Search Results

Search found 12611 results on 505 pages for 'matlab figure'.

Page 359/505 | < Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >

• Windows Server 2003 (w/Exchange) move to new machine

  - by James Booker

  I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

  Read the article

• Games on windows 8 in bootcamp lag even on lowest graphics

  - by Jackson Gariety

  I've been playing Crysis 2 and Skyrim on my Retina MacBookPro (10,1) for months now. The two games used to run super smoothly even on nearly maxed out settings. This laptop has an Nvidia GeForce GT 650M graphics card inside, it runs great. But I recently replaced my Windows 8 consumer preview with the retail copy, and since then, 3D games lag in this odd way, no matter what the graphics settings. Every second Skyrim and Crysis alternates between running smoothly and lagging. It's a cyclical lag that comes and goes like clockwork. I can turn the graphics down to 800x600 with no antialiasing and low texture quality, and it runs much smoother on the "up" motion of the cycle, but every second it moves back into this lag spike. I've tried installing beta graphics drivers, re installing the operating system, re installing the bootcamp support software, and freeing up space (I have about 20 GB free). I can't figure out what suddenly caused this other than some obscure difference between the consumer preview and the retail version. What can I try? Is my video card failing? Are there some other drivers I can install? This isn't normal lag from maxing out the card, it

  Read the article

• Ubuntu 12.04 can't boot after installing with software RAID 1

  - by Bill

  I've been trying to install Ubuntu with software RAID on my server and there is obviously something that I don't understand about the process. This is the guide that I followed: https://help.ubuntu.com/11.04/serverguide/advanced-installation.html I have two identical 1 TB disks in my server. I went through the initial install process and manually set up my partitions. On each disk I set up: (1) 100 MB partition for EFI boot (I didn't originally have this but added it based on a forum post I found after my original install failed to boot, I ended up with EFIboot since that was what the 'guided partitioning' decided to do) (1) 970 MB partition for / (1) 30 MB partition for swap I then created new RAID 1 disks combining the two partitions, one from each disk, such that each partition is mirrored. I then configured their usage as stated above. After saving the configuration I said yes to boot in a degraded state. The rest of the setup went normally, no errors of any kind. I saw GRUB being installed and again no errors. However, after rebooting the server I get the dreaded 'Insert boot media' and nothing happens. I loaded up the recovery disk and the mdadm configuration looks correct. md0 is my EFIBoot partition md1 is my \ partition using ext4 md2 is my swap partition Running file -s /dev/md0 doesn't indicate that GRUB is there and so I attempted to reinstall GRUB using the recovery disk. I selected the md0 disk and it appeared to install just fine. Running file -s /dev/md1 shows the error needs journal recovery, I'm not sure if that's related or not or how to fix that. Rebooting gives me the same problem, no boot media found. I've searched around the internet but can't figure out what to do next or more importantly how to troubleshoot what exactly is going wrong. Thanks!

  Read the article

• Need a helpful/managed VPS to help transition from shared hosting

  - by Xeoncross

  I am looking for a VPS that can help me transition out of a shared hosting environment. My main OS is Ubuntu, although I am still new to the linux world. I spend most of my day programming PHP applications using a git over SSH workflow. I want PHP, SSH, git, MySQL/PostgreSQL and Apache to work well. Someday after I figure out server management I'll move on to http://nginx.org/ or something. I don't really understand 1) linux firewalls, 2) mail servers, or 3) proper daily package/lib update flow. I need a host that can help with these so I don't get hit with a security hole. (I monitor apache access logs so I think I can take it from there.) I want to know if there is a sub $50/m VPS that can help me learn (or do for me) these three main things I need to run a server. I can't leave my shared hosts (plural shows my need!) until I am sure my sites will be safe despite my incompetence. To clarify again, I need the most helpful, supportive, walk-me-through, check-up-on-me, be-there-when-I-need you VPS I can get. Learning isn't a problem when there is someone to turn too. ;)

  Read the article

• troubleshooting postifx -> exchange connection issues

  - by Systemspoet

  I have three linux-based mail routers that run postfix and relay mail to our on-premise exchange server as well as to outlook.com, splitting the mail based on ldap atttributes. What I've observed sporadically since upgrading this spring from Exchange 2007 to 2010 is that all three of the mail relays will, for about 20 minutes, fail to connect to exchange. Postfix logs it as "lost connection with exchange.contosso.edu" ; this problem almost always occurs to all three mail relays at the same time, and lasts for slightly under 20 minutes. If I can catch it while it's occuring, and I manually do "telnet exchange.contosso.edu 25" from one mail relay and force a message through (helo, mail from, rcpt to, data, etc), then it clears that relay up. The exchange "server" is actually two machines with the HT role on them, load balanced via windows NLB. I've worked pretty hard to figure out what's happening from the postfix side and I can't see any evidence of any misbehavior. My question is, how do I attack the problem from the exchange side? Is there a connection log, or a debug setting, or something I can do to log all of the inbound connections and tell me what's causing exchange to drop them?

  Read the article

• Access 2010 datasheet view only/relationships unavailable

  - by Luis

  I'm relatively new to MS Access in general and just started working with Access 2010. I've created a new web database with a few tables that I need to relate. First problem: For the life of me, I can't view anything in any view other than datasheet view; everywhere I would expect to be able to change the view, only datasheet view is available. Second problem: I can't change the primary key(s). Presumably I would be able to do this if I could get out of datasheet view and into design view. Third problem: The 'Relationships' button is greyed out. I know these appear to be really simple things but I've been looking for much more time than I'd like to admit trying to figure out how to get unstuck. Update: It would appear that this is happening because it is a 'web database' as I've been able to do all of the above in a new regular database. With this in mind let me ask a different question: Am I able to add relationships and change primary keys in a web database? If so how? More generally, what is the point of a web database?

  Read the article

• Install KVM based Windows 2008 remotely over SSH on a headless, no graphics Ubuntu 10.04 server?

  - by taazaa

  Hi, I have a Dell server at a remote data center with Ubuntu 10.04 as the host. It is a minimal install with the necessary virtulization packages. There is no X and the machine is headless. I have the win2008 DVD in the machine and want to remotely install it. I tried: virt-install --connect qemu:///system -n vmwin2k8 -r 1024 --disk path=server2k8.qcow2,size=50 --cdrom /dev/sr0 --vnc --noautoconsole --os-type windows --os-variant win2k8 The qcow2 image get created However I don't understand how to connect to see the install via VNC. This is my first time doing it so it may be trivial or may not be possible. Remotely I have a Win 7 machine with Putty and RealVNC viewer. Where is the graphic output of VNC going? Do I have to have VNC server running on the host or some other machine and then connect to it from my VNC client? Please let me know or point me to the right direction. I have been searching the web for several days to figure out how this is suppose to work. Thanks!

  Read the article

• AWS instance went down for restart, came back up and has been "Waiting for network configuration... " for 12 hours

  - by kavisiegel

  What happened was about a month ago, I created a new instance, re-configured everything, and mounted the old instances drive to the new one. I then detached the old drive from the instance, but it was still mounted, so it errored out. Now, come the outage last month, and when the instance boots back up - the drive isn't there, because in the downtime, it dismounted. It hangs because the fstab is looking for it. I get word that the server's not up today, I check the logs, re-attach the drive and restart. Now I'm getting "Waiting for network configuration..." and it doesn't seem to be doing anything. Some googling told me that I'm going to need to start from zero again, which I don't think is right. I created a new instance, which booted no problem, then I stopped it and swapped the two old drives into the new instance. Still the same error. Using the fresh AMI, it worked. I figure it's just a misconfigured Amazon file. I can attach the drive to a functioning instance on the same AMI and copy some files over, then try again - but I don't know where to even start or what files to check.

  Read the article

• Server on blacklist

  - by Cudos

  I have a Debian Wheezy server with several websites with separate domains. Some of these websites uses Wordpress and in turn uses PHP's mail function to send mail. I installed "sendmail" to be able for the server to send mail from PHP. We use Google Apps for our customers, so no need to setup a regular mail server. Now the server is blacklisted at www.spamhaus.org and get this message: This IP address is HELO'ing as "localhost.localdomain" which violates the relevant standards (specifically: RFC5321). I have tried to follow the instructions on these websites with no luck: http://www.cardiothink.com/downloads/README.spamhaus-and-blocked-email.html http://centosbeginer.wordpress.com/2011/07/12/how-to-remove-ip-in-cbl-spamhaus/ Can you please help me figure out how to configure the server? File: /etc/hosts # nameserver config # IPv4 127.0.0.1 somedomain.dk xxx.xxx.xxx.xxx server.somedomain.dk bigby # # IPv6 ::1 ip6-localhost ip6-loopback xxxx::0 ip6-localnet xxxx::0 ip6-mcastprefix xxxx::1 ip6-allnodes xxxx::2 ip6-allrouters xxxx::3 ip6-allhosts xxxx:xxx:xxx:xxxx::2 Debian-76-wheezy-64-minimal File: /etc/hostname bigby somedomain.dk is a made up domain. In reality another domain name I have on this server along with other domains. bigby is also a made up name. It is also something else in reality.

  Read the article

• Conditional formatting Excel 2007/2010: Highlight the first cell in the row that contains duplicate values?

  - by Nancy Prades

  I have a table with hundreds of columns and rows of data; each row and column have a header. For instance, column headers are ITEM, FILE1, FILE2, FILE3, etc. and row headers are AA, BB, CC, DD, and so on. Under conditional formatting, I used "Highlight Cells Rules" "Equal to", in order to highlight cells that have values equal to the value in another cell. In this case, my formula rule is: Rule: Cell Value = $A$1 Applies to: =$B$3:$G$8 When I input "X" into cell A1, Excel will highlight all of the cells that have a value equal to "X", in this case, the following cells are highlighted: B3, C5, G6, and E8. Here's my problem. The data that I am working with contains more than 100 columns and rows. I want to identify all of the ITEMS (AA, BB, CC, etc.) that contain the duplicate file "X". In order to do this I have to scroll right to left, and up and down. Here's my question. Is there a way to use conditional formatting to add an additional rule? I want to keep the current rule, but I also want the row header to be highlighted if any of the cells in that row contain a value equal to "x". In this case, I want AA, CC, DD, and FF to also be highlighted. Is this possible? I've spent days trying to figure this out - and no luck. Any help would be appreciated! :) Nancy A B C D E F G 1 X 2 ITEM FILE1 FILE2 FILE3 FILE4 FILE5 FILE 6 3 AA x t y u d w 4 BB r y a b k d 5 CC y x f u i g 6 DD t v b d f x 7 EE e w y s l n 8 FF w u n x e m

  Read the article

• Service redirection on same network

  - by Unode

  I have a network on which I run multiple servers each dedicated to a given service. Because most services run on distinct ports I'm currently looking for a way of unifying "all" services into a single "proxy" machine. The idea is to abstract which machine is being accessed but still allow direct connection if needed/requested. This "proxy" machine has only one network interface which is part of the same network as all the other service providing machines. I've looked into Routing and NAT but I've so far failed to figure out how to make it work. I tried to achieve this using shorewall but couldn't find clear examples. However I'm not entirely sure this is the best/simplest strategy. With that said, what would be the best way of achieving this result? Example case: Proxy IP - Listening port - Send requests to 192.168.0.50 80 192.168.0.1:80 " 22 192.168.0.2:2222 " 3306 192.168.0.3:3000 " 5432 192.168.0.4:5432 " 5222 192.168.0.5:5222 PS: I'm not concerned with the single-point-of-failure nature of the proxy. Thanks

  Read the article

• Mac always boots with incorrect display gamma (for years now including Lion)

  - by Alex Wayne

  I think somewhere, something got installed but I have no idea what or how to fix it :( Basically, my old MacBook Pro running 10.5 Leopard had a problem where on boot it would show everything on the screen in a very sort of crunched color space. Everything below 15% white would just be pure black, everything above 85% white would be pure white and all colors look to be a touch more saturated. It's garish. To fix it, I found that I could boot into almost any fullscreen 3D game. When the game launches, the colors would still be off, but when I then quite the game and return the desktop everything is normal again. I've noticed Blizzard games work most reliably for this (World of Warcraft or Starcraft2). This problem has followed me through the years. When I upgraded to an iMac I migrated everything over to it, and the issue now happens on the iMac too. I then got a new MacBook Pro for work and migrated my iMac over to that, and it has the problem too. I had thought that it was an OS bug, but upgrading to 10.6 Snow Leopard didn't fix it and neither did 10.7 Lion. Furthermore I can't find any reference on any forum or help site where anyone else has this problem. If anyone has any idea what processes or settings or apps I should look at to figure out why this is happening I should would appreciate it! It looks sort of irresponsible when I open my laptop in the office to work and then boot up Starcraft 2 full screen...

  Read the article

• Pc freezes then wont boot. The fans spin, but HDD activity light is off

  - by Stuart

  I'm having a problem with my PC and this isn't the first time it's happened. For a few days now, when I turned my PC on, it didn't immediately start to boot up. The monitor said "No signal" and the machine just sat there although the power light was on and the fans were running. Then, after a few minutes, it would begin to boot as if nothing was wrong. Today I started my machine and it ran ok for about 10 minutes. Then the whole thing froze up and I had to shut it down and restart by holding the power button. When it rebooted, the same thing happened again and again and now finally it wont boot up at all. This happened before about 8 months ago. I ended up taking it to the shop after getting a blue screen. They replaced the HDD and upgraded it to windows 7 and it has worked fine since then. However, they charged an arm and a leg for the work and I dont want to have to go back there again. As this is a recurring fault I figure its a mechanical problem of some sort but I'm not sure what. Any ideas? Thanks for your help.

  Read the article

• error while resolving DNS requires

  - by user2803887

  I followed this document to configure master-slave powerdns servers... http://linuxmanage.com/master-slave-powerdns-managed-by-poweradmin.html Installation completed perfectly no errors even I feel DNS is trying to resolve some queries and parameter.. but while going through intodns.com i get below error for domain names which i have created in powerdns name server installed as above guide. Error Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records. Error Multiple Nameservers ERROR: Looks like you have less than 2 nameservers. According to RFC2182 section 5 you must have at least 3 nameservers, and no more than 7. Having 2 nameservers is also ok by me. Error Missing nameservers You should already know that your NS records at your reported by your nameservers are missing, so here it is again: nameservers ns1.makeittiny.com. ns2.makeittiny.com. I am much new to powerdns so not able to figure out where problem.. i check all things but not able to make out where problem remains.

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• mysql disk io keeps increasing ... is that normal?

  - by trustfundbaby

  So I've been trying to figure out this disk IO problem I have been having with my linode VPS. Over the last day or two I've just left watch -n1 pidstat -d running in a console window and the output looks like this: Monitoring it over the last few days, I've noticed that my problem lies with the init, searchd, and mysql processes. Searchd is sphinx and all its indexes are on disk, so disk io there is inevitable (apparently). What I can't understand is why the disk reads (kB_rd/s) for mysql refuse to stabilize and just keep going up. It started out at 154 yesterday and is up to what you see in that screen shot. but disk writes (kB_wr/s) have remained pretty constant the entire time. My VPS only has 768MB RAM, my mysql db has a size of about 220MB and after running mysqltuner.pl and reading a bit about it, I've been advised to set my innodb_buffer_pool_size to 220MB but I simply cannot afford to do that ... I have it up to 150MB. My question is twofold. Why does the init process have that much disk reading to do? Why is mysql doing so much disk reading?

  Read the article

• Can't upgrade MySQL Server on new Ubuntu 12.04 install

  - by user179627

  After freshly installing Ubuntu server 12.04, I did the usual apt-get update / apt-get upgrade, which failed for mysql-server-5.5: Setting up mysql-server-5.5 (5.5.31-0ubuntu0.12.04.2) ... start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured I tried a wide variety a approaches suggested by googling, which involved various combinations of apt-get remove/purge/install -f/reinstall, etc., with no luck. I also tried downloading the package directly from launchpad.net and running dpkg -i on it (this had worked for a similar issue with a kernel upgrade), but to no avail. I'm not actually particularly interested in what's going on with mysql, per se (though I will need to figure it out at some time); at this point, my primary concern is that I am unable to apt-get install other packages! What to do?

  Read the article

• Cloned Centos 6.4 websrver for test purpose. Virtual host, .htaccess, redirecting url issue

  - by Shogoot

  I see similar questions, but not my exact challenge. What I have done so far I cloned a prod server over to a vmware to use it as a test server for new functionality I'm going to write. I'm not a sysadmin by trade, but I'm new to this company and I have to do some thing that are outside of my comfort zone (thats a good thing :) ) The prod server has 2 sites on it s1.com and s2.com. In /html/s1/, /html/s2/ there's an .htaccess file under each s*/. Looking like this: RewriteEngine ON RewriteBase / RewriteCond %{QUERY_STRING} id=([0-9]+) RewriteRule ^.* %1.htm RewriteCond %{QUERY_STRING} page=modules/checkout RewriteRule ^.* order.php RewriteCond %{QUERY_STRING} page=pages/sidekart RewriteRule ^.* pages/sidekart.htm The issue is that s1 has a lot of pages that really belongs under a third domain s3, the rule in line 4 and 5 redirects them to /html/s1/. An example of such URL is: s3.com/?page=modules/product&id=521614 I'm trying then to get those URLs (without modifying the URL) to redirect to s3's /html/s3/ server structure, which I set up making a new virtualhost s3 in test servers httpd.conf with a test3.com as servername and changing the other sites to tests1.com and tests2.com, and adding .htaccess also to this s3 root directory, and making a html/s3/ directory structure I populated with an index.html, etc. But, when I take the same URL (s3.com/?page=modules/product&id=521614) changing it to tests3.com/?page=modules/product&id=521614, I get s1's index page showing up in my browser. I've poked around about a day now and i cant figure out why this happens.

  Read the article

• File Acces\Rename Issue

  - by Moon .

  Guys, i am having serious problem with media files (only video files). When i try to rename or delete a Files or the Folders that contained media files, i get an error. "Access Denied .... Some other program might be using this file..... bla bla bla" Previously for this knida problem i had a freeware "Unlocker" that used to work. What "Unlocker" used to do was simply kill the process that is using the file. But in my case, now that is, the process using the files is "Explorer.exe" W.T.F... A strange behavior, when i copy paste the same file. The copied file, I can rename it, i can delete it, i can shit on it if i want to.... but what is wrong with the original file. Check the following list. It will give you a better idea of my situation. I am using Win XP SP 2 I have got Div Player installed (latest) The media files are from both, my hard drive, created by many of my previous window installations. And new downloaded files. So Files ownership or Privacy is not an issue. I may not be able to rename\delete those files one moment, the next moment, in the next try, i might succeed. The problem is a major F. i can't figure it out. Please F1! its getting on my nerves.

  Read the article

• mdadm: Replacing array with entirely new drives

  - by hellfur

  I have a server with three 500GB drives, with most of my data in a RAID5 configuration spanning the three of them. I just purchased and installed four 1TB drives, and the intention is to move off of the old drives and onto the new ones. I have enough SATA ports and power connectors to power all seven of my drives at once, so I've kept the old RAID running while I figure out what to do with the new drives. My question is: Should I create a whole new array on the 1TB drives, then move everything over and reconfigure linux to boot from the new md arrays? Or should I just expand the array, swapping out each of the three 500GBs with the 1TB, then adding the final drive? I've read up on the mdadm extending drive setup, and it makes sense, but I imagine I would use one of the drives as a full backup while I move things over, then add that drive back into the array once things are up and running on three of the 1TB drives, so there's some complication in going that route as well... I'm just not sure which is safer/recommended.

  Read the article

• apache/httpd responds slower under EL6.1 than EL5.6 (centos)

  - by daniel

  I've read through other threads on performance differences between RHEL6 and RHEL5, but none seem a tight match to mine. My issue manifests itself in slightly slower average response time (20ms) per request. I have about 10/10 servers of the same hardware spec with Cent6.1 and Cent5.6. The issue is consistent across the group. I am running Ruby on Rails with Passenger. Apache config is identical (checked out from the same SVN repo) Ruby and Passenger are identical builds. Application is identical and being served traffic round robin. mod_worker An interesting clue from server-status: The Cent6.1 servers have a steady 20-40 threads in the "Reading Request" state while the Cent5.6 servers have around 1. I'm graphing this so I can see it trend over time. I also have a bunch of much newer machines that are significantly faster and are running Cent6.1. They dust all the older machines in response time, but I can see they also have a steady 20-40 threads in the "Reading Request" state. This makes me believe I can get their response time down, if I can figure out what is holding up these requests. My gut is telling me that I need to tune some network setting in sysctl, but I haven't figured it out yet. Help is appreciated.

  Read the article

• Get more space for redis in unix server

  - by DevTraveler

  In our app we have only windows servers beside the cases we use redis queues. This case , we use unix server created by amazon. As you can see we do not have a lot of space available and we want to make sure redis has enough space to work without getting stuck. I am little bit new in unix and after reading some data about the unix file system i still was not fully sure how can i give the redis drive (it is in the home directory) more space. I see the mnt that has a lot of space but read it is temporary for cd-rom and network drives. Can you help me figure out how to get more space to my redis ? If it is possible i prefer not to re-install the redis server. Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.7G 880M 89% / udev 7.4G 4.0K 7.4G 1% /dev tmpfs 3.0G 152K 3.0G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.4G 0 7.4G 0% /run/shm /dev/xvdb 414G 30G 364G 8% /mnt Thanks.

  Read the article

• Nagios escalation debugging

  - by Oesor

  I'm having some issues with escalations happening properly and I'm not sure if it's because of my config or because the nagios binary is nonstandard and something may be broken. I've got little experience with nagios, and just want to make sure this is being set appropriately. Should the following config file definition allow the escalations to take over and increment the notification interval as expected? Is there somewhere else in the config files I should be looking at to figure out what's going on? I've enabled debug 32 in the config and it's simply spitting out 'Host notification will NOT be escalated.' for each notification. The configuration does pass the pre flight check with no issues, and reports that it's parsing the three host escalations in the config. # test host definition define host { host_name test alias test address 10.0.0.10 hostgroups test check_interval 0 retry_interval 1 max_check_attempts 2 flap_detection_enabled 0 icon_image windows.png icon_image_alt LOGO - Windows vrml_image windows.png statusmap_image windows.png action_url /info/host/275 check_period 24x7 contact_groups hostgroup15_servicegroup1,hostgroup15_servicegroup10,hostgroup15_servicegroup13,hostgroup15_servicegroup14,hostgroup15_servicegroup2,hostgroup15_servicegroup3,hostgroup15_servicegroup4,hostgroup15_servicegroup42,hostgroup15_servicegroup45,hostgroup15_servicegroup46,hostgroup15_servicegroup47,hostgroup15_servicegroup5,hostgroup15_servicegroup8,hostgroup15_servicegroup9,ov_monitored_by_master check_command check_host_15!-H $HOSTADDRESS$ -t 3 -w 500.0,80% -c 1000.0,100% parents nagios notifications_enabled 1 notification_interval 3 notification_period 24x7 notification_options u,d,r use host-global } define hostescalation{ host_name test first_notification 3 last_notification 4 notification_interval 10 contact_groups hostgroup15_servicegroup1,hostgroup15_servicegroup10,hostgroup15_servicegroup13,hostgroup15_servicegroup14,hostgroup15_servicegroup2,hostgroup15_servicegroup3,hostgroup15_servicegroup4,hostgroup15_servicegroup42,hostgroup15_servicegroup45,hostgroup15_servicegroup46,hostgroup15_servicegroup47,hostgroup15_servicegroup5,hostgroup15_servicegroup8,hostgroup15_servicegroup9,ov_monitored_by_master } define hostescalation{ host_name test first_notification 4 last_notification 5 notification_interval 30 contact_groups hostgroup15_servicegroup1,hostgroup15_servicegroup10,hostgroup15_servicegroup13,hostgroup15_servicegroup14,hostgroup15_servicegroup2,hostgroup15_servicegroup3,hostgroup15_servicegroup4,hostgroup15_servicegroup42,hostgroup15_servicegroup45,hostgroup15_servicegroup46,hostgroup15_servicegroup47,hostgroup15_servicegroup5,hostgroup15_servicegroup8,hostgroup15_servicegroup9,ov_monitored_by_master } define hostescalation{ host_name test first_notification 5 last_notification 0 notification_interval 240 contact_groups hostgroup15_servicegroup1,hostgroup15_servicegroup10,hostgroup15_servicegroup13,hostgroup15_servicegroup14,hostgroup15_servicegroup2,hostgroup15_servicegroup3,hostgroup15_servicegroup4,hostgroup15_servicegroup42,hostgroup15_servicegroup45,hostgroup15_servicegroup46,hostgroup15_servicegroup47,hostgroup15_servicegroup5,hostgroup15_servicegroup8,hostgroup15_servicegroup9,ov_monitored_by_master }

  Read the article

• C# lost local variable window from debug (f11 step by step)

  - by Jane

  I was running my code (visual studio 2010) and I accidentally closed the window that shows the state of variables step by step. I think it was called locals but I can't find it on any of the menu option. Would appreciate any help on this, I didn't realize how handy it was until now - The following link is what my local window looks like when selecting debug/start debugging/selecting breakpoints, which I'm don't find helpful. This is what my window used to look like: http://www.google.co.nz/imgresum=1&hl=en&sa=N&biw=1600&bih=761&tbm=isch&tbnid=Sa5AmVW5BxxakM:&imgrefurl=http://www.codeproject.com/Articles/79508/Mastering-Debugging-in-Visual-Studio-2010-A-Beginn&docid=4Iskh8P-E7oVSM&imgurl=http://www.codeproject.com/KB/cs/MasteringInDebugging/debug30_small.png&w=640&h=228&ei=TjKBUKGwKcXVsgauvIGYDQ&zoom=1&iact=hc&vpx=1119&vpy=441&dur=1559&hovh=134&hovw=376&tx=219&ty=79&sig=104270260849502265426&page=1&tbnh=91&tbnw=256&start=0&ndsp=22&ved=1t:429,r:0,s:20,i:134 It's probably a mode/option within debugging I need to select but I can't figure out how to get it back to the nice and simple variable state display..

  Read the article

< Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >