Search Results

Search found 1811 results on 73 pages for 'virtualization'.

Page 39/73 | < Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >

• Is it possible/advisable to run VMware Server ESX/ESXi on a laptop?

  - by cletus

  The idea of having a small footprint hypervisor as the primary OS on a laptop or desktop where every "real" OS is a guest appeals to me. Now I realize this software is more typically used on blades and the other servers but can it be done on a normal PC? Should it be? What requirements are there (eg hardware/BIOS/chipset)? Is there a performance impact for doing so? Is it a good/bad idea?

  Read the article

• ubuntu's average load never below "0.00 0.01 0.05"

  - by Karma Fusebox

  I have several ubuntu 12.04 VMs running on a ubuntu 12.04 KVM host. Those of the virtual machines that are totally idle with no services (except syslog and the other "small" standard stuff of a fresh installation) show a constant load of "0.00 0.01 0.05" in top/htop as average 1/5/15. When there are "real" applications running, the load averages behave perfectly normal but they never fall below the mentioned values. While this doesn't affect performance at all and could easily be ignored, it screws up the monitoring graphs in a very annoying way: (Notice how load15 behaves nicely if 0.05 for a short time in the right half of the pic) Unfortunately I don't know what diagnostic outputs might be helpful for you, so here's some default stuff: # top top - 16:31:01 up 1:05, 1 user, load average: 0.00, 0.01, 0.05 Tasks: 62 total, 1 running, 61 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.2%sy, 0.0%ni, 99.2%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1019464k total, 73452k used, 946012k free, 6140k buffers Swap: 0k total, 0k used, 0k free, 22504k cached . # free -m total used free shared buffers cached Mem: 995 72 923 0 6 21 -/+ buffers/cache: 43 951 Swap: 0 0 0 . # iostat -x /dev/vda Linux 3.2.0-32-virtual (vm3) 11/15/2012 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 0.25 0.00 0.65 0.20 0.24 98.66 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util vda 0.14 0.12 0.51 0.22 6.74 1.46 22.50 0.02 23.26 20.64 29.30 7.63 0.56 Need something else? Has anyone ever seen this behavior? Might this be a bug in kvm/ubuntu/kernel 3.x in the end? Thanks a lot!

  Read the article

• running 2 or more med-v Workspaces simultaneously

  - by Goryachkin Alexandr

  mdop 2010; med-v Workspace UI configured in Full desktop mode. first Workspace starts fine second med-v launch couse message asking to stop first Workspace. is it possibe to run 2 med-v Workspaces simultaneously on one med-v client?

  Read the article

• Running Microsoft Office Communication Server 2007 R2 on virtual machine?

  - by Espo

  Does anyone know if it is officially supported to run Microsoft Office Communication Server 2007 R2 on a virtual machine? (Virtual PC/VMWare/Hyper-V)

  Read the article

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do. Thanks!

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Making a bootable image of linux Red Hat Ent Es for a VM

  - by djshortbus

  I have a old server running Red Hat that has some valuable apps installed. I would like to create a bootable image of the drive and install it in a VM on a newer server. i am trying to avoid reinstalling Red Hat the apps and data. Any useful links or advice would be greatly appreciated.(Not yet decided on the VM Software)

  Read the article

• How do I know if my Xeon Processor supports hardware virtualisation?

  - by gshankar

  I've been scouring the net (mainly the wikipaedia lists and intel's site. I even pulled out the datasheet for my processor) but I can't seem to answer this question. Does my Xeon support hardware virtualisation? The processor in question is a: "Nocona" (standard-voltage, 90 nm) 2800MHz. Other details can be found here: http://en.wikipedia.org/wiki/List_of_Intel_Xeon_microprocessors#.22Nocona.22_.28standard-voltage.2C_90_nm.29 I'm pretty sure the answer is no as it's a pretty old server but I can't find a single place which has a definitive yes/no answer so I'm still looking...

  Read the article

• How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

  - by penx

  I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

  Read the article

• Network Block Device (NBD) clients for Windows or similar solutions

  - by przemoc

  Are there any NBD clients for Windows? Strangely, I cannot find any, or I am searching for them in a wrong way. Such client should be possibly a driver with front-end tool (may be a command-line one) allowing to create virtual drives and associate them with given hosts (or simply localhost) and ports where NBD servers are listening. From user perspective virtual drive should be close to what physical drive is, so it should be accessible as something like \\.\PhysicalDriveX (maybe \\.\VirtualDriveX?), be visible in Disk Management (diskmgmt.msc) and mountvol tools at least. (The only thing I found remotely close to NBD on Windows is ImDisk's proxy mode and companion tool devio, but AFAIK ImDisk only works at partition level (so no virtual drive) and devio uses different protocol.) Secondary question is: Are there any (preferably simple) Windows-specific solutions allowing creation of virtual drive delegating read/write request to user-space via some explicit way (like via TCP, IPC, DLL implementing given API, etc.)?

  Read the article

• One bigger Virtual Machine distributed across many Nodes [on hold]

  - by flyer

  I just setup virtual machines on one hardware with Vagrant (this is just a test environment, not production!). I want to use a Puppet to configure them and next try to setup OpenStack. I am not sure If I am understanding how this should look at the end. Is it possible to have below architecture with OpenStack after all where I will run one Virtual Machine with Linux? ------------------------------- | VM | ------------------------------- | NOVA | NOVA | NOVA | ------------------------------- | OpenStack | ------------------------------- | Node | Node | Node | ------------------------------- (In my environment Nodes are just virtual machines, but my question concerns separate Hardware nodes) After some comments... Is it a language barrier, or? This is only my 'virtual environment'. If we imagine this virtual machines are a separate Nodes (e.g. every has 4 cores) the OpenStack is still the same, right? Can I run one Virtual Machine across many Nodes with OpenStack? Is it possible to aggregate the computation power of separate machines in one virtual distributed operating system?

  Read the article

• vSphere education - What are the downsides of configuring virtual machines with *too* much RAM?

  - by ewwhite

  VMware memory management seems to be a tricky balancing act. With cluster RAM, Resource Pools, VMware's management techniques (TPS, ballooning, host swapping), in-guest RAM utilization, swapping, reservations, shares and limits, there are a lot of variables. I'm in a situation where clients are using dedicated vSphere cluster resources. However, they are configuring the virtual machines as though they were on physical hardware. In turn, this means a standard VM build may have 4 vCPUs and 16GB or more of RAM. I come from the school of starting small (1 vCPU, minimal RAM), checking real-world use and adjusting up as necessary. Some examples from a "problem" cluster. Resource pool summary - Looks almost 4:1 overcommitted. Note the high amount of ballooned RAM. Resource allocation - The Worst Case Allocation column shows that these VMs would have access to less than 50% of their configured RAM under constrained conditions. The real-time memory utilization graph of the top VM in the listing above. 4 vCPU and 64GB RAM allocated. It averages under 9GB use. Summary of the same VM What are the downsides of overcommitting and overconfiguring resources (specifically RAM) in vSphere environments? Assuming that the VMs can run in less RAM, is it fair to say that there's overhead to configuring virtual machines with more RAM than they need? What is the counter-argument to: "if a VM has 16GB of RAM allocated, but only uses 4GB, what's the problem??"? E.g. do customers need to be educated? What specific metric should be used to meter RAM usage. Tracking the peaks of "Active" versus time?

  Read the article

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• IT merger - self-sufficient site with domain controller VS thin clients outpost with access to termi

  - by imagodei

  SITUATION: A larger company acquires a smaller one. IT infrastructure has to be merged. There are no immediate plans to change the current size or role of the smaller company - the offices and production remain. It has a Win 2003 SBS domain server, Win 2000 file server, linux server for SVN and internal Wikipedia, 2 or 3 production machines, LTO backup solution. The servers are approx. 5 years old. Cisco network equippment (switches, wireless, ASA). Mail solution is a hosted Exchange. There are approx. 35 desktops and laptops in the company. IT infrastructure unification: There are 2 IT merging proposals. 1.) Replacing old servers, installing Win Server 2008 domain controller, and setting up either subdomain or domain trust to a larger company. File server and other servers remain local and synchronization should be set up to a centralized location in larger company. Similary with the backup - it remains local and if needed it should be replicated to a centralized location. Licensing is managed by smaller company. 2.) All servers are moved to a centralized location in larger company. As many desktop machines as possible are replaced by thin clients. The actual machines are virtualized and hosted by Terminal server at the same central location. Citrix solutions will be used. Only router and site-2-site VPN connection remain at the smaller company. Backup internet line to insure near 100% availability is needed. Licensing is mainly managed by larger company. Only specialized software for PCs that will not be virtualized is managed by smaller company. I'd like to ask you to discuss both solutions a bit. In your opinion, which is better from the operational point of view? Which is more reliable, cheaper in the long run? Easier to manage from the system administrator's point of view? Easier on the budget and easier to maintain from IT department's point of view? Does anybody have any experience with the second option and how does it perform in production environment? Pros and cons of both? Your input will be of great significance to me. Thank you very much!

  Read the article

• Starting VMs with an executable with as low overhead as possible

  - by Robert Koritnik

  Is there a solution to create a virtual machine and start it by having an executable file, that will start the machine? If possible to start as quickly as possible. Strange situation? Not at all. Read on... Real life scenario Since we can't have domain controller on a non-server OS it would be nice to have domain controller in an as thin as possible machine (possibly Samba or similar because we'd like to make it startup as quickly as possible - in a matter of a few seconds) packed in a single executable. We could then configure our non-server OS to run the executable when it starts and before user logs in. This would make it possible to login into a domain.

  Read the article

• Why is connecting to external FTP sites slow on virtual 2008 R2 and not on host?

  - by subkamran

  I have Windows Server 2008 R2 installed as a virtual guest in my Windows 7 host via VirtualBox 4.0. I did this to move my development activity to a controlled environment that doesn't affect my host OS when I don't want to develop. The problem I have is that when I try to connect to my shared hosting FTP, it's slow as hell on the virtual OS but perfectly fast on the host. I tried: Disabling Windows Firewall Trying several different FTP clients Anyone else have this issue?

  Read the article

• xm console command is not working in XEN

  - by stillStudent

  I have XEN 4.0.x.x rpm with CENT OS. I have set it up and have many VMs on it. But problem is when I execute 'xm console ' command from dom0, command just hangs dom0 and some 'y' comes up in next line but nothing really happens. Is it a bug in xen 4.0 and I need to upgrade it or I can tweak some configuration file in /etc/xen/ to make it work. I found following at some site but its not working: In order to be able to login to your domU from the console using: xm create {your hostname}.cfg -c (to the set root password for ssh, for instance, or to see more output than just kernel output when debugging) it may be necessary to add the following line to your /etc/xen/{your hostname}.cfg extra='xencons=tty' Is there any other way to solve it?

  Read the article

• Xen find VBD id for physical disks

  - by Joe

  I'm starting a xen domU using xm create config.cfg. Within the config file are a number of physical block devices (LVs) which are added to the guest and can be accessed fine when it boots. However, at a point in the future I need to be able to hot unplug one of these disks using the xm block-detach command. This command, however, requires the vbd id of the device to be detached and I can't find a way to find the device id for a particular disk 'plugged in' at start up. Any help is much appreciated!

  Read the article

• How do you synchronise huge sparse files (VM disk images) between machines?

  - by chrisdew

  Is there a command, such as rsync, which can synchronise huge, sparse, files from one linux server to another? It is very important that the destination file remains sparse. It may be longer (but not bigger) than the drive which contains it. Only changed blocks should be sent across the wire. I have tried rsync, but got no joy. groups.google.com/group/mailing.unix.rsync/browse_thread/thread/94f39271980513d3 If I write a programme to do this, am I just reinventing the wheel? http://www.finalcog.com/synchronise-block-devices Thanks, Chris.

  Read the article

• VPN server on Windows Server 2008 for a small office

  - by cmbrnt

  I'm going to refurbish the IT-infrastructure for a small organization with one single office, and I'm not sure what VPN server to use. In your opinion, would the built-in Windows Server 2008 VPN server suffice or are there any specific problems with it as opposed to, for example, OpenVPN? I'd rather run a Windows native VPN server, but if there are few (preferably free) good alternatives, I could install VMware ESXi and virtualize both Windows and an OpenVPN-server. By the way, because of a low budget this office runs a solution with only one physical server. Any advice would be great to help me grasp this field of which I'm quite a novice. Thank you!

  Read the article

• Combine several physical servers into 1 virtual server

  - by Jayaraman

  The current virtualisation splits one big physical server into smaller virtual servers. But is it possible to combine several physical servers into 1 virtual server ?

  Read the article

• POC of take screenshot from XP virtual machine of windows 7 main machine.

  - by Svisstack

  Hello, I searching any ideas of take screenshot of main machine on windows 7 from virtual machine on windows XP, have any ideas or proof on concept to can do this? Maybe from integration drivers or something? I don't require any code snipets, must have only POC of can't do this. EDIT: Can be process integration idea? (dump any process memory on main machine from virtualized)

  Read the article

• VMware ESXi: how to choose between VMI Paravirtualization and 64-bit?

  - by netvope

  VMware ESXi 4 supports VMI paravirtualization for 32-bit OS but not for 64-bit OS. For performance consideration, is it better to use a 32-bit Ubuntu Server guest without paravirtualization or a 64-bit one with VMI paravirtualization? Hardware: Core 2 Quad, 8 GB RAM Workload: Software development/testing, webserver, database

  Read the article

• Windows 7 Virtual PC + Linux Ubuntu

  - by Daniel Henry

  I've installed Ubuntu inside a virtual machine running on Windows 7's Virtual PC. One thing I've noticed right away is that it has to capture the mouse and not all the hardware works as expected. I didn't have such problems in my virtual Windows XP. Is there anything I need to do to either Virtual PC or within Ubuntu that will get them to cooperate as well as Windows XP seems to?

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

< Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >