Search Results

Search found 15605 results on 625 pages for 'exchange cached mode'.

Page 389/625 | < Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >

• What's constitute an entry on the IPTables and how to find out which client it is originated from

  - by cbd

  I have a Billion BiPac 7700N Modem/Router/Access Point and I connect another router (TP-Link TL-WR1043ND) in wan-bypass mode to extend the wireless coverage. Lately, I noticed that the connection through TP-Link has been dropping out quite regularly. Having read some posts on the Internet, I checked system log on 7700N and found that there are many "nf_conntract: expectation table full" errors, which I suppose the iptables are full. My questions: What does constitute an entry on the iptable? Is it a client or a connection (which means one client can have multiple connections) How could I find out where are those connections originated from? Note: Many reported that the issue is usually related to having torrents running but I don't have any torrents running. Thank you.

  Read the article

• Is the motherboard the cause of these errors?

  - by ianfuture

  Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

  Read the article

• Groups issue on Ubuntu

  - by grobarTN

  Hello, I am member of couple of groups lets say Master, Student, Web. The problem is that by default whatever I do is first created under student group. I need to set it so it is created with Web group. Folder www/ where I need to write file is already mode 770. But because it picks up my student group it does not allow me to write to that folder. Is there any way to change the group that I create files under. If I execute groups it lists all groups so I am member of correct group I just cant write to the folder. Anyone?

  Read the article

• How to force a resolution in linux?

  - by hi

  I have a HP LP3065 that requires a dual link dvi cable to go up to 2560x1600 resolution. However, I do not have that cable, but I want to use 1920x1200 resolution. However, my nVidia Display Settings (also system display settings) will only go up to 1280x1024, which looks horribly pixelated on the 30". How do I force the 1920x1200 resolution? I tried adding the mode into my xorg.conf file, but it still would not take it. I know my vid card can do 1920x1200 since it works on the 24" monitor with the same dvi cable. Here are my specs: Fedora 12 Nvidia Quadro NVS 420 Intel Xenon E5530 cpu 6gig memory Thanks

  Read the article

• Issues running java in Solaris 9 container

  - by Matthew Watson

  Hi, I have a solaris 9 container built from a physical server using flarcreate. Everything seems fine, except when trying to trying to run any "java -server" process it fails with the following error This is on a Sunfire T1000 machine running Solaris 10 10/09 s10s_u8wos_08a SPARC Running jdk1.5.0_15 Exception java.lang.OutOfMemoryError: requested -4 bytes for size_t in /BUILD_AREA/jdk1.5.0_15/hotspot/src/os/solaris/vm/os_solaris.cpp. Out of swap space? As far as I can tell I'm not actually out of swap space. Running java in client mode works without a problem. Googles only suggestion is related to x86. Any suggestions? Thanks.

  Read the article

• Triple Monitor Stand Recommendations

  - by Josh W.

  I've got two Acer X233Hbid 23" Widescreen LCD Monitors from new egg back last summer, each weigh 10.5lbs a piece I Want to Buy a third Acer 23" (closest I've found is the X235 on Newegg, weighs in at 11.5 lbs) , one of the new ATI video cards that will output to 3 displays, and then a monitor stand that will let me use them in portrait mode like the image below. I found the following: $260 - ERGOTRON 33-323-200 DS100 Triple-Monitor Desk Stand and was wondering if anyone has any experience with this kind of setup and whether it would work for me or not.. Thanks!

  Read the article

• HP Pavillion dm3 (Windows 7) BSOD,

  - by Lee

  HI I have a HP Pavilion dm3. It came up with a BSOD and then didn't give me an option to start up in safe mode. I dont have any cd drive, nor did it come with a Windows cd anyway. I presume that it has a partition in my laptop for that kinda stuff. I was hoping to boot it using a usb but I don't know how to do it or where to download the stuff from. I have access to network computers, so am able to download from the internet but it's not a Windows7 computer. I am able to download from the computers that I have access to, but unable to run any executable files on them. Can someone please help? Thanks in advance

  Read the article

• Umbraco on Windows 7 64-bit

  - by HeavyWave

  I'm trying to install Umbraco CMS on Windows 7 64-bit and I get the following exception: [HttpException (0x80004005): Could not load file or assembly 'ImageManipulation, Version=1.0.2105.41209, Culture=neutral, PublicKeyToken=null' or one of its dependencies. Failed to grant minimum permission required. The application pool's trust mode is set to 'Full', all the user permissions are just as on other sites hosted on the same machine. I went through all relevant topics on Umbraco's forum, but all advices are about the trust level. How do I fix this?

  Read the article

• Call issue with Freeswitch

  - by gbraad

  I am testing the following with Freeswitch and different devices (nokia n900, nokia e60, ekiga) and have similar results between them. On the Freeswitch server (1.0.4 in multi-tenant mode) I have several user profiles for a domain, e.g. 1000, 1001 for host.com The user are authenticated correctly and calls can be placede. When I place a call from a device registered as [email protected] to [email protected] it will show up at the other end (1002) as [email protected] I would expect this call to show up as [email protected]. The IP address is the one of from the Freeswitch server. Because of this, the calls are no correctly recognized by the address book on certain devices. Can the he domain FQDN of the callers domain/acount be used, instead of the IP address of the server in the SIP uri?

  Read the article

• Kindle 2 and PDFs in landscape

  - by doronkatz

  Hi guys, I am looking at getting a Kindle 2, read a lot about the PDF support (or lack off) and wanted to ask someone who has a kindle, a question. If you read a pdf in landscape mode, does it shrink the text to have it all in the one screen, or does it increase font size and split it into two or more pages. I have another reader, the iRiver Story and it does that, splits it into multiple pages thus making it readable. I know you can't zoom or anything like that in portrait view (i assume) I know you will say stick with iRiver, but the make of the kindle is a lot better (metallic back) and its useful to have a hybrid amazon book/pdf reader in one.

  Read the article

• Linux Bluetooth [closed]

  - by Chris

  Not sure if this is the proper forum; please forgive me if it's not... I have a Lenovo S10 'netbook' that I've installed Fedora 17 ("LXDE spin") on. So far pretty much everything works great, except, the on-board Bluetooth. lsusb shows the controller present (0a5c:2101 Broadcom Corp. Bluetooth Controller), hcitool dev shows hci0 present, but when I put my mouse ("Lenovo Bluetooth Laser Mouse," which works perfectly paired with a MacBook Pro, MacBook Air, Mac mini, and Lenovo SL500 (with a USB dongle; running Windows 7)) into pairing mode and run either hcitool scan (reports "Scanning ..." and, without further information or error message, returns to the shell prompt) or bluetooth-wizard (from the gnome-bluetooth package) and try to detect the mouse, I get nothing... Frustrating! Thanks anyone who can point me in the right direction!

  Read the article

• What linux permissions are need for www?

  - by Xeoncross

  I know that 777 is full read/write/execute permission for owner/group/other. So this doesn't seem to be needed as it leaves random users full permissions. What permissions are need to be used on /var/www so that... Source control like git or svn Normal users in a group like "websites" or added to "www-data" Servers like apache or lighthttpd And PHP/Perl/Ruby can all read, create, and run files there? If I'm correct, Ruby and PHP scripts are not "executed" directly - but passed to an interpreter. So there is no need for execute permission on files in /var/www. Therefore, it seems like the correct permission would be chmod -R 1660 which would make all files shareable by these four entities all files non-executable by mistake block everyone else from the directory entirely set the permission mode to "sticky" for all future files Is this correct? Update: I just realized that files and directories might need different permissions - I was talking about files above so i'm not sure what the directory permissions would need to be.

  Read the article

• mdadm raid5 recover double disk failure - with a twist (drive order)

  - by Peter Bos

  Let me acknowledge first off that I have made mistakes, and that I have a backup for most but not all of the data on this RAID. I still have hope of recovering the rest of the data. I don't have the kind of money to take the drives to a recovery expert company. Mistake #0, not having a 100% backup. I know. I have a mdadm RAID5 system of 4x3TB. Drives /dev/sd[b-e], all with one partition /dev/sd[b-e]1. I'm aware that RAID5 on very large drives is risky, yet I did it anyway. Recent events The RAID become degraded after a two drive failure. One drive [/dev/sdc] is really gone, the other [/dev/sde] came back up after a power cycle, but was not automatically re-added to the RAID. So I was left with a 4 device RAID with only 2 active drives [/dev/sdb and /dev/sdd]. Mistake #1, not using dd copies of the drives for restoring the RAID. I did not have the drives or the time. Mistake #2, not making a backup of the superblock and mdadm -E of the remaining drives. Recovery attempt I reassembled the RAID in degraded mode with mdadm --assemble --force /dev/md0, using /dev/sd[bde]1. I could then access my data. I replaced /dev/sdc with a spare; empty; identical drive. I removed the old /dev/sdc1 from the RAID mdadm --fail /dev/md0 /dev/sdc1 Mistake #3, not doing this before replacing the drive I then partitioned the new /dev/sdc and added it to the RAID. mdadm --add /dev/md0 /dev/sdc1 It then began to restore the RAID. ETA 300 mins. I followed the process via /proc/mdstat to 2% and then went to do other stuff. Checking the result Several hours (but less then 300 mins) later, I checked the process. It had stopped due to a read error on /dev/sde1. Here is where the trouble really starts I then removed /dev/sde1 from the RAID and re-added it. I can't remember why I did this; it was late. mdadm --manage /dev/md0 --remove /dev/sde1 mdadm --manage /dev/md0 --add /dev/sde1 However, /dev/sde1 was now marked as spare. So I decided to recreate the whole array using --assume-clean using what I thought was the right order, and with /dev/sdc1 missing. mdadm --create /dev/md0 --assume-clean -l5 -n4 /dev/sdb1 missing /dev/sdd1 /dev/sde1 That worked, but the filesystem was not recognized while trying to mount. (It should have been EXT4). Device order I then checked a recent backup I had of /proc/mdstat, and I found the drive order. md0 : active raid5 sdb1[0] sde1[4] sdd1[2] sdc1[1] 8790402048 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] I then remembered this RAID had suffered a drive loss about a year ago, and recovered from it by replacing the faulty drive with a spare one. That may have scrambled the device order a bit...so there was no drive [3] but only [0],[1],[2], and [4]. I tried to find the drive order with the Permute_array script: https://raid.wiki.kernel.org/index.php/Permute_array.pl but that did not find the right order. Questions I now have two main questions: I screwed up all the superblocks on the drives, but only gave: mdadm --create --assume-clean commands (so I should not have overwritten the data itself on /dev/sd[bde]1. Am I right that in theory the RAID can be restored [assuming for a moment that /dev/sde1 is ok] if I just find the right device order? Is it important that /dev/sde1 be given the device number [4] in the RAID? When I create it with mdadm --create /dev/md0 --assume-clean -l5 -n4 \ /dev/sdb1 missing /dev/sdd1 /dev/sde1 it is assigned the number [3]. I wonder if that is relevant to the calculation of the parity blocks. If it turns out to be important, how can I recreate the array with /dev/sdb1[0] missing[1] /dev/sdd1[2] /dev/sde1[4]? If I could get that to work I could start it in degraded mode and add the new drive /dev/sdc1 and let it resync again. It's OK if you would like to point out to me that this may not have been the best course of action, but you'll find that I realized this. It would be great if anyone has any suggestions.

  Read the article

• TightVNC grey screen?

  - by gary

  I'm trying to help my mom remotely with some PC problems. She's not too computer savvy, so to keep the firewall stuff on my side of things, I tried to use a reverse VNC connection: On my machine, I set up TightVNC client in listening mode. I also opened TCP port 5500 on my router and firewall, and checked it using http://canyouseeme.org/. On her machine, I (instructed her to) set up TightVNC server, and connect to my machine's IP ('Add New Client...'). Both machines run Windows XP & TightVNC 1.3.10. The problem: When she tries to connect, a TightVNC window with grey background pops up on my machine, but I never get to see the remote desktop. It just remains grey. However, it seems that I control the mouse on the remote side (she says it's moving). I tried to reverse-connect from another machine on my LAN and it works without a problem. Any idea what the problem could be?

  Read the article

• Setting up D-link AP2100 as a repeater

  - by Mersan

  Hi, I have two D-Link AP2100, one is connected to a switch (with cable). The second one I would like to use as a repeater, using the WiFi connection to the first and not connected to the switch. Does anyone know first if this is possible, and second and most important, how does one do it. I have tested to set the second AP in repeater-mode, and it is connected to the first, I have full strength to the second one, but I'm not receiving any IP från the DHCP-server, so no access out. Any ideas? /Mersan

  Read the article

• Firewall blocks FTP PASV response

  - by harper

  0 down vote favorite I have an FTP server that supports passive server mode (using PASV command). This works fine with Windows XP. When I want to access this server from Windows Vista or Windows 7 with firewall enabled I experience a immediate connection shutdown. A reset packet is sent to the server, the socket is signaled that the server had reset the connection (what is not true). The problem disappears when the firewall is disabled. Connections to other FTP servers work correctly. The difference is that the servers response to PASV does not enclose the address field with parentheses. This is legal as documented in RFC-959 and RFC-1132. How can I configure the firewall to stop this bad behavior?

  Read the article

• Why is Apple System Image Utility so slow?

  - by Jon Rhoades

  I'm using Apple System Image Utility (SIU) on Snow Leopard 10.6.2 and I am rather disturbed it takes over Three hours to make a Netrestore or Netboot image. I'm using as the donor machine a brand new iMac and as the imaging machine a brand new iMac connected using target disk mode & Firewire 800. The hard drive size and subsequent image is about 8GB. To restore the image over the network takes about 4 minutes. Given that Norton Ghost will take an image in about 5 minutes (or less on newer machines) over USB2, why is the Mac over an order of magnitude slower?

  Read the article

• How to diagnose repeated freezing of windows 7 (comes back alive in few seconds)

  - by Akash Kava

  I installed Windows 7 in a 3 year old machine, it installed successfully, took all drivers and running great, but what happens is every 5-6 minutes it freezes for few seconds... 30 seconds to 1 minute and then comes back alive. I checked Event Viewer, nothing matching the frozen timeline. I would appriciate any help on how to detect causing service/hardware. After it comes alive, everything runs normal, I did run task manager and checked cpu usage, at time it freezes just before and after that no task took more cpu or memory, it was like idle machine. No external usb drives or no devices, on board intel desktop board with SATA HDD, SATA hdd running in absolute good mode.

  Read the article

• What solutions do I have to enforce memory limit on PHP server?

  - by Zulgrib

  I would like to enforce memory limit on a folder basis (and have it applied on subfolders) but I don't want the user able to change the memory limit. I know I can disable ini_set and I know I can enforce a hard limit or deny ini_set with Suhosin. With the first one, I doubt it will block changing it from the user.ini file, for the second, the user may still be able to change it to the hard limit I enforce with Suhosin. In both cases, I would prefer to not entierly block ini_set because it may have a legit use for other settings. In case it is important, I'm using PHP version 5.4.4 with nginx (PHP in FPM mode)

  Read the article

• My saved drafts become unread email in Windows Live Mail and Gmail IMAP

  - by Valamas

  I have setup windows live mail with my gmail account in IMAP mode. When I draft an email and save it. It saves in the drafts automatically. Within a minute, my WLM sound alerts new mail and shows mail icon in the system tray. However, this is for the draft I have saved which appears unread. To make the mail notification icon go away in the system tray, I go off and mark the draft as read. This repetition is tedious and distracting. How can I avoid this annoyance? thanks

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

• IOGEAR KVM cannot reset admin account

  - by George Horlacher

  According to the manual you can do a cold reset by holding the reset button in for 3 seconds. This does seem to reset it but the username and password are not reset... I've tried the keyboard hotkeys - Num-Lock and minus sign (-) to get into hotkey mode and then use the "r" and "" to reset to factory defaults but that doesnt seem to do anything either. It just reverts to User1. I'm not sure what the default admin username should be but admin doesnt seem to work I need to get to the admin menu to name the ports but cannot get access. Any ideas? Using GCS1758 manual with no luck.

  Read the article

• Linux Logitech QuickCam Pro 9000 - microphone issues

  - by drahnr

  I got a Logitech Quickcam Pro 9000, the cam itself is working as it honors the UVC spec. This fancy WebCam has a integrated mic which worked some time before but now, it does no more. (Note: I use pulseaudio as it is a USB Mic and I am not really keen on the hassle of ALSA setup) Things I check already are if it gets detected at all: $ lsusb |grep Logi Bus 002 Device 002: ID 046d:0809 Logitech, Inc. Webcam Pro 9000 is muted in alsa-mixer - not the case, volume at 100 pavucontrol shows it too, but no input level bar! On top of that, if I open the gnome3 (fallback mode) audio panel(from the desktop panel), and disabel/reenable it in the hardware tab, it works "for some time"... Any hints? Any ideas? I am really out options for now, and the fact it worked like 6 months ago (perfectly) makes it no better.

  Read the article

• Understanding Asterisk Server features

  - by Arham Ali Qureshi

  I need to ask few question about Asterisk 1) Does ACL mean by Access Control list here ?If yes than how could i use it? >ip show user 6001 * Name : 6001 Secret : <Set> MD5Secret : <Not set> Context : DLPN_Admin Language : AMA flags : Unknown Transfer mode: open MaxCallBR : 384 kbps CallingPres : Presentation Allowed, Not Screened Call limit : 2147483647 Callgroup : 1 Pickupgroup : 1 Callerid : "test" <6001> ACL : No Sess-Timers : Accept Sess-Refresh : uas Sess-Expires : 1800 secs Sess-Min-SE : 90 secs RTP Engine : asterisk Codec Order : (ulaw:20,gsm:20) Auto-Framing: No 2) What is mean by "Require Call Token" in Asterisk Digium GIU on Create new User Panel 3) Is There any command from where i can get users VOICE MAIL password ? 4) What AMI or CLI command set call recording on or off for user ? and if i want that file to be stored on client computer not on server memory what could i do ?

  Read the article

• Disable pendrive blinking in Linux

  - by Joey Adams

  I recently bought a 16GB Super Talent pen drive that seems to work well for running the Ubuntu Live "CD" in persistent mode (see this for how I installed it). One slightly annoying thing, however, is that this pen drive has a bright red light on it that stays on when it's idle. Is there a way to make the light stay off at least when the pen drive is not performing IO? I'm not even sure it's possible to do. If there is (in Linux), I'm guessing it boils down to some ioctl invoked by some utility. Otherwise, I imagine it would involve hacking the firmware or simply opening up the pen drive and removing the LED :D Then again, I guess it keeps the LED on to indicate that the drive should not be removed.

  Read the article

< Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >