Search Results

Search found 10789 results on 432 pages for 'cpu upgrade'.

Page 366/432 | < Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >

  • I think my laptop just died

    - by Joel Coehoorn
    I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

    Read the article

  • Ubuntu 12.04 Very slow especially with Android Studio

    - by Nada
    I have an old laptop with the following specification: Memory: 485 MiB, Processor: Genuine intel CPU T2300 @ 1.66 GHz ×2, OS Type: 32 bit, Disk: 78.1 GB, I installed on it Ubuntu 12.04 LTS and I noticed that the overall system is very slow in responding. I tried to search about that in the internet and I found some articles talking about how to make Ubuntu 12.04 LTS run fast I applied all what they said including download LXDE desktop environment and then nothing different in the system response time. Then I need to develop some android applications so, I download Android Studio (Beta) 0.8.6. The problem became worse than before whenever I tried to open the Android Studio the screen is frozen for some minutes then it took time to download the projects and initialize the work space also, when I tried to move the cursor he is move very slowly. When I tried to run my first application on the AVD it took three hours and still not run yet. I delete the Android Studio and install it again several times, I was trying to solve the problem but still nothing change. Please if you have any suggestions that may help me make my laptop and Android Studio work faster I will appreciate it for you. Thank you in advance.

    Read the article

  • Recommended drive encryption solution

    - by Chris Driver
    Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

    Read the article

  • Servers/Websites Keep Going Down

    - by Tyler Johnson
    Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

    Read the article

  • FreeBSD: problem with Postfix after updating LDAP

    - by Olexandr
    At the server I installed openldap-server, at this computer open-ldap client has already been installed. Version of openldap-client (2.4.16) was older then new openldap-server (2.4.21) and the version of client has updated too. OpenLDAP-client works with postfix on this server and after all updates postfix cann't start again. The error when postfix stop|start is: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix" At the category with libraries is libldap-2.4.so.7, but libldap-2.4.so.6 is removed from the server. When I want to deinstall curently version of openldap-client, system write ===> Deinstalling for net/openldap24-client O.K., but when I start "make install" system write: ===> Installing for openldap-sasl-client-2.4.23 ===> openldap-sasl-client-2.4.23 depends on shared library: sasl2.2 - found ===> Generating temporary packing list ===> Checking if net/openldap24-client already installed ===> An older version of net/openldap24-client is already installed (openldap-client-2.4.21) You may wish to ``make deinstall'' and install this port again by ``make reinstall'' to upgrade it properly. If you really wish to overwrite the old port of net/openldap24-client without deleting it first, set the variable "FORCE_PKG_REGISTER" in your environment or the "make install" command line. *** Error code 1 Stop in /usr/ports/net/openldap24-client. *** Error code 1 Stop in /usr/ports/net/openldap24-client. Updating of ports doesn't help, and postfix writes error: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix"

    Read the article

  • Why is my server performance degrading to the point of stopping, periodically?

    - by Pascal Aschwanden
    So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

    Read the article

  • Computer randomly shuts itself off

    - by Decency
    I have not been able to determine a pattern for why this happens, despite my best efforts. I've attempted to run it on full power with Prime95 and this doesn't trigger a restart. Generally the restarts occur while I'm playing games, watching videos, or even just having multiple tabs open in a browser. However, I often play processor intense games for hours without any restarts occurring, and sometimes they'll happen 3-4 times in an hour during less intense activity, so I don't think that is the problem. I imagine it has something to do with overheating or power consumption so I've been monitoring CPU temperature and cleaning with compressed air, but the problem keeps happening. I don't know how to track power consumption, and assume that this is the problem. Whenever this occurs, the sound gets stuck in a short loop of whatever was playing at the time, though restarts also occur when nothing is playing. Here is a screenshot of temperatures: and under load: Here's the parts list: http://secure.newegg.com/WishList/PublicWishDetail.aspx?WishListNumber=10546754 As shown in the list, the case includes a 585W Power Supply, which I've been told should be plenty. I built the computer myself with a friend's guidance but it's very possible I did something wrong. Right now I'm looking into ensuring that I have the latest drivers for all components. Any help would be appreciated- thanks.

    Read the article

  • IIS 7 much slower than IIS 6

    - by JoeJoe
    I have a asp.net 3.5 web application running fine on Windows2003 IIS6. I published same exact application to IIS7.5 (Win2008R2) on a faster box (i5,8Gram) and it is significantly slower. 5-6 sec per page vs. 1-2 sec per page. During that time the Task Mgr CPU is always under 10%. Both attach to same database on other box. Benchmark is consistent from any other client browser or machine. I have connection pool on both, compression on both. Same network subnet. Forms authentication (no SSL yet). Can you give me steps on how to troubleshoot where the delays are being inserted or settings in IIS7 that I may have overlooked. Just using defaults. There is only 1 web site on each box. I understand the roles of an Application as defined in IIS has changed. There is no special Application defined in IIS.

    Read the article

  • ASP.Net Session Timing Out Rapidly

    - by Zac
    We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

    Read the article

  • Can't find partition tab in disk utility osX ver. 10.6.8

    - by John W
    I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

    Read the article

  • pfsense 2.0 traffic priority - set full priority for single host

    - by Waxhead
    I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

    Read the article

  • I have a perl script that is supposed to run indefinitely. It's being killed... how do I determine who or what kills it?

    - by John O
    I run the perl script in screen (I can log in and check debug output). Nothing in the logic of the script should be capable of killing it quite this dead. I'm one of only two people with access to the server, and the other guy swears that it isn't him (and we both have quite a bit of money riding on it continuing to run without a hitch). I have no reason to believe that some hacker has managed to get a shell or anything like that. I have very little reason to suspect the admins of the host operation (bandwidth/cpu-wise, this script is pretty lightweight). Screen continues to run, but at the end of the output of the perl script I see "Killed" and it has dropped back to a prompt. How do I go about testing what is whacking the damn thing? I've checked crontab, nothing in there that would kill random/non-random processes. Nothing in any of the log files gives any hint. It will run from 2 to 8 hours, it would seem (and on my mac at home, it will run well over 24 hours without a problem). The server is running Ubuntu version something or other, I can look that up if it matters.

    Read the article

  • WINDOWS: Your computer hangs. You can windows + R (run dialog) but performance is so halted taskMGR

    - by John Sullivan
    The question is, what process are available to try to recover from total system instability before pulling the plug when we can do nothing but programs or batches in the path from the run dialog (windows + r key), and performance is so dead that taskMGR / procEXP / other programs with visual guis are not usable? I am not a windows expert, but ideally someone out there has written a program that does more or less stuff like this: Immediately set (or perhaps I can set from the run prompt) its priority to extremely high, evaluate performance bottlenecks. E.g. is CPU 100%? If so identify offending program(s) or problems. Attempt / log fixes, then provide crude feedback asking the user if his performance has stabilized enough to abort, wait a few seconds, if no feedback continue, etc. etc. Eventually try to do any "system cleanup" if the program decides it cannot recover and perhaps finally provide a series of beeps to the user, or what have you, to say "OK, I give up, time to pull the plug". Ideally create a log, when able. These kinds of horrible hangs are a situation where surely trying something, anything, is better than nothing -- as long as that something is intelligent -- when the alternative is ripping out the power coord. Again, I am not a windows expert, so perhaps there is a much more elegant "hands on" approach I am not aware of.

    Read the article

  • Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

    - by Biohazard
    I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

    Read the article

  • Why is only one Excel spreadsheet crippled, but others are fine?

    - by Dallas
    I have an inherited spreadsheet that I really don't want to rebuild at the moment. It's a simple small workbook that is small (< 200 rows that don't even reach to AA) and does nothing more than calculate some totals within the same worksheets. No macros, no external data sources, nothing beyond basic formatting of dates, numbers and strings. I see importing data from CSV/text has created many many workbook connections over time, but even if I delete them all (there were hundreds) it makes no difference in performance. Even clicking to simply change focus from cell to cell takes 10+ seconds, adorned by the spinning cursor and (Not Responding) appending to the title bar and the application locking up. The program seems to "recover" every time, but efficiency of editing this file is obviously seriously handicapped. All other files seem fine in Excel, and other programs have no apparent performance issues. I see Excel is chewing up CPU but I'm not sure how to narrow down what process or service is "clashing" with Excel. I tried the same file on other computers and performance is fine. If I turn off all start-up services and run only Excel, performance is restored... until I start using other programs and then it bogs down again. At this point, I would entertain almost any idea, theory or suggestion that helps pinpoint, solve or work around the issue.

    Read the article

  • Is it possible to record a screen-video from a VNC server?

    - by nikie
    I have a computer that's running VNC server. I would like to record a video of what's going on on this computer, if possible without installing additional software on that computer. Is there a program that can connect to the VNC server port and instead of displaying the screen save it to an (e.g. AVI) video file? Background: One of our customers sometimes has problems with the software he bought from us when he's performing a complex procedure. To help him, we offered that someone (a service technician or programmer) watches what he's doing during that procedure to find out if he's doing something wrong or if there's a bug in the software. Currently, this is done live via VNC. That has a few disadvantages: The service technician has to be in the office at the time. As the customers are in different time zones, that can be in the middle of the night. If the service technician forgets something or doesn't notice something, it's lost. There's no way to see what happened again. Only a single computer can be watched by one service technician at a time. I know I could install normal screen-grab software on the computer, but we're talking about an embedded system with limited RAM, CPU, HDD space, so installing something new is not an easy decision. And VNC is already there. I could of course open a VNC client on some office PC and capture that PC's screen, but I can only record one remote computer that way. I often have to watch up to 8 screens in parallel. (And I don't think that screen-grabbing VNC would improve image quality, either.)

    Read the article

  • Apache memory allocation error message

    - by la_f0ka
    I'm trying to set up a medium sized Drupal 7 website on my miniserver but I keep getting a 500 error message. This is what I found in Apache's error log: [Wed Sep 12 15:02:04 2012] [notice] SSL FIPS mode disabled [Wed Sep 12 15:02:04 2012] [warn] No JkShmFile defined in httpd.conf. Using default /usr/local/apache/logs/jk-runtime-status [Wed Sep 12 15:02:04 2012] [notice] Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/1.0.0-fips mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 mod_jk/1.2.35 configured -- resuming normal operations [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] File does not exist: /home/brighton/public_html/favicon.ico [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] /usr/bin/php: error while loading shared libraries: libkrb5support.so.0: failed to map segment from shared object: Cannot allocate memory [Wed Sep 12 15:02:07 2012] [error] [client 89.16.136.28] Premature end of script headers: index.php I contacted support and they just told me I should just upgrade my package (right not I have a 512Mb account), but I am not sure if I'm buying it... even if I'm trying to access a file which only contains phpinfo(); I still get the 500. Any help would be much appreciated, and if there's need of any other information please let me know and I'll update the question. I compiled apache with tomcat because I intend to use Solr... not sure if this is relevant or not.

    Read the article

  • System randomly freezes yet mouse still moves, SSD out of reallocatable sectors, should I replace it?

    - by user784446
    This problem has lasted for the past 48 hours. The first time it happened, a program I was running stopped responding, so I tried to end it from task manager. The processes at first were listed fine until hovered upon. Eventually, despite the mouse still being able to move, after a few persisting clicks the mouse finally stopped moving. The screen went blank shortly thereafter. The second time it occurred, items on the screen stopped responding - hovering over the taskbar or such wouldn't elicit a response. Sound would still play however. Eventually, the mouse became unresponsive and the system restarted itself. I suspect that it may be a problem of my SSD drive. After looking through some Google search results, I downloaded HDTunePro to determine if there's a problem with the drive. Results returned a problem of reallocated sector count. An error scan also revealed 48 bad sectors. Also, an attempt to backup the contents of the most important areas of the drive returned a few explorer "Error: cannot read source from disk" errors. Should I ditch the drive and use another drive or is there anything that can be done to repair the drive? SSD: OCZ Petrol 64gb CPU: AMD Athlon II X4 640 RAM: Generic 3GB DDR2 Motherboard: Gigabyte MA74GM-S2H OS: Windows 7 Ultimate x64 Thanks!

    Read the article

  • Slow, choppy video playback with nVidia 8600GT

    - by user5351
    I have an nVidia 8600GT card (made by EVGA) on a machine with Windows Vista (AMD Athlon X2 processors) and four gigs of ram. It runs pretty good, but I have had some slow/choppy/stuterring video playback issues whenever watching flash videos on Youtube or other sites. The problem is there with both Firefox and IE flash videos, but is maybe worse with Firefox. I also tried Linux with nVidia's binary drivers and it was about the same. I downloaded EVGA precision which allows me to control stuff like the fan and clock speed. The card's temp (in both Vista and Linux) is usually at 66C when idle (not playing a game or watching anything). It goes up a little when watching a video (maybe 68-72C). Any ideas on how to fix this? UPDATE: The issues are both with full screen and embedded flash videos. I have Flash 10.0.32.18 (always make sure I use most recent for security), and the CPU is an AMD Athlon 64 X2 Dual Core Processor 4000+ at 2.11 GHZ. The current GPU driver installed is the most recent GeForce one from last July.

    Read the article

  • AA doesn't work due to monitor?

    - by MikeQ
    I have a monitor (with TV tuner - Philips 221T1SB), native resolution of 1920x1080, but there is an Overscan in Catalyst. It says from left to right '10%' and '0%', if i set it (all the way to the left) on 10%, i get screen with black borders (you know what i mean), but if i set it to 0%, i get a filled monitor. It does make sense, but why the hell is there such an option? I never had any AA issues before, but now, with this monitor, here they go. I can't find any solution, i have only one lead = overscan, or pretty much anything with the CCC settings. Yes, i almost forgot. After a bit of trying to configure the monitor with remote, i found there is a PC channel option, few other channels, and then a HDMI option. I have monitor through HDMI, but why i get black screen when i select the PC channel? That might be another problem. I tried almost everything. Please guys, give me a hand. I don't want jaggies! CPU: Intel I5-750 @4,0GHz RAM: Corsair Vengeance 8GB 1600MHz GPU: AMD Gigabyte HD 7950 Windforce @1100/1400, 1,174V Motherboard: ASUS P7P55D-E EVO

    Read the article

  • How to reduce celeryd memory consumption?

    - by Gringo Suave
    I'm using celery 2.5.1 with django on a micro ec2 instance with 613mb memory and as such have to keep memory consumption down. Currently I'm using it only for the scheduler "celery beat" as a web interface to cron, though I hope to use it for more in the future. I've noticed it is the biggest consumer of memory on my micro machine even though I have configured the number of workers to one. I don't have many other options set in settings.py: import djcelery djcelery.setup_loader() BROKER_BACKEND = 'djkombu.transport.DatabaseTransport' CELERYBEAT_SCHEDULER = 'djcelery.schedulers.DatabaseScheduler' CELERY_RESULT_BACKEND = 'database' BROKER_POOL_LIMIT = 2 CELERYD_CONCURRENCY = 1 CELERY_DISABLE_RATE_LIMITS = True CELERYD_MAX_TASKS_PER_CHILD = 20 CELERYD_SOFT_TASK_TIME_LIMIT = 5 * 60 CELERYD_TASK_TIME_LIMIT = 6 * 60 Here's the details via top: PID USER NI CPU% VIRT SHR RES MEM% Command 1065 wuser 10 0.0 283M 4548 85m 14.3 python manage_prod.py celeryd --beat 1025 wuser 10 1.0 577M 6368 67m 11.2 python manage_prod.py celeryd --beat 1071 wuser 10 0.0 578M 2384 62m 10.6 python manage_prod.py celeryd --beat That's about 214mb of memory (and not much shared) to run a cron job occasionally. Have I done anything wrong, or can this be reduced about ten-fold somehow? ;) Update: here's my upstart config: description "Celery Daemon" start on (net-device-up and local-filesystems) stop on runlevel [016] nice 10 respawn respawn limit 5 10 chdir /home/wuser/wuser/ env CELERYD_OPTS=--concurrency=1 exec sudo -u wuser -H /usr/bin/python manage_prod.py celeryd --beat --concurrency=1 --loglevel info --logfile /var/tmp/celeryd.log Update 2: I notice there is one root process, one user child process, and two grandchildren from that. So I think it isn't a matter of duplicate startup. root 34580 1556 sudo -u wuser -H /usr/bin/python manage_prod.py celeryd wuser 577M 67548 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 578M 63784 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 271M 76260 +- python manage_prod.py celeryd --beat --concurrency=1

    Read the article

  • tomcat vs FULL J2EE Solutions

    - by jrhickey
    We are getting ready to make a major revision in our Web Application architecture which currently is running on JBoss 4.2. At first we were looking at moving from 4.2 to JBoss 6 but after some research tomcat may be a better solution for us. My first question is their anything that JBoss can do that tomcat cannot do assuming you are using the correct plugins. We do not really use EJB's in our solution and it would appear there are simple plugins for web services, JMX and other features. Tomcat appears to have much better support, faster upgrade cycles and many, many books. Since there is less to the system it also seems much easier to support from an admin point of view. What am I missing? The main features we want to enable are better clustering support and session replication / persistence. We will consider other application servers as well such as Glassfish / Geronimo. quote form a web article: Apache Tomcat is the world’s most widely used web application server, with over one million downloads per month and over 70% penetration in the enterprise datacenter. Tomcat is used to power everything from simple one server sites to large enterprise networks.

    Read the article

  • toshiba a200 laptop hangs/freezes when plugged in

    - by tapan
    The subject says it all. It is the exact same problem as described here. I had asked a similar question before here. My system specs etc, everything is here. My problem is just that I cannot afford to get it fixed right now. I just need for the laptop to be kind of usable for 2-3 more months. It worked perfectly for 3 months or so in ubuntu recovery mode. Now it hangs/freezes every hour. I spend 8 hours a day on an average on my laptop. So i just want it to last at least that long. If the laptop is not plugged in in recovery mode / regular ubuntu mode, it freezes in 5 mins and the screen becomes all weird. With my windows 7 OS, it works perfectly on battery but hangs instantly as soon as it is plugged in. Also now, a high cpu usage doesn't help anymore. Any strategy or suggestions i could employ to extend the duration for which it doesn't freeze ?

    Read the article

  • Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

    - by Warren P
    I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

    Read the article

  • Rendering a frame is producing noise from speakers in Windows and Linux

    - by Robber
    When any hardware accelerated application is rendering a frame (or many of them) a very short noise is coming from my speakers. This can be a game, a WebGL application or XBMC. When the application/game is rendering many frames per second (like most of them do) the noise is a continuous buzzing that gets higher pitched with higher framerates. This applies to Linux and Windows, so I'd assume it's a hardware problem. The current hardware in the PC is: CPU: Core2Quad Q9550 GPU: Radeon HD 5770 RAM: 2x2GB DDR2 Motherboard: Asus P5QLD PRO PSU: be quiet! Pure Power 530W Screen and speakers: Old 720p LCD TV connected via VGA and aux cable Muting the TV stops the noise, muting Windows doesn't. I tried replacing the PSU first (used a Tagan 700W PSU before) because I thought it was a power problem. It wasn't. I tried replacing the motherboard (used a ASUS P5B SE before) next because I thought it was a sound card problem. It wasn't. I tried the GPU in a different PC because I thought it was a broken graphics card. It worked perfectly fine in the other PC. I thought it might be interference, but moving the audio cable around changes absolutely nothing. I tried using an HDMI cable instead and that did work, but is not an option since my TV has only one HDMI input and I need that for my PS3.

    Read the article

< Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >