Search Results

Search found 12437 results on 498 pages for 'normal mapping'.

Page 382/498 | < Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >

• Why does my computer crash randomly?

  - by Donavon Decker

  The other day I went out to my van to get my Tower and when I opened the trunk it fell out. I brought it into the house and opened it, and everything looked ok. When I started it up, about 1-3 minutes afterwards it would crash. It did this over and over until I reseated the cooler. Everything seemed normal again, until after about 10 minutes of gameplay (any game), it would crash. I reseated my GPU + reinstalled the drivers, however I still get the same error. A while back, I'd check my 'Windows Rating' periodically, and all of them were in the '6.0-6.9' range except for my hard disk usage (always been like that [not relative]). Today I went in and looked, and my Processor and Memory was rated 5.4. I reseated my cpu and my memory, refreshed the windows rating, and then my processor and memory went from 5.4, to 5.1. A few minutes ago I reseated them once again, and now it's back to 5.4. Note: Not sure if this is relevant to the issue, but I updated my bios earlier today I honestly have no idea what the issue is, but I'm getting aggravated at the problem. Here are some images which contain images of my specifications: i1271.photobucket.com/albums/jj623/donxdeck/1_zps09f0607c.jpg i1271.photobucket.com/albums/jj623/donxdeck/4_zps381cd00a.jpg i1271.photobucket.com/albums/jj623/donxdeck/3_zps54bba720.jpg i1271.photobucket.com/albums/jj623/donxdeck/2_zps945d3d72.jpg Thanks for the help

  Read the article

• NVidia ION and /dev/mapper/nvidia_... issues.

  - by Ritsaert Hornstra

  I have an NVidia ION board with 4 SATA ports and want to use that to run a Linux Server (CentOS 5.4). I first hooed up 3 HDs (that will be a RAID5 array) and a forth small boot HD. I first started to use the onboard RAID capability but that does not work correctly under Linux: the raid capacity is not a real RAID but uses lvm to define some arays. After setting the BIOS back to normal SATA mode and whiping the HDs, the first boot harddisk (/dev/sda) is seen as /dev/sda BEFORE mounting and after mounting as /dev/mapper/nvidia_. CentOS is unable to install on it (and grub is not installable on it either). So somehow the harddisk is still seen as if it belongs to some lvm volume. I tried to clean out the HD by issuing a few dd if=/dev/zero of=/dev/sda commands to wipe the starting cylinders and final cylinders but to no avail. Did anyone see this problem and did anyone find a solution? UPDATE When I create only a single ext3 partition on the first HD (/dev/mapper/nvidia_...) no LVM partitions are seen and I can boot from /dev/mapper/nvidia_.... Now the next step is to see how I can get rid of this folly.

  Read the article

• DIY NAS - links for Instructions

  - by Kaushik Gopal

  Good folk of SU, I'm planning to build a NAS (Network Access Storage). I'm planning to do it cheap (:read Old PC Config + Open source software). I was looking for good DIY links . Before you shoot this down as a Repost, I'm only looking for good links containing detailed instructions for setting up a NAS. I did a fair bit of searching and found these links (so please suggest others. While these links are great they delve more on the hardware side, i'm looking for more instructions in the software side). For the sake of the interwebs: Ubuntu: http://snarfquest.com/wiki/index.php/Setting_up_a_Home_NAS http://www.smallnetbuilder.com/content/view/27962/77/ http://jonpeck.blogspot.com/2006/11/how-to-configure-80-fileserver-in-45.html FreeNAS http://www.smallbusinesscomputing.com/webmaster/article.php/3719706 http://www.codeproject.com/KB/system/homemade_nas.aspxhttp://www.codeproject.com/KB/system/homemade_nas.aspx There was one at rubbervir.us that everyone points to, but apparently the site has gone down. A couple of other queries: Is Printer/Scanner sharing a possibility with NAS devices? Many talk of torrent support with NAS Devices, a little more light on this? Does this mean, an auto download of torrent through a feed into NAS, or just support for storing Torrent download files onto the NAS(don't see the difference between the latter and a normal file tranfer)

  Read the article

• ClearType setting ignored in Windows Virtual PC with Windows XP Pro

  - by Yadyn

  I have a VM set up through Windows Virtual PC for Windows XP Pro and I have been completely unable to get ClearType to work. I have turned it on in the Display - Appearance - Effects dialog but it seems like it completely ignores this. All text is still without any anti-aliasing. Even setting it to normal smoothing doesn't work. If I disable Integration Features, it seems to work, but then I lose a lot of nice features. What's weirder, is that the Windows XP Mode installed with Windows Virtual PC (this is separate from my XP Pro VM) works with both ClearType and Integration Features just fine. I turned it on the same way and it works like a charm, no problems. I'm running Windows 7 Professional 64-bit as the host OS and have the latest (to my knowledge) Windows Virtual PC installed. The only funny business I can think of is that I've enabled 24-bit color via the Group Policy setting inside each XP virtual machine (both Pro and the stripped down XP mode copy). This is a fairly well-known trick documented all over the web, but here's a typical post about it.

  Read the article

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• laptop motherboard "shorts" when connected to adapter

  - by Bash

  Disclaimer: I'm sort of a noob, and this is a long post. Thank you all in advance! summary: completely dead laptop with no signs of life whatsoever (suddenly, for no apparent reason) Here's the deal: Lenovo Y470 (only a few months old with no water or shock damage). It stopped working suddenly (no lights, no sound, even when connecting adapter with or without battery). I tried a different adapter (same electrical rating), but no luck. I disassembled the thing completely, and tried plugging in the adapter and looking for signs of life with all different combinations of components installed (tried all combinations of RAM, CPU, USB power cords, screen, etc plugged in). no luck. Then, I noticed (as I was plugging in the adapter to try for the millionth time) that there was a "spark" for an instant when I first connect the adapter to the power jack. The adapter's LED would then flash (indicating it isn't working or charging). So, I thought the power jack has a short of some sort (due to bad soldering or something). Scanned virtually every single component on the motherboard, and tested the power jack connections with a multimeter. No shorts or damage to anything on the entire motherboard. Now I'm thinking I need to replace the motherboard. But, my actual question: What does this "shorting" when connecting the adapter signify? (btw, the voltage across the power connections and current through it drop to virtually zero when the adapter is connected and "sparks", and they stay that way). The bewildering thing is that there are no damaged components, and the voltage across adapter terminals returns to normal after I disconnect it (so it's not damaged). Please take a look at the pictures (of the motherboard's power connection and nearby components) and see if I'm missing something completely obvious... Links to pictures and laptop and motherboard model: pictures on DropBox Motherboard model: LA-6881P Laptop model: Lenovo IdeaPad Y470

  Read the article

• SSH dynamic port forwarding, "Connection refused"

  - by crodjer

  I am trying to do dynamic portforwarding using openssh through a remote computer following this command: ssh -D 6789 rohan@<remote_ip> -p <remote_port> This should set up a socks server on my comp as I assume. I am able to use this for normal browsing but can't connect to IRC or remote ssh (through proxychains). I get this error: channel 3: open failed: connect failed: Connection refused A high verbosity level output of the error: $ debug1: Connection to port 6789 forwarding to socks port 0 requested. debug2: fd 9 setting TCP_NODELAY debug2: fd 9 setting O_NONBLOCK debug3: fd 9 is O_NONBLOCK debug1: channel 3: new [dynamic-tcpip] debug2: channel 3: pre_dynamic: have 0 debug2: channel 3: pre_dynamic: have 4 debug2: channel 3: decode socks5 debug2: channel 3: socks5 auth done debug2: channel 3: pre_dynamic: need more debug2: channel 3: pre_dynamic: have 0 debug2: channel 3: pre_dynamic: have 10 debug2: channel 3: decode socks5 debug2: channel 3: socks5 post auth debug2: channel 3: dynamic request: socks5 host 4.2.2.2 port 53 command 1 debug3: Wrote 96 bytes for a total of 3335 channel 3: open failed: connect failed: Connection refused debug2: channel 3: zombie debug2: channel 3: garbage collecting debug1: channel 3: free: direct-tcpip: listening port 6789 for 4.2.2.2 port 53, connect from 127.0.0.1 port 33694, nchannels 4 debug3: channel 3: status: The following connections are open: #2 client-session (t4 r0 i0/0 o0/0 fd 6/7 cfd -1) debug3: channel 3: close_fds r 9 w 9 e -1 c -1 I googled for this too, but couldn't find any solutions.

  Read the article

• Whats the difference between local and remote addresses in 2008 firewall address

  - by Ian

  In the firewall advanced security manager/Inbound rules/rule property/scope tab you have two sections to specify local ip addresses and remote ip addresses. What makes an address qualify as a local or remote address and what difference does it make? This question is pretty obvious with a normal setup, but now that I'm setting up a remote virtualized server I'm not quite sure. What I've got is a physical host with two interfaces. The physical host uses interface 1 with a public IP. The virtualized machine is connected interface 2 with a public ip. I have a virtual subnet between the two - 192.168.123.0 When editing the firewall rule, if I place 192.168.123.0/24 in the local ip address area or remote ip address area what does windows do differently? Does it do anything differently? The reason I ask this is that I'm having problems getting the domain communication working between the two with the firewall active. I have plenty of experience with firewalls so I know what I want to do, but the logic of what is going on here escapes me and these rules are tedious to have to edit one by one. Ian

  Read the article

• Finding a backup and synchronization solution

  - by Andrea Zilio

  I'm having difficulties to find a backup and synchronization solution with the following characteristics: Cross-platform: Windows, Linux, Mac Offsite backup (so Internet Backup) Data deduplication Transfer only new/modified bits of modified files Secure: Data encrypted before leaving computer Maintain multiple versions of files (even deleted files) Folder synchronization integrated with backup and across multiple computers connected to the internet (not necessarily in the same LAN) I think that the Folder Sync feature needs a better explanation. The use case is this: you have a desktop pc and a laptop. The desktop pc contains a folder with some files and this folder is part of the backup (so it was selected to be backed up). The laptop does not contain that folder or that files at all. Then you're abroad with your laptop and you need that folder. So you want to be able to open the backup program, select that folder from the backup and download it in your laptop mantaining it synchronized with the backed up version. When you then come back home and switch on your desktop pc you want the folder we're talking about to be updated in the desktop PC. Does anyone knows any service with all these features? I've only found SpiderOak to support all the features I've mentioned but I'm not completely satisfied by the time taken to complete a backup. Sometimes it seems to hang for minutes with no reasons at all and folder synchronization occurs only after all files are backed up (instead folder sync should have a separated queue independent from other backup operations and synchronization should occurs frequently... for example every 5 minutes or less, independently from the frequency of normal backup operations)

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Hi, Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• How to collect the performance data of a server during an unreachable/down period using Nagios?

  - by gsc-frank

  Some time services and host stop responding due to a poor server performance. I mean, if for some reason (could be lot of concurrency services access, a expensive backup execution on the server or whatever that consume tons of server resources) a server performance is very degraded, that could lead that the server isn't capable to establish any "normal network communication" (without trigger whatever standards timeouts defined for such communication). Knowing host's performance data (cpu, memory, ...) in case of available during that period (host is not down and despite of its performance degradation still allow plugins collect performance data) could be very useful for sysadmin to try to determine what cause the problem, or at least, if the host performance was good and don't interfered at all in the host/service down. This problem could be solved using remote active (NRPE) or remote passive (NSCA) if such remote solutions could store (buffered) perf data to be send to central Nagios server when host performance or network outage allow it. I read the doc of both solutions and can't find any reference to such buffer mechanism neither what happened in case that NSCA can't reach Nagios server. Any idea of how solve this lack of info? so useful for forensic analysis. EDIT: My questions isn about which tools I can use to debug perf problems or gather perf data to analysis, but is about how collect (using Nagios) host perf data even during a network outage for its posterior analysis (kind of forensic analysis). The idea is integrate such data to Nagios graphers like pnp4nagios and NagiosGrapther. I know that I could install tools like Cacti in each of my host, and have a kind of performance data collection redundancy, but I really want avoid that and try to solve all perf analysis requirements with one tools: Nagios

  Read the article

• Troubleshooting certificate issues

  - by Weezy

  I'm trying to access my (European Parliament) Webmail from a Linux/Firefox machine at the following address and I get security warning messages explaining that the identity of the site cannot be verified (the error message is in french). But this only happens with Linux/Firefox from one machine. Here's the address: https://webmail.europarl.europa.eu/ (and I'm trying to access it from my home, not from the EP). And here's the detailed error message: webmail.europarl.europa.eu utilise un certificat de sécurité invalide. Le certificat n'est pas sûr car l'autorité délivrant le certificat est inconnue. (Code d'erreur : sec_error_unknown_issuer) So basically, if I translate, it is telling that the webmail.europarl.europa.eu certificate is invalid because the authority that delivered the certificate is unknown. I do only get this invalid certificate thing on Linux/Firefox. From a MacBookPro running Safari, I go to what looks like the correct webmail login page. From the same Linux machine, but using another user account and Chrome instead of Firefox, I go to what looks like the correct webmail login page. So there are several possibilities, here are a few ones: Firefox is right and my Linux box has been hacked Firefox is right and detecting something that neither Chrome nor Safari is detecting (like, say, my router that may be hacked) Safari on the MacBook Pro and Chrome on Linux are both correct and it is just Firefox on Linux that is wrongly stressing me when everything is normal. How do I know which one of these possibilities (or any other) is correct? How can I troubleshoot what is going on with either Linux/Firefox or with the parliament's webmail?

  Read the article

• SQL Server 2008 cluster freezing

  - by Ed Leighton-Dick

  We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

  Read the article

• Configuring suExec to work with Apache and PHP via FastCGI

  - by RandomPsychology

  I have installed ISPConfig 3 on an Ubuntu VPS and configured it for Apache + PHP via FastCGI and suexec. I am able to upload PHP apps (e.g. Wordpress) and run them normally w/ suexec. However, for some reason the PHP scripts cannot write data to disk. For instance, trying to upgrade a plugin via Wordpress' web interface causes it to fail with the error "Could not create directory /path/to/wp-content/upgrade/plugin.tmp." Trying to upload media and other assets also fails via the web. I've checked owner/group on the directory structure and it looks good. The suExec log also seems to be normal and I don't see any indicative errors in the web server logs. I can also confirm that changing the owner/group on the directories does result in the expected error in suexec.log. Additionally, I have the directory permissions set to u=rw,g=r,o= and I've also tried setting g=rw. None of this results in my scripts being able to write to the directories. What am I doing wrong?

  Read the article

• How to repair Mac OSX without reinstalling?

  - by RahulVyas

  I have an intel PC. I have installed iDeneb Mac OS X in my pc. It's running fine. After that I thought to install Snow Leopard for running the iPad SDK. So I bought a retail Snow Leopard and boot it with Rebel EFI boot loader. When I was installing Snow Leopard, at the end of installation, setup gives an error. So I restarted my PC and boot with Rebel and I saw that mac was there so I boot that into safe mode and Mac OSX runs. After that I install iPad SDK. But when I try to create an application, XCode is not responsive. It hangs when I choose new project, give it a name and save it on disk. After just as I gave name and choose save it hangs. Is there any way i can repair my Mac OSX without reinstalling? I have also unable to boot into normal mode and also without Rebel CD. So I want to boot without Rebel CD and also want to run iPad SDK so please help me to solve this problem.

  Read the article

• Symbolic directory link shared in domain

  - by Sabre

  We have a file server that is 2008R2 STD, it is a member server in a 2008 AD. I need to relocate some of the files and directories and would like to do it behind the scenes more or less without impacting the users. (Reason for this is that some of the files, due to recent software changes, HAVE to be located locally on one of the workstations, but they can be accessed by other applications remotely.) So symbolic links seem the panacea here, I moved a directory to another network share in the same domain (Windows 7 professional), created a symlink to it in the location it used to be in, named it the same thing, and to the local user it seems almost transparent. I.E. When logged into the desktop of the file server, I can go to the directory, open the link, it leaps to the other share as if it were local, exactly what would be expected. Then I tried it from another client computer (Windows 7 professional as well), went through the normal provisioning of R2R and L2R with fsutil... No joy. What I am getting is an access denied "Logon failure: Unknown username or bad password." using the same account that I log on locally to the file server with (Which happens to be the domain admin) So I cannot believe it is telling the truth, or... I assume it is not passing the credentials I am connecting to the first share all the way through the symlink. The end result is I want users on the domain to browser to share A, inside share A is a mixture of directories/files that reside there, and symlinks to directories/files on the second machine over the network in the same domain. Possible? Or am I misunderstanding how the symlink should work?

  Read the article

• CouchDB crashes at startup when path to config file has space(s)

  - by Barry Wark

  I'm hoping to run CouchDB as a per-user Launch Agent on OS X. I'm using the coucdbx-core folder from the CouchDB Server.app as the base of my CouchDB deployment. I'd like each user to have their own couch instance (on a different port), necessitating separate config files for each instance. The logical place to put these files is in ~/Library/Application Support/ for each user. I can put the entire distribution in ~/Library/Application Support/my-app/coucdbx, and put the .ini at ~/Library/Application Support/my-app/local.ini. Starting couchdb as bin/couchdb -a ../local.ini (from ~/Library/Application Support/my-app/coucdbx) works great. But I'd like to save every user the ~50MB couchdbx and install the couchdbx-core in a shared location (e.g. within my app's .app bundle). When I do this, the path to the per-user config file contains a space, and I get the following error when starting CouchDB: $ bin/couchdb -n -a ~/Library/Application\ Support/us.physion.ovation/default.ini {"init terminating in do_boot",{{badmatch,{error,{bad_return,{{couch_app,start,[normal,["/Users/hs/prj/build-couchdb/build/etc/couchdb/default.ini","/Users/hs/prj/build-couchdb/build/etc/couchdb/local.ini"]]},{'EXIT',{{badmatch,{error,{error,enoent}}},[{couch_server_sup,start_server,1,[{file,"/Users/hs/prj/build-couchdb/dependencies/couchdb/src/couchdb/couch_server_sup.erl"},{line,56}]},{application_master,start_it_old,4,[{file,"application_master.erl"},{line,274}]}]}}}}}},[{couch,start,0,[{file,"/Users/hs/prj/build-couchdb/dependencies/couchdb/src/couchdb/couch.erl"},{line,18}]},{init,start_it,1,[]},{init,start_em,1,[]}]}} Is there any way to provide a config file at the command line, if that config file's path includes space(s)? Despite my best efforts in the mailing list archives, wiki and google, I haven't been able to find a solution or a definitive "it can't work". Any help greatly appreciated.

  Read the article

• Server 2008 R2 DNS Lockup / Stops Resolving Internet Names

  - by Richard Maynard

  We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed

  Read the article

• Windows Server 2008R2 Virtual Lab Activation strategies?

  - by William Hilsum

  I have a ESXi server that I use for testing, however, I am often needing to create additional Windows Server virtual machines. Typically, if I do not need a VM for more than 30 days, I simply do not activate. However, I have been doing a lot of HA/DRS testing recently and I have had a few servers up for more than this time. I have a MSDN account with Microsoft and have already received extra keys for Windows Server 2008 R2. I am doing nothing illegal and I am sure if I asked, they would issue more - but, I do not want to tempt fate! I have got 3 different "activated" windows snapshots I can get to at any time. If I try to clone these machines, I get the usual "did you copy or move them VM" message. If I choose copy, as far as I can see, it changes the BIOS ID and NIC MACs which is enough to disable activation. If I choose move, it keeps the activation fine (obviously, I know to change the NIC MAC - I believe I can leave the BIOS ID without problems). However, either of these options keeps the same SID code for the computer and user accounts. After the activation period has expired, as far as I can see, all that happens is optional updates do not work - it seems that the normal updates work fine. Based on this, as you can easily get in to Windows when not activated without any sort of workaround, I was wondering if it is ok just to leave a machine un activated? (However, I obviously would prefer if it was activated!) Alternatively, how dangerous is it run multiple machines on a non domain environment with the same SID? I am just interested to know if anyone can recommend a strategy for me? I have only found one solution that deals with bypassing activation - I am not interested in doing anything remotely dodgy... at a stretch, I am happy to rearm (I have never needed to keep a server past 100 days), but, I would rather have a proper strategy in place.

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Eclipse grinds to a halt when building workspace

  - by Chris Thompson

  Hi all, This is a bit of a vague question because, frankly, I don't even know where to begin diagnosing the issue. My eclipse (Galileo) installation grinds to a complete halt when it's building the workspace -- to the point where I can't even type. I know the Android SDK I have installed is a major culprit because I can watch the memory usage go through the roof (through the built-in heap monitor) when the Android SDK content loader starts up. Every time I save a file though, the program just stops. The message at the bottom of the screen says Building workspace (74%) and sits there for about 30 or so seconds before completing and returning the performance to normal. I have a few other plugins installed (Maven, SVN, etc) but I'm assuming the main issue is Android. Has anybody had similar issues or any luck correcting this sort of problem? If there's anymore information you think would be helpful, just let me know...I didn't want to do a core dump on this question... I'm running it on Windows 7 64-bit for what it's worth. Thanks! Chris

  Read the article

• DFSR NTFS Permissions Not Working!??!

  - by megadood

  I have two windwos 2008 standard servers running DFSR okay. I can create a file on one server, it is replicated to the other okay etc. I have the namespace shared folder on each server shared with full control administrators / everyone change/read permissions. I then browse to the folder on server 1 e.g.\server1\namespace\share\folder1. I right click the folder, and configure the NTFS permissions as I would like for example Adminsitrators Full Control / One User Read/Write Access / No other users in the user list. I save this and then double check the second server e.g. \server2\namespace\share\folder1. I right click the same folder name as before and can see the NTFS permissions have replicated accordingly. I right click the folder and go to properties - security - advanced - effective permissions and select a user that shouldnt be able to get into that folder e.g. testuser. It agrees with the NTFS permissions and shows that testuser has no ticks next to any permissions so should be denied access. I logon to any network PC or the server as testuser. Browse to \server1\namespace\share\folder1. It lets me straight in, no access denied messages. The same applies to server2. It seems as thought all my NTFS permissions are being ignored. I have 1 DFS share and then all the subfolders are a mixture of private folders and public folders so need the NTFS permissions to work ideally. Any idea whats going on? Is this normal? From my tests all users can access any DFSR folder under the namespace\share which is quite worrying. Thanks

  Read the article

• System Idle Process network traffic?-Updated

  - by Moab

  I was using NetBalancer and noticed network traffic on an unidentified service, but when I highlight it and then go to the lower center pane and click the parent process it says it is the System Idle process, it is showing incoming and outgoing traffic in the upper pane, anyone know why this Windows System Idle Process is talking on the network? Windows 7 HP 64bit . . . Edit, after blocking the traffic for that unidentified Service I checked my event viewer (Windows LogsSystem) and found 3 new events that were never recorded before and matched the time I blocked the traffic. So is this part of the Windows local DNS cache? Event ID 1014 DNS Client Events Name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded. dns.msftncsi.com Name resolution for the name wpad.home timed out after none of the configured DNS servers responded. wpad Name resolution for the name mscrl.microsoft.com timed out after none of the configured DNS servers responded. mscrl.microsoft.com . Then My Web Browser refused to work, I re-enabled the traffic and all returned to normal. .

  Read the article

• Mountain Lion overheating issue have to do with launchd/Python?

  - by Christopher Jones

  So, Ever since I installed ML, my MacBook Air has been running SUPER hot. Opened up activity monitor, and everything seemed to be pretty normal, until I had it refresh every .5 seconds... and then I started seeing some interesting things. A 'Python' process appears and is terminated several times a second, and uses TONS of CPU 70-110. It's parent process is 'launchd' - and when I sample the process, there is a lot going on with Python. http://db.tt/ovuX3hZM These appear and disappear too quickly to get one... this one only happened to be using 70 ish percent of CPU... but they consistently hit 100-110%. http://db.tt/ovuX3hZMg The parent process... launchd. lots of context switches and UNIX system calls... What is the deal here? (photo goes here when I earn the street cred) The sample of launchd. ANY help here could be of help to not only me, but possibly many others experiencing decreased battery life and warmer laps these days because of this Mountain Lion weirdness. PLEASE HELP! PS - I'd put the screen grabs inline, but i don't have enough street cred yet.

  Read the article

< Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >