Search Results

Search found 26146 results on 1046 pages for 'white box testing'.

Page 360/1046 | < Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >

  • Bash script to run a clamscan on Ubuntu- how to use return values properly?

    - by Marius
    I'm trying to put together a simple script that will scan my home directory with clamscan and give me a warning if any viruses were found. What I have so far is: #! /usr/bin/env bash clamscan -l ~/.ClamScan/$(date +"%a%b%d") -ir /home RETVAL=$? [ $RETVAL -eq 0 ] && notify-send 'clamscan finished. No viruses found' [ $RETVAL -eq 1 ] && notify-send 'clamscan found a virus' && touch ~/Desktop/VirusFound [ $RETVAL -eq 2 ] && notify-send 'clamscan encountered errors. Check the logs' && touch ~/Desktop/ClamscanError find ~/.ClamScan/* -mtime +7 -exec rm {} \; However, I'm unsure about a couple of things: I'm always wary of using rm- as far as I can tell, the find command I've got should be deleting any log files that are more than a week old. I'm also not entirely sure how the return value testing works- I've got a manual that briefly covers bash, which says that the meaning of $? is "match one character", and I'm not entirely sure how that grabs the return value. Should I be using -eq or = for testing the return value? From what I can tell -eq tests strings and = tests numerals, but I'm not sure what the type of the return value is.

    Read the article

  • Using IIS7 as a reverse proxy

    - by Jon
    My question is pretty much identical to the question listed but they did not get an answer as they ended up using Linux as the reverse proxy. http://serverfault.com/questions/55309/using-iis7-as-a-reverse-proxy I need to have IIS the main site and linux (Apache) being the proxied site(s). so I have site1.com (IIS7) site2.com (Linux Apache) they have subdomains of sub1.site1.com sub2.site1.com sub3.site2.com I want all traffic to go to site1.com and to say anything that is site2.com should be proxied to linux box on internal network, (believe ARR can do this but not sure how). I can not have it running as Apache doing the proxying as I need IIS exposed directly. any and all advice would be great. EDIT I think this might help me: <rule name="Canonical Host Name" stopProcessing="true"> <match url="(.*)" /> <conditions> <add input="{HTTP_HOST}" negate="true" pattern="^cto\.com$" /> <add input="{HTTP_HOST}" negate="true" pattern="^antoniochagoury\.com$" /> <add input="{HTTP_HOST}" negate="true" pattern="www.antoniochagoury\.com$" /> </conditions> <action type="Redirect" url="http://www.cto20.com/{R:1}" redirectType="Permanent" /> </rule> from: http://www.cto20.com/post/Tips-Tricks-3-URL-Rewriting-Rules-Everyone-Should-Use.aspx I will have a look at this when I have access to the IIS7 box. Thanks

    Read the article

  • Routing a single request through multiple nginx backend apps

    - by Jonathan Oliver
    I wanted to get an idea if anything like the following scenario was possible: Nginx handles a request and routes it to some kind of authentication application where cookies and/or other kinds of security identifiers are interpreted and verified. The app perhaps makes a few additions to the request (appending authenticated headers). Failing authentication returns an HTTP 401. Nginx then takes the request and routes it through an authorization application which determines, based upon identity and the HTTP verb (put, delete, get, etc.) and URL in question, whether the actor/agent/user has permission to performed the intended action. Perhaps the authorization application modifies the request somewhat by appending another header, for example. Failing authorization returns 403. (Wash, rinse, repeat the proxy pattern for any number of services that want to participate in the request in some fashion.) Finally, Nginx routes the request into the actual application code where the request is inspected and the requested operations are executed according to the URL in question and where the identity of the user can be captured and understood by the application by looking at the altered HTTP request. Ideally, Nginx could do this natively or with a plugin. Any ideas? The alternative that I've considered is having Nginx hand off the initial request to the authentication application and then have this application proxy the request back through to Nginx (whether on the same box or another box). I know there are a number of applications frameworks (Django, RoR, etc.) that can do a lot of this stuff "in process", but I was trying to make things a little more generic and self contained where different applications could "hook" the HTTP pipeline of Nginx and then participate in, short circuit, and even modify the request accordingly. If Nginx can't do this, is anyone aware of other web servers that will perform in the manner described above?

    Read the article

  • moving plone or recovering data

    - by Atilla Filiz
    I had a simple plone site running on my Ubuntu 8.10 box, setup by following instructions on https://help.ubuntu.com/community/forum/server/Plone Now the computer got an Ubuntu 9.04 install from scratch, and I want to get the site up and running. As far as I understand several python libraries from 9,04 are not compatible with plone. I tried installing plon3-site from ubuntu repos, and I got this: $bin/instance start Traceback (most recent call last): File "bin/instance", line 103, in ? import plone.recipe.zope2instance.ctl File "/media/Robocup2009/robocup2009/eggs/plone.recipe.zope2instance-2.7-py2.4.egg/plone/recipe/zope2instance/__init__.py", line 16, in ? import zc.buildout File "/media/Robocup2009/robocup2009/eggs/zc.recipe.egg-1.1.0-py2.4.egg/zc/__init__.py", line 1, in ? __import__('pkg_resources').declare_namespace(__name__) ImportError: No module named pkg_resources I have python-pkg-resources installed. I actually don't care about plone, I just found it easy to use. My site is just photo and video archive of several users, with low traffic but several gigabytes of data. What would you suggest? Is it easier to get plone working on my box and start my instance(how?), or recover the content from the instance folder(how?) and setup another content management system(which?)

    Read the article

  • Why is this APC installation failing so badly?

    - by Matt
    I have multiple instances of APC running on my server with similar configurations (albeit with different cache sizes. However, one of the instances is performing extremely poorly, and I have no idea why (100% cache fragmentation, high miss rate). The runtime settings I'm using are as follows (pretty much out of the box): apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 1M apc.mmap_file_mask apc.num_files_hint 1000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.shm_segments 1 apc.shm_size 10M apc.slam_defense 1 apc.stat 1 apc.stat_ctime 0 apc.ttl 0 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock 1 APC is version 3.1.6, PHP is 5.3.3-1ubuntu9.5. I've tried restarting Apache multiple times, so this isn't a freak instance. The instance with problems is simply running Wordpress with a few plugins installed. All other instances (~4) on the server are running perfectly fine with almost 100% hit rates and 0% fragmentation; for example this instance is holding a website built using the Symfony framework. Any help would be much appreciated; I haven't had much experience with APC and was hoping for it to be an out-of-the-box speed boost ;).

    Read the article

  • Multiple IPs on firewall, are these virtual interfaces or what?

    - by Jakobud
    We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

    Read the article

  • Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

    - by varesa
    I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

    Read the article

  • What is the difference between Startup programs in windows and the same programs being started manually

    - by sup
    I am no Windows guy, but I am trying to get a seamless integration of Windows program through Virtual Box Windows guest onto my Ubuntu machine. I more or less followed this tutorial: https://nowhere.dk/articles/running-windows-applications-natively-with-seamlessrdp Basically I start up Windows in Virtual Box and then I try to launch an application (on Ubuntu host) like this: rdesktop -A -s "c:\Program Files\ThinLinc\WTSTools\seamlessrdpshell.exe notepad.exe" 192.168.123.103:3389 -u user -p password That just gives me full Windows desktop that I do not want. However, when I run (on the Windows guest) "c:\Program Files\ThinLinc\WTSTools\seamlessrdpshell.exe" "notepad" The command above works and I get just the window I want. Now, so I thought I would put this command into startup folder of the Windows machine and everything would be fine. But it says "Unable to set up the virtual channel". (by googling, I nailed it to this file: https://sourceforge.net/p/rdesktop/code/1686/tree/seamlessrdp/trunk/ServerExe/vchannel.c - the warning is triggered (by main.c in the same directory) when function vchannel_open() returns something that C interprets as yes for if condition). I have no idea why it works when I launch this command manually via a bat file and not when I put it to startup programs. Any ideas?

    Read the article

  • Internal and External DNS from Different Servers, Same Zone

    - by Shane
    Hello All, I am either having trouble understanding how DNS works, or I am having trouble configuring my DNS correctly (either one isn't good). I am currently working with a domain, I'll call it webdomain.com, and I need to allow all of our internal users to get out to dotster to get our public DNS entries just like the rest of the world. Then, on top of that, I want to be able to supply just a few override DNS entries for testing servers and equipment that is not available publically. As an example: public.webdomain.com - should get this from dotster outside.webdomain.com - should get this from dotster as well testing.webdomain.com - should get this from my internal dns controller The problem that I seem to be running into at every turn is that if I have an internal DNS controller that contains a zone for webdomain.com then I can get my specified internal entries but never get anything from the public DNS server. This holds true regardless of the type of DNS server I use also--I have tried both a Linux Bind9 and a Windows 2008 Domain Controller. I guess my big question is: am I being unreasonable to think that a system should be able to check my specified internal DNS and in the case where a requested entry doesn't exist it should fail over to the specified public dns server -OR- is this just not the way DNS works and I am lost in the sauce? It seems like it should be as simple as telling my internal DNS server to forward any requests that it can't fulfill to dotster, but that doesn't seem to work. Could this be a firewall issue? Thanks in advance

    Read the article

  • Disabled FRS replication on a DFS link, but the targets still list the replica set in their FRS conf

    - by Graeme Donaldson
    It's been a while since I've had to deal with the wonders of FRS, so I'm doing some testing to refresh my memory. This is what I've done so far. I am stuck with FRS rather than DFS-R for the moment since not all of my link targets are running R2. Created a domain-based DFS root, hosted on 4 servers. Created a DFS link under the root, targeted at 2 servers. The shares on both servers were empty. Dropped about 500MB of data into the target folder on one server and waited for replication to complete. Added/removed/modified files on both targets and confirmed that changes are replicated within a few seconds. Deleted the contents of the target folder on 1 server and waited for the other server to replicate the deletion. All of this worked perfectly, so now I want to remove my DFS link since I only created it for testing purposes. This is where it gets weird. I'm pretty sure that in the past I've disabled replication on the DFS link and after a short amount of time each target would log an info event in the FRS event log, something along the lines of "this server is no longer a member of replica set X". I have waited about 3 hours and I haven't seen this happen. ntfrsutl ds tells me that the server is not a member of any set, which is expected because when I disable replication on the link, the AD attributes on the computer object are removed. The weird part is... ntfrsutl sets still shows me the replica set, with all the properties, etc. So it seems like the FRS-related attributes of the target server's AD object are gone, but the FRS service for some reason hasn't removed the replica set. Can anyone see what I have done wrong?

    Read the article

  • High latency issue for web service call from amazon aws ec2 to local server

    - by SibzTer
    We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

    Read the article

  • LAMP server VM issues

    - by nullArray
    After getting a recommendation to salvage a wiki by installing a LAMP server, I went on the prowl for a good virtualized one. I used the VMware Player version. Since the windows box has Bonjour, I can, for example, go to http://lamp.local. and it works see the web client. The problem is, I can't ssh to a directory to scp the files I need, mount a usb thumbdrive (usbfs is unsupported) nor get samba working. I can't even update the ubuntu installation, it fails. I've tried bridged, nat and host-only networking settings in VMware Player. Bridged gives me an undefined IP, while the other two each have different IPs. All three settings allow me to access the web config, but none of them give me samba access. Windows usually freezes, then reports that it cannot connect. I'd rather not wipe a box to do a dedicated install, is there I way I can get this VM working, or are there better LAMP VMs out there? This one came already working and set up with VMware Player, so I thought it would be perfect... Thanks,

    Read the article

  • Debugging Samba/CUPS printer sharing with Windows

    - by mrdrbob
    I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

    Read the article

  • Is it possible to install ffmpeg and x264 on a Synology Diskstation 209?

    - by Kieran Benton
    Hi, Complete linux novice here! :) I'm trying to get my brilliant DS209 NAS box to do some transcoding for me of a few AVI videos to a format suitable for my Apply iTouch - yes I could do it with another machine and Handbrake but it would be really useful to offload some of this to the NAS to do overnight. I've managed to install ipkg onto my DS209 NAS box and have played around with installing some packages (binutils, mono, bash etc). I've even managed to install ffmpeg from ipkg and put together the correct command line profile to do the encoding as a .sh file: time ffmpeg -y -i $1 -f mp4 -title $2 -vcodec libx264 -level 21 -s 426×320 -b 512k -bt 512k -bufsize 4M -maxrate 4M -g 250 -coder 0 -threads 0 -acodec libfaac -ac 2 -ab 64k $3 However running this I get a missing dependency on libx264. I've tried building this from the latest source in git, but I get errors during the make process that I just don't understand (way out of my depth). encoder/set.c: In function 'x264_sei_version_write': encoder/set.c:491: error: 'X264_VERSION' undeclared (first use in this function) encoder/set.c:491: error: (Each undeclared identifier is reported only once encoder/set.c:491: error: for each function it appears in.) make: *** [encoder/set.o] Error 1 Can anyone else try building it or give me a pointer as to what I can do to get this going? Its been a good learning experience so far! Thanks.

    Read the article

  • Word 2013 can't compare readonly files

    - by Moshe Katz
    I am using Tortoise SVN to work with a repository that contains some documentation saved as Word documents. On my old computer, with Office 2010, I was able to compare with previous revisions. Tortoise would open Word in compare view so I could see the differences between the files. I have installed Office 2013 (final version from Technet, not the preview version) on my new laptop for testing and now I can no longer compare Word Documents. Tortoise pops up a generic error that it was unable to compare the two files. Tortoise uses a JScript file to interface with Word, so I ran that file through a debugger and found that the actual error is: The Compare method or property is not available because this command is not available for reading. Some Googling followed by some testing revealed that the error is caused by the first file opened (in this case, the previous version) being opened as Read-Only. If I change the JScript code to open in normal mode, and I find the file on the system and un-check the "Read Only" property (if necessary), then the comparison opens as expected. I was unable to find any documentation about this change to Word on any Microsoft site. Does anyone know why this has been changed, and if it is intentional and not a bug, what the benefit is of requiring the file to be writable in order to compare it with another? Note: This is tagged word-2013-preview but it is actually for the release version of Word that is available on MSDN and Technet. I do not have enough rep. on this site to create new tags (yet).

    Read the article

  • Extend RAID 1 (HP SmartArray P410i) running Linux

    - by Oliver
    I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

    Read the article

  • Remote Desktop Network Level Authentication Not Supported

    - by Iszi
    I'm running Windows XP Professional SP3 x86, trying to connect to a system with Windows 7 Ultimate SP1 x64. Recently, I updated the Remote Desktop Connection software on the XP system in hopes of using Network Level Authentication (NLA) for my connections to the Windows 7 box. After the update, I connected to the Windows 7 box over RDP and enabled NLA believing that the updated client should support it. After disconnecting and attempting to reconnect, I'm presented with the following error: The remote computer requires Network Level Authentication, which your computer does not support. For assistance, contact your system administrator or technical support. So, I checked the About page in Remote Desktop Connection to make sure the update had applied. This is what I see. Remote Desktop Connection Shell Version 6.1.7600 Control Version 6.1.7600 © 2007 Microsoft Corporation. All rights reserved. Network Level Authentication not supported. Remote Desktop Protocol 7.0 supported. I thought NLA was supposed to be a part of RDP 7.0 clients. Is there a component I'm missing somewhere?

    Read the article

  • Getting 502 instead of 503 when all backend servers are down running HAProxy behind Apache

    - by scarba05
    I'm testing running HAProxy as a dedicated load balancer behind Apache 2.2, replacing our current configuration where we use Apache's load balancer. In our current, Apache only, set-up if all the backend (origin) servers are down Apache will serve a 503 service unavailable message. With HAProxy I get a 502 bad gateway response. I'm using a simple reverse proxy rewrite rule in Apache RewriteRule ^/(.*) http://127.0.0.1:8000/$1 [last,proxy] In HAProxy I have the following (running in default tcp mode) defaults log global option tcp-smart-accept timeout connect 7s timeout client 60s timeout queue 120s timeout server 60s listen my_server 127.0.0.1:8000 balance leastconn server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 Testing connecting directly to the load balancer when the backend servers are down: [root@dev ~]# wget http://127.0.0.1:8000/ test.html --2012-05-28 11:45:28-- http://127.0.0.1:8000/ Connecting to 127.0.0.1:8000... connected. HTTP request sent, awaiting response... No data received. So presumably this is down to the fact that HAProxy accepts the connection and then closes it.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • OpenVPN: ifup tap0 drops all connections

    - by raspi
    I'm trying to create star shaped "virtual" LAN with OpenVPN which is not connected to physical network. ie. tap0 packets should not go to eth0. Packet should only go through OpenVPN to connected clients. This setup works with my OpenVPN testing machine which runs Virtual Box but not on my actual server which is running on top of Xen. Both servers are running Ubuntu Intrepid. /etc/network/interfaces: iface tap0 inet manual address 10.10.10.1 netmask 255.255.255.0 gateway 10.10.10.1 /etc/openvpn/server.conf mode server tls-server port 1194 proto udp dev tap client-to-client ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/servername.crt key /etc/openvpn/easy-rsa/keys/servername.key dh /etc/openvpn/easy-rsa/keys/dh384.pem ifconfig-pool-persist ipp.txt server-bridge 10.10.10.1 255.255.255.0 10.10.10.128 10.10.10.250 push .route 10.10.10.1 255.255.255.0 keepalive 5 60 comp-lzo persist-key persist-tun status /var/log/openvpn-status.log log-append /var/log/openvpn.log verb 3 user nobody group nogroup ifup tap0 on Virtual Box: everything ok, SSH keeps running. But on Xen SSH connection drops and I have to reboot whole machine. What I'm missing?

    Read the article

  • How to get gigabit network speeds on Windows XP?

    - by JB
    We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

    Read the article

  • Trouble with IIS SMTP relaying to Gmail

    - by saille
    I appreciate that similar questions have been asked about how to setup SMTP relaying with IIS's virtual SMTP server. However I'm still completely stumped on this problem. Here's the setup: IIS 6.0 SMTP server running on Win2k3 box with a NAT'ed IP. Company uses Gmail for all email services. An app on the box needs to send email, so normally we'd just set the app up to talk to smtp.gmail.com directly, but this app doesn't support TLS. Easy, we just setup a local SMTP relay right? So I thought. What we have done so far: Setup IIS SMTP server to relay to smtp.gmail.com, as per these excellent instructions: http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ The local SMTP relay allows anonymous access. Both the local IP and the loopback IP have been explicitly allowed in the Connection and Relay dialogs. Tried sending email from 2 different apps via the local SMTP server, but failed (the emails end up in the Queue folder, but never get sent). The IIS logs show the conversation with the local app, but zero conversation happening with smtp.gmail.com. The port used by gmail is open outbound, and indeed the apps we have that support TLS can send email directly via smtp.gmail.com, so there is no problem with the network. At this point I changed the smtp settings in IIS SMTP server to use a different external SMTP server and hey-presto, the local apps can send email via local IIS SMTP relay. So smtp.gmail.com fails to work with our IIS SMTP relay, but another 3rd party SMTP service works fine. We need to use smtp.gmail.com, so how to troubleshoot this one?

    Read the article

  • vmware - ACE, Workstation - how to manage remoe clients??

    - by tom smith
    Hi. Exploring Vmware products/services and have a few questions. As I understand VM, you can use VMWare Workstation to create a VM of a target machine/box/OS. Let's call this VM, "foo". If I have 100 client PCs in my dept, and I want to install the VM (foo) on each client, and also manage the remote VM instances of (foo). How can I accompish this? Let's assume that the client machines are running Windows7, and have the vmplayer app installed on the box. I'm looking to do the following kinds of actions regarding the remote client machines: -Update the foo VM/image with new updated copies -Make sure that every VM "foo" has the same user, but a unique passwd -Monitor the traffic/status of each client VM "foo" oin each client -Start/Stop each client VN "foo" from the master console -Etc... Can this be accomplished? How would I do it, what services/products would I need? I've tried toalking to a few of the pre-sales guys in VMWare, and got nowhere, other than telling me to email my questions!! Looking at google shed more insight, but I still have questions. So, if you have detailed VMWare understanding, pointers to consultants, or resellers who can help, all pointers are greatly appreciated. Thanks -tom

    Read the article

  • Webservice randomly dropping connections - possibly due to firewall nonevent data?

    - by adam
    I have a hosted webapp which requests data from a REST webservice in our office. Each page calls one (or several) webservices, which go from our host, via our firewall (a Watchguard Firebox) to a server in our office. All of a sudden, the app has dramatically slowed. We have determined that the webservice is timing out at random when called externally (it's fine when called within the office network). I'm pretty certain it's our connection which is dropping the webservice call, so I've written a quick php/curl script which calls the webservice over many iterations and shows the various timings. Below is an example output, showing both a failed and a successful call (with a 5 second timeout): http_code namelookup_time connect_time pretransfer_time starttransfer_time total_time 1 0 0.000096 0.0342 0.0000 0.0000 0.0342 2 200 0.000052 0.0332 0.1327 0.1751 0.1752 As per iteration #1 above, failed requests seem to be failing between connect and pretransfer. I'm not sure if this shows that the connection is successfully past the firewall, or could the firewall still cause an issue? Our firewall is showing a series of nondata event log messages for the relevant access rule. Our IT team tells me these are routine, although I can find no mention of these in Google. I'm not sure if this fits in between connect and pretransfer. Having elinated the webservice server (by testing internally) and the live webapp (by testing different code on different external servers, I am left suspecting the connection to the office. Could the firebox nondata events be causing a problem between connect and pretransfer?

    Read the article

  • NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

    - by Corey Kennedy
    What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help!

    Read the article

< Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >