Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 375/740 | < Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >

• PTR Record for host in VLSM subnet

  - by paradroid

  I understand that this is the way a PTR record would be made on a Class A subnet (10.100.250.100 255.0.0.0) dnscmd /RecordAdd 10.in-addr.arpa. 100.250.100 PTR host.domain.tld To clarify the syntax, this is what it should be for a Class C subnet (192.168.1.100 255.255.255.0) dnscmd /RecordAdd 1.168.192.in-addr.arpa. 100 PTR host.domain.tld Is that right? Now how do I do this for a host with the IP address 172.31.111.210 on a 172.31.111.192/26 network? I'm not sure how to do this with a classless subnet mask.

  Read the article

• Kickstart: ifcfg-eth0 file genorated by kickstart when install from network but from initrd when install form USB

  - by dooffas

  When I install Fedora 19 with a kickstart file and via network, the generated ifcfg-eth0 file is genorated by the kickstart: # Generated by parse-kickstart However if I use the same kickstart file and install via a USB stick, the ifcfg file is generated by initrd. # Generated by dracut initrd The line in the kickstart file to set the network settings is as follows: network --device=eth0 --bootproto=dhcp --hostname=SOMEHOSTNAME Is there away to keep network device settings set in the kickstart file when not installing via network?

  Read the article

• "Piping" to MPD

  - by oxinabox.ucc.asn.au

  I would like to "Pipe" the output of my local sound card to MPD on a networked music server. Anyone have any suggestions how to go about this? I'm thinking maybe i can make a live MP3 stream? maybe over the web, or over the intranet? (IIRC MPD supported MP3 streams, i've had Internet radio steams going (though I didn't set them up) I'm not very experienced with MPD, or with webcasts

  Read the article

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• Can't access DD-WRT set in DHCP forwarder

  - by Chris Marisic

  This might sound amazingly stupid but I have a DD-WRT (micro) router that I placed in my network to act as a switch and as a WAP while relying on my cable modem to be the DHCP server. In my attempts to get the configuration right I put the router into DHCP forwarder which then made everything work correctly. The problem is now I can't seem to connect to the router in any fashion to add mac addresses to the WAP access list. Is there something I'm missing or do I need to try a hard reset on it and reconfigure everything?

  Read the article

• Remote Desktop fails after VPN connection.

  - by Samet Sorgut

  The remote computer is connected with Remote Desktop. When the remote computer is connected to VPN the Remote Destop freezes. It is not possible to connect to the remote computer again via Remote Desktop. What can be done to connect to this remote computer after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest?

  Read the article

• something is downloading in background Linux

  - by wisdom

  My laptop boots normally to Linux -LinuxMint- and immediately I like to open gnome-system-monitor but the shock is that something is downloading(the problem has been out 2 days ago) and nothing I run yet ! I did iftop in terminal but nothing strange -a screen shot provided-, also I tried nethogs which showed nothing at all. The more complicated when I reboot and same problem is there so I can't browse/surf Internet, no one connected to my network can browse any more it's absorbing the stream horribly! After many reboots it will go to normal state(no background downloading). But really I can't figure out the problem going behind the scene ! Any suggestion,any help would be appreciated...thanks

  Read the article

• routing traffic between two network cards through firewall

  - by RubyFreak

  I'm trying to test a network device (firewall) using a Linux box, with two network cards, one interface connected to the WAN zone and another interface to LAN zone. The configuration is similar with that |ETH0| <-> | FW | <-> ETH1 So from both interfaces I'm able to ping the respective firewall interface. But i'm not able to fire something like: ping -I eth0 ip.from.eth1 and to get any answer. Is that possible or should the linux network namespace solution or user level tcp stacks (VMs are out of question)

  Read the article

• Setting up a linux server to share an internet connection.

  - by Skizz

  I in the process of reconfiguring my network. It is currently like this: internet - modem - wireless router - wired server/clients | |---- wireless clients but I need to move the router to get a better signal for the wireless clients. So, I'm looking at this: internet - modem - server - switch - wired clients | |---- wireless router - wireless clients How do I set up the server to enable this? Also, what set ups do the clients need. The server is Ubuntu 9.04 and the clients are a mix of Windows XP / 7, Ubuntu and printers. I believe this new set up will allow me to control access to the internet, which would be useful.

  Read the article

• Can't port forward ssh on Asus RT-NU56 wireless router

  - by Matt

  I cannot ssh in (using putty) when I use 10.0.1.31 as the address. database server - wired switch part of Asus wireless router - office LAN So basically, we want to ssh in to the database server from our computer on the wired office LAN. Asus router has an ip of 10.0.1.31 and database server has a static IP of 192.168.0.20 I set up port forwarding like this: ssh 22 192.168.0.20 22 BOTH Firewall is turned completely off. Any other settings I'm missing?

  Read the article

• Connection problems via Wifi (multiple devices)

  - by Kelvin Farrell

  I'm having connection issues with my router (Linksys WRT610N) at home. There are a number of things that are happening (may be more, this is just what I've mainly noticed)... 1) Using my laptop (Macbook Pro OSX Lion), I am unable to complete any operations with my external FTP server, hosted with FatCow. I can connect to it, navigate through all the files, but when I try to edit/delete/add a file the operation times out. EVERY time. I've used two other Wifi connection on my laptop and neither have this issue. 2) I am unable to upload photos/videos to Facebook or Twitter using my phone (Samsung Galaxy S2) or my tablet (HP Touchpad - CM9). Neither am I able to upload files to Dropbox via either of the devices. Same thing happens in all situations; the upload will begin and it will just hang on 0% forever. After about 10 mins I am always forced to disconnect the Wifi to stop the action. 3) My laptop is having slow internet speed, even though we are on 20mb broadband. Speedtests say I'm getting a good connection and my Ping is good, but when using streaming services like Spotify, it takes forever to load a page and frequently stops to buffer whilst playing a song. Don't know if it's worth mentioning but I have no issues with my XBox (Ethernet), AppleTV (Wifi) or my girlfrield's phone (Nokia Lumia 800 - WP7.5) on the network. I'd really appreciate any help. This is driving me insane and is really affecting both my working and leisure use of the internet.

  Read the article

• Can't create a new HomeGroup in Windows 8

  - by Ian Smith

  I'm trying to create a new HomeGroup in Windows 8 for 2 new PCs with Windows 8 installed so that I can share printers etc. Both PCs use Microsoft Account to log in - a Microsoft Account I set up about a year ago with one of the early beta's with a PC that's since been repaved with the RTM of Windows 8 When I click on "HomeGroup" in the "Metro" control panel the "Create" option is not there. Instead I'm told that "HomeGroup" already exists on the PC I've since repaved and renamed and I can join it by entering the password. I have no recollection of what the password might have been and in any event that PC doesn't exist, but there is no way to say "That group doesn't exist anymore just create me a new one dammit". Even using the old Control Panel the "HomeGroup" nonsense persists with the only option being "Join" that needs a password. How do I "start afresh" and create a new HomeGroup that I can use to connect my Windows 8 and Windows 7 PCs and use common printers, network drives etc.

  Read the article

• will heavy network traffic affect other connections on HP ProCurve V1810-48G?

  - by nn4l

  I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

  Read the article

• syslog ip ranges to specific files using `rsyslog`

  - by Mike Pennington

  I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

  Read the article

• On VMWare Server, how can I specify which Ethernet port should be the one to be bridged?

  - by DrDavid

  My server has 4 ethernet ports; 1 uses a APIPA address to connect to a DroboElite (that's how they're designed to work), 1 is connected to the LAN, and the other two are unused currently. The issue is that VMWare Server seems to have an affinity to the port that's connected to the Drobo, which means that it can never reach the internet. If I disable the Drobo port, everything works just fine. If I enable the drobo port, nothing works (well, the drobo works, but the virtual machine doesn't ;) ) How can I tell VMWare Server to NOT use the drobo port when I'm bridging the connection?

  Read the article

• Managing two internet connections in Windows XP, with different applications using different connections

  - by user932867535

  I have two internet connections, one has limited data but is fast, the other has unlimited data but is slow. What am trying to do is assign the unlimited data connection to the application which is downloading a large file, while surfing the net (using Firefox) with the other, faster connection. I tried connecting both connections, but every time I do that, all the applications just jump from the slower connection to the faster one. Is there any way in which I could achieve what I am looking for?

  Read the article

• How can I connect to AS/400 through TN5250?

  - by Swati Sarkar

  How will I find out my iseries server name? I checked through "nslookup" it gives one ip address & I tried to connect TN5250 session to cconnect but could not connect. from dos command line c:\nslookup default server : unknown ip address : 192.168.50.119 Then I tried ping with this IP address - it's giving reply from the above IP address Then I have given this id in TN5250 session, but says can not create a connection to the AS/400.

  Read the article

• Can I ping 127.0.0.1 if my computer isn't connected to a network?

  - by carolyne mumo muia

  Does pinging 127.0.0.1 work on your machine if it's not on the network? Can these two machine be on the same network? machine A (192.168.173.11) machine B (192.168.163.11)

  Read the article

• What would cause different rates of packet loss between client and server in UDP?

  - by febreezey

  If I've implemented a reliable UDP file transfer protocol and I have a file that deliberately drops a percentage of packets when I transmit, why would it be more evident that transmission time increases as the packet loss percentage increases going from the client to server as opposed from the server to the client? Is this something that can be explained as a result of the protocol? Here are my numbers from two separate experiments. I kept the max packet size to 500 Bytes and the opposite direction packet loss to 5% with a 1 Megabyte file: Server to Client loss Percentage varied: 1 MB file, 500 b segments, client to server loss 5% 1% : 17253 ms 3% : 3388 ms 5% : 7252 ms 10% : 6229 ms 11% : 12346 ms 13% : 11282 ms 15% : 9252 ms 20% : 11266 ms Client to Server loss percentage varied 1 MB file, 500 b segments, server to client loss 5% 1%: 4227 ms 3%: 4334 ms 5%: 3308 ms 10%: 31350 ms 11%: 36398 ms 13%: 48436 ms 15%: 65475 ms 20%: 120515 ms You can clearly see an exponential increase in the client to server group

  Read the article

• Understanding tcptraceroute versus http response

  - by kojiro

  I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

  Read the article

• Resolve linux hostname in windows

  - by Martin Giffy D'Souza

  Hi, I have a simple home network with Windows 7 machines and Linux machines (Fedora 12 and 13). I'd like to be able to resolve the Linux machine names from the windows machine. For example: -- Windows 7 ping mylinuxmachine Currently this does not resolve. Any ideas? Thank you, Martin

  Read the article

• Bacula Director and Storage in LAN

  - by B14D3

  I have two networks LAN and DMZ.. Machines in DMZ are accesible from internet ( only over http). In LAN I have servers that see all LAN and all DMZ machines but machinse from DMZ don't see any LAN servers. Machines in LAN have access only to all LAN and DMZ, no direct access to internet and no access from internet. DMZ <------ LAN DMZ ----X--->LAN I'm planning to configure Bacula as major backup system. My plan is to install Bacula Director and Storage deamon on the same server in LAN for safety reasons. So my question is: Will this configuration work, is it posible for bacula director and storage deamon installed on server in LAN to makes backup servers that are in my DMZ? Or in this network configuration Bacula should be in DMZ? (If yes will I can backup with it servers in LAN ?)

  Read the article

• How does IPv4 Subnetting Work?

  - by Kyle Brandt

  This is a Canonical Question about IPv4 Subnets How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. What is classless routing and why is class-based routing obsolete? If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? What is NAT (Network Address Translation).

  Read the article

• LAN speeds and firewall/switch connections

  - by microchasm

  I have a small network with about ten users. All workstations flow into a Dell PowerConnect 3424 which then has a single link to a SonicWALL firewall and from there to a cable modem. More important than internet connectivity is speed between machines (specifically a Windows Server box on the LAN which everyone uses simultaneously). I believe the 3424 has gigabit connections, but they look like they're for stacking. Is there a way to test the speeds on the LAN to see where the speeds are at? Is there any low-hanging fruit insofar as increasing speeds?

  Read the article

• Combine multiple DNS filtering result

  - by Martheen Cahya Paulo

  Several DNS servers provide filtering against different categories, mostly for the local government 'undesirable content', some for malware, and some for ads. What I want is to create/use a DNS server that compare against those filtering DNS servers and only provide the address if all the DNS server agrees. For example if DNS server G provide a clean, unfiltered result, DNS server N provide malware and/or pornography filter, and DNS server F provide ad filter, then G, N and F will only provide the same/similar answer if the query is not categorized as malware, pornography, or advertising. Thus, by creating a server M that only answer if all DNS server agree, M effectively filter against all those categories. Maybe it's possible to do this on DDWRT or Tomato, but if not, I would settle for a solution that can be run in Linux/Windows.

  Read the article

< Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >