Search Results

Search found 11188 results on 448 pages for 'django manage py'.

Page 374/448 | < Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >

• How can I recover a Fedora 12 installation that is showing signs of disk errors?

  - by Bob Cross

  I am currently overseas (i.e., very far from my normal library of tools) and my primary machine that would normally act as the data server in the performance test that we're trying to run is failing to boot to Fedora 12 properly. This is a machine that, as of yesterday, was booting fine. However, this morning, very strange portions of the boot process were complaining with messages such as "unexpected 0x0 in rpcbind" and "bad file descriptor" (I don't have the error in front of me - scavenged a windows installation to get onto serverfault). Eventually, the boot hung for a long time at the NFS service and then brought up what looked like the KDE login screen but neither the mouse nor keyboard functioned. In olden days, I would try to get to a point where I could manage to run fsck and pray that the bad sectors would come back into alignment just long enough for me to scrape the critical data off of the machine. However, now that we live in the future, it seems like our options in situations like this should be a little more varied. Is there a way to recover a Fedora 12 installation with bad disk sectors that won't boot properly? For completeness, I am comfortable working with bootable recovery distros-on-CD and such but I don't know which one is likely to work best with modern Fedora. In the absence of guidance, I'm frantically torrenting the Fedora 12 Live CD and DVD, hoping to try rescue mode before tomorrow morning.

  Read the article

• Ubuntu Wubi "drive" failure; mount drive in XP?

  - by 618034

  Hi there, I installed the Wubi distribution of Ubuntu on a separate partition (which is silly, since why do I care if Windows can still manage the partition?) a few months back; it was pretty awesome, until Linux hosed. At this point, I can get Ubuntu to boot if I try really hard through grub, but once it does start, the screen is hosed, so no dice. At this point, I'd like to wipe it all and start over, but I need to get some stuff off the "disk". The Wubi install makes this difficult, since the "disk" is a flat file on an NTFS partition. I've done just about everything I can think of — I renamed the virtual disk .iso, mounted it with VirtualCloneDrive, then used whatever magic EXT3 (EXT4?) readers I could dig up on the Internet to parse the mount — but nothing's working. Can you offer any suggestions? The "disk" is currently in D:\ubuntu\disks\root.iso. Many thanks! (I may be high-latency at the moment, apologies if I don't address follow-ups quickly)

  Read the article

• Migrating away from LVM

  - by Kye

  I have an Ubuntu home media server setup with 4.5TB split across a few hard-drives (1x3TB, 2x1TB) and I'm using LVM2 to manage the volumes. I have recently added a 60GB SSD to my server, and I wish to use it to house the 'root' partition of my server (which is currently under the LVM group). I don't want to simply add it to the LVM volume group, because (afaik) there's no way to ensure that the SSD will be used for the root filesystem. If I just throw it at the VG, it may be used to house my media, which would defeat the purpose of having the SSD in the first place. I feel that my only solution is to somehow remove my root partition from the LVM setup and copy it across to the SSD. My boot partition is, of course, not part of the LVM group. My disk setup is as follows: 60GB SSD: EMPTY. 1TB HDD: /boot, LVM space. 1TB HDD: LVM space. 3TB HHD: LVM space. I have a few logical volumes. my root (/), a 'media' volume for my media collection, a backup one for my network backups.etc. Does anyone have any advice as to how to go about this? My end goal is to have the 60GB SSD used for my boot and root partitions, with everything else on the 3TB/1TB/1TB hard-drives.

  Read the article

• Active Directory Password Formats

  - by Brent Pabst

  Hi, I'm working on an open source project that will manage active directory users. I am looking for feedback from Windows/Active Directory Admins on the formats of usernames they prefer or their organization uses. I want to make sure the software allows admins to use the most popular formats when new users are created. Here is the list I have so far: 1. <firstname><lastname> 2. <lastname><firstname> 3. <lastname><firstinitial> 4. <lastname><firstinitial><middleinitial> 5. <firstinitial><lastname> 6. <firstinitial><middleinitial><lastname> 7. <firstname><lastinitial> In addition how do you handle multiple identical names? So if two John Smith's exist do you append a numeric number, or interject a middle initial or name to solve the problem? Thanks for the feedback

  Read the article

• Managing an application across multiple servers, or PXE vs cfEngine/Chef/Puppet

  - by matt

  We have an application that is running on a few (5 or so and will grow) boxes. The hardware is identical in all the machines, and ideally the software would be as well. I have been managing them by hand up until now, and don't want to anymore (static ip addresses, disabling all necessary services, installing required packages...) . Can anyone balance the pros and cons of the following options, or suggest something more intelligent? 1: Individually install centos on all the boxes and manage the configs with chef/cfengine/puppet. This would be good, as I have wanted an excuse to learn to use one of applications, but I don't know if this is actually the best solution. 2: Make one box perfect and image it. Serve the image over PXE and whenever I want to make modifications, I can just reboot the boxes from a new image. How do cluster guys normally handle things like having mac addresses in the /etc/sysconfig/network-scripts/ifcfg* files? We use infiniband as well, and it also refuses to start if the hwaddr is wrong. Can these be correctly generated at boot? I'm leaning towards the PXE solution, but I think monitoring with munin or nagios will be a little more complicated with this. Anyone have experience with this type of problem? All the servers have SSDs in them and are fast and powerful. Thanks, matt.

  Read the article

• Can any postfix guru assist me determine how emails are still being sent via my server from unauthorized sources?

  - by Dave

  Hi all, I'm getting a little concerned as I run a small server hosting a number of websites and manage the email for a few dozen people. Just recently though I've had a couple of notifications from spamcop alerting me that spam has been sent from my server, and when I have a look over the logs from time to time I can indeed see that there are many repeated attempts of mail being sent from my server. Most of the time it gets knocked back from the destination servers but sometimes its getting through. Unfortunately I'm not linux or postfix expert, I can get by but had though I had my machine locked down quite securely, I don't allow relaying, when I check the online DNS/MX tools they tend to report my server as being OK so I'm not sure where to take it now and hoping someone might be able to throw me a few pointers. I get lots of entries like this in my MAIL.INFO log Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 66B88257C12F: from=<>, size=3116, nrcpt=1 (queue active) Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 614C2257C1BC: from=<[email protected]>, size=2490, nrcpt=3 (queue active) and Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6471]: 0A316257C204: to=<[email protected]>, relay=none, delay=384387, delays=384384/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6470]: 5848C257C20D: to=<[email protected]>, relay=none, delay=384373, delays=384370/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) then there tends to be connection timeouts, so from what I see even though I had relaying disabled.. something is getting by and trying to send.. So if you can help that will be greatly appreciated, and any further logging/config info I can supply. Thanks

  Read the article

• Central Authentication For Windows, Linux, Network Devices

  - by mojah

  I'm trying to find a way to centralize user management & authentication for a large collection of Windows & Linux Servers, including network devices (Cisco, HP, Juniper). Options include RADIUS/LDAP/TACACS/... Idea is to keep track with staff changes, and access towards these devices. Preferably a system that is compatible with both Linux, Windows & those network devices. Seems like Windows is the most stubborn of them all, for Linux & Network equipment it's easier to implement a solution (using PAM.D for instance). Should we look for an Active Directory/Domain Controller solution for Windows? Fun sidenote; we also manage client systems, that are often already in a domain. Trust-relationships between Domain Controllers isn't always an option for us (due to client security restrictions). I'd love to hear fresh ideas on how to implement such a centralized authentication "portal" for those systems.

  Read the article

• Home Server: cpu virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

  Read the article

• Grant HTTP access based on unix user group

  - by Sander Marechal

  Is it possible to grant network access or HTTP access based on a user's group? At my company we want to set up an internal composer server using Satis to manage packages for the projects we write (e.g. on repository.mycompany.com), with the packages themselves in our SVN server (svn.mycompany.com). We have several webservers with many different users on them. Some users should be able to reach the composer and SVN server. Some should not. Users that should be able to reach these servers all belong to the same group. How can I set up Apache on the Composer and SVN server to only grant access to those users in that group? Alternatively, can I set up the webservers in such a way that only users from that group are able to make a connection to our Composer and SVN servers? The best thing we have come up with so far is using SSL client certificates. We simply place a client certificate on all servers which can be used to access Composer and SVN. Only the right usergroup will have read access to the certificate. A bit clunky but it may work. But I'm looking for something better.

  Read the article

• Dell 2970 - HP 1/8 G2 autoloader keeps falling off LSI 2032 SCSI chain

  - by middaparka

  I've a somewhat irritating problem with a Dell 2970 that has a HP 1/8 G2 autoloader (the Ultrium LTO 2 model) attached to the Dell/LSI 2032 non-RAID SCSI card. In essence, sometimes the autoloader/drive completely fails to appear on the SCSI chain (i.e.: there's neither a media changer or tape drive present within the device manager) and sometimes it appears but then subsequently disappears at a seemingly random (yet always inconvenient) time, resulting in backup failures. On most occasions, there are simply no errors logged in the system event log, but I did manage to capture a series of LSI_SCSI event ID 11 ("The driver detected a controller error on \Device\RaidPort0") errors followed by an event ID 129, ("Reset to device, \Device\RaidPort0, was issued") error during testing. I've tried two different cables, both with the same effect – sometimes the autoloader appears (for a while), sometimes it's completely absent. There's only one terminator I've tried to use, but as I've since successfully tested the autoloader on multiple occasions (albeit via a Adaptec U160 card on a different machine), my gut feel is that the issue doesn't lie with the terminator, or indeed the autoloader itself. As such, I'm just wondering if anyone has any ideas? It's most likely not relevant, but this is all under Windows SBS 2008, running Backup Exec 12.5 SBS edition (the Dell version), both fully patched. Addidtionally, the autoloader is running the latest firmware. It's been a while since I've dealt with anything SCSI, so all suggestions will be gratefully, gratefully received.

  Read the article

• Server Manager from Windows 2008 to Hyper-V 2008 R2?

  - by Roger Lipscombe

  My workstation is running Windows Server 2008. I do not have local admin privileges. I have a Hyper-V Server 2008 R2 (i.e. Core+Hyper-V) box. On that box, I do have local admin privileges. I can Remote Desktop to the box; Hyper-V Manager works fine (outside of Server Manager). It's just that there are some things that are easier to do in Server Manager (partition disks, etc.) than at the command line. I'd like to use Server Manager on my workstation to manage the Hyper-V box. However: When I run Server Manager on my workstation, it prompts for elevation, and won't then let me connect to another server. If I attempt to run MMC and then add "Server Manager" as a Snap-in, it doesn't prompt me for the server name. Then it complains that I'm not an Administrator. It doesn't provide for connecting to another server. The Remote Server Administration Tools (RSAT) are for Windows Vista and Windows 7 RC. These don't install on Windows 2008.

  Read the article

• How To Find Reasons of Why Site Goes Online/Offline

  - by HollerTrain

  Seems today a website I manage has been going online and offline throughout the entire day. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I use a program that pings the server every minute and when the server is not responding me it emails me, so I can know exactly when the site is online and offline. The site between 8pm to 12pm 12.28, and around the 1a hour early morning 12.29 (New York City timezone, and all times below are in same timezone). At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• keepalived issues on xen domU

  - by David Cournapeau

  Hi, I cannot manage to run keepalived correctly on xen domU. I am following this link for configuration, and it works great on some local VM (running with KVM). If I set up the exact same configuration, but on xen domU, it does not work: both servers do not see each other and decide to be master (10.120.100.99 being the virtual IP) $ sudo ip addr sh eth0 # host1 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:16:3e:78:f5:31 brd ff:ff:ff:ff:ff:ff inet 10.120.100.104/24 brd 10.120.100.255 scope global eth0 inet 10.120.100.99/32 scope global eth0 inet6 fe80::216:3eff:fe78:f531/64 scope link valid_lft forever preferred_lft forever $ sudo ip addr sh eth0 # host2 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:16:3e:51:36:20 brd ff:ff:ff:ff:ff:ff inet 10.120.100.105/24 brd 10.120.100.255 scope global eth0 inet 10.120.100.99/32 scope global eth0 inet6 fe80::216:3eff:fe51:3620/64 scope link valid_lft forever preferred_lft forever Is there a way I could debug this - it seems some people are able to use keepalived on xen following some mailing list, but without much info on their config.

  Read the article

• FastCGI Error when installing PHP on IIS7.5

  - by ytoledano

  I'm trying to install MediaWiki on a Win2008r2 server, but can't manage to install PHP. Here's what I did: Grabbed a Zip archive of PHP and unzipped it into C:\PHP. Created two subdirs: c:\PHP\sessiondata and c:\PHP\uploadtemp. Granted modify rights to the IUSR account for the subdirs. Copied php.ini-production as php.ini Edited php.ini and made the following changes: fastcgi.impersonate = 1 cgi.fix_pathinfo = 1 cgi.force_redirect = 0 open_basedir = "c:\inetpub\wwwroot;c:\PHP\uploadtemp;C:\PHP\sessiondata" extension = php_mysql.dll extension_dir = "./ext" upload_tmp_dir = C:\PHP\uploadtemp session.save_path = C:\php\sessiondata Install Web server role, selected CGI and HTTP Redirection options. In the Handler Mappings: Added Module Mapping. Entered the following values: Path = *.php, Module = FastCgiModule, Executable = c:\php\php-cgi.exe, Name = PHP via FastCGI. Created a test page into wwwroot directory: phpinfo.php and set the contents like this: < ?php phpinfo(); ? Browsed to http://localhost/phpinfo.php But then I get: HTTP Error 500.0 - Internal Server Error An unknown FastCGI error occured Detailed Error Information Module: FastCgiModule Notification: ExecuteRequestHandler Handler: PHP via FastCGI Error Code: 0x800736b1 Requested URL: http://localhost:80/phpinfo.php Physical Path: C:\inetpub\wwwroot\phpinfo.php Logon Method: Anonymous Logon User: Anonymous Does anyone know what I'm doing wrong here? Thanks.

  Read the article

• Are there any open source reseller packages?

  - by Tom Wright

  My department has just been given the right/responsibility to manage our own VPS. The idea being that the bureaucracy will be less for the many small web projects we run. Since each project will be managed by a different team, I was planning on approaching a shared hosting model. Are there any free pieces of software that would help automate the provision of resources each time a team request a new project? Most of the projects have identical requirements - basically LAMP - so it would be these resources that I would want provisioning (and de-provisioning, if that is a word) automatically. Ideally, there would also be a way to hook it into our LDAP authentication backend too, though I could probably make this sort of modification if necessary. Since we won't be charging our "client" however, we won't need the ability to generate invoices, handle payments, etc. etc. EDIT: Sample workflow Login authenticated against LDAP Username checked against admin group (not on central LDAP) Click 'new project' and enter project name User created on VPS with project name as username Apache virtual host created and subdomain (using project name) allocated FTP & MySQL users created

  Read the article

• Managing disk in a VM

  - by dst

  I'm replacing my two old rack servers with a new one that has plenty of power to take over the functionality my current servers. The server is a 4U rack mount with 16 3.5" SAS drive bays, two 2.5" bays, a Xeon E3-1230v2 CPU and 32GB of ECC RAM. My issue is the following. I would like to have a FreeBSD file server with ZFS managing disks. However, I need other VMs for e.g. a shell/git server, mail server etc. I'm wondering how to deal with the following issues: I want ZFS to fully manage the disks, so I'm not using any hardware RAID. Should I pass the SAS controller directly to the FreeBSD system as passthrough PCI? I want to maximize the reliability of the setup. On what disks should I install the hypervsor and keep server system disks? For (2) I have the option of having a RAID setup on the SAS controller and using that as system disk to store the hypervisor as well as VM images. However, this makes PCI passthrough to the file server impossible. Another option is using the two 2.5" bays. In terms of reliability how are SSDs compared to e.g. WD RE4 disks? Would it make sense to have two SSDs in software RAID as boot disks for the hypervisor or should I just go with e.g. WD RE4 disks in a software RAID setup. I also need to think about where to store the mails for the mail server, but this could be done over NFS between the VMs. BTW, this is for home use, so the load is not really that big. What I'm looking for is best practices for splitting up a server.

  Read the article

• AD domain on web servers behind NAT - DNS issues?

  - by Ant

  I'm trying to setup an AD domain to manage the security between two Windows Server 2008 webservers that will sooner or later use NLB to balance website requests. I've hit a problem which I think is a simple solution and is down to DNS. My website domain is mydomain.com. The two servers are running behind a NAT firewall on the 10.0.0.0 IP range. I've setup the AD domain to be called ad.mydomain.com (as recommended by MS and a few other answers to questions on here). The second web server however doesn't want to join the domain, and gives an error pinning the problem on DNS - "ensure that the domain name is typed correctly" even though it queries the SRV record successfully and gets the correct DC back - dc.ad.mydomain.com. Doing a dcdiag /test:dns on the DC gives the Delegation error 'DNS Server dc.mydomain.com Missing glue A record'. I have a feeling I need to add something to the public DNS so that it in some way knows about ad.mydomain.com. Can anyone suggest whether I'm on the right track in adding something to the public DNS? Or whether it's something else? Many thanks

  Read the article

• Creating an ec2 image on amazon fails at mkfs.ext3

  - by Dave Orr

  I'm trying to create an image of my ec2 instance in Amazon's cloud. It's been a bit of an adventure so far. I did manage to install Amazon's ec2-api-tools, which was harder than it seemed like it should have been. Then I ran: ec2-bundle-vol -d /mnt -k pk-{key}.pem -c cert-{cert}.pem -u {uid} -s 1536 Which returned: Copying / into the image file /mnt/image... Excluding: /sys/kernel/debug /sys/kernel/security /sys /proc /dev/pts /dev /dev /media /mnt /proc /sys /etc/udev/rules.d/70-persistent-net.rules /etc/udev/rules.d/z25_persistent-net.rules /mnt/image /mnt/img-mnt 1+0 records in 1+0 records out 1048576 bytes (1.0 MB) copied, 0.00677357 s, 155 MB/s mkfs.ext3: option requires an argument -- 'L' Usage: mkfs.ext3 [-c|-l filename] [-b block-size] [-f fragment-size] [-i bytes-per-inode] [-I inode-size] [-J journal-options] [-G meta group size] [-N number-of-inodes] [-m reserved-blocks-percentage] [-o creator-os] [-g blocks-per-group] [-L volume-label] [-M last-mounted-directory] [-O feature[,...]] [-r fs-revision] [-E extended-option[,...]] [-T fs-type] [-U UUID] [-jnqvFKSV] device [blocks-count] ERROR: execution failed: "mkfs.ext3 -F /mnt/image -U 1c001580-9118-4a50-9a25-dcf02be6d25f -L " So mkfs.ext3 wants -L, which is a volume name. But ec2-bundle-vol doesn't seem to take in a volume name as an argument, and the docs (http://docs.amazonwebservices.com/AmazonEC2/gsg/2006-06-26/creating-an-image.html) don't seem to think one should be needed. Certainly their sample command: # ec2-bundle-vol -d /mnt -k ~root/pk-HKZYKTAIG2ECMXYIBH3HXV4ZBZQ55CLO.pem -u 495219933132 -s 1536 doesn't specify anything. So... any help? What am I missing?

  Read the article

• Kickstart: Serve dynamic kickstart images via a CGI or PHP script?

  - by Stefan Lasiewski

  I'd like to kickstart a couple dozen RHEL6/SL6 servers. However, some of these servers are different and I don't want to create a new ks.cfg file for each class of server. Are there any products which can generate a Kickstart file dynamically on the fly, from a template? For example, if I append a line like this to the KERNEL: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi Then the script ks.cgi can determine what host this is (Via the MAC address), and print out Kickstart options which are appropriate for that host. I could optionally override some options by passing parameters to the script, like this: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi?NODETYPE=production&IP=192.168.2.80 After we kickstart the server, we activate Cfengine/Puppet on this system and manage the system using our favorite Configuration Management product. We're experimenting with xCAT but it is proving too cumbersome. I've looked into Cobbler, but I'm not sure it does this. Update: A roll-your-own solution is discussed in the O'Reilly book: Managing RPM-Based Systems with Kickstart and Yum, Chapter 3. Customizing Your Kickstart Install Dynamic ks.cfg, which echos some of the comments in this thread: To implement such a tool is beyond the scope of this Short Cut, but I can walk through the high-level design. Any such solution would mix a data store (the things that change) with a templating solution (the things that don’t change). The data store would hold the per-machine data, such as the IP address and hostname. You would also need a unique identifier, perhaps the hostname, such that you could pick up a given machine’s data. The data store could be a flat file, XML data, or a relational database such as PostgreSQL or MySQL. In turn, to invoke the system, you pass a machine’s unique identifier as a URL parameter. For example: boot: linux ks=http://your.kickstart.server/gen_config?host-server25 In this example, the CGI (or servlet, or whatever) generates a ks.cfg for the machine server25. But where, oh where, is the code for ks.cgi?

  Read the article

• Want to use something like Citrix XenDesktop, Free Alternative?

  - by Chris

  I'm looking to go into IT, general office server management, and it looks like XenDesktop would be a awesome tool to use. If I get it right, you would store a central image of the OS you want to deploy (in an iso file) on the main server. Then use XenDesktop to pull that image down to the client, and it will then boot the OS inside of the virtual machine. Does it download the image of the OS and store it locally (like cloning the VM onto the client?) I'd love to find a free (possibly open source?) alternative to this, I keep on hearing about KVM in Linux and PXE booting a minimalistic OS to use remote KVMs.... Would that be what I'm looking for? Ideally, I'd like a system.. - That allows me to manage one central image for multiple clients (virtualized hardware) - Easily boot a thin client OS that connected to XenDesktop. Would those things be possible with some kind of free alternative? Some guidance would be greatly appreciated.

  Read the article

• Can I get all active directory passwords in clear text using reversible encryption?

  - by christian123

  EDIT: Can anybody actually answer the question? Thanks, I don't need no audit trail, I WILL know all the passwords and users can't change them and I will continue to do so. This is not for hacking! We recently migrated away from a old and rusty Linux/Samba domain to an active directory. We had a custom little interface to manage accounts there. It always stored the passwords of all users and all service accounts in cleartext in a secure location (Of course, many of you will certainly not think of this a being secure, but without real exploits nobody could read that) and disabled password changing on the samba domain controller. In addition, no user can ever select his own passwords, we create them using pwgen. We don't change them every 40 days or so, but only every 2 years to reward employees for really learning them and NOT writing them down. We need the passwords to e.g. go into user accounts and modify settings that are too complicated for group policies or to help users. These might certainly be controversial policies, but I want to continue them on AD. Now I save new accounts and their PWGEN-generated (pwgen creates nice sounding random words with nice amounts of vowels, consonants and numbers) manually into the old text-file that the old scripts used to maintain automatically. How can I get this functionality back in AD? I see that there is "reversible encryption" in AD accounts, probably for challenge response authentication systems that need the cleartext password stored on the server. Is there a script that displays all these passwords? That would be great. (Again: I trust my DC not to be compromised.) Or can I have a plugin into AD users&computers that gets a notification of every new password and stores it into a file? On clients that is possible with GINA-dlls, they can get notified about passwords and get the cleartext.

  Read the article

• How do I secure Sql Server 2008 R2

  - by Mark Tait

  I have both a dedicated and a VPS (from Fasthosts) virtual server - the web sites/applications I run on these, access Sql Server stored on the same web server. Until now, I have logged onto Sql Server on both the deidicated and VPS server, from Sql Server Management Studio - until I noticed in my server application logs, multiple attempts to logon to Sql Server using the 'sa' username, but failed password. So someone/bot is trying hard (repeatedly every couple of hours, for approx 20 attempts during each instance) to log on... so obviously I have to lock down access to Sql Sever remotely. What I have done is gone into Configuration Manager, and in Sql Server Network Configuration - Protocols for Sql2008 and also in Sql Native Client 10.0 Configuration - Client Protocols - I have diabled Named Pipes, TCP/IP (and VIA by default). I have left Shared Memory enabled. I also disabled in Sql Server Services, the Sql Server Browser. Now the only way I can manage the databases on these servers, is by logging on to them via Remote Desktop. Can anyone confirm if this is the correct way of stopping anyone maliciously logging on to Sql Server? (I'm not a DBA or security expert - and there are hundreds of articles advising all different ways - but I was hoping for the experts here to confirm, or otherwise, if what I've done is correct) Thank you, Mark

  Read the article

• Using WebDAV for automated downloads

  - by Geo Ego

  I currently manage a number of sites (at one point about a dozen, currently four, but soon growing into the dozens or hundreds) that serve a piece of software to clients at their remote locations. Our web server is Windows SBS Server 2k3, and the remote servers are Windows Server 2k3.When we have new versions of the software, I upload this new software to a specific directory and rename it; each time the clients boot, they pull their software from that specific directory. With just a few sites, it's no problem for me to RDP in and copy the files over. As the number grows, this will quickly become quite unwieldy. So I'm thinking that WebDAV would be part of a solution, so that I could simply push the newest version to our server (Windows SBS Server 2003) and make it available to the sites to grab. However, on the remote server side, what are some suggestions for automating the download? I only want the servers to download the files during downtime (between 3 AM and 9 AM), and I only want them to download if there is a new version available. I had thought of writing a program that checked the files on the WebDAV server at a regular interval, compared a hash of the current software to a hash of the software on the server, and only downloaded if they were different, but I'm wondering if there is something I am unaware of that can automate the process.

  Read the article

• Centos Server/MySQL server problem

  - by Jake

  Hello all, I currently run a website we get about 15,000-20,000 hits a day. We currently run a very active forum, that is hosted using Vbulletin software. We have 4.5 Million Posts, 80,000 Threads, with about 11,000 members of which just under a third is active all the time. Now I am running a Intel Xeon Quad Core (2.13Ghz) with 4GB of RAM, Centos 5.5 and running DirectAdmin on the box to manage it. I also run the current stable version of Apache, MySQL, and php. This is the only site that is hosted on this machine. Now during random times of day sometimes when it gets busy the server load can get to like 20, but this can also happen when we only have like 200 users active too. I dont understand what is causing these problems. Sometimes I get pages that can generate in .2 seconds other times it takes like 5-8 seconds. I have customized the my.cnf file and that has not helped out anything, I didnt know where else to turn so if anyone has any suggestions please let me know. Thank You In advance.

  Read the article

< Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >