Search Results

Search found 27515 results on 1101 pages for 'embedded linux'.

Page 367/1101 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

  • ignore ipv6 router advertisements for static addresses with bonded interfaces

    - by boran
    I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

    Read the article

  • DNS Problems (NIGHTMARES!) with BIND and Virtualmin

    - by Nyxynyx
    I have a webserver (Ubuntu 12.04 with LAMP) using Virtualmin / Webmin. Because I just moved from a Cpanel system, I am having a nightmare configuring the DNS! Using intoDNS.com, the failed reports are: Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records. DNS servers responded ERROR: One or more of your nameservers did not respond: The ones that did not respond are: 123.123.123.123 213.251.188.141x Multiple Nameservers ERROR: Looks like you have less than 2 nameservers. According to RFC2182 section 5 you must have at least 3 nameservers, and no more than 7. Having 2 nameservers is also ok by me. Missing nameservers reported by your nameserver You should already know that your NS records at your nameservers are missing, so here it is again: ns1.mydomain.com. sdns2.ovh.net. SOA record No valid SOA record came back! MX Records WWW A Record ERROR: I could not get any A records for www.mydomain.com! Step-by-Step of my Attempt In my domain registrar (Namecheap), I registered ns1.mydomain.com as a nameserver, pointing to the IP address of my web server which is running bind9. The domain is setup with DNS ns1.mydomain.com and sdns2.ovh.net. sdns2.ovh.net is a secondary DNS server (SLAVE and pointing mydomain.com to the IP address of my web server) Webserver domain: mydomain.com Webserver hostname: ns4000000.ip-123-123-123.net Webserver IP: 123.123.123.123 Under Virtualmin, I edited the default Virtual server template, BIND DNS records for new domains: ns1.mydomain.com Master DNS server hostname: ns1.mydomain.com Next I created a Virtual server using that server template. This is what I've done but its still not working! Any ideas? I've been stuck for days, thank you for all your help! service bind9 status * bind9 is running lsof -i :53 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME named 6966 bind 20u IPv6 338583 0t0 TCP *:domain (LISTEN) named 6966 bind 21u IPv4 338588 0t0 TCP localhost.localdomain:domain (LISTEN) named 6966 bind 22u IPv4 338590 0t0 TCP ns4000000.ip-123-123-123.net:domain (LISTEN) named 6966 bind 512u IPv6 338582 0t0 UDP *:domain named 6966 bind 513u IPv4 338587 0t0 UDP localhost.localdomain:domain named 6966 bind 514u IPv4 338589 0t0 UDP ns4000000.ip-123-123-123.net:domain /etc/resolv.con (Not sure how 213.186.33.99 got here) nameserver 127.0.0.1 nameserver 213.186.33.99 search ovh.net host 123.123.123.123 (my web server's IP) 13.60.245.198.in-addr.arpa domain name pointer ns4000000.ip-123-123-123.net. nslookup 213.186.33.99 Server: 127.0.0.1 Address: 127.0.0.1#53 Non-authoritative answer: 99.33.186.213.in-addr.arpa name = cdns.ovh.net. Authoritative answers can be found from: 33.186.213.in-addr.arpa nameserver = ns.ovh.net. 33.186.213.in-addr.arpa nameserver = dns.ovh.net. nslookup ns1.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup ns2.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup www.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached dig mydomain.com ; <<>> DiG 9.8.1-P1 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 43540 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:09 2012 ;; MSG SIZE rcvd: 30 dig ns1.mydomain.com ; <<>> DiG 9.8.1-P1 <<>> ns1.mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 31254 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;ns1.mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:16 2012 ;; MSG SIZE rcvd: 34 /etc/bind/named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; /etc/bind/named.conf.default-zones zone "." { type hint; file "/etc/bind/db.root"; }; zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; /etc/bind/named.conf.local zone "mydomain.com" { type master; file "/var/lib/bind/mydomain.com.hosts"; allow-transfer { 127.0.0.1; localnets; }; }; /etc/bind/named.conf.options options { directory "/var/cache/bind"; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; // allow-recursion { 127.0.0.1; }; // transfer-source; }; named-checkconf -z dns_master_load: /var/lib/bind/mydomain.com.hosts:21: unexpected end of line dns_master_load: /var/lib/bind/mydomain.com.hosts:20: unexpected end of input /var/lib/bind/mydomain.com.hosts: file does not end with newline zone mydomain.com/IN: loading from master file /var/lib/bind/mydomain.com.hosts failed: unexpected end of input zone mydomain.com/IN: not loaded due to errors. _default/mydomain.com/IN: unexpected end of input zone localhost/IN: loaded serial 2 zone 127.in-addr.arpa/IN: loaded serial 1 zone 0.in-addr.arpa/IN: loaded serial 1 zone 255.in-addr.arpa/IN: loaded serial 1 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:submission ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

    Read the article

  • Can't figure out why hard drive is full [closed]

    - by Belgin Fish
    Possible Duplicate: How do I find out what is using up all the space on my / partition? No Free disk space so I have 2 hard drives in my server, one main one that is 10gb and then a separate one that is 2tb I'm storing all the files on the second one and the df -h output looks like this Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.2G 8.8G 0 100% / tmpfs 1.5G 0 1.5G 0% /lib/init/rw udev 1.5G 148K 1.5G 1% /dev tmpfs 1.5G 0 1.5G 0% /dev/shm /dev/sda4 1.8T 747G 981G 44% /home /dev/sda4 1.8T 747G 981G 44% /usr/lib/cgi-bin I just can't figure out why the first one is full when all the files are being stored in the /usr/lib/cgi-bin I'm running debian I can't seem to find any files that would take up 8.8gb that arn't on the second hard drive :S Thanks!

    Read the article

  • Accidentally replaced the partition table using GParted in UBUNTU

    - by claws
    Hello, This machine has UBUNTU & wINDOWS XP. I'm currently logged into UBUNTU. I was just checking the features of GParted and accidentally clicked Device > Create Partition Table. A default MS-DOS partition table is created. Now if I re-start the Gparted there is nothing. Its showing entire disk as UNALLOCATED space. Lucky thing is All the drives (C:, D:, E:) are currently mounted and I'm in UBUNTU. I guess its possible to re-create the partition table using current status. But I don't know how? Can any one kindly tell me how to do this. This is a lab computer. If its not recoverable. I'm completely screwed!!

    Read the article

  • OpenOffice Daemon Problem

    - by mp_gt
    Dear all, I'm using OpenOffice as a daemon. Sometimes, when the daemon is running a long time, CPU use spikes very high and then openoffice crash. At this point, the open office applicattion don't work and the documents don't be generated. How can I restart automatically the openoffice daemon when this problem happens? Is there any way to monitor the service or to program a watchdog to handle it? Thanks in advance, regards.

    Read the article

  • Manage song metadata on CentOS from command line

    - by Puddingfox
    I am making a simple Pandora.com alternative for myself and a few friends where the user can upload his/her songs and listen to them anywhere. My intent is to make a lightweight, simple player in HTML5 so all the user needs is a current Firefox or Chrome to use it. I have set it up so that all uploaded songs get converted to .ogg and added to a database but I also want some metadata (not sure if that is the correct term) for the songs to be stored in the database so the player can tell the user what song he/she is listening too. I know there are several GUI tools for managing the title/artist/album info for songs but I'm having trouble finding any good ones I can use from the command line. If the song has the information already in the file, I think I can use mplayer to retrieve the information but it would be really great if there was one that would look up the song information online. I don't mind interfacing with an API (would be pretty interesting actually). Do you guys have any suggestions?

    Read the article

  • Users database empty after Samba3 to Samba4 migration on different servers

    - by ouzmoutous
    I have to migrate a Samba 3 to a new Samba 4 server. My problem is that the database on the samba 3 server seems a bit empty. The secrets.dtb file is only 20K whereas the “pbedit -L |wc -l”command give me 16970 lines. On my Samba3 /var/lib/samba is 1,5M After I had migrate the databse (following instructions on http://dev.tranquil.it/index.php/SAMBA_-_Migration_Samba3_Samba4), “pdbedit -L” command on the new server give me only : SAMBA4$, Administrator, dns-samba4, krbtgt and nobody. So I tried to create a VM with a Samba3. I added some users, done the same things I did for the migration and now I can see the users created on the VM. It’s like users on the Samba 3 server are in a sort of cache. I already migrate the /etc/{passwd,shadow,group} files and I can see users with the “getent passwd” command. Any ideas why my users are present when I use pdbedit but the database is so empty ? The global part of my smb.conf on the Samba 3 server : [global] workgroup = INTERNET netbios name = PDC-SMB3 server string = %h server interfaces = eth0 obey pam restrictions = Yes passdb backend = smbpasswd passwd program = /usr/bin/passwd %u passwd chat = *new* %n\n *Re* %n\n *pa* username map = /etc/samba/smbusers unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%U max log size = 1000 socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 add user script = /usr/sbin/useradd -s /bin/false -m '%u' -g users delete user script = /usr/sbin/userdel -r '%u' add group script = /usr/sbin/groupadd '%g' delete group script = /usr/sbin/groupdel '%g' add user to group script = /usr/sbin/usermod -G '%g' '%u' add machine script = /usr/sbin/useradd -s /bin/false -d /dev/null '%u' -g machines logon script = logon.cmd logon home = \\$L\%U domain logons = Yes os level = 255 preferred master = Yes local master = Yes domain master = Yes dns proxy = No ldap ssl = no panic action = /usr/share/samba/panic-action %d invalid users = root admin users = admin, root, administrateur log level = 2

    Read the article

  • syntax highlighting in vim?

    - by ajsie
    on my ubuntu server vim got no syntax highlighting when i open files (configurations, scipts...). i have tried with :syntax on :syntax enable and it ways in vim that its enabled, but it doesnt work someone knows how to fix it? thanks!

    Read the article

  • How to make Shared Keys .ssh/authorized_keys and sudo work together?

    - by farinspace
    I've setup the .ssh/authorized_keys and am able to login with the new "user" using the pub/private key ... I have also added "user" to the sudoers list ... the problem I have now is when I try to execute a sudo command, something simple like: $ sudo cd /root it will prompt me for my password, which I enter, but it doesn't work (I am using the private key password I set) Also, ive disabled the users password using $ passwd -l user What am I missing? Somewhere my initial remarks are being misunderstood ... I am trying to harden my system ... the ultimate goal is to use pub/private keys to do logins versus simple password authentication. I've figured out how to set all that up via the authorized_keys file. Additionally I will ultimately prevent server logins through the root account. But before I do that I need sudo to work for a second user (the user which I will be login into the system with all the time). For this second user I want to prevent regular password logins and force only pub/private key logins, if I don't lock the user via" passwd -l user ... then if i dont use a key, i can still get into the server with a regular password. But more importantly I need to get sudo to work with a pub/private key setup with a user whos had his/her password disabled. Edit: Ok I think I've got it (the solution): 1) I've adjusted /etc/ssh/sshd_config and set PasswordAuthentication no This will prevent ssh password logins (be sure to have a working public/private key setup prior to doing this 2) I've adjusted the sudoers list visudo and added root ALL=(ALL) ALL dimas ALL=(ALL) NOPASSWD: ALL 3) root is the only user account that will have a password, I am testing with two user accounts "dimas" and "sherry" which do not have a password set (passwords are blank, passwd -d user) The above essentially prevents everyone from logging into the system with passwords (a public/private key must be setup). Additionally users in the sudoers list have admin abilities. They can also su to different accounts. So basically "dimas" can sudo su sherry, however "dimas can NOT do su sherry. Similarly any user NOT in the sudoers list can NOT do su user or sudo su user. NOTE The above works but is considered poor security. Any script that is able to access code as the "dimas" or "sherry" users will be able to execute sudo to gain root access. A bug in ssh that allows remote users to log in despite the settings, a remote code execution in something like firefox, or any other flaw that allows unwanted code to run as the user will now be able to run as root. Sudo should always require a password or you may as well log in as root instead of some other user.

    Read the article

  • Bash script to keep last x number of files and delete the rest

    - by Brady
    I have this bash script which nicely backs up my database on a cron schedule: #!/bin/sh PT_MYSQLDUMPPATH=/usr/bin PT_HOMEPATH=/home/philosop PT_TOOLPATH=$PT_HOMEPATH/philosophy-tools PT_MYSQLBACKUPPATH=$PT_TOOLPATH/mysql-backups PT_MYSQLUSER=********* PT_MYSQLPASSWORD="********" PT_MYSQLDATABASE=********* PT_BACKUPDATETIME=`date +%s` PT_BACKUPFILENAME=mysqlbackup_$PT_BACKUPDATETIME.sql.gz PT_FILESTOKEEP=14 $PT_MYSQLDUMPPATH/mysqldump -u$PT_MYSQLUSER -p$PT_MYSQLPASSWORD --opt $PT_MYSQLDATABASE | gzip -c > $PT_MYSQLBACKUPPATH/$PT_BACKUPFILENAME Problem with this is that it will keep dumping the backups in the folder and not clean up old files. This is where the variable PT_FILESTOKEEP comes in. Whatever number this is set to thats the amount of backups I want to keep. All backups are time stamped so by ordering them by name DESC will give you the latest first. Can anyone please help me with the rest of the BASH script to add the clean up of files? My knowledge of BASH is lacking and I'm unable to piece together the code to do the rest.

    Read the article

  • Filezilla connection error

    - by Kumar P
    I have RHEL 5 lan server with squid 2.6 stable proxy settings, Under this have some windows xp desktops Now i installed filezilla ftp client in windows xp, for give services to my client's websites But i can't connect ftp servers throw filezilla , I set generic proxy too. ( HTTP/1.1 USING CONNECT method ) I get error message like this, Status: Connecting to (ftp hostname) through proxy Status: Connecting to hostname:port... Status: Connection with proxy established, performing handshake... Response: Proxy reply: HTTP/1.0 403 Forbidden How can i solve this problem ?

    Read the article

  • Samba PDC share slow with LDAP backend

    - by hmart
    The scenario I have a SUSE SLES 11.1 SP1 machine as Samba master PDC with LDAP backend. In one share there are Database files for a Client-Server application. I log XP and Windows 7 machines to the local domain (example.local), the login is a little slow but works. In the client computers have an executable which opens, reads and writes the database files from the server share. The Problem When running Samba with LDAP password backend the client application runs VERY SLOW with a maximum transfer rate of 2500 MBit per second. If disable LDAP the client app speed increases 20x, with transfer rate of 50Mbit/sec and running smoothly. I'm doing test with just two users and two machines, so concurrency, or LDAP size shouldn't be the problem here. The suspect LDAP, Smb.conf [global] section configuration. The Question What can I do? I've googled a lot, but still have no answer. Slow smb.conf WITH LDAP [global] workgroup = zmartsoft.local passdb backend = ldapsam:ldap://127.0.0.1 printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes add machine script = /usr/sbin/useradd -c Machine -d /var/lib/nobody -s /bin/false %m$ domain logons = Yes domain master = Yes local master = Yes netbios name = server os level = 65 preferred master = Yes security = user wins support = Yes idmap backend = ldap:ldap://127.0.0.1 ldap admin dn = cn=Administrator,dc=zmartsoft,dc=local ldap group suffix = ou=Groups ldap idmap suffix = ou=Idmap ldap machine suffix = ou=Machines ldap passwd sync = Yes ldap ssl = Off ldap suffix = dc=zmartsoft,dc=local ldap user suffix = ou=Users

    Read the article

  • PNP4Nagios creates infinite .perfdata files

    - by Kevin Maschke
    at our company we have installed a Icinga together with PNP4Nagios. We've got a rare problem with the perfdata files PNP4Nagios creates. Each couple of weeks, we notice that our icinga server stops working correctly because it runs out of inodes. I've been looking around, and I've noticed that the problem is here: /usr/local/pnp4nagios/var/spool Each couple of weeks, this folder contains over 300k perfdata files of this type: perfdata.1336058870 I think it must be a PNP4Nagios problem, because I think that normally each "X" time, PNP4Nagios should override existing perfdata files to NOT generate new ones. Do you have any idea on what I could change or what I must do to solve this problem? Thanks in advance.

    Read the article

  • mv ,,, to * ???

    - by thedp
    I tried something on my vm ubuntu and managed to mess it up... luckily I made a snapshot not too long a go. I renamed a file to ,,, and tried to mv ,,, *. The entire dir's content of the dir disappeared. Can someone please explain to me what happened? Thank you.

    Read the article

  • Cannot connect to postgres installed on Ubuntu

    - by Assaf
    I installed the Bitnami Django stack which included PostgreSQL 8.4. When I run psql -U postgres I get the following error: psql: could not connect to server: No such file or directory Is the server running locally and accepting connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5432"? PG is definitely running and the pg_hba.conf file looks like this: # TYPE DATABASE USER CIDR-ADDRESS METHOD # "local" is for Unix domain socket connections only local all all md5 # IPv4 local connections: host all all 127.0.0.1/32 md5 # IPv6 local connections: host all all ::1/128 md5 What gives? "Proof" that pg is running: root@assaf-desktop:/home/assaf# ps axf | grep postgres 14338 ? S 0:00 /opt/djangostack-1.3-0/postgresql/bin/postgres -D /opt/djangostack-1.3-0/postgresql/data -p 5432 14347 ? Ss 0:00 \_ postgres: writer process 14348 ? Ss 0:00 \_ postgres: wal writer process 14349 ? Ss 0:00 \_ postgres: autovacuum launcher process 14350 ? Ss 0:00 \_ postgres: stats collector process 15139 pts/1 S+ 0:00 \_ grep --color=auto postgres root@assaf-desktop:/home/assaf# netstat -nltp | grep 5432 tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN 14338/postgres tcp6 0 0 ::1:5432 :::* LISTEN 14338/postgres root@assaf-desktop:/home/assaf#

    Read the article

  • Setting the Timezone with an automated script

    - by Tom
    I'm writing scripts to automate setting up new slicehost installations. In a perfect world, after I started the script, it would just run, with no attention from me. I have succeeded, with one exception. How do I set the timezone, in a permanent (survive reboot) and sane (adjust for standard and daylight savings time, so no just forcing the date) ... manner that doesn't require input from me? Currently, I'm using dpkg-reconfigure tzdata This doesn't seem to have any way to force parameters into it. It demands user input. EDIT: I'm editing here, rather than commenting, since comments don't seem to allow code blocks. Here's the actual code I ended up with, based on Rudedog's comment below. I also noticed that this doesn't update /etc/timezone. I'm not certain who uses that, but in case anybody does, I'm setting that too. TIMEZONE="America/Los_Angeles" echo $TIMEZONE > /etc/timezone cp /usr/share/zoneinfo/${TIMEZONE} /etc/localtime # This sets the time

    Read the article

  • Easily recreate a server's "state" [closed]

    - by Brandon Wamboldt
    I want the ability to setup new servers for dev/testing/prod very easily. The reasons for being able to setup a new dev VM is obvious, but for prod my concern is adding a new production server/migrating to a new server. I assume a traditional backup solution won't work as hardware may be different so the binaries/config might be different. I want to get experience with puppet anyways, so I was thinking about creating a manifest that would setup my users, install Postgres, Nginx, PHP-FPM, etc, and configure them the way I specify. Then I could install puppet on a new server, copy down my manifest and apply it locally. This would make keeping my server configs in sync easier too. Is there a better approach I'm not aware of, and does my approach have any pitfalls?

    Read the article

  • Simultaneonus NX client connections

    - by Ja Sam
    I would like to have two separate NX connections for the same username going from one dual-monitor client to NX server. The idea is to get two separate same username KDE sessions. When I try to do it the most obvious way (by starting one NX client on each separate monitor), second connection just over takes the first one. Any idea on how to do this?

    Read the article

  • How to diagnose causes of oom-killer killing processes

    - by dunxd
    I have a small virtual private server running CentOS and www/mail/db, which has recently had a couple of incidents where the web server and ssh became unresponsive. Looking at the logs, I saw that oom-killer had killed these processes, possibly due to running out of memory and swap. Can anyone give me some pointers at how to diagnose what may have caused the most recent incident? Is it likely the first process killed? Where else should I be looking?

    Read the article

  • List of common ways those could shut down server unexpectedly ?

    - by SpawnCxy
    After running a bash fork bomb which made my webserver down, I think I should be more careful even not under root.I thought it would be totally fine while I'm not under root.So I ignored the warning and ran the bash fork bomb which is :() { :|:& }; : .(Please don't run it if u don't understand this code cuz it will make you system down).And I think I need a list of common ways those could cause a sever shutting down unexpectly even not under root. Any suggestion would be appreciated. Regards `

    Read the article

  • md5sum returns a different hash value than online hash generators

    - by Ravi
    On suse10, md5sum myname gives md5 hash as 49b0939cb2db9d21b038b7f7d453cd5d The file myname contains string "ravi" while some of the online md5 hash generators for the same string seem to give a different hash http://md5-encryption.com/ http://www.miraclesalad.com/webtools/md5.php They spit out the hash for "ravi" as 63dd3e154ca6d948fc380fa576343ba6 Why is there a difference in md5sum for the same string "ravi" ?

    Read the article

  • How to fix bluescreen in windows 7 with multi-boot?

    - by Ismail Sensei
    I have HP laptop 6730S with two Operating systems : Windows 7 Ultimate 32bit Centos 6.4 64Bit The GRUB2 is not installed in MBR, use Windows' bootloader. After I choose Windows in the start, the blue-screen appears with unmountable_boot_volume problem so I tried some help from similar questions here ( use Command Prompt and enter the following command: chkdsk /R C: ). But the problem is, I can't get repair my computer it took so long and nothing happened after I waited more than 2H and when I put my Windows 7 DVD to boot it charge the files then same thing happened nothing show up so I couldn't use command prompt. But when I use Centos everything works just fine the D partition i can mounted normally but C partition it shows me error and tell me to go to windows and repair it with Chkdsk command and here is where I am stuck.

    Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >