Search Results

Search found 11313 results on 453 pages for 'ip aliasing'.

Page 395/453 | < Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Website has become slower on a VPS, was much fast on a shared host. What's wrong?

    - by Arpit Tambi
    My shared host suspended my website stating system overload, so I moved my website to a VPS which has 4GB RAM. But for some reason the website has become very slow. This is the vmstat output - procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 3050500 0 0 0 0 0 1 0 0 0 0 100 0 0 Here's the Apache Benchmark output for a STATIC html page I ran on the server itself - Benchmarking www.ask-oracle.com (be patient)...apr_poll: The timeout specified has expired (70007) Total of 20 requests completed Update: Server Config: List item Centos 5.6 4 cores cpu 4 GB RAM LAMP stack with APC Wordpress Only one website It takes almost double time to load now, same website was much fast on shared hosting. I know I need to tweak some settings but have no clue where to start from? I have already tried to optimize apache, mysql etc. Update 2: CPU usage is low, see uptime output: 11:09:02 up 7 days, 21:26, 1 user, load average: 0.09, 0.11, 0.09 Update 3: When I load any webpage, browser shows "Waiting" for a long time and then page loads quickly. So I suspect server can accept only limited connections and holds extra connections in a waiting state. How to check this? Update 4: Following is the output on executing netperf TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to localhost.localdomain (127.0.0.1) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.00 9615.40 [root@ip-118-139-177-244 j3ngn5ri6r01t3]# Here are the Apache MPM settings from httpd.conf, do they look okay? <IfModule worker.c> StartServers 5 MaxClients 100 MinSpareThreads 50 MaxSpareThreads 250 ThreadsPerChild 125 MaxRequestsPerChild 10000 ServerLimit 100 </IfModule>

    Read the article

  • Vlans and subinterfaces

    - by Adeodatus
    I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

    Read the article

  • Vista laptop 1 connects to network but Vista laptop 2 doesn't

    - by Jaips
    (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

    Read the article

  • Chrome browser completely messing with network?

    - by kiasecto
    I have a bizare problem with Google Chrome on a intel core i5 running windows 7 32bit. Whenever chrome is installed, access to other computers in the home group becomes really slow - such as opening shares. Its becomes really slow to resolve windows names. Something goes hay-wire with the local network - pining local machines which is usually 0mS pings I get random timeouts and random successes. Whenever I try to load a local address inside of chrome (including localhost, 192.168.0.1 etc) - it always says something in the status bar about resolving proxy and times out after about 5 seconds, then seems to work fine. If I go to settings inside of chrome, it just brings up the internet explorer connection settings, where I have not set any proxy settings. One I uninstall chrome, all these problems go away. Network shares and name resolvings work instantly, pings to any machines never have a problem. Localhost and other network IP address work fine in all other browsers. Anyone heard of this problem before and know what it might be? I even tried re-installing winodws 7 and the problem came straight back when chrome was loaded on again.

    Read the article

  • Tripwire help Required

    - by ramaperumal
    I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

    Read the article

  • Bridging my laptop's wireless and wired adaptors

    - by stacey.richards
    I would like to be able to connect a desktop computer that does not have a wireless adapter to my wireless network. I could just run a network cable from my ADSL/wireless router to the desktop computer but sometimes this is not practical. What I would really like to do is bridge my laptop's wireless and wired adapters in such a way that I can run a network cable from my laptop to a switch and another network cable from the switch to a desktop computer so that the desktop computer can access the Internet through my ADSL/wireless router via my latop: +--------------------+ |ADSL/wireless router| +--------------------+ | +-------------------------+ |laptop's wireless adaptor| | | |laptop's wired adaptor | +-------------------------+ | +------+ |switch| +------+ | +-----------------------+ |desktop's wired adapter| +-----------------------+ A bit of Googling suggests that I can do this by bridging my laptop's wireless and wired adapters. In Windows XP's Network Connections I select both the Local Area Connection and the Wireless Network Connection, right click and select Bridge Connections. From what I gather, this (layer 2?) bridge will examine the MAC address of traffic coming from the wireless network and pass it through to the wired network if it suspects that a network adapter with that MAC address may be on the wired side, and vice-versa. If this is the case, I would assume that when the desktop computer attempts to get an IP address from a DHCP server (which is running on the ADSL/wireless router), it would send a DHCP broadcast packet which would pass through the laptop's bridge to the router and the reply would return through the laptop's bridge back to the desktop. This doesn't happen. With some more Googling I find some instruction how this can be done with Linux. I reboot to Ubuntu 9.10 and type the following: sudo apt-get install bridge-utils sudo brctl addbr br0 sudo brctl addif br0 wlan0 sudo brctl addif br0 eth0 sudo ipconfig wlan0 0.0.0.0 sudo ipconfig eth0 0.0.0.0 Once again, the desktop cannot reach the ADSL/wireless router. I suspect that I'm missing some simple important step. Can anyone shed some light on this for me?

    Read the article

  • VMWare converter performance

    - by bellocarico
    Hello, I have a question about my test lab. It's more to understand the concept more than apply this into production: I have an ESXi with few VMs linux/windows configured and I'd like to use VMWare converter to create backups. To speedup the process I decided to create a Windows VM on the same ESXi host where I've installed Windows 7 and VMWare Converter. The Host has a gigabit card but it's currently connected to a 100Mb FD port. Windows 7 sees a 1gb card connected. When I do the backup using VMWare converter I specify the host IP as source and destination, so I thought the copy could be faster then use my laptop across the network. Well, to cut a long sotry short: I get dreadful performance (4Mb/sec). I'm a buit confused on this because despite the fact that the host is running 100Mb communication between VMs and hosts shouldn't (correct me if I'm wrong) have any limitation instead. I did tweak windows 7 to optimise network performane but I got just a little improvement. i still need 4 hours to back up a 50Gb (thin) VM. Additionally I wanted to ask: Would jumbo frame help in this? I know that jumbo frame have to be supported end to end, and the network switch where the host is currently connected doesn't support this, but I was wondering: 1) Does ESXi host support jumbo frames at all? 2) Can I enable it somehow? 3) If I do so, I guess bulk transfert between VMs and host would improve, but would this affect the communication going through the real switch as this doesn't do jumbo? Thanks for reading

    Read the article

  • Problem IIS 7.0 Locking files durring upload

    - by viscious
    I am running a server 2008 with iis7 and the ftp addon on to iis 7.0 I have the ftp site configured and mostly working Except that about 70% of the time when transferring a file the upload will hang forever. If I disconnect the ftp client and reconnect and try to upload the same file I will get an error on the client saying the file is locked. I have to restart the ftp service to clear the lock. I fired up process explorer and did a search on the file in question and sure enough the ftp service has a lock on the file and it takes around 20 minutes to release the lock on its own (and sometimes longer). This lock stays around even after I disconnect the client. Like I said this only happens about 70% of the time, the other 30% of the time it goes through just fine. Things i have verified. -Not a firewall issue. Server is using passive port range 8000-9000 which is allowed on the firewall. -Not a nat issue, server has a globally rout-able ip address -all recommended/required updates installed I have 5 other servers in a very similar configuration and this is the only one i have problems with.

    Read the article

  • How to Install OS without DVD and USB boot

    - by Timothy James Reed
    I just purchased a used Dell F1D 1U rack mount server and would like to install Ubuntu or ESXi with Virtual Disks or anything for that matter. I'v read that Dell's have built in DRAC so you can access it remotely. There are 3 ethernet plugs in the back but I dont know which one to use. In the BIOS it says I can configure Remote access on [com1] or [com2] not sure if that is ethernet 1 & 2. I also set it up so to use a static IP adress. Thats as far as I have gone. Not sure what to do next. I'v Tried to do a PXE server with TFTP but get stuck at Error "cant locate file" or something like that. Not even sure I want to go that route anymore because of all the hassel of editing files. All my computers are OSX or Linux and the only Windows I have is via VMWare. What steps to i do now?

    Read the article

  • BIND master/slave does not respond for queries for its slave

    - by Savas
    Systems are all Centos 6.2 Lets say I have a masterdns with IP 10.2.1.2, authoritative for the 10.2.1.X subnet and let say it is domain example.com I have another two subnets, 10.2.2.X and 10.1.2.X Each one has its own DNS server, dns2 and dns1 respectively and let say these are domains dom2.example.com and dom2.example.com respectively. The masterdns server has slave zones for dns1, dns2 and respond to requests OK. The dns1, dns2 have the masterdns zones as slaves two, and respond to requests OK. So, the masterdns has as slave zones all the subordinate domains of example.com Each of dns1 and dns2 use masterdns as a forwards (which uses another dns cache/proxy server) for dns resolution of internet public domain names. It works OK that too. The problem is, and I cannot figure it out. Why queries for example at dns1 for hostnames of dom2.example.com do not resolve? If i use nslookup - masterdns at dns1 server, resolve (i use directly the dns facility of masterdns). If I use nslookup locally, meaning queries are sent to dns1, for hosts that are at dom2.example.com, they do not resolve. Everything other works OK.

    Read the article

  • Torrent upload ratio not updated on Synology DS212+

    - by user179271
    I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • How do I specify the emergency location in CDP?

    - by chrish
    In the LLDP-MED and Cisco Discovery Protocol whitepaper, it compares LLDP-MED and CDP. The part I am interested in is emergency location configuration. In LLDP-MED, I can specify the Emergency Line Indentification Number (ELIN) and that number will be used by some IP Phones (e.g. Aastra) when placing emergency calls. The whitepaper states: Location Identification Discovery This capability is important because it normally provides location information from the switch to the phone. (If the phone is configured with location information or can determine its location, then it may send this information to the switch. However, the real value is getting this information from the switch to the phone for phones that cannot determine their own location.) Location identification discovery allows the phone to be aware of its location-information that can be used for location-based applications on the phone. More importantly, this capability can be used to provide location information when making emergency calls. Both Cisco Discovery Protocol and LLDP-MED support the transportation of location information. However, LLDP-MED has more supported data formats than Cisco Discovery Protocol. I have found the documentation on how to set the location and associate the location to the interfaces for LLDP-MED. How is this done for CDP? Is ELIN supported for CDP?

    Read the article

  • NAT confusion regarding cisco ASA5510

    - by LonelyLonelyNetworkN00b
    I'm setting up my first cisco firewalls. A little information first:I have two asa5510 setup in a working active/standby pair. From my ISP i have two public subnets. A /29 and a /26. On my DMZ interface i have the /26 configured. On my WAN Interface i have configured the /29 IPs. My isp routes the /26 via the /29 primary IP. I'm running ASA 8.2. I've turned NAT-Control off, because i don't want to use nat for for other than some internal interfaces. In essence i don't want to use NAT unless i specify it. I have a internal interface with the network of 192.168.100.0/24. I've tried setting up nat limke this: nat (inside) 1 192.168.100.0 255.255.255.0 global (WAN) 1 interface I was under the impression that this would let connections that was going from 192.168.100.0/24 and out the WAN interface to be Port-Address-translated. I'm not getting this to work for some reason. Inside interface has security level of 100, and wan has security level of 0.

    Read the article

  • Nginx and Gunicorn hanging on GET requests

    - by whatWhat
    I'm using Nginx + Gunicorn which is serving my Django project. All GET requests hang for ~1 min. The content seems to be available immediately as I can see it in the Browser inspector but the browser itself looks like it's still waiting for more data. Heres my Ngnix config #allow for up to 3 connections per second. limit_req_zone $binary_remote_addr zone=one:10m rate=3r/s; server { listen 80; server_name example.com; root /var/www/example.com/example/; # serve directly - analogous for static/staticfiles location /media/ { # this changes depending on your python version root /home/example/; } location /static/ { # if asset versioning is used if ($query_string) { expires max; } root /var/www/example.com; } location / { #Allow for a burst of 50. limit_req zone=one burst=50 nodelay; proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 10; proxy_pass http://localhost:8001/; } # what to serve if upstream is not available or crashes error_page 500 502 503 504 /media/50x.html; } My Gunicorn Config: bind = "127.0.0.1:8001" workers = 3 worker_class = "gevent" Is there anything obvious that would be causing the requests to stay open for so long?

    Read the article

  • OpenVPN Keeps Crashing

    - by Frank Thornton
    Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28523 [vpntest] Peer Connection Initiated with [AF_INET]<MY_IP>:28523 Oct 20 21:00:44 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 MULTI_sva: pool returned IPv4=10.8.0.6, IPv6=(Not enabled) Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1576', remote='link-mtu 1376' Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1532', remote='tun-mtu 1332' Oct 20 21:00:45 sb1 openvpn[2082]: <MY_IP>:28522 [vpntest2] Peer Connection Initiated with [AF_INET]<MY_IP>:28522 Oct 20 21:00:45 sb1 openvpn[2082]: vpntest2/<MY_IP>:28522 MULTI_sva: pool returned IPv4=10.8.0.10, IPv6=(Not enabled) Oct 20 21:00:46 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 send_push_reply(): safe_cap=940 Client File: client dev tun proto tcp remote <IP> 443 resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1410 persist-key persist-tun auth-user-pass comp-lzo SERVER: port 443 #- port proto tcp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 reneg-sec 0 #mtu-disc yes mssfix 1410 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /etc/openvpn/openvpn-auth-pam.so /etc/pam.d/login #plugin /usr/share/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Comment this line if you are using FreeRADIUS #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment this line if you are using FreeRADIUS client-to-client client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 3 30 comp-lzo persist-key persist-tun What is causing the VPN to keep dropping the connection and then reconnecting?

    Read the article

  • "Network Error - 53" while trying to mount NFS share in Windows Server 2008 client

    - by Mike B
    CentOS | Windows 2008 I've got a CentOS 5.5 server running nfsd. On the Windows side, I'm running Windows Server 2008 R2 Enterprise. I have the "Files Services" server role enabled and both Client for NFS and Server for NFS are on. I'm able to successfully connect/mount to the CentOS NFS share from other linux systems but am experiencing errors connecting to it from Windows. When I try to connect, I get the following: C:\Users\fooadmin>mount -o anon 10.10.10.10:/share/ z: Network Error - 53 Type 'NET HELPMSG 53' for more information. (IP and share name have been changed to protect the innocent :-) ) Additional information: I've verified low-level network connectivity between the Windows client and the NFS server with telnet (to the NFS on TCP/2049) so I know the port is open. I've further confirmed that inbound and outbound firewall ports are present and enabled. I came across a Microsoft tech note that suggested changing the "Provider Order" so "NFS Network" is above other items like Microsoft Windows Network. I changed this and restarted the NFS client - no luck. I've confirmed that the share folder on the NFS server is readable/writable by all (777) I've tried other variations of the mount command like: mount 10.10.10.10:/share/ z: and mount 10.10.10.10:/share z: and mount -o anon mtype=hard \\10.10.10.10:/share * No luck. As per the command output, I tried typing NET HELPMSG 53 but that doesn't tell me much. Just "The network path was not found". I'm lost on how to proceed with troubleshooting. Any ideas?

    Read the article

  • iptables rules to allow HTTP traffic to one domain only

    - by Emily
    Hi everyone, I need to configure my machine as to allow HTTP traffic to/from serverfault.com only. All other websites, services ports are not accessible. I came up with these iptables rules: #drop everything iptables -P INPUT DROP iptables -P OUTPUT DROP #Now, allow connection to website serverfault.com on port 80 iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT #allow loopback iptables -I INPUT 1 -i lo -j ACCEPT It doesn't work quite well: After I drop everything, and move on to rule 3: iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT I get this error: iptables v1.4.4: host/network `serverfault.com' not found Try `iptables -h' or 'iptables --help' for more information. Do you think it is related to DNS? Should I allow it as well? Or should I just put IP addresses in the rules? Do you think what I'm trying to do could be achieved with simpler rules? How? I would appreciate any help or hints on this. Thanks a lot!

    Read the article

  • nginx config woes for multiple subdomains & domains

    - by Peter Hanneman
    I'm finally moving away from Apache and I've got the latest development version of nginx running on a fully updated Ubuntu 10.04 VPS. I've got a single dedicated IP for the box (1.2.3.4) but I've got two separate domains pointing to the server: www.example1.com and www.example2.net. I would like to map the fallowing relationships between urls and document roots in the config: www.example1.com / example1.com -> /var/www/pub/example1.com/ subdomain.example1.com -> /var/www/dev/subdomain/example1.com/ www.example2.net / example2.net -> /var/www/pub/example2.net/ subdomain.example2.net -> /var/www/dev/subdomain/example2.net/ Where the name of the requested subdomain is a folder under /var/www/dev/. Ideally a request for a non-existent subdomain(no matching folder found) would result in a rewrite to the public site (eg: invalid.example1.com -- www.example1.com) however a mere "404 Not Found" wouldn't be the worst thing in the world. It would also be nice if I didn't need to modify the config every time I mkdir a new subdomain folder - even better if I don't need to edit it for a new domain either...but now I'm getting greedy... :p Although in my defense Apache did all of this with a single directive. Does anyone know how I can efficiently mimic this behavior in nginx? Thanks in advance, Peter Hanneman

    Read the article

  • Network latency and speed of light

    - by James
    This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

    Read the article

  • Prevent SSL certificate being returned for a specific domain

    - by jezmck
    Apologies for a long question: We've taken on a new client whose web hosting was previously on their in-house server which still has their Exchange/Outlook email. We now host their domain (and many others) on our server. They're complaining that they're getting errors in Outlook. I don't understand the AutoDiscover stuff at the root of the problem, but believe that I just need to stop the SSL certificate on our server being returned when requested at a particular domain: Yes it is, the issue lies with "{newclient}.com" being pointed to your server IP and that server has Port 443 open with an SSL certificate associated to it. So when Outlook/ActiveSync use autodiscover to find the mailbox settings it find your SSL (because 443 is open) and flags it as an error. The solution is to close 443 so its not discovered, Autodiscover will then proceed to mail.{newclient}.com via the MX / ServiceRecords and discover the correct SSL. I'm new here and there was no hand-over, so I don't know whether other currently hosted sites need to accept SSL connections, though I suspect some will, or may in future. This is a live server, so I can't risk trying loads of options in case I take the server offline! I feel like I should be adding something like the following to vhosts.conf. <VirtualHost *:443> ServerName {newclient}.com ServerAlias www.{newclient}.com SSLEngine Off SSLCertificateFile {NONE} SSLCertificateKeyFile {NONE} </VirtualHost> Apologies for the fact that I don't know enough about this subject to be able to ask the question more clearly!

    Read the article

  • VNC from Windows to OS X Lion: App stuck in fullscreen mode

    - by Jonny
    I'm connecting to a remote Mac through a Windows. ahh it gets more complicated than that. I'm sitting by my iMac. I use Virtual Box in it to launch Windows 7. In it I have a VPN connection to a remote Windows network, which allows me to use Remote Desktop to one of the Windows (Vista!) boxes over there. From that Vista box I VNC into a Mac OS X Lion. (Don't ask me why, but that Mac doesn't have a public ip which prevents me from accessing it in the first place.) So: OSXLion - (virtual)Windows7 - Windows Vista - OSX Lion That last Mac was recently upgraded from Snow Leopard. Now with Lion, sometimes apps run in fullscreen. Somehow I can't get out of that fullscreen. Normally you'd move the mouse pointer to the top of screen and a menu list bar drops down allowing you to reach the fullscreen button top right. Now, in my current setup that menu list bar never drops down on the remote Mac at the end of the line. Any ideas?

    Read the article

  • ssh_exchange_identification: Connection closed by remote host

    - by rick
    Firstly, I know that this question has been asked a million times, and I have read everything I can find and still cannot fix the problem. i am encountering this issue when ssh'ing in from my mac to my Ubuntu server on a fresh install of Ubuntu (I reinstalled because of this issue). I have SSH portmapped to 7070 because my ISP is blocking 22. On the client: bash: ssh -p 7070 -v [email protected] debug1: Reading configuration data /etc/ssh_config debug1: Connecting to address.org port 7070. debug1: Connection established. debug1: identity file /home/me/.ssh/identity type -1 debug1: identity file /home/me/.ssh/id_rsa type 1 debug1: identity file /home/me/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host Here's what I have done to try to resolve the issue: Made sure my maxstartups is ok: bash: grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10:30:60 Made sure hosts.deny is clear of denials. Made sure hosts.allow has my client IP. Clear out known_hosts on client Changed ownership of /var/run to root Made sure etc/run/ssh is Made sure /var/empty exists Reinstall openssh-server Reinstall ubuntu When I run telnet localhost, I get this: telnet localhost Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused When I run /usr/sbin/sshd -t Could not load host key: /etc/ssh/ssh_host_rsa_key Could not load host key: /etc/ssh/ssh_host_dsa_key When I regenerate the keys with ssh-keygen -t rsa -f /etc/ssh/ssh_host_rsa_key ssh-keygen -t dsa -f /etc/ssh/ssh_host_dsa_key I get the same error. I am pretty sure this is the issue. Can anyone help?

    Read the article

< Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >