Search Results

Search found 1228 results on 50 pages for 'asus'.

Page 36/50 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• I have problem with pc. Random reboots with post hyper transport sync flood error

  - by user29867

  I have problem with my pc. Random reboots with post "hyper transport sync flood" error. It happens completely random. Most times i watch movie, some times when i play a game, even when i browse internet. My spec are as follow: MB ASUS M4A78-E CPU Phenom II 940 Sapphire Radeon hd4850 Vapor-X RAM OCZ DDR2 PC2-8500 kit 2x2GB PSU CM Real Power M520W CASE CM Centurion 590 Temps of MB, CPU and 4850 are in normal range. MB is hooter, around 60-70°C under load, Radeon 60-65°C under load (playing game for couple hours). CPU dos not past 50-55°C. So i think its not a cooling problem, CM case is pretty good, and have a lots of fans. I try with this memmory: TWIN2X4096-6400C5DHX same problem.

  Read the article

• further troubleshooting on a p8z77 motherboard

  - by Journeyman Geek

  I just bought a brand now asus p8z77 motherboard with a intel 3770. Its currently not booting - the system powers up for half a second and then powers down, and the CPU error light shines. I've tried switching ram between slots, switching PSUs, updating the bios (which can be done sans processor or ram on this model). Power: The 8 pin power connector is definitely in place correctly, and I've tried swapping PSUs between a new seasonic m12, and a known good cheapie PSU Ram: Ram is in the recommended slot for single stick operation, and tried swapping between the two sticks of DDR3 I have. Processor: Its installed correctly as far as I can tell, no obvious bent pins on the motherboard. At this point I'm guessing I'll need to RMA something. Are there any 'definitive' tests I can try, short of swapping CPU and motherboard that would let me know it is the CPU? Can I actually trust the error light on the motherboard?

  Read the article

• Second Monitor "Input Not Supported"

  - by Drew

  I have two identical monitors (new Acer s211hl) with a native resolution of 1920x1080. When enabling dual monitor support in Windows 7, the primary monitor works as expected, but the second monitor says, "Input not Supported" and fails to display anything. If I change the resolution of the second monitor to 1440x900, it works as expected. Likewise, if I set it to 1920x1080 with a refresh rate of 30hz, the monitor displays video. However, neither of these are solutions, because the output looks very blurry, and the content is stretched. I am using the following hardware: Monitors: Acer s211hl Motherboard: Asus F1A75M-Pro CPU/GPU: AMD A8-3850 with integrated Radeon HD 6550D graphics I suspect that there is probably an issue with the integrated graphics or motherboard not being able to output to two 1920x1080 monitors, but I am hoping for official confirmation.

  Read the article

• Make GRUB 2 boot Windows 8 safe mode

  - by Tim

  I have a dual boot configuration: Windows 8 Consumer and Ubuntu 11.10. I tried to install the Asus drivers for my motherboard (P8Z68-V LE EFI) in windows 8, and i now get bluescreens when starting windows. Holding F8 or Shift-F8 doesn't seem to be working, so is there another way to get into Safe Mode, or uninstall the errant driver? I need to get into Safe Mode in windows to fix the issue. Things I have tried: Disabling overclock Holding F8 or Shift+F8 How can i get GRUB 2 to boot windows 8 in safe mode? Or is there another way to disable a driver that is making it impossible to boot?

  Read the article

• HDD not detected whenever first power on (detected at BIOS level)

  - by Alvin Lim

  I am using Asus P8H61-M LX Motherboard with latest version of BIOS: 4401 One SATA-3 Western Digital Black Series 1.5TB is attached to SATA port 0 A Samsung 22x DVDRW SATA drive attached to SATA Port 1. ps/2 Logitech mouse and keyboard. CPU is i3 with DDR3 8Gb RAM. no other devices are installed. My problem is that when I turn on the computer, the WD HDD is not detected. ie cannot be booted. I have to press ctrl+alt+del in order to get it detected. I'd used the WD data lifeguard software to scan the HDD, the smart status is OK, the surface scan does not show any error at all. Where did I do wrong? Any advice is greatly appreciated.

  Read the article

• NVIDIA Driver Crashing on Custom-Built Windows 7 PC

  - by srunni

  I've got a custom-built PC with these specs: Fractal Design Define R3 ASUS P8Z77-V motherboard Intel Core i7-2700k with Thermalright HR-02 Macho Cooler NVIDIA GeForce GTX 560 with Arctic Cooling Accelero Twin Turbo II Cooler Crucial M4 128 GB SSD 1 TB Hitachi HDD G.SKILL Ares Series 2x8 GB RAM (x2) SeaSonic 520W PSU Windows 7 Ultimate SP1 (x64) NVIDIA driver version 301.42 Upon building the PC, I overclocked the CPU (but never the GPU), and there were no problems for 1-2 months. Then I started getting crashes with this error when doing anything that's computationally or graphically intensive: I un-overclocked the CPU, but that hasn't fixed anything. This is what the inside of my case looks like: I'd appreciate any guidance on resolving this problem. I did get some of the thermal paste on the graphics card when installing the aftermarket cooler, but there were no issues for a month or two. Update I did a clean install and the issue persisted - looks like it's a hardware issue. I will try removing/cleaning/reseating all the parts.

  Read the article

• XDMCP is slow any ideas? (looking for alternative remote desktops)

  - by peteri

  I've been used to using RDP on Windows to remote to machines, and I've got an asus eee 701 which I want to use to do some *nix programming on. While the eee is a lovely little machine the screen and keyboard are a little small to use for lots of programming. I've tried using Xming (the free version) to remote login into the eee from my desktop using XDMCP (or even using a ssh session as a straight X11 server and no desktop on the eee) the whole thing seems seriously slow over wifi the initial desktop takes at least 5 seconds to paint (might even be 10 seconds I haven't actually timed it). So my real question is what do other folks use for remote control with a GUI for their *nix boxes? I am finding it hard to believe the performance is so bad over a wifi network (It makes the Mac IIs I used to use a college in 1988 seem fast) or is this just a problem with Xming and using say the Cygwin X11 server would be better.

  Read the article

• A good free software for freeing up RAM Memory in Windows 7(64bit)

  - by Flavius Frantz

  I am looking for a good windows 7 software to free up RAM memory on my PC... i tried some ones I found on google but they were bad stuff... with viruses, spamware etc... i want a free clean professional software, if you don't know a good one thats free, please recommend a payed version. Also other tips/software to speed up my pc(on win7- 64bit) and such utilities. Also software to measure temperature would be great... If you can make a "must have" list of such software... Thank you I am a graphic designer, usually using this stack exchange for graphic design questions, now I realised there is this superuser one... nice :) [I usually have a lot of running programs, such as Photoshop, Flash, Illustrator, InDesign, running at the same time... with only 4GB of RAM memmory.. any tips to improve my PC perfomance would be great... I have a Asus K50IP Notebook]

  Read the article

• Mac OS X Lion (10.7.3) Virtual Machine?

  - by Ben Hooper

  I have been looking into this for a while and have attempted quite a few "solutions" (hackintosh boot images, universal unlockers, etc) before I gave in and asked for help. I know this is extremely difficult to accomplish, especially with an AMD CPU, but it has been done and it can't hurt to ask. Question Does anyone know of any way to actually get Mac OS X Lion (10.7.3) to boot in VMware Workstation 8.0.2? I know that Mac OS X is heavily dependant on hardware configuration, so I will post my PC's hardware below, if it helps. As far as I know it's only reliant on the CPU, but I will post it all just in case. PC Hardware Motherboard: ASUS M4A77T CPU: AMD Phenom II x4 955 Black Edition Graphics Card: Palit Sonic Platinum nVIDIA Geforce GTX 460 Memory: G-Skill [RipjawsX F3-12800CL9D-8GBXL] 8GB PSU: Arctic Power 700(W) Hard Drive: SAMSUNG HD204UI 2TB Thanks in advance. :)

  Read the article

• Where can I find a good, tab-less privacy filter for my monitor?

  - by KeyStroke

  Hi, I have an ASUS laptop with a 14" monitor (12" by 7" to be more specific), and I've been looking for a decent privacy filter that I can use with for, yet I couldn't find any. The problem with the filters I've found is that they all use those ugly "tabs" that you have to stick on the sides of your monitor in order to slip the filter in. I'm looking for ones that are like HP privacy filter, where parts of it goes under the frame of the monitor to hold it in place. Too bad HP doesn't sell filters that fit my screen. So, any idea where I can get a good privacy filter? Your help is so much appreciated

  Read the article

• Computer freeze at night

  - by matmat07

  Every night except one this week my laptop froze over night. I tried to check the event viewer, but there's no real help there. Tonight I'll do a memtest to check the RAM. And this shouldn't be a temperature issue since I can play game without any problem (Diablo 3, League of legend) Is there any diagnosys tool I could use. Maybe something that would write time down every minute so I know the precise time when it freeze? I have win7 and 8gb of RAM I installed myself Answer to comment:Asus N71JQ Unknown time, but it seems differents if I look at the last entry in the logs I have no information to tell you, that's why I ask for tool and not the solution. I usualy go to sleep after midnight, but I have AVG free edition as antivirus

  Read the article

• Question regarding IPv6 - Solicited-Node Address with a Link local scope

  - by Pulse

  Situation: A small LAN comprising a Windows 7 Ultimate x54 PC, 2 XP Pro x86 PCs and an Asus router.The Win 7 box has IPv6 enabled. There are no other IPv6 enabled devices on the LAN. In my firewall I see numerous requests originating from the Win 7 PC, which are for the Multicast address ff02::1:ff.... which is a Solicited-Node address query and has a scope of 2 which equates to the local link. As far as I knew local link addresses are filtered by routers, hence local link. Given that situation I'm wondering why I'm seeing these queries being generated to various addresses? Any ideas? Thanks.

  Read the article

• Computer hangs on start-up, but re-start always works

  - by user10604

  I press the power switch; the fans start whirring; then precisely nothing happens. The monitor lights (I have two monitors) blink to indicate that they aren't receiving any signal - no BIOS splash screen, nothing. This scenario occurs about 80 percent of the time, the other 20 percent being normal starts. Noticing that the computer has not started properly, I press the power switch for four seconds to turn the computer off, and then I press it again to start the computer for the second time. It always starts normally the second time. Always. The power supply is a 750W from SilverStone. The motherboard is a Gigabyte P55A-UD3P. The video card is an Asus EN9800GT. There's 8 GB of RAM. I don't know what other information might be pertinent. Help!

  Read the article

• how to debug BSOD irql_not_less_or_equal error

  - by Sev

  So I'm getting the irql_not_less_or_equal BSOD. I tried looking at the event viewer for potential causes, and cannot find any. I also checked the CPU temperature in BIOS right after the error and that was fine. I've tried 2 sets of RAM chips already, both give the issues. The error doesn't happen consistently...it happens daily, but many hours can pass and it won't happen, or only 10 minutes can pass and it might happen again. By the way, just bought the parts and built the computer myself a couple of weeks ago. How to debug the cause for this? Hardware info: Asus P6X58D PREMIUM motherboard Intel core i7 930 quad core 2.8 ghz Kingston 128 GB SSD 3 Gb/sec Nvidia Geforce GTX 465 PNY Edition Corsair 12 GB DDR3 1600 Mhz Ram Windows 7 Ultimate

  Read the article

• Computer crashes and freezes a lot

  - by Gigili

  My computer crashes like it freezes sometimes but sometimes it jumps to a black screen which I can do nothing about other than restart. I tested if it has anything to do with the programs I normally run or with the ones I installed, but it's a long time I have the problem and I think it also happened in the beginning that I bought this computer. To make sure, I normally run skype and Spiral Knights and some animation softwares like Flash. The specs are: Nvidia geforce gtx 560 evga Asus p8H67-m evo motherboard 16 gb ram Intel i7 What can I do about it? What issue is more probable to cause the problem?

  Read the article

• Computer refuses to POST

  - by TheX

  Computer refuses to POST. What it will do is the fan spins up, and the lights come on on the motherboard, but other then that it just sits there and laughs in my face! Here is what I have done... I have tried 2 different video cards, both known to work, 4 different sticks of RAM in all four ram slots, 2 processors (known to work), and 2 power supplies (known to work). The only constant is the motherboard... The Motherboard is a Asus m3a3-mvp deluxe. Anyone have any other ideas? Also, I have bread boarded it to make sure there where no shorts (taken everything out of the case and tried again).

  Read the article

• DisplayPort to DVI not working on Quadro FX 580

  - by kaosvid

  I have a PNY NVIDIA Quadro FX 580 graphics card with 1x DVI and 2x DisplayPorts. The DVI port works fine with both my Viewsonic monitors but I cannot get either of the DPs to work using the supplied DP to DVI adapter; all I get is a "no signal" on either monitor when connected to either DP port. The NVIDIA Control Panel shows that the second monitor is not connected when in fact it is. How do I get the second monitor to work? System: Windows XP Professional 32-bit Asus P5Q motherboard Core 2 Duo E8500 CPU 4GB PC8500 RAM

  Read the article

• Blinking motherboard power LED

  - by Corey D

  I was just rebuilding an old desktop PC to be used as a HTPC and the LED on the motherboard that indicates when there is power is blinking fairly rapidly. The only way I can get the machine to boot is to press the power button immediately after plugging it in, and even then I cannot make it into the BIOS. The power supply has more than enough juice to power all of the components, and is from a reputable manufacturer. The motherboard is an Asus and is about 4.5 years old. Is my power supply hosed? Or is it my motherboard?

  Read the article

• How To Adjust Properly Brightness And Contrast On Monitor

  - by Johannes

  This days, it seems that I either go worse with my eyes or some settings with contrast and brightness have been changed. However, I have been searching now for some tutorial on how to adjust contrast and brightness, and I have found already some, on how to use Microsoft Win7 Calibrate Display Color program, but some people don't recommend it.. My monitor control menu shows settings (which are by default) that contrast is set to 80, contrast to 90 and sharpnes to 45, for which I belive are pretty dam high. I'm usually every day in front of my PC about 6-10h. The biggest problem is, when the night comes, and I have to read some word document, after a 10-15m of reading, eyes starts hurting. I'm using ASUS VW198 and Nvidia 9800 GT graphic card. So please suggest me, what should I decrease, contrast or brightness or both?

  Read the article

• Windows 8 FN key doesn't work for brightness

  - by Airat Shigapov

  I have an Asus laptop with Windows 8 and fn+f5/fn+f6 keys (for brightness) doesn't work. In fact, they work, but they can increase/decrease the brightness only 1 time. I mean - after pressing fn+f5 once, nothing happens if I try to press fn+f5 again, before I press fn+f6. This only happens after logging in. At the login screen and during Windows boot I can adjust the brightness as I want, but after login I can't. I installed the latest ATK driver and NVIDIA graphics driver for Windows 8, and I think that my problem is related to conflict with drivers. I tried to reinstall/delete some drivers, but it didn't help. How can I detect where is the problem? Thanks.

  Read the article

• Graphics drivers could not find compatible graphics hardware

  - by selak

  I have a desktop with Asus P5KPS/EPU motherboard and Nvidia GF 9600 GT Graphic Adapter. I just set up new windows 7. My problem is that I cannot find a good dirver for my Graphic Adapter. I've downloaded driver from Nvidia.com which say support my GF 9600 GT, but when I installed it, it said This graphics drivers could not find compatible graphics hardware. I go into safe mode, uninstall Standard Graphics Adapter that auto installed then install my Nvidia driver, still not work. Anyone can show me how to solve this problem?

  Read the article

• Can a processor upgrade cause BSOD?

  - by Daniel

  I Had the following hardware setup: Phenom II X4 945 Asus M4A97 4GB DDR2 OCZ Radeon HD5850 OCZ Agility 2 120 GB Windows 7 x64 Pro Fully updated (latest drivers and windows update patches) Then I bought an used Phenom II X6 1090T and installed it without formatting. Since that my computer started BSODing almost every time I'm playing any game and with different error messages, like: page fault in non-paged area bad pool header the video memory manager found a problem error in dxgmm1.sys(or something like that) And when it doesn't BSOD the game simply crashes. I have tried: Updating BIOS Reseting BIOS to defaults Reinstalling Video Drivers Installing the latest DirectX All that's left is to do a full format and I don't want to do that since it's going to be a lot of work to fine tune windows to my preferences again. So is my "new" processor defective or do I really need to format the computer? Update: I use a (properly installed) custom cooler from Coolermaster and both the BIOS and the Open Hardware Monitor(Application) attest the CPU is not overheating, so I guess the CPU its defective and since I bought it from a guy over the Internet I'm probably screwed

  Read the article

• Can't unlock locked screen, in Ubuntu 12

  - by Camille Goudeseune

  After locking the screen (with a keystroke bound to xlock -nice 8 -mode blank), I can unlock the screen as expected, but only within a few minutes. After being locked overnight, when I hit a key (even Ctrl+Alt combos), the screen stays black with just a brief white flash across the middle of both monitors. The workaround is to ssh in from another host and restart X. Some months ago, this happened every few weeks. By now it happens almost every morning. How do I even start to diagnose this? What might I look for in log files? (The intermittency is particularly troubling.) Failing that, is there an alternative to xlock aka xlockmore? Hardware: 3-year-old HP minitower, GEForce 9800 GT, two Asus LCD monitors. Software: Ubuntu 12.04.2 LTS. Window manager awesome-wm. NVidia driver 304.88. XLock version xlockmore-5.31.

  Read the article

• Games + Closed Lid = Hibernation

  - by Isaac Rabinovitch

  I have an ASUS N53S that I mainly bought for its RAM capacity. (I run a lot of VMs.) But as a bonus, it came with a fancy ATI video card. So I decided to install GTA 4 and plug it into a big monitor and settle down for some casual mayhem. But after about 5 minutes, it goes into hibernation! What gives? Since I was using an external monitor and didn't need the keyboard (using an XBox controller) I closed the lid on the laptop. Gaming is compute-intensive, so my GPU and CPU were both working hard and generating heat. Closing the lid interfered with cooling. Since I have the laptop configured to hibernate when I press the power button, the heat-triggered shutdown caused hibernation.

  Read the article

• How can I pin point a USB file transfer bottleneck in Unix?

  - by HankHendrix

  I'm experiencing very slow data transfer speeds over USB 2.0 on my nix box and was wondering how I can pin-point the cause of the problem. I've looked into iotop and top but the cpu and mem figures look normal (compared to guides I have checked). The box which is affected is Ubuntu 12.04 32bit Server running on an Asus EEE 701 2G model and I am transferring from the OS over USB 2.0 to an external HDD (which transfers at 30MB/s+ on Windows 7 on other machine). I get rsync write speeds of 1MB/s from OS to USB HDD which seems ridiculously slow. These speeds are consistent with other USB HDDs and sticks.

  Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >