Search Results

Search found 98288 results on 3932 pages for 'user interface'.

Page 371/3932 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

  • ignore ipv6 router advertisements for static addresses with bonded interfaces

    - by boran
    I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

    Read the article

  • windows 7 security settings for non-admins

    - by Wasi
    I was recently modifying the security settings for my drive C. I did not notice that i was logged in as a user and changed the permissions for users to "read". Later i realized that there was no admin set up on the pc (when switching user). Now with the security settings changed I can't do anything on the computer. I can only read the files that previously existed. And this applies to every drive on my computer. Now the user accounts do not have the privileges to change the permissions. How can i allow users to have full control without having admin on my pc

    Read the article

  • Unable to use Gmail in Thunderbird 3

    - by Jatin Ganhotra
    Mozilla Thunderbird v.3.1.7 I am trying to setup Gmail, but none of the settings are working. I have tried every resource: Blogs, tutorials Instructions by Google Instructions by Thunderbird Questions here But, still its not working. My settings are as follows Server Settings Server Type: IMAP Mail server Server Name: imap.gmail.com Username: [email protected] Port: 993 Default: 993 Connection Security: SSL/TLS Authentication method: Encrypted password Outgoing server (SMTP) Server Name: smtp.gmail.com Port: 587 Default: 25 Connection Security: STARTTLS Authentication method: Encrypted password Username: [email protected] IMAP is enabled in my Gmail settings. ERROR: Connection to the server [email protected] timed out. I am behind a proxy server and I have configured those settings under: Thunderbird Preferences - Advanced - Network and Disk Space - Connection Settings - Manual Proxy Configuration The proxy configuration works, as when I created a Blogs and News feeds a/c, it was working properly and fetching the feeds for me. So, Thunderbird is configured properly as per the proxy settings. Help me.

    Read the article

  • Show Windows 8 Start Menu on the primary monitor

    - by Brandon Kreisel
    I'm having the issue where the Windows 8 Start Menu shows up on the secondary monitor instead of the primary. When booting the machine the start menu appears originally on the primary screen as it should. Sometime during the course of the day the menu starts appearing on the secondary monitor instead of the primary. What should happen/initial settings: Primary Monitor - Win8 Metro Interface Second Monitor -Blank Starts happening after a few hours Primary Monitor - Blank Second Monitor -Win8 Metro Interface My Settings: Display 1: Resolution: 1920x1080 Multiple Displays: Extend these displays This is currently your main display Display 2: Resolution: 1440x900 Multiple Displays: Extend these displays []Make this my main display

    Read the article

  • Upgraded from fc10 to fc12 now I have eth0_rename, how do I get back to plain old eth0?

    - by shank
    I upgraded from Fedora 10 to Fedora 12. Unfortunately, my ethernet interface eth0 is now named eth0_rename. I'd like to get back to having it named plain old eth0. I googled a bit but the solution of removing the eth0 entry from /etc/udev/rules.d/70-persistent-net.rules seems to have no effect (I restarted the network service but didn't reboot). The interface works just fine although I could see a script or two having a problem with the format. So, it's more of an inconvenience thing than anything else. Any ideas? Thanks.

    Read the article

  • How to switch users without entering password

    - by torbengb
    I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

    Read the article

  • Manage song metadata on CentOS from command line

    - by Puddingfox
    I am making a simple Pandora.com alternative for myself and a few friends where the user can upload his/her songs and listen to them anywhere. My intent is to make a lightweight, simple player in HTML5 so all the user needs is a current Firefox or Chrome to use it. I have set it up so that all uploaded songs get converted to .ogg and added to a database but I also want some metadata (not sure if that is the correct term) for the songs to be stored in the database so the player can tell the user what song he/she is listening too. I know there are several GUI tools for managing the title/artist/album info for songs but I'm having trouble finding any good ones I can use from the command line. If the song has the information already in the file, I think I can use mplayer to retrieve the information but it would be really great if there was one that would look up the song information online. I don't mind interfacing with an API (would be pretty interesting actually). Do you guys have any suggestions?

    Read the article

  • Windows screen shots via command-line SSH session

    - by Geoff Fritz
    I've browsed the handful of "screen capture" queries here, but I was unable to find anything which addressed my specific need. I'm looking for a command-line tool that I can run via remote SSH connection (by way of the cygwin sshd daemon). There are several to choose from, but the few I've tried (ImageMagick, nircmd, and MiniCap) all result in a blank screen. I assume that this is due to the remotely logged in user not having a proper graphical console session running. The goal here is automate screen capture and retrieval of the main system console (what one would see if they were looking at the physical monitor) through the use of ssh script from a Unix host: ssh user@windowshost "screencap --output /tmp/console.jpg" scp user@windowshost:/tmp/console.jpg /some/destdir Note that these must be done on demand, so polling a remote directory that has snapshots dumped periodically will not work. Bonus points for programs that are open source and have a portable install (so I don't need to RDP/VNC into the machine to run a graphical installer).

    Read the article

  • How to edit semi-plaintext file and maintaining character structure?

    - by Raul
    I am using a software (Groupmail from Infacta) that uses exact / absolute %PATHS% for saving some settings in specific semi-plaintext file. This is a really bad idea because you can't move to USER folder, or like my case it does not work after migrating to a new computer with different language. For example: C:\Documents and Settings\USER\Local Settings\Application Data\Infacta is different than C:\Documents and Settings\USER\Configuración local\Datos de programa\Infacta Obviously, the software does not work well. I tried to solve this using Find/Replace the new PATH with Notepad++. While the Groupmail software loads well and shows settings correctly, the software fails when trying to save data on that file. I guess this is because length or number of replaced characters is different and also it corrupt the file. Please could you help me to edit this file maintaining file integrity / structure?

    Read the article

  • Video memory buswidth vs video memory Bandwidth

    - by Mixxiphoid
    My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

    Read the article

  • Windows 7 64bit making users login twice after waking up from sleep

    - by pizzim13
    I have a few Windows 7 clients exhibiting this strange behavior when my users try to login to a domain. For the issue to occur then pc must have been asleep for about an hour or more, then a user will press Alt+Crtl+Del and enter their credentials. Once they try to login the screen will go black for a couple of seconds and then go back to initial screen prompting the user to press Alt+Crtl+Del again. After entering their credentials a second time, the user can login normally and continue to do so until the pc has been asleep for over an hour. Any ideas?

    Read the article

  • IE8 Compatibility View issues

    - by 08Hawkeye
    I have the IE7 emulater tag in a jsp layout. But when I bring up the page, it defaults to the IE8 view until the user clicks the Compatibility View button. I don't want the user to have to click the button to launch compatibility mode. Is there a way to force IE7 Emulation on pageLoad? I'd even like to disable the button (or any potential to toggle between IE8 standard mode/IE7 view). Thanks! //sw Update: Now the button seems to have disappeared entirely, but still defaults to IE8 standards. Where did it go?! The toolbar context menu has it as selected, but the tools dropdown menu has it grayed out. For my purposes, it is unacceptable for the user to have to use the developer tools or even click the button to trigger emulation, but I don't know why the button disappeared anyway...

    Read the article

  • Specific IP routing for VPN

    - by Roy
    Is there a way that I can prevent an entire subnet from using internal routing. The VPN server is supposed to be a way to access the company's intranet websites for some people, while for others it is supposed to do routing to the outside only and therefore not having access to any internal websites. The VPN server has a DNS on the actual server but not all should be using this DNS. Some of the users should be directly sent out of the server to the internet. Example: 10.0.0.1 is the DNS on the server, gateway for the VPN 10.0.0.2 is a user (A) on the VPN having access to the intranet websites (subnet is 10.0.0.0/25) 10.0.0.192 is a user (B) only needing routing and no access to intranet websites (subnet is 10.0.0.192/26) All traffic of user B should be directly rerouted out of the server. I have tried several iptables but without success.

    Read the article

  • OS X Lion - Installing Oracle 10g Standard Edition

    - by Cellze
    Im trying to install oracle 10g on to OS X Lion, I have previous achieved this on snow leopard with the following http://blog.rayapps.com/2009/09/14/how-to-install-oracle-database-10g-on-mac-os-x-snow-leopard/ The issue im having is that the ulimit settings in the oracle/.bash_profile cannot be modified. I have the following in the bash_profile: export DISPLAY=:0.0 export ORACLE_BASE=$HOME umask 022 # must match `sysctl kern.maxprocperuid` ulimit -Hu 512 ulimit -Su 512 # must match `sysctl kern.maxfilesperproc` ulimit -Hn 10240 ulimit -Sn 10240 Upon applying the bash_profile settings . ~/.bash_profile i get the following error: -bash: ulimit: max user processes: cannot be modify limit: Invalid argument This then results in $ sqlplus / as sysdba not functioning correctly with a Segmentation fault: 11 The output of $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited file size (blocks, -f) unlimited max locked memory (kbytes, -l) unlimited max memory size (kbytes, -m) unlimited open files (-n) 10240 pipe size (512 bytes, -p) 1 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 512 virtual memory (kbytes, -v) unlimited If any one knows how I can apply these ulimit settings to the oracle user I have created to allow me to install sqlplus and therefore create a db, that would be great.

    Read the article

  • Training Exchange junk filter via OS X Mail.app

    - by Doug Harris
    My company uses Exchange 2007 for our mail server (via 3rd party hosted service), I use OS X Mail.app on my MacBook Pro. When viewing my junk folder in the webmail interface, there's a "Not Junk" button which will move the email out of the Junk folder. I can mimic the basic functionality in Mail.app by dragging the message from the junk folder to another folder. But... does this train the server? Specific questions: Does pressing the "Not Junk" button in the webmail interface (or Outlook) do anything more on the server side? Does Exchange used any sort of statistical spam filtering (e.g. bayesian filtering) based on this action? If the answer to #1 is yes, does moving the folder out of the junk folder in Mail.app trigger the statistical learning? If the answer to #2 is no, is there a different way to trigger the learning?

    Read the article

  • Windows 7 Computer Maintenance - Restore removed Desktop Shortcuts

    - by HaydnWVN
    I'm aware about the inbuilt nightmate 'tool' of Microsofts which is making every network administrators job a nightmare (if left turned on). In short it'll happily delete every desktop shortcut to a network resource. We have it disabled by default. My question is related to recovering these shortcuts, Windows doesn't seem to dump them into the Recycle Bin and although you can 'restore previous versions' of the Desktop folder, you are unable to do it with the user logged in... Rather a problem if you only have the 1 user account. We have a user who (although the 'Computer Maintenance' tool is turned off) had it come up in 'Action Centre' and chose to run it. I've been unable to reproduce it, but the tool has certainly run (and removed 24 shortcuts from her desktop) although it is still saying 'Windows is not checking your system for maintenance problems'. ?! Very fustrating! Any ideas if these shortcuts are backed up/moved elsewhere so i can easily find and restore them?

    Read the article

  • Mounting FTP as filesystem in debian using curlftpfs

    - by Karel Bílek
    I am trying to mount a FTP as filesystem in debian using curlftpfs. What I get after running curlftpfs -o allow_other username:[email protected] /mnt/myftp/ is just: fuse: failed to open /dev/fuse: Permission denied even when run as root. What am I doing wrong? (curlftpfs is in version curlftpfs 0.9.2 libcurl/7.21.0 fuse/2.8) edit: When I write ls -lah /dev/fuse, I see crw-rw---- 1 root fuse 10, 229 Apr 9 00:34 /dev/fuse ...but even when I add both myself and user root to group fuse, neither me (as a user) or user root can mount ftp, I still see fuse: failed to open /dev/fuse: Permission denied edit2: Even if I write this fairly insecure and crazy line: sudo chmod a+rwx /dev/fuse I still get the permission denied message. Which permissions could be denied? edit3: I forgot to mention I am on VPS with OpenVZ. I thought that there is no issue with this, but apparently, there is! I am adding the resolution as the answer.

    Read the article

  • VLC - How to restore GUI?

    - by rism
    I was mucking around with VLC setting up an http interface and somehow I've managed to turn off the default GUI - which i believe is the Qt interface. So now when i start VLC i get the process showing up in TaskManager (Im on Win 7) but no GUI. How can i re-enable GUI without an uninstall|install? I don't want to do this because I want to keep mucking around with it and if i accidentally turn off the GUI again I don't want to have to go through some uninstall|reinstall loop. I thought it would just be a config file entry somewhere but do you think i can find it? The config file that is.

    Read the article

  • OpenVPN stopped working, what could have happened?

    - by jaja
    I have Openvpn, and it worked great when I used it on PC (Windows 8), then I copied all files (Certificates and config) to an Android 4 phone to use them. Now, Openvpn works on the phone, but not the PC. Specifically, when I open Google I get: The server at www.google.com can't be found, because the DNS lookup failed, but the VPN seems to be connected. I have a simple question, could the problem be because I copied the same files? Routing table before connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 =========================================================================== Routing table after connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 **.**.***.** 255.255.255.255 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Server conf:- port 1194 proto udp dev tun ca ca.crt cert myservername.crt key myservername.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 push "redirect-gateway def1" Client conf:- client dev tun proto udp remote 89.32.148.35 1194 resolv-retry infinite nobind persist-key persist-tun mute-replay-warnings ca ca.crt cert client1.crt key client1.key verb 3 comp-lzo redirect-gateway def1 Here is the log file:- Tue Dec 18 16:34:27 2012 OpenVPN 2.2.2 Win32-MSVC++ [SSL] [LZO2] [PKCS11] built on Dec 15 2011 Tue Dec 18 16:34:27 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Tue Dec 18 16:34:27 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Dec 18 16:34:27 2012 LZO compression initialized Tue Dec 18 16:34:27 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue Dec 18 16:34:27 2012 Socket Buffers: R=[65536-65536] S=[65536-65536] Tue Dec 18 16:34:27 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue Dec 18 16:34:27 2012 Local Options hash (VER=V4): '41690919' Tue Dec 18 16:34:27 2012 Expected Remote Options hash (VER=V4): '530fdded' Tue Dec 18 16:34:27 2012 UDPv4 link local: [undef] Tue Dec 18 16:34:27 2012 UDPv4 link remote: ..*.:1194 Tue Dec 18 16:34:27 2012 TLS: Initial packet from ..*.:1194, sid=4d1496ad 2079a5fa Tue Dec 18 16:34:28 2012 VERIFY OK: depth=1, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:28 2012 VERIFY OK: depth=0, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue Dec 18 16:34:29 2012 [myservername] Peer Connection Initiated with ..*.:1194 Tue Dec 18 16:34:32 2012 SENT CONTROL [myservername]: 'PUSH_REQUEST' (status=1) Tue Dec 18 16:34:32 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: timers and/or timeouts modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: --ifconfig/up options modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: route options modified Tue Dec 18 16:34:32 2012 ROUTE default_gateway=192.168.1.254 Tue Dec 18 16:34:32 2012 TAP-WIN32 device [Local Area Connection] opened: \.\Global{F0CFEBBF-9B1B-4CFB-8A82-027330974C30}.tap Tue Dec 18 16:34:32 2012 TAP-Win32 Driver Version 9.9 Tue Dec 18 16:34:32 2012 TAP-Win32 MTU=1500 Tue Dec 18 16:34:32 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.8.0.6/255.255.255.252 on interface {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} [DHCP-serv: 10.8.0.5, lease-time: 31536000] Tue Dec 18 16:34:32 2012 Successful ARP Flush on interface [26] {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} Tue Dec 18 16:34:37 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD ..*. MASK 255.255.255.255 192.168.1.254 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 10.8.0.1 MASK 255.255.255.255 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 Initialization Sequence Completed

    Read the article

  • Cannot seem to disable ability to view temporary internet files via group policy

    - by user162707
    Windows XP Pro SP3, IE8 (8.0.6001.18702), within local gpedit.msc I did the below: User Config/Admin Temp/Windows Comp/IE enabled: disable changing temporary internet file settings User Config/Admin Temp/Windows Comp/IE/Delete Browsing History enabled all (11 items) However there is a loophole that lets me still wipe history & other files via: Tools, Internet Options, Browsing History, Settings, View Objects, delete everything, hit up arrow, go to History (hidden folders has to be on), delete everything Only way around this I can see is to disable General Internet Options Page via group policy, setup NTFS folder restrictions on that temp internet files (worried about adverse affects like not being able to store them), or further grind-down group policy somewhere else to prevent deleting files. Just odd group policy wouldn't have a settings to simply disable the Browser History Settings button (as it further shows the location which a user could just go to). So just curious if someone can confirm maybe this is simply not available in group policy & their suggested action

    Read the article

  • Local Area Connection in Slacware 13

    - by asdasd
    I have windows xp and slackware 13 on one computer, and the ISP provided me a new modem. There was manual how to configure it, so i start the web browser and typed it's ip address 192.168.1.1 and the web interface of the modem appeared so i logged in, that was easy. But under slackware, i don't know how to enter in the modem config / web interface. I type in 192.168.1.1 but it's not working. Here's the output of ifconfig eth0 : eth0 Link encap:Ethernet HWaddr 00:a1:b0:01:18:28 inet addr:169.254.73.8 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 Memory:febff400-febff4ff How can i log in into the modem from linux, i.e. find it's assigned ip under slackware ? Thank you.

    Read the article

  • dhclient configures /etc/resolv.conf with invalid entry

    - by kubal5003
    I'm trying to figure out why running dhclient on my interface sets /etc/resolv conf to the ip number of my gateway(router). This entry is invalid and each and every time causes inability to resolve any address. I would like to: stop dhclient from overwriting the /etc/resolv.conf or make dhclient write there the valid dns ip from my router More on the environment: I'm using virtual Debian Wheezy as a client system on Windows Seven x64. It is run by Virtualbox with networking mode set to bridged (all packets from debian are injected to my network interface on windows). If I manually configure the /etc/resolv.conf then everything works fine. Doing this on every boot is quite annoying.. PS I know I can write a script to do it for me, but this is not the solution I want. //edit router ip: 192.168.1.100 /etc/resolv.conf AFTER running dhclient eth0: "nameserver 192.168.1.100" what I would like the /etc/resolv.conf to look like: "nameserver 89.202.xxxx" (I don't have to provide the real ip do I? )

    Read the article

  • What is the impact of Windows 8 with UEFI on normal users?

    - by Sam
    I am a normal man-in-the-street computer user and so do not really understand what this is about, but I want to. Can someone please explain to me if: The Windows 8/UEFI secure boot thing will make it impossible to run normal/legacy applications in Windows 8 (as they will be unsigned)? It will turn Windows into an Apple-like system where only Microsoft approved applications can be run? As I say, I'm a normal user, and that is the overall impression I have from reading all the blogs, etc about it. If, on the other hand, all it does is make sure the system is booting a signed OS, how does this prevent malware (which is what at least two Microsoft blogs that I read seemed to be saying), given that most malware is not part of the boot process? The only way I can see this making sense is if it is ensuring that all OS components are signed. Is that it? Like I say, I'm a mortal, so please don't get technical on me, but rather explain how it will affect me, the user.

    Read the article

  • How to find ip address of my Asus RT-AC86U in Access Point mode?

    - by WilliamKF
    I'm using an Asus wireless router model RT-AC68U and can connect fine to the internet using it wirelessly. I configured the router to be an Access Point, but having done so, I can no longer locate the GUI to adjust the router as I have no idea what its IP Address is anymore. The router is plugged into a cable modem and router which is a model SMCD3G is a business class gateway labeled Comcast Business IP Gateway. This gateway is assigning ip addresses in the range 10.1.10.XX and I went to the web interface at 10.1.10.1 and listed the connected devices and see my laptop which is connected to the Asus access point along with a few other devices, but none of the devices listed are the Asus router (I tried all the six ip addresses listed). How can I determine the IP Address of my Asus router in access point mode so I can see the GUI interface again to control the router other than by doing a factory reset?

    Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >