Search Results

Search found 14240 results on 570 pages for 'upload manager'.

Page 372/570 | < Previous Page | 368 369 370 371 372 373 374 375 376 377 378 379  | Next Page >

• Restoring factory image of HP Laptop

  - by Ahmed

  I use a HP G62. I am unable to use my recovery disk to restore to factory settings. I had no problems earlier until I created an additional partition which I hear might have changed my hard disk to dynamic. How do I get back to 'normal'? I don't mind formatting the disk. I just want my factory OS back. .............. i get an error message at about 69 percent telling me that the restoration process failed. I'm using the factory image disks i created using the hp recovery manager. I have tried formating the hard drive clean and then restoring woth the cd, it didn't work. I was always able to restore before i created that partition.

  Read the article

• Wake network adapter from deep sleep mode

  - by BeatMe

  I recently buyed a new Mainboard (Asrock ALiveXFire) and got some trouble with the network adapter. After switching my Windows 7 x64 in energey saving mode and returning from it, my network adapter couldn't be found. After some googling I found out, that apparently my network adapter has been put in a deep sleep mode and didn't reactivate. Their solution was to switch the PC off, take out the RAM and the CMOS battery for some time. After that, the adapter should be powered on again, but that didn't happen for me. I waited several hours before turning my PC on again, but that didn't help. Formatting and reinstalling didn't help either. The network adapter is not found in the hardware manager and reinstalling the drivers didn't help. I have the newest BIOS installed on the mainboard. I literally don't know what to try next. I'm thinking of returning my board, but I would like to avoid the hassle.

  Read the article

• Couple folders went 'access denied' in Windows. Why and how to fix?

  - by Nathaniel

  So, after a failed Windows 7 install, I put XP back on, and had a adrenaline shot when I got an access denied on a couple of my backed up folders. I already tried the instructions here at Microsoft KB, but it didn't fix it. I did add myself with full permissions on the main section of the Security tab, though, and that gave me access into the folder (I could do it in XP Home because of the Windows NT SP4 Security Configuration Manager). However, it appears some subfolders are still inaccessible. Two questions, then. Why exactly did this happen and how do I fix it?

  Read the article

• Ubuntu 12.04 Netinstall URL? Xen Host

  - by notFound

  Well I have an Xen server, I've got a CentOS container up fine but a friend of mine wants (oh god) Ubuntu Server 12.04, why he can't use Debian is beyond my understanding. But anyways, I can't remember how I installed the CentOS container but I'm giving virt-manager a try now, since I don't have a disk image already the only option is to get a Network Install URL since I'm using PV. So does anyone know what I should type in there, if it was CentOS I could easily type http://mirror.centos.org/centos/6.2/os/i386 for example. The furthest I've got in finding a suitable URL is http://archive.ubuntu.com/ubuntu/dists/precise/ but that of course wont work. Any ideas?

  Read the article

• Scripting a database copy from MS Sql 2005 to 2008 without detach/backup/RDP

  - by James Santiago

  My goal is to move a single SQL 2005 database to a seperate 2008 server. The issue is my level of access to both servers. On each I can only access the database and nothing else. I cant create a backup file or detach the database because I don't have access to the file system or to create a proxy. I've tried using the generate script function of sql 2005 management studio express to restore the schema but receive command not supported errors when attempting to execute the sql on the new database. Similarly I tried using EMS SQL Manager 2005 Lite to script a backup of the schema and data but ran into similar problems. How do I go about acomplishing this? I can't seem to find any solutions outside of using the detach and backup functions.

  Read the article

• Troubleshooting source of heavy resource-usage on a windows server 2008 running multiple sites

  - by batman_man

  Hi, I am running about 10 asp.net websites on a hosted virtual server. The server runs Server 2008 - each website is backed by its own database running on SQL server 2008 on the same box. Lately the box has seemed really slow. The only kind of discovery i could think of doing was looking in the task manager, where i can see w3wp and sqlserver.exe jumping to 40% cpu usage every 5-10 seconds. What are the steps i can take to determine which of my websites is taking these resources and or what database is getting hit the most? I have of course ssms installed on the machine as well. As you can tell, my sysadmin skills are very very limited - any help would be much appreciated.

  Read the article

• Windows 8 will only recognize the Blu Ray ROM, if the install disk is present at boot time

  - by aceinthehole

  If I have the install disk in the blu ray ROM drive at boot time and subsequently remove the disk and replace it with blu ray media everything functions as I'd expect. However, if I have no media present, or another disk in the drive at boot time, then windows 8 does not seem to recognize that the blu ray player is even present in the computer. It is not present in the 'my computer' screen, device manager does not show the player, and scanning for new hardware yields nothing. It seems that the driver is installed and working as expect, what is it about having the windows 8 install disk in the drive or not that would cause this kind of behavior?

  Read the article

• Re-deploy Reports on SCOM Management Packs

  - by Gabriel Guimarães

  I've migrated Reporting Services on a SCOM 2007 R2 install, and noticed that the reports have not being copied. I can create a new report, but the ones I've had because of the management packs are gone. I've tried re-applying the Management Packs however it doesn't re-deploy them and when I try to access for example: Monitoring - Microsoft Windows Print Server - Microsoft Windows Server 2000 and 2003 Print Services - State View - select any item and click Alerts on the right menu. I get the following error: Date: 12/24/2010 12:40:35 PM Application: System Center Operations Manager 2007 R2 Application Version: 6.1.7221.0 Severity: Error Message: Cannot initialize report. Microsoft.Reporting.WinForms.ReportServerException: The item '/Microsoft.SystemCenter.DataWarehouse.Report.Library/Microsoft.SystemCenter.DataWarehouse.Report.Alert' cannot be found. (rsItemNotFound) at Microsoft.Reporting.WinForms.ServerReport.GetExecutionInfo() at Microsoft.Reporting.WinForms.ServerReport.GetParameters() at Microsoft.EnterpriseManagement.Mom.Internal.UI.Reporting.Parameters.ReportParameterBlock.Initialize(ServerReport serverReport) at Microsoft.EnterpriseManagement.Mom.Internal.UI.Console.ReportForm.SetReportJob(Object sender, ConsoleJobEventArgs args) The report doesn't exist on the reporting services side. how do I re-deploy this reports? Thanks in advance.

  Read the article

• Mac OS X Server add server user

  - by Meltemi

  What's the recommended way to add a user to Mac OS X Server that doesn't need all the hoopla associated with Workgroup Manager? There are many users pre-configured in Mac OS X Server (www, root, ldapadmin, etc.) that don't have "Full Name" or mail accounts, etc. I'd like to create a 'svn' user to be the owner of our Subversion Repository as per this tutorial: If you've decided to use either Apache or stock svnserve, create a single svn user on your system and run the server process as that user. Be sure to make the repository directory wholly owned by the svn user as well. From a security point of view, this keeps the repository data nicely siloed and protected by operating system filesystem permissions, changeable by only the Sub- version server process itself. Wondering if there's a way outside of WorkgroupManager and OpenDirectory as this account will be entirely server based. Is this still sound advice under OS X Server? If so what's the easiest way to create the user (Mac OS X Server doesn't seem to respond to useradd).

  Read the article

• Server Core remote management from Windows 7 machine

  - by Robert Koritnik

  I've installed Remote Server Administration Tools for Windows 7 because I would like to administer my Windows Server 2008 R2 Server Core machine. The problem that I'm getting when I try to run Server Manager is: Connecting to remote server failed with the following error message: Access is denied. For more information, see the about_Remote_Troubleshooting Help topic. This is what I've done so far: I'm running WinRM service on both machines (Server and Window 7) I've added my server to trusted hosts on my Windows 7 machine: winrm set winrm/config/client @{TrustedHosts="WINSRV2"} I've added registry entry on Windows 7 machine: reg add HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System /v LocalAccountTokenFilterPolicy /t REG_DWORD /d 1 /f I've enabled Remote Management inbound rule on server firewall using CoreConfigurator 2.0 both machines are in the same subnet and when I search for network machines on Windows 7 I see my server. Question What else should I do to make it work? I would like to run several different remote management tools against my server machine.

  Read the article

• How to run UNetBootin (or similar) on Linux?

  - by zharvey

  I am trying to install UNetbootin on my Linux Mint (12 - KDE) machine and it will not run. I downloaded the Linux version of it (downloads as a unetbootin-linux-581 file) and set its permission to chmod +x unetbootin-linux-581. I've tried running it every way I can think of: Double-clicking it from the dolphin file manager Running ./unetbootin-linux-581 Running sh ./unetbootin-linux-581 Running unetbootin-linux-581.sh Nothing seems to be working. So I downloaded it on my Linux Ubuntu (12.04) machine, in case UNetbootin doesn't run on Mint for some reason, and am getting the same results. How do I run it, or what do I need to do to be able to run it?!? Thanks in advance!

  Read the article

• GIMP Slow Startup

  - by muntoo

  Is there any way to speed up GIMP's startup time on Windows Vista Home Premium 32-Bit 1.6 [Dual] Intel Processors? On XP [different computer], it loads in less than 3 seconds. On Vista, it takes 20 seconds: 2 Seconds (other - fonts, brushes, etc) 18 Seconds (extension-script-fu) It just freezes at extension-script-fu. Looking at ProcessExplorer (or Task Manager, whatever), I see that it's not taking any CPU. EDIT: it does seem to be taking 50% of the CPU. It gets stuck for about 18 seconds, then starts working again, and the actual GIMP program pops up [...finally]. I have the latest stable version running (I think). I tried it with XP SP2 Compatibiliy mode and/or Run As Administrator, but that didn't help. EDIT: One way would be to disable script-fu. Does anyone know how to disable it at startup? (NOTE: Just wanted to point out that the title and the tags are the same. :D )

  Read the article

• Rewind print job under Windows Server 2008

  - by FooLman

  Hello, We are in the transition from Novell NetWare to Windows server 2008. In case of the printer server we print jobs thousands of pages long. NetWare printer manager has a handy function which allows to rewind a print job to a specified page. In case of a paper jam at the 750 page on a 800 page document this is really convenient. Does anybody know if there is a solution for this? The lists printed are in plain ascii lists with printer command characters embedded, and we are using dot matrix printers. Thanks for any help or suggestion. Regards.

  Read the article

• How to repair the boot selection on grub?

  - by Zignd

  I had installed on my computer as a dual-boot: Debian Squeeze and Windows XP, so I decided to install Windows 8 just to test and then I would remove it and install in its place Debian Wheezy as dual-boot with Windows XP, that was already installed. During the Debian Wheezy installation, I deleted the Windows 8 partition to install Debian W. on its place. The problem is, that after the installation finished I rebooted the computer and on the grub menu was written: Debian Wheezy and Windows 8 (loader) - this Windows 8 (loader) is a boot manager as grub, and after the Win8 installation I was capable of choose between Win8 and WinXP. And when I select Windows 8 (loader) it says the Windows 8 is corrupted and is not possible to boot Windows XP. So, after that, I would like to know, how can I get Windows XP on the grub menu? Because I know its there (the Windows XP), but I can not boot it from grub. Observation: I already tried update-grub, but it only finds Debian W. and Windows 8.

  Read the article

• Reverse rdesktop or VNC overlay image!

  - by carlesso

  Hi all. I've got a central server (linux based) and many clients (Windows XP Embedded, afaik) in public places around my country. I need to have these clients to connect to the server with a "reverse" tunnel, that is to say that I need to control the clients from the server but the connection is initialized by clients. The requirement is that, during the connection, an overlay image (or something like that, like a modified version of login screen) is displayed. Some stuff like "Work In Progress". My first idea was to use vncviewer -listen and vnc in reverse mode, but cannot understand how to obfuscate the work I'm doing. Other idea was to use rdesktop in "reverse" mode, but it seems it does not support it. Using rdekstop reverse seems the nicest solution (I can login back the user was in before connection, the login manager - which I can modified - is displayed), but any hint will be appreciated! Thanks in advance!

  Read the article

• How to dismiss the Windows 8.1 Upgrade banner?

  - by user81430

  As of today, my Windows 8 system is displaying a large banner covering about a quarter of the screen, demanding that I upgrade to Windows 8.1 for free. The banner helpfully informs me that that I can continue to use the computer while the upgrade is downloading. There's a button to go to the store for the upgrade, but no other choices, such as No Thanks, Maybe Later, or Absolutely Not. I can't find a way to dismiss the banner, and I can start programs but can't give them focus while the banner is present. So I'm dead in the water. How can I fix this? Bringing up Task Manager doesn't give me any options. My employer doesn't yet support Windows 8.1 (which is also an issue, but beyond my control) so I won't be able to connect to work if install the upgrade. So there is no way on God's green earth that I'm going to install this upgrade now.

  Read the article

• Disabling a touchpad in Windows

  - by Shamaoke

  I want to permanently disable a touchpad in Windows running on my laptop, since firstly, I use a mouse, and secondly, when I work, I often touch it accidentally what causes definite inconviniences. I tried the following approaches to disable it but with no result: Turned it off through BIOS — there's no such function there; Turned it off through the touchpad configuration utility — there's no such function there; Turned it off through the device manager — the disable button is inactive; Turned it off through a hotkey (Fn + F1 in my case) — the hotkey doesn't work; Uninstalled the proprietary driver — Windows automatically downloaded the standard driver; Uninstalled the standard driver and turned off the automatic driver download function (Win + R ? "systempropertiesadvanced" ? Hardware ? Device Installation Settings) — all the same, Windows downloaded and installed the driver. How can I disable a touchpad? Windows 7; the Alps touchpad.

  Read the article

• Cannot import video from a DV camcorder over FireWire

  - by qbeuek

  I have a JVC GR-D320 miniDV camcorder that has a FireWire interface. I recently upgraded to Windows 7 RTM (64 bit, fresh installation). When I connect my camcorder through FireWire, I can see it in Device Manager without any warnings or problems, but I cannot capture videos from my miniDV tapes. After connecting, AutoPlay displays "Import Video could not find a compatible digital video device. Verify that the digital video device is properly connected and turned on." When using Windows Live Photo Gallery after selecting the import option, my camera is not listed. The camera used to work perfectly on the same hardware before upgrading to Windows 7 RTM 64 bit (it used to work fine on Windows XP SP3 32 bit). Googleing revealed that people had the exact same problems in Vista, but no solution was provided. Any help?

  Read the article

• How to use new disk space after extend attached SAN disk

  - by Edu Lomeli

  I have extended the space of my SAN vDisk from 1TB to 1.2TB, but Windows Explorer doesn't show the new size. After resize the vdisk in the SAN Manager, the Disk Management utility shows the 200GB unallocated space, then I resized the partition to use the unallocated space to get a 1.2TB partition, the process was succesfully, but in the Windows File Explorer the disk still have 1TB of total space. Win version: Windows Storage Server Enterprise 2007. Do I need to restart the server? How can I use the new extra space without rebooting?

  Read the article

• How can I delete virtual networks from command line?

  - by David Cobb

  I have Hyper-V Server 2008 R2 (without GUI) running at my colo for a week. I was connected via RDP and could use the menu interface and command line. I figured out how to connect Hyper-V Manager from my Win7 laptop (THANK YOU HVREMOTE!), and created and installed my VM. I created a virtual network that didn't work (no connectivity from my VM) so I created another using different settings, and now have lost access to the Hyper-V host. No ping, no RDP. Since I don't have console access, I cannot troubleshoot. I believe if I deleted the Virtual Networks I'd regain access, but I need a command line instruction for this, that the staff onsite could enter to accomplish this. I find no help anywhere obvious (MSDN, etc), the keywords are too general. Can anyone refer me to simple steps how to do this over command line or with the menu based interface on the console?

  Read the article

• How to prepare and secure a Macbook Pro for work/office?

  - by sunpech

  I plan to use my Macbook Pro at work/office. Before I do so, I will need to speak to my manager on how to properly prepare and secure it since this is the first Mac that will be regularly used on the network in the office and company intranet. The intranet comprises mostly of PCs running Microsoft Windows XP, Server 2003, and Windows 7. So there's definitely a Microsoft-only culture in the office, and the infrastructure/networking team are mostly unfamiliar with non-Microsoft technology and software. What steps and software would I need to prepare and secure my Macbook Pro for work/office? Antivirus/Spyware software for Mac required/necessary? What options do I have to encrypt files, or possibly the whole drive/partition? What network/firewall settings should be enabled?

  Read the article

• Getting "GRUB loading ... no such partition"?

  - by shameedp

  I am having a dual os, windows 7 and linux, the c drive have 20 GB, in which 5 GB is allocated for windows 7 (original) and 15 gb for linux since the spacing for windows is very low i used EaseUS partition manager and deleted my linux OS, and merged the unused space into my C drive, now it becomes 20GB, the things, after the reboot, I am getting GRUB loading. Welcome to GRUB! error: no such partition. entering rescue mode. . . Kindly help me guys the problem i am facing is i dont have a DVD drive to resolve it, using recovery mode. Waiting for your reply guys. in ls command i have (hd0) (hd0,msdos8) (hd0,msdos7) (hd0,msdos6) (hd0,msdos5) (hd0,msdos2) (hd0,msdos1)

  Read the article

• Use an unsigned driver in Windows 7 x64

  - by rjmunro

  I'm trying to use the RBC9 SpaceNavigator TEST x64 build drivers for my SpaceNavigator 3d joystick so that it can work as a normal joystick in games like Quake. Unfortunately, I get the error "This version of windows requires all drivers to have a valid digital signature" and in the "Device status" in device manager, I get "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)". Is there a way to work around this issue?

  Read the article

• Missing Items from Start Menu

  - by ChrisHDog

  I used to be able to search/open items from my start menu, but recently items have gone "missing". Example: I used to be able to hit the start menu, type "iis" and the top item would be iis manager and I could open and run ... now I get a list of items that are not IIS The same is true with typing "servi" - previously i would get Services (i.e. open local services), now it isn't showing I've checked the properties on Customise Start Menu for "Search other files and libraries" and it is selected as "Search without public folders" ... is there something else that is happening? It seems like something has changed, but I can determine what/how to revert to what it was.

  Read the article

• No GUI after upgrade to Ubuntu 9.10 (boots to command line)

  - by Gathris

  I have just upgraded to Ubuntu 9.10 (network upgrade using the update manager, from 9.04 which had different graphics related problems) and when I try to boot into it all I get a small Ubuntu logo, flickering text and then the tty1 command line with a logon prompt. startx gives following error: Fatal server error: no screens found I traced down a tutorial that said I needed the latest graphics drivers (Gigabyte ATI Radeon 4650 HD installed with 9.10 catalyst drivers) so I did using the 'sh' command and a USB stick (I have a working Windows partition) and it installed fine but did not fix the problem. Edit: Thanks to UK and Arjan van Bentem below I was able to understand the full error message of start x: Parse error on lone 2 of /etc/X11/xorg.conf 'nameserver' is not a valid keyword in this section Fatal server error: no screens found This has nothing to do with a graphical error (sorry if I misled anyone) but the xorg.conf file has 3 lines in it and lines 2-3 have an entry 'nameserver'. Using the nano command I commented out (using a # before the entries) the nameservers and can now boot Ubuntu. Thanks to everyone for their help.

  Read the article

< Previous Page | 368 369 370 371 372 373 374 375 376 377 378 379  | Next Page >