Search Results

Search found 12144 results on 486 pages for 'old'.

Page 377/486 | < Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >

  • BIOS not detecting working SATA hard drive

    - by user28927
    Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

    Read the article

  • USB question (how durable is it, how should I workaround this)

    - by Shiki
    The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

    Read the article

  • Why would e-mail from our own domain not be forwarded to gmail

    - by netboffin
    To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

    Read the article

  • Sparc Solaris 2.6 will not boot

    - by joshxdr
    I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

    Read the article

  • BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

    - by DontCare4Free
    I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

    Read the article

  • Dynamic DNS Updates with Wireless and Wired interfaces

    - by Phaedrus
    We have offices full of Windows & Mac users who obtain IP addresses from a Windows DHCP server, which in turn updates Dynamic DNS entries. We are noticing major inconsistencies with the entries, and have found that the problem is occurring more on Macs than on windows, and even more when users are frequently switching from wired to wireless adapter, which makes sense, as this sequence occurs: User enables wired adapter and registers Proper DNS User enables wireless adapter and registers 2nd proper DNS entry user switches off wireless manually and 2nd entry remains improperly until scavenge. Our help desk folks rely heavily (maybe more than they should) on the dynamic entries as part of their business process. For example, the user submits a help desk ticket, and the staff member expects to be able to remote desktop to their machine by hostname, which is hyperlinked in the helpdesk ticketing app. We have implemented multiple solutions & band-aids to different symptoms of the problems such as: Using DNS Reservations for Macintosh PCs Using DNS Scavenging to remove old records Switching from a Cisco DHCP server to the Windows DHCP Server But no matter what we do, it seems impossible to maintain perfect records. Has anyone encountered this problem before? What is industry best practice? Comments & Suggestions are much appreciated, /P

    Read the article

  • Computer Won't Boot Properly, unless in safe mode?

    - by Mr_CryptoPrime
    I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

    Read the article

  • Windows 7 ignores F6/F8 and will not boot

    - by P.Brian.Mackey
    I have a work PC with sophos safeguard encryption on it. Windows failed to start. When I bootup I receive an error saying a recent hardware or software change might be the cause. File: \Boot\BCD Status: 0xc0000098 Info: The windows boot configuration data file does not contain a valid OS entry. This began after the PC forced me to run a system recovery. My machine had powered down improperly (power outage?) and simply would not respond to my keyboard input to cancel the option to scan my system. After the scan "repaired" a boot file, my system crashed. Now it tells me I can insert my windows 7 disk and run recovery. I can't simply do this because of Safeguard. The system recovery can't see my encrypted drive. I tried hitting F2 to manually login to Safeguard and then selected the option to boot from media. The computer prompts me to hit any key to boot from disk...which I do, but once again it is not reading my keyboard input. I can't get F8/F6 to bypass startup files and get me to a command prompt like the old days. If I could get to a command prompt I might could recover the file windows jacked up from its backup location...though I may need to use the windows recovery disk UI to do this..??? In the past I've been able to slap in a PS/2 keyboard when the USB keyboards stop responding like this. I have no PS/2 keyboard available. Anyone have any idea how I can undo the damage windows system recovery has done with safeguard installed?

    Read the article

  • Generic/Text Printer on Windows 7 not prompting for file name

    - by Trevor Tippins
    Hope someone can shed some light on this. I am downloading reports from an AIX-based system by directing them to a TT printer which the terminal emulator (MultiView 2000) intercepts and directs to the default printer on the local system. This local printer is configured as a vanilla Generic/Text printer attached to a FILE port. When I print from AIX, the output is spooled down and the local printer prompts for a file name into which to save the file...but not under Windows 7. This has worked fine for many years, on both Win2K and WinXP. However, on Windows 7 the output gets spooled as a file into spool\PRINTERS (and looks as expected) but the print job then hangs with a status of "Error - Printing" and never prompts for a file name. I have to cancel the job. The Generic/Text printer works as expected with other applications. I have tried setting the printer to print directly rather than spooling but this only serves to hang the terminal session too. I've also tried to run the emulator in Windows 2000 Compatibility Mode and as Administrator in case it was something like that but with no luck. As you might expect, it does work fine in XP Mode (as long as I print to a printer defined therein and not the host's printer) but operationally this isn't going to be an option. Obviously this emulation software is a decade old (at least) and I could just cross/upgrade all the users (at a cost) but, before I do so, has anyone seen this sort of behaviour before and found some sort of fix? Remote OS: AIX 5 Client OS: Windows 7 Pro (32-bit) Printer: Generic/Text on a FILE port TE Software: MultiView 2000 (32-bit) Thanks in advance.

    Read the article

  • In a Shell scripts, check version of installed package, make a decision based on output

    - by DJDarkViper
    Looking to write a cross distro / cross version shell script that makes sure a forced version of PHP is installed Example: Ubuntu 12.04 has 5.3, Ubuntu 13.10 has 5.5, Debian 7 has 5.4 I need this script, when run on a distro that has an old version of PHP, to update the repo to point to a package for 5.4, and if the distro has too new of a version, can downgrade to 5.4 appropriately. Im still not entirely comprehensive of Shell/Terminals technical limit of what you can do with it, but ill be perfectly frank that im still not totally used to existing tools The best I can think at the moment is: php -v | grep "PHP 5" but that returns a bunch of potentially changeable granular characters (PHP 5.4.4-14+deb7u5 (cli) (built: Oct 3 2013 09:24:58) ). Im not sure what to pipe to after this to extract out the characters im interested in Im not sure if im being totally clear, im not sure how to ask this.. Basically, in an automated shell script for Linux distros, how do I extract the PHP version (and just the PHP version number preferably) and make a decision based on that output EDIT This line ended up doing pretty dang good php -v | grep "PHP 5" | sed 's/.*PHP \([^-]*\).*/\1/' | cut -c 1-3 Bit long in the tooth, but gives me "5.3", "5.4", and "5.5" which is exactly what I need to work with

    Read the article

  • Redirecting a single request to another pages, ignoring www subdomain

    - by Petter Brodin
    I have a site running on IIS 7.5 that does an automatic redirect from 'http://mysite.com/whatever.aspx' to 'http://www.mysite.com/whatever.aspx' On the site, there is a lot of traffic to an old URL that I want to redirect to the front page, index.aspx: 'http://mysite.com/foo/bar/index.cgi%something=asdf&somethingelse=qwerty' The problem is that no matter what I try, I can only get the redirect to work with the www subdomain. If I use the URL without www, I just end up at 'http://www.mysite.com/404.aspx' Any ideas? Thanks in advance for all help! Edit3: it seems like the browser caching the redirect response was messing with me, so edit2 is wrong. See my response below. Edit2: disregard edit1, it doesn't seem like it's working after all. Edit: here's some further info: using this article I've managed to redirect from 'http://mysite.com/foo/bar/index.cgi' to 'http://www.mysite.com/index.aspx', but if I add the query string parameters, it still redirects to 'http://www.mysite.com/404.aspx' Isn't there a way to catch all requests to the cgi file, including query string parameters?

    Read the article

  • Intermittently uncommunicative subnets

    - by mhd
    Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

    Read the article

  • LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

    - by CityView
    On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

    Read the article

  • why does the partition start on sector 2048 instead of 63

    - by gcb
    I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

    Read the article

  • Strange sound behavior

    - by caarlos0
    First of all, sorry for the tittle. English isn't my native language, and I can't find a word to describe the strange behavior I'm getting here. In the most simple explanation, is like sound keeps going down and up again... Think in a kid with that old radios that have a circled volume button. Think like these kid keeps "turning" the volume button. That is the behavior I'm getting here. At first, I believed that it was a pulseaudio issue, but, it isn't. I followed the wiki part I think that should be my problem, but it didn't work. After that, as I'm using XFCE, I didn't really need pulseaudio, so I removed it and stays with a clean alsa, hopping that will fix my problem. Sweet mistake. It really looks like a kid looking for trouble. I believed it worked, and, suddenly, here is the same issue again. BTW: I have a full-upgraded testing system (yeah, I upgraded to testing hopping for new pulseaudio version which fix the issue), no pulseaudio at all, just xfce, started with startxfce. What can I do to fix this? It's extremely annoying... sometimes I just want to throw my laptop in the wall because of this. Any extra info you need, please, tell me. Thanks in advance -- EDIT: My alsamixer is like this: And here is a video with the sound behavior.

    Read the article

  • "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

    - by salparadise
    I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

    Read the article

  • How do I share a complete XP disk so it can be seen from a Windows 7 system? (To move all files to a

    - by Ian Ringrose
    This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it) The XP machine runs XP home and hence has "simple file shairing" turn on. So it seems that even if I create a admin account (with password) and connect with that account, it still comes in as "guest" on the XP machine. Chooseing to share the folder I want access to rather then the top of the disk drive seems to work, but is a pain as I need to share each user's folder with a different share name. If the new computer was not a laptop, I would just plug the hard disk from the old machine into it, but being a laptop I don't have that option.

    Read the article

  • Recover data from Dynamic Disk (MBR) bigger than 2TB

    - by Helder
    Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

    Read the article

  • Logitech Performance MX Mouse Jumps on OS X Lion (10.7.4)

    - by Adam Thompson
    I have a Logitech MX Revolution wireless mouse that I am trying to use with OS X Lion. Everything is working except for one problem... there is a small, but quite noticeable, jump when the mouse cursor is moved. The problem is mostly prevalent when dragging and dropping files or trying to highlight items. It makes performing any task with the mouse accurately next to impossible. I did quite a bit of looking and found that all kinds of people have had mouse issues with OS X. I've tried all of the following with absolutely no success: Using the official drivers from Logitech (these performed worse than the default mouse drivers in OS X) Using SteerMouse as a third party mouse driver. This worked ever so slightly better than the default driver, but still suffered quite frequently from the skipping problem Cleaning the sensor on the mouse and ensuring it's not the result of the surface that it's being used on. Tested the mouse on a Windows machine. The mouse worked absolutely flawlessly on the other machine. Changed the channel that my wireless router operates on by the off chance my problems were the result of interference. This also had no effect. I can't think of anything else that could possibly interfere with the mouse. I'm am out of ideas on what to try, so I would really appreciate if anyone has any suggestions. I should also mention that an old wired mouse I had laying around worked just fine when I plugged it in. This really isn't the best solution, however, as I really prefer the MX Revolution.

    Read the article

  • Need to restore emails that Outlook deleted from the mail server

    - by Mugen
    I wanted to use POP mail for my Yahoo mail account. So I went to the Yahoo mail settings and enabled POP feature. I installed Microsoft Outlook 2007 and added the settings for my Yahoo mail account. Then I performed a sync. I successfully received all the emails from Yahoo account into my pc. But when I logged into my Yahoo mail online, to my horror all the mails were deleted. It seems someone in Microsoft for some reason decided to keep the default setting unchecked for "Leave copy of messages on the server". This has been a very old account and I need to have all the mails also present on the mail server so I can access it anytime and future purposes. Is there anyway I can restore these emails on the server again? Any ideas how I can get it back to the way it was? I have been googling this for quite sometime now but I'm not able to find it. Any helpful suggestions are welcome. Thanks.

    Read the article

  • Remove directory from URL IIS 7.5

    - by xalx
    I've tried to find a solution to this and found some guides out there but none seem to work. I have the following URL - http://www.mysite.com/aboutus.html However there are some other sites which link to my old hosted site and point to http://www.mysite.com/nw/aboutus.html. My issue here is trying to remove the 'nw' directory from the URL's. I have setup the following URL Rewrite in IIS but it does not seem to do anything, <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <rewrite> <rules> <rule name="Redirect all to root folder" enabled="true" stopProcessing="true"> <match url="^nw$|^/nw/(.*)$" /> <conditions> </conditions> <action type="Redirect" url="nw/{R:1}" /> </rule> <rule name="RewriteToFile"> <match url="^(?!nw/)(.*)" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Any insight would be appreciated.

    Read the article

  • How can I get Pinch to Zoom back in Desktop mode?

    - by Ben Brocka
    Windows 7 had an old implimentation of Pinch to Zoom where bringing your fingers apart/together would act similar to ctrl + +/-, the standard zoom. It's not as nice as granular zoom (like iOS/Android use) but it worked. Most notably it doesn't work in Chrome (did before) but I haven't noticed it working in any other apps. In windows 8 desktop mode, pinch to zoom doesn't seem to work at all. It doesn't even work in One Note 2010, which, if I recall correctly, had granular zoom in Windows 7. I have an (older) 2 touch point multi-touch monitor, and I can see the visual feedback that the two touch points and coming closer/farther apart, but it doesn't zoom. Note I'm using the touchscreen, not a touchpad or the Arch mouse or other peripherals. Can I enable this somehow or is it gone from Desktop mode? It works fine in Metro apps. Additionally I get weird visual feedback when placing my second finger on the screen; a shrinking transparent square appears somewhere between the two fingers, visually similar to the Right Click visual queue when long-pressing. It's not a right click though, I can't tell what, if anything, it's doing.

    Read the article

  • What's the best way to clone multiple PCs from one machine?

    - by Jason T.
    Where I work we have dozens and dozens of old ThinkPad laptops. A lot of these can be reused but not for our needs. They have been long since replaced. The higher-ups have decided to donate them to charity. For better or for worse I have been tasked with reimaging them. I took a laptop and installed the factory copy of Windows, updated it, configured it appropriately. Now I'm trying to reimage it to dozens of other laptops. What's some good software to do this? First I used clonezilla to clone the hdd in the laptop to an internal drive in an external enclosure and it worked. Then I tried taking the base image out and connecting it externally to a laptop that needed to be imaged and I got it to work a few times. So far so good, right? Well once I informed my boss of my findings and what I would want to do then the images started to not work on new laptops. One of three things would happen: The Thinkpads would just blink at me and Windows wouldn't load. Or Windows would load but freeze within two minutes. Last but not least the laptops would BSOD during the Windows XP bootup. These laptops are not going to be used by the company. They're going to charity. So can anyone else recommend a way to reimage multiple laptops?

    Read the article

  • Windows 7 Startup fails after installation

    - by Nadav S.
    I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

    Read the article

  • Set up Linux box as WAP for MyBookLive?

    - by AcidFlask
    I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

    Read the article

< Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >