently wrote some Java code to generate images of the Mandelbrot set (fractal). I made use of the new Fork/Join facility in Java 7 to run separate threads on all four cores (2 real, 2 virtual)simultaneously, using a large number of iterations for greater accuracy. The problem is, the process runs fine for about a minute, and then it's as if someone has pulled the plug and the PC just dies. I thought it must be the CPUs overheating, so I ran Real Temp to monitor the temperature. It's an Intel i3 processor. I can see the temperature creeping up to 70 degrees, and then it seems to level off there and run for about another 30 seconds before dying. According to Real Temp, there's still a gap of 35 degrees between the actual temperature and TJ max. I also tried disabling "CPU TM function" in the BIOS, but the problem still occurs. A colleague suggested that it might be a power supply problem, so I borrowed a more powerful PSU (can't remember what wattage it was, but it's higher than mine which is 500W). The exact same thing still happens though. Is anyone able to suggest what the problem might be, or what I can try next?

  Read the article

• Apache https is slsow

  - by raucous12

  Hey, I've set apache up to use SSL with a self signed certificate. With http (KeepAlive off), I can get over 5000 requests per second. However, with https, I can only get 13 requests per second. I know there is supposed to be a bit of an overhead, but this seems abnormal. Can anyone suggest how I might go about debugging this. Here is the ab log for https: Server Software: Apache/2.2.3 Server Hostname: 127.0.0.1 Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,DHE-RSA-AES256-SHA,4096,256 Document Path: /hello.html Document Length: 29 bytes Concurrency Level: 5 Time taken for tests: 30.49425 seconds Complete requests: 411 Failed requests: 0 Write errors: 0 Total transferred: 119601 bytes HTML transferred: 11919 bytes Requests per second: 13.68 [#/sec] (mean) Time per request: 365.565 [ms] (mean) Time per request: 73.113 [ms] (mean, across all concurrent requests) Transfer rate: 3.86 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 190 347 74.3 333 716 Processing: 0 14 24.0 1 166 Waiting: 0 11 21.6 0 165 Total: 191 361 80.8 345 716 Percentage of the requests served within a certain time (ms) 50% 345 66% 377 75% 408 80% 421 90% 468 95% 521 98% 578 99% 596 100% 716 (longest request)

  Read the article

• SAFE MODE Restriction in effect. The script not allowed to access directory owned by uid

  - by user57221

  I am running a dedicated server with multiple websites. I have created a global directory for common scripts for all websites, rather than repeating them in every website directory. How can I make this global directory accessible for all website. I am getting following error. Warning: require_once() [function.require-once]: SAFE MODE Restriction in effect. The script whose uid is XXXX is not allowed to access /vhosts/globallibrary/Zend/Application.php owned by uid XXXX I have change the ownership of global directory for X website. so it works fine for X website. latter I added another website Y Now I am getting the same error again. If I change the CHOWN for Y website then X website will have the same error. I don't want to disable the safemode restriction. Is there a work around, so that this global dir will be accessible by all website. I am getting following error in my browser when I try to access global directory. Global directory is on same level as all other websites. Is this a good practice to enable safemode for websites?

  Read the article

• what is the reason behind window service stopped ,whether its due to LAN problems or any other issues

  - by Steve

  I have a windowservice which named Trunk which stopped one day i just want to know the reason behind it? this is an entry in the logs, Nov 15 17:54:04.318 :Trunk-1516:Trunk:handle_control_event:Received CTRL_LOGOFF_EVENT, ignore it Nov 25 15:54:52.157 :Trunk-1516:Trunk:ERROR - Process Restart Count (5) Exceeded for:C:\Program Files\secon\11.1.4\bin\vmd Nov 25 15:54:52.157 :Trunk-1516:Trunk:Stopping Trunk ... Nov 25 15:54:52.314 :Trunk-1516:Trunk:Shutting down, signaled C:\Program F Nov 20 15:54:20.345 :SCBridge.RegisterBridge:Exception in method: ScUtility.ScCommandException (0xa08990002): Exception from HRESULT: 0xa08990002 Supplemental Information: None available. at ScServer.ScServiceProcessorRegistryManager.Attach(String serviceProcessor, ScClientInformation clientInfo, FORCE_ATTACH_SPEC forceAttachToMaster) at ScServer.ScServiceProcessorRegistry.Attach(String serviceProcessor, Object clientInfo) at ScServer.ScServiceProcessorRegistry.Attach(String serviceProcessor) at ServerControlInterface.SCBridge.RegisterBridge(String SPName) for system APOLLOSP0 attempting to attach and register with the Bridge i had seen service is registered with specific account, so i thought that user logged off from the machine that may be the reason behind it or any LAN disconnection problem . But Having taken another look at the above entry we seem to have a constant failure being generated in vmd which causes Trunk to detect vmd requires a restart. Most of the time it works OK and the restart count is anything up to 4. In this case the Trunk log confirms that the Restart Count is 5 and so is considered to be exceeded. Presumably, this triggers the termination of the other services and Trunk is actually doing its job.So, coould this just be a timing issue and we need to increase the tolerance level (i.e restart count) or do we need to address the 0xa08990002 error in vmd?

  Read the article

< Previous Page | 353 354 355 356 357 358 359 360 361 362 363 364  | Next Page >