Search Results

Search found 11313 results on 453 pages for 'ip aliasing'.

Page 392/453 | < Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399  | Next Page >

• Specific DNS sometimes resolves to wildcard, incorrectly

  - by Mojo

  I have an intermittent problem, and I'm not sure where to start trying to troubleshoot it. In our dev environment, we have two visible IP addresses on load balancers, one to the front-end, and one to a number of back-end service machines. The front-end is configured to take a wildcard DNS name to support generic "portals." dev.example.com A 10.1.1.1 *.dev.example.com CNAME dev.example.com The back-end servers are all specific names within the same space: core.dev.example.com A 10.1.1.2 cms.dev.example.com CNAME core.dev.example.com search.dev.example.com CNAME core.dev.example.com Here's the problem. Periodically a developer or a program trying to reach, say, cms.dev.example.com will get a result that points to the front-end, instead of the back-end load balancer: cms.dev.example.com is an alias to core.dev.example.com core.dev.example.com is an alias to dev.example.com (WRONG!) dev.example.com 10.1.1.1 The developers are all on Mac OS X machines, though I've seen the problem occur on an Ubuntu machine as well, using a local cloud host DNS resolver. Sometimes the developer is using a VPN, which directs the DNS to its own resolver, and sometimes he's on the local net using a DNS resolver assigned by the NAT router. Sometimes clearing the Mac OS X DNS cache, logging into the VPN, then logging out of the VPN, will make the problem go away. The origin authoritative server is on zerigo, and a dig directly to their name servers always seems to give the correct answer. The published DNS cache time for these records is 15 minutes, but the problem has been intermittent for about a week. Any troubleshooting suggestions?

  Read the article

• Error setting up Blackberry Internet Service with Outlook Web Access

  - by Travis

  I'm trying to set up Blackberry Internet Service to connect to our Windows SBS2003 outlook web access. I've tried every possible combination of credentials by I always get the same error: An error occured during email account validation. Please check your information and try again. If the error persists please contact your System Administrator. The fields are the following: Outlook Web Access URL: http://mail.domain.com/exchange (I've also tried just using the IP address http://000.000.000.000/exchange with no effect). User Name: JohnDoe (same as OWA login / domain username - I've also tried DOMAIN\JohnDoe) Email Address: [email protected] Mailbox Name: This one confused me a little bit, but it seems it should be the same as the domain username (eg. JohnDoe). I've also tried DOMAIN\JohnDoe, and a number of other things. No matter what I do, I get the same error message. At this point, I'm basically just trying things, because I don't really know how this service is supposed to work. Does anyone know what causes this particularly vague error message, and what I can change either in my email settings or on our exchange server to resolve this?

  Read the article

• Windows 7 - svchost high cpu usage.

  - by Leonardo

  Hey guys! I'm having a problem with windows 7 x64 i though it was slow and all then i saw that the cpu usage was always around 80% and started digging through google. there's two svchost consuming around 30% each and in the resources monitor there's a system interrupts consuming 45% all the time, i trid closing the aplications and makes no diference. so i tried some other things that i've found on gloogle like disable system update but didn't work. i'd love some help here. i don't know if it will help but here's my specs: Core 2 duo 4400 ATI radeon 4850 4gb ram DDR2 thanks anyway for your attention :) EDIT So i run the program and i got this info, did i get it right? EDIT As you asked here it is, did i get it right now? the other tcp/ip there's nothing. thanks again! :D EDIT I tried somthing here, i run msconfig and took the services that one of the svchost was using out of the startup and now my cpu is around 50%, but i still would like to make this better, i can't lose that much cpu power just because windows... thanks. EDIT yeah there's nothing i can do here, going to install xp for a while, it's really weird...

  Read the article

• not able to register sip user on red5server, using red5phone

  - by sunil221

  I start the red5, and then i start red5phone i try to register sip user , details i provide are username = 999999 password = **** ip = asteriskserverip and i got --- Registering contact -- sip:[email protected]:5072 the right contact could be --- sip :99999@asteriskserverip this is the log: SipUserAgent - listen -> Init... Red5SIP register [SIPUser] register RegisterAgent: Registering contact <sip:[email protected]:5072> (it expires in 3600 secs) RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout RegisterAgent: Failed Registration stop try. Red5SIP Client leaving app 1 Red5SIP Client closing client 35C1B495-E084-1651-0C40-559437CAC7E1 Release ports: sip port 5072 audio port 3002 Release port number:5072 Release port number:3002 [SIPUser] close1 [SIPUser] hangup [SIPUser] closeStreams RTMPUser stopStream [SIPUser] unregister RegisterAgent: Unregistering contact <sip:[email protected]:5072> SipUserAgent - hangup -> Init... SipUserAgent - closeMediaApplication -> Init... [SIPUser] provider.halt RegisterAgent: Registration failure: No response from server. [SIPUser] SIP Registration failure Timeout please let me know if i am doing anything wrong. regards Sunil

  Read the article

• Error creating ODBC connection to SQL Server 2008 Express

  - by DavidB

  When creating a System DSN, I get the error: Connection failed: SQLState: '08001' SQL Server Error: 2 [Microsoft][SQL Server Native Client 10.0]Named Pipes Provider: Could not open a connection to SQL Server [2]. Connection failed: SQLState: 'HYT00' SQL Server Error: 0 [Microsoft][SQL Server Native Client 10.0]Login timeout expired I'm running Vista Home Premium 64-bit SP2, and installed SQL Server 2008 Express Advanced without errors. I'll be using the database locally for an app installed on the same PC. I'm able to successfully connect with SQL Server Management Studio using Windows Authentication (my Windows account is a member of local Administrators), and I can successfully create a database with default ownership (defaults to my Windows account). SQL Server Configuration Manager shows that Shared Memory, TCP/IP, and Named Pipes are enabled for SQL Native Client 10.0 Configuration, SQL Native Client 10.0 Configuration (32bit), and SQL Server Network Configuration (SQLEXPRESS). The SQL Server (SQLEXPRESS) and SQL Server Reporting Services (SQLEXPRESS) services are running. When I create a system DSN, my driver choices are SQL server (sqlsrv32.dll 4-10-09), which gives a generic wizard, and SQL Server Native Client 10.0 (sqlncli10.dll 7-10-08), which gives the SQL Server 2008 wizard. I choose the latter. I enter name, description, and have tried both MyPCName and 127.0.0.1 for the server name (browsing turns up nothing). After clicking Next, I leave it at Integrated Windows authentication, and leave Connect to server for additional options checked. After clicking Next, I get the error above. I know it's probably a simple answer, (permission issue?) and I'm a SQL noob, so I appreciate anything that would point me in the right direction. Thanks!

  Read the article

• How to choose which network connection provides the default gateway in Windows XP

  - by Cathy

  I have a laptop with an integrated NIC and a WiFi connection. Both the wired and wireless networks I am using can access the Internet. Win XP is routing all traffic through the wireless network. I want to force it to route everything through the wired network when it is available (i.e. when I am sitting at my desk with the laptop docked) and through the wireless when that is the only option (i.e. when I have undocked my laptop and carried it to a conference room, or if I am out of the office working on a different WiFi network). The wireless connection cannot be established until after I am logged into Windows, so it's always the second network to become available to the OS. I have manually overridden the metric values in the TCP/IP configurations so that the NIC has metric 10 and the WiFi has metric 20. However, Windows is still picking the WiFi adapter's address as the Default Gateway, so this isn't helping. If I manually disable and re-enable the WiFi adapter, then it will switch the default gateway to the wired network and stay that way until I shutdown Windows. How can I tell Windows XP not to replace the default gateway when the WiFi connection is first enabled?

  Read the article

• Can not access SQLServer database

  - by btrey

  I'm trying to convert an Access database to use a SQLServer backend. I've upsized the database and everything works on the server, but I'm unable to access it remotely. I'm running SQLServer Express 2005 on Windows Server 2003. The server is not configured as a domain controller, nor connected to a domain. The computers I'm trying to access the server from are part of a domain, but there are no local domain controllers. I'm at a remote location and the computers are configured and connected to the domain at the home office, then shipped to us. We normally log in with cached credentials and VPN into the home office when we need to access the domain. I can use Remote Desktop Connection to access the 2k3 server which is running SQLServer. If I log into the server with my username, I can bring up the database, access it via the Trusted Connection, and the database works. If I try to run the database locally, however, I get the Server Login dialog box. I can not use a Trusted Connection because my local login is to the home office domain and is not recognized by the SQLServer machine. If I try to use the username/password that is local to the SQLServer, I get a login failed error. I've tried entering the username as "username", "workgroup/username" (where "workgroup" is the name of the workgroup on the SQLServer), "sqlservername/username" and "[email protected]" where "1.2.3.4" is the IP of the SQLServer. In all cases, I get a login failed error. As I said, I can login to the server via Remote Desktop Connection with the same username and password and use the database, so permissions for the username appear to be correct for both a remote connection and for database access. Not sure where to go from here and any assistance would be appreciated.

  Read the article

• Directory directive: AuthType None but still need an AuthProvider?

  - by Steffen Winkler

  For now I just need the server to let me download files from one specific folder (in my case I chose /opt/myFolder for that task) Distribution is Debian 6.0 *edit_start* Apache version is 2.4, according to their official documentation, the Order/Allow clauses are deprecated and should not be used anymore I'm an idiot: Apache version is 2.2. *edit_end* My directory directives in apache2.conf look like this: <IfModule dir_module> DirectoryIndex index.html index.htm index.php </IfModule> ServerRoot "/etc/apache2" DocumentRoot "/opt/myFolder" <Directory /> Options FollowSymLinks AuthType None AllowOverride None Require all denie </Directory> <Directory "/opt/myFolder/*"> Options FollowSymLinks MultiViews AllowOverride None AuthType None Require all allow </Directory> When I try to access a file inside that folder (http://myserver.de/aTestFile.zip) I get an Internal Server Error. Also Apache writes the following error into it's log: configuration error: couldn't check user. Check your authn provider!: /aTestFile.zip Why would I need an authn provider if I don't want any authentication? Also I hope someone can explain to me what kind of AuthenticationProvider I'd need for that. Everytime I search for those things I get pointed at people asking how to protect files/directories with passwords or restrict access to some IP addresses, which doesn't really help me. ok, since I've Apache version 2.2, here is the error I get when using the Order/Deny/Allow commands instead of AuthType/Require: Invalid command 'Order', perhaps misspelled or defined by a module not included in the server configuration.

  Read the article

• Download JDK onto a remote server

  - by itsadok

  I want to get the latest JDK onto a server in a remote location. Downloading the JDK from Sun's website requires jumping through all kinds of hoops until you actually get the file. I'm not sure exactly if they use cookies or my IP address, but simply copying the file URL and trying wget on the server doesn't work. Googling for mirrors of the JDK, I could only find old versions. Right now I'm left with the option of downloading it into my computer, then uploading it to the server. This feels slow and stupid. Anyone got a better idea? EDIT: Thanks for all the replies. Just to clarify, as I'm writing this I'm rsyncing the 78MB file to my server. It should be done in about an hour, so it's not such a big deal. However, since this is not the first time I'm doing this, I was hoping for a better solution for next time. Solution: What I ended up doing was sudo aptitude install lynx-cur www-browser http://java.sun.com/javase/downloads/ From there it's mostly using the arrow and enter keys, and answering "Yes" to a lot of lynx security questions (about cookies and certificates). Thanks to resonator.

  Read the article

• How do I specify the emergency location in CDP?

  - by chrish

  In the LLDP-MED and Cisco Discovery Protocol whitepaper, it compares LLDP-MED and CDP. The part I am interested in is emergency location configuration. In LLDP-MED, I can specify the Emergency Line Indentification Number (ELIN) and that number will be used by some IP Phones (e.g. Aastra) when placing emergency calls. The whitepaper states: Location Identification Discovery This capability is important because it normally provides location information from the switch to the phone. (If the phone is configured with location information or can determine its location, then it may send this information to the switch. However, the real value is getting this information from the switch to the phone for phones that cannot determine their own location.) Location identification discovery allows the phone to be aware of its location-information that can be used for location-based applications on the phone. More importantly, this capability can be used to provide location information when making emergency calls. Both Cisco Discovery Protocol and LLDP-MED support the transportation of location information. However, LLDP-MED has more supported data formats than Cisco Discovery Protocol. I have found the documentation on how to set the location and associate the location to the interfaces for LLDP-MED. How is this done for CDP? Is ELIN supported for CDP?

  Read the article

• Test server on a local network with XAMPP

  - by hopscotch1978

  Hi, I'm not very proficient with networks and could use some help. I've got a Win 7 desktop with XAMPP which acts as my local dev machine. I've configured a virtual host on the desktop which I'm able to access fine. If I'm understanding things correctly, the virtual host uses port 80 (<VirtualHost 127.0.0.1:80>). I've just tried to configure a separate Win XP laptop on the local wireless network to connect to the main desktop for testing purposes. I've added the IP address and virtual host name to my Hosts file on the laptop. My virtual host is imaginatively named "virtualhost1". When I type this into my laptop browser, it connects correctly to the main desktop and I get the XAMPP welcome screen. But I can't seem to get to the actual site, just the XAMPP welcome screen. It kind of jumps the browser to http://virtualhost1/xampp/. I think it's a port issue of some sort but I have no idea how to resolve it. I would get the same XAMPP welcome screen on my desktop if I omitted ":80" from the virtual host declaration. On my main desktop, typing "virtualhost1" to the browser address bar gives me the site correctly, not the XAMPP welcome screen. Help would be appreciated. Thank you.

  Read the article

• Can I autoregister my clients/servers in local DNS?

  - by Christian Wattengård

  Right now I have a W2k12 server at home that I run as a domain controller. This has the extra benefit of registering every "subordinate" computers name in it's DNS so that I don't have to go around remembering IP's all the time. (And it let's me easily run dhcp also on my servers). I need to rework my home network for several odd reasons, and in this new scenario there is no place for a big honking W2k12 server box. I have a RasPI, and I have other smallish linux boxen I can use. (In a worst case scenario I'll use my NUC, but then I'll be forced to use my home cinema's UPnP-client for media... The HORROR!!) Is it possible to set up a DNS-server-"appliance" that somehow autoregisters it's own hostname.. Scenario: Router (N66u) on 172.20.20.1. Runs DHCP on 172.20.20.100-200 range. Server [verdant] of a *nix flavor on 172.20.20.2 Laptop [speedy] of W8 flavor on DHCP assigned Laptop [canary] of W8 flavor on DHCP assigned Desktop [lianyu] of Ubunto flavor on DHCP assigned What I would like is that all of the above servers (except possibly the router) would be available on verdant.starling.lan and canary.starling.lan and so on. This is how it works right now (except the Ubuntu box... I haven't cracked that one yet) because Windows just does this for you.. I would also be able to do this without any manual labor on the server. When I tell my box it's name is smoak it should "immediately" be available as smoak.starling.lan without any extra configuration on my part. How can I do this in a Linux (Ubuntu) environment? (Bonus comment upvote for naming the naming scheme :P )

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

• Measure Total Bandwidth for Billing

  - by TonyZ

  I am setting up a new network which customers will host their applications on. It needs to be able to scale out to a few hundred servers and each server will have several VMs on it. Right now in my test environment, after the telco router, we are using a Linux router/firewall which is then connected to a Layer 2 switch. Could be a layer 3 in the future. I need to track total bandwidth per VM for each machine, and I need to do it in a way that it is not part of the VM. Each VM will have a private class ip address which is Natted by the gateway, or we may eventually run more than firewall/reverse proxy off a layer 3 switch. So my thinking is that I can do it off of a promiscuous port on the switches, or at the gateway firewall. I would like to have an out of the box solution, preferably open source. Does anyone have suggestions on the easiest way to set this up, and the easiest tool to use. I have looked at the web sites for Nagios, Zenoss, Zabbix, ntops on the firewall, etc. It is hard to ascertain just from the web sites if they do exactly this or not. Obviously, performance is also somewhat key here. Anything running on the gateway should not drag it down doing traffic accounting. Thanks for any thoughts. Tony Zakula

  Read the article

• Simulated NAT Traversal on Virtual Box

  - by Sumit Arora

  I have installed virtual box ( with Two virtual Adapters(NAT-type)) - Host (Ubuntu -10.10) - Guest-Opensuse-11.4 . Objective : Trying to simulate all four types of NAT as defined here : https://wiki.asterisk.org/wiki/display/TOP/NAT+Traversal+Testing Simulating the various kinds of NATs can be done using Linux iptables. In these examples, eth0 is the private network and eth1 is the public network. Full-cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source iptables -t nat -A PREROUTING -i eth0 -j DNAT --to-destination Restricted cone iptables -t nat POSTROUTING -o eth1 -p tcp -j SNAT --to-source iptables -t nat POSTROUTING -o eth1 -p udp -j SNAT --to-source iptables -t nat PREROUTING -i eth1 -p tcp -j DNAT --to-destination iptables -t nat PREROUTING -i eth1 -p udp -j DNAT --to-destination iptables -A INPUT -i eth1 -p tcp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p udp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p tcp -m state --state NEW -j DROP iptables -A INPUT -i eth1 -p udp -m state --state NEW -j DROP Port-restricted cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source Symmentric echo "1" /proc/sys/net/ipv4/ip_forward iptables --flush iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE --random iptables -A FORWARD -i eth1 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT What I did : OpenSuse guest with Two Virtual adapters - eth0 and eth1 -- eth1 with address 10.0.3.15 /eth1:1 as 10.0.3.16 -- eth0 with address 10.0.2.15 now running stund(http://sourceforge.net/projects/stun/) client/server : Server eKimchi@linux-6j9k:~/sw/stun/stund ./server -v -h 10.0.3.15 -a 10.0.3.16 Client eKimchi@linux-6j9k:~/sw/stun/stund ./client -v 10.0.3.15 -i 10.0.2.15 On all Four Cases It is giving same results : test I = 1 test II = 1 test III = 1 test I(2) = 1 is nat = 0 mapped IP same = 1 hairpin = 1 preserver port = 1 Primary: Open Return value is 0x000001 Q-1 :Please let me know If any has ever done, It should behave like NAT as per description but nowhere it working as a NAT. Q-2: How NAT Implemented in Home routers (Usually Port Restricted), but those also pre-configured iptables rules and tuned Linux

  Read the article

• Xen Windows Guest spawn doesn't spawn a vnc display

  - by Henrik P. Hessel

  I'm using this HVM File to create a new guest kernel = "/usr/lib/xen-3.2-1/boot/hvmloader" builder='hvm' memory = 4096 # Should be at least 2KB per MB of domain memory, plus a few MB per vcpu. shadow_memory = 64 name = "hessel-windows2008" vif = [ 'ip=188.40.xx.xx,mac=00:16:3E:C1:8F:CE' ] acpi = 1 apic = 1 disk = [ 'file:/home/xen/disks/hessel/win2008/win2008.img,hda,w', 'file:/home/xen/isopool/win2008_32.iso,hdc:cdrom,r' ] device_model = '/usr/lib/xen/bin/qemu-dm' #----------------------------------------------------------------------------- # boot on floppy (a), hard disk (c) or CD-ROM (d) # default: hard disk, cd-rom, floppy boot="dc" sdl=0 vnc=1 vncdisplay=1 vnclisten="0.0.0.0" vncconsole=1 vncpasswd='howtoforge' stdvga=0 serial='pty' usbdevice='tablet' The guest is created without an error. But no vnc display is created. Any ideas, how to fix that? prometheus:~# netstat -ant Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:615 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:6010 0.0.0.0:* LISTEN tcp 0 232 188.40.xx.xx:8080 195.36.75.26:54032 ESTABLISHED tcp 0 0 188.40.xx.xx:8080 195.36.75.26:53085 ESTABLISHED tcp6 0 0 :::8080 :::* LISTEN tcp6 0 0 :::53 :::* LISTEN tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 ::1:6010 :::* LISTEN

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• sharing a folder between linux and windows over the internet

  - by valya

  Hello Currently my job is to make websites with Django. I use many things like virtualenv, PIL, etc. The problem is, I can't stand Linux on my desktop. I like it on servers, It's greate to use it over the SSH. But for desktop? No way. But for the development Linux is quite essential. Of course almost everything is ported to Windows, but it's not as simple to use as in Linux. For example, Windows shell is awful in comparison with Linux. So I've tried Cygwin, but it's too damn slow. Every time django dev server reloads, it tooks almost 20-30 seconds. In comparison, then using "native" python on Windows or Linux, it reloads instantly. Even worse, Cygwin makes all my system very slow. I've been thinking about it and have thought up a way to go. I can share a folder with my application with some Linux box. The devserver and everything will run on that box, while I'll be happy editing files and running the browser on my Windows 7. SSH shell is much quickier and handy than Cygwin. Currently there are no Linux boxes in my home network (except for my android phone :) but I have several VDS boxes with Debian. So, how do I share a Windows folder with VDS box? I can't rely on my desktop IP but I can rely on the VDS's one. I need sharing to be as quick as possible (well, 2-3 seconds ping is OK) and "native" for both systems, so I could use a folder like a normal folder in both Windows and Linux.

  Read the article

• BIND9 server types

  - by aGr

  I was configuring DNS on my server using BIND9, everything seems to work, but I have a question regarding my config file. I've ended up with this configuration in /etc/bind/named.conf.local zone "example.com" { type master; file "/etc/bind/db.example.com"; allow-transfer { 192.168.1.1; }; }; zone "1.168.192.in-addr.arpa" { type master; notify no; file "/etc/bind/db.192"; allow-transfer { 192.168.1.1; }; }; forwarders { 10.253.22.140; 10.253.22.141; }; I've read about the different type of dns server, like primary master etc. The first two parts (zone and zone) corresponds to primary dns server configuration. First record for "classic" lookup, second one for reverse. The last part (forwarders) is configuration of cache-server and contains the ISP's IP of DNS server. So all names resolved thanks to this server will be cached. Simple question: am I right? Does my description make sense? Or one server can be only either master or either cached?

  Read the article

• flowchart for debugging a slow/unresponsive server

  - by davidosomething

  So the server is slow: Roll back to the previous known working build - Success? Code problem - Fail? Go on. Ping ip address - Success? maybe a DNS problem, go on. - Fail? Server or connection problem, go on. Ping and tracert your domain.com from inside your network - previous success - fail: DNS problem - success? go on. - previous fail and: - Fail? Go on, could be you or network. - Success? Go on. Try it from outside your network (http://centralops.net/co/) - Fail? The server's network connection sucks. - Success? If inside network was fail, your network sucks. Check the server load: CPU/RAM usage. Is it overloaded? - Yes. Who's the culprit? Kill some processes/reboot. - No? Go on. what other steps should i add?

  Read the article

• nginx: SSI working on Apache backend, but not on gunicorn backend

  - by j0nes

  I have nginx in front of an Apache server and a gunicorn server for different parts of my website. I am using the SSI module in nginx to display a snippet in every page. The websites include a snippet in this form: For static pages served by nginx everything is working fine, the same goes for the Apache-generated pages - the SSI include is evaluated and the snippet is filled. However for requests to my gunicorn backend running a Python app in Django, the SSI include does not get evaluated. Here is the relevant part of the nginx config: location /cgi-bin/script.pl { ssi on; proxy_pass http://default_backend/cgi-bin/script.pl; include sites-available/aspects/proxy-default.conf; } location /directory/ { ssi on; limit_req zone=directory nodelay burst=3; proxy_pass http://django_backend/directory/; include sites-available/aspects/proxy-default.conf; } Backends: upstream django_backend { server dynamic.mydomain.com:8000 max_fails=5 fail_timeout=10s; } upstream default_backend { server dynamic.mydomain.com:80; server dynamic2.mydomain.com:80; } proxy_default.conf: proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; What is the cause for this behaviour? How can I get SSI includes working for my pages generated on gunicorn? How can I debug this further?

  Read the article

• Debian DNSSEC - howto secure a domain?

  - by Daniel Marschall

  I have a beginner question about DNSSEC. I have much experience with TLS and cryptography-stuff and would like to try out this new technology. I have googled very much about this but I haven't found useful information for me. I think one confusion in information gathering is that "Debian howto DNSSEC setup" can mean "How to USE DNSSEC for resolving" OR "How to secure your domain with DNSSEC". I am searching the second. I am running a Debian Squeeze server with root privileges which has a domain name ending with ".de" (which is already signed by the root zone). The network interface at this server uses the gateway IP (DNS resolver?) of the datacentre the server is running on. My domain is hosted at freedns.afraid.org , where I can add DNS RRs for my domain. They are currently NOT capable of adding DNSSEC RRs, but I am bugging them to support this soon. ;-) My simple question is: How do I setup DNSSEC on Debian? Resp. who have I ask to? As far as I understand, all I have to do is to run dnssec-keygen on my Debian server and then add the key to my DNS-provider as DNSSEC RR. (And change it every 30 days?) I have looked at this http://www.isc.org/files/DNSSEC_in_6_minutes.pdf but it looks like you have to be the owner of a ZONE, so I don't think this applies to me. Who needs to sign my domain? My DNS-provider or my zone (DeNIC) or can I do it myself? Any help is very appreciated!

  Read the article

• how to define service runlevel order position?

  - by DmitrySemenov

  I setup bind-dlz and need mysql start prior NAMED when system starts here is what I have [root@semenov]# ./test.sh mysql 0:off 1:off 2:on 3:on 4:on 5:on 6:off named 0:off 1:off 2:off 3:on 4:on 5:on 6:off lrwxrwxrwx. 1 root root 15 Apr 15 18:57 /etc/rc3.d/S93mysql -> ../init.d/mysql lrwxrwxrwx. 1 root root 15 Apr 15 18:57 /etc/rc3.d/S90named -> ../init.d/named here is what I have in mysql init script # Comments to support chkconfig on RedHat Linux # chkconfig: 2345 84 16 # description: A very fast and reliable SQL database engine. # Comments to support LSB init script conventions ### BEGIN INIT INFO # Provides: mysql # Required-Start: $local_fs $network $remote_fs # Should-Start: ypbind nscd ldap ntpd xntpd # Required-Stop: $local_fs $network $remote_fs # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: start and stop MySQL # Description: MySQL is a very fast and reliable SQL database engine. ### END INIT INFO so when I remove named from chkconfig and have there just mysql, it starts with order number 84: /etc/rc3.d/S84mysql - ../init.d/mysql but when I add named inside chkconfig it's order changes to 93: /etc/rc3.d/S93mysql - ../init.d/mysql as a result mysql will be starting after named and named will fail (no sql available) any ideas what I'm doing wrong? here is what I have in named init script # chkconfig: 345 90 16 # description: named (BIND) is a Domain Name Server (DNS) \ # that is used to resolve host names to IP addresses. # probe: true ### BEGIN INIT INFO # Provides: $named # Required-Start: $local_fs $network $syslog # Required-Stop: $local_fs $network $syslog # Default-Start:2 3 4 # Default-Stop: 0 1 2 3 4 5 6 # Short-Description: start|stop|status|restart|try-restart|reload|force-reload DNS server # Description: control ISC BIND implementation of DNS server ### END INIT INFO thanks, Dmitry

  Read the article

• Solaris 10: cannot ping to/from server

  - by anurag kohli

  All, I have a Solaris 10 server which is not reachable by IP (ie can't ping to/from the server). I believe I have the default route setup correctly. See below: # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.62.100 netmask ffffff00 broadcast 192.168.62.255 ether 0:14:4f:b1:9b:30 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.62.0 192.168.62.100 U 1 40 bge0 224.0.0.0 192.168.62.100 U 1 0 bge0 default 192.168.62.1 UG 1 0 127.0.0.1 127.0.0.1 UH 1 4 lo0 # # cat /etc/defaultrouter 192.168.62.1 I have verified layer1 and layer 2 are up on the switchport, and that it's on the correct VLAN. I have also checked the default gateawy (192.168.62.1) is in fact reachable since I can ping it from my PC: Pinging 192.168.62.1 with 32 bytes of data: Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=3ms TTL=254 Reply from 192.168.62.1: bytes=32 time=6ms TTL=254 I'm at a loss as to what is wrong. I would highly appreciated your assistance. Thank you very much.

  Read the article

• Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

  - by Nick

  I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

  Read the article

< Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399  | Next Page >