Search Results

Search found 27521 results on 1101 pages for 'remote control'.

Page 396/1101 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

• SSH from Windows Vista to Ubuntu (using cwrsync)

  - by user39141

  Newbie questoin but I can't seem to figure it out. Using cwrsync which in turn calls ssh.exe from a Windows Vista box to Ubuntu. For below, user in ubuntu is 'linuxuser' and user on Windows box is 'winuser' - remote box is 'linuxhost' and windows box is 'winhost' Exported keys such that on the remote box /home/linuxuser/.ssh/authorized_keys is correctly populated. Problem is when I launch ssh it tries to write to /home/winuser/.ssh instead of /cygdrive/home/users/winuser/.ssh as below. c:\Program Files (x86)\cwRsync\binssh linuxuser@linuxhost Could not create directory '/home/winuser/.ssh'. The authenticity of host 'linuxhost (192.168.1.105)' can't be establish ed. RSA key fingerprint is 67:10:a9:49:6e:a3:2b:4a:a0:e0:b7:75:76:da:c3:04. Are you sure you want to continue connecting (yes/no)? Host key verification failed.

  Read the article

• L2TP Site to Site VPN issues

  - by Chris Lively

  I have a windows 2008 r2 server that needs to establish a VPN connection to a remote VPN server. We're using the L2TP protocol with a pre-shared key. I initially used the New Demand Dial interface wizard. Then I went into properties on the interface and set the type of VPn to L2TP/IPSec and put the key under the advanced settings. The error I received when attempting to connect is: An error occured during connection of the interface. A Demand Dial Router attempted to connect over a port that was reserved for Remote Access Clients only.

  Read the article

• Switch between network configurations via command line in fedora 17

  - by Mike Fairhurst

  I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

  Read the article

• putty ssh client become not responding frequently in windows 7

  - by Sankaran

  with celeron processor and 512 MB ram windows 7 takes too much time even to open a folder in windows explorer. I connect to internet with GPRS modem. When I tried to connect with remote linux machine with putty ssh client. The problem is the putty becomes Not responding in 2 or 3 minutes. I've to connect again and putty goes Not responding again. When i tried in Safe mode with networking, GPRS modem is not even detected. the modem is USB data card. Is it possible load USB drive in safe mode of windows 7 or any other possibility to connect with remote machine via ssh

  Read the article

• Unable to access, make directories (and files) with ftp

  - by Kriem

  I'm having trouble with my new server and accessing its directories. I updated my proftpd.conf with: DefaultRoot / No I'm able to see the root directory of my server. But, trying to access some directories gives different results. For example, I can access /vars but I can't access /home or /root How can I overcome this? This is what my ftp client says after trying to access /root: Server said: /root: No such file or directory Error -125: remote chdir failed This is what my ftp client says after trying to create a new directory in /: Server said: untitled folder: Permission denied Error -140: remote mkdir failed

  Read the article

• How do networking ports work? Can I configure the ports that client and server use?

  - by joedotnot

  Let's say i have a "server" program listening on address 1.2.3.4:69 (i.e. remote port 69) When i connect from a "client" program to it, typically i would specify the IP address + port of the target or server system; But what port would the client be using ? And how does the server know which port to connect back to the client on? I understand this question is very general, but just wanting to get a general feel for how things work. Then extending this to a specific protocol, say FTP (typical port 21), can I change it such that the server uses port 69, but the client uses port 100? And similarly, for Remote Desktop in WinXP (typical port 3389), i know how to change the server port to be something other than 3389, but how does one change what port the client uses (if at all possible)?

  Read the article

• Creating New WebSphere cluster

  - by user154561

  I need to improve WAS perfomance and want to make cluster. I have two separate machines with WebSpphere 7 on it. As I see to do this, I need to add node from my second (remote) WAS to the first one. I try to use "Add node" from console, but without success. It can't find host when I try to execute it. WAS help says about host: Specifies the host name or IP address of the node to add to the cell. A WebSphere Application Server instance must be running on this machine. Does that mean that I cannot add node from a remote machine with "add node?"

  Read the article

• Network Monitoring Tool Recommendation

  - by user42801

  Hello, My company is looking for a monitoring app/tool that would allow us to capture and graph statistics on network performance. As a starting point, we would like to ping remote host(s) and gateway(s) from several of our servers, grab an average of the ping times from each of our servers to the remote host(s), and then graph it (preferably in a central location). Also, we would like to be able to graph the results for time frames as short as a week to as long as 6 months. It is reasonable to expect that we would ask more of the selected monitoring app/tool as we come up with other key network performance indicators in the future. So an app with great flexibility and features would be ideal. Upon first glance, Cacti looks like it might be a fit. Any other recommendations? Thanks in advance for any input.

  Read the article

• Cannot SSH anymore, what went wrong?

  - by lbwtz2

  I use to ssh to a remote server (no rsa-key, just password). Now the server do not accept the connection any more and throw me this error: ssh_exchange_identification: Connection closed by remote host While I can google a little to find a fix I can't figure out what went wrong since I haven't touched anything on the machine since last login. Can you help me find the cause? EDIT: Inspecting the logs I've found these: /var/auth.log /var/log/auth.log:Dec 26 16:40:32 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 26 16:41:05 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 26 16:43:47 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 27 03:20:06 vps sshd[15567]: error: fork: Cannot allocate memory /var/log/auth.log:Dec 27 16:15:02 vps sshd[15567]: error: fork: Cannot allocate memory And in the same span-time I've also found a lot of these: /var/log/auth.log:Dec 26 13:00:01 vps CRON[1716]: PAM unable to dlopen(/lib/security/pam_unix.so): libcrypt.so.1: cannot map zero-fill pages: Cannot allocate memory /var/log/auth.log:Dec 26 13:00:01 vps CRON[1716]: PAM adding faulty module: /lib/security/pam_unix.so What are these?

  Read the article

• Mail Stuck in Backend Exchange Queue

  - by Kyle Brandt

  I have a message that has and is stuck in a queue on my backend mail server. The queue is: Internet Mail SMTP Connector (MY_FRONT_END_SERVER_NAME)-524350ff... It is in state retry with 183 failures. It is only one message and all other mail is flowing. The message is not particularly large. My limited understanding, a guess really, is that this message should get handed off to the front end mail server and sent to the remote hosts for which it is destined, so it should even matter if the remote host is up. However, I can telnet to the smtp provider of that host. How can I find out why it is stuck in this queue, and can I force it out somehow (unfreeze doesn't help me)?

  Read the article

• How can I view my video card's temperature via SSH?

  - by NT3RP

  I've finally managed to set up my two ATI Radeon 6950 video cards in my machine, but the cards can get quite hot. Based on the arrangement of my apartment, I want to be able to SSH into the machine an execute a command to find out the temperature. What I have tried so far is this... export DISPLAY=:0.0 sudo aticonfig --adapter=0 --od-gettemperature However, when I do that via SSH, I get the following error: ERROR - X needs to be running to perform ATI Overdrive(TM) commands If I turn on X forwarding when I remote into the machine, then it just seems to affect my local machine instead of the remote machine. Am I doing this correctly? Is there a better way to monitor my video card's temperature?

  Read the article

• Uploading to another domain gives HTTP code 405

  - by dragon112

  I'm trying to upload a file (which can be quite large) from the website of one server to the backend of another server using plupload. Lets say: domain 1 = http://www.websitedomain.com/uploadform domain 2 = http://www.backenddomain.com/uploadhandler Trying to upload i send the following: OPTIONS /main/uploadnetwork.php HTTP/1.1 Host: backenddomain.com Connection: keep-alive Access-Control-Request-Method: POST Origin: http://www.websitedomain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.79 Safari/537.4 Access-Control-Request-Headers: origin, content-type Accept: */* Referer: http://www.websitedomain.com/uploadform Accept-Encoding: gzip,deflate,sdch Accept-Language: nl-NL,nl;q=0.8,en-US;q=0.6,en;q=0.4 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 DNT: 1 But when I try to start the upload the server returns the following: HTTP/1.1 405 Method Not Allowed Allow: GET, HEAD, OPTIONS, TRACE Content-Type: text/html Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET X-Powered-By-Plesk: PleskWin Date: Mon, 01 Oct 2012 12:41:57 GMT Content-Length: 999 After doing some research I found out that a browser does this to check if the server will accept the intended message. It looks like my server doesn't feel like accepting a simple POST call even tho i use post all the time. The Google Chrome console gives the following error: XMLHttpRequest cannot load http://www.backenddomain.com/uploadhandler. Origin http://www.websitedomain.com is not allowed by Access-Control-Allow-Origin. Does anyone know how to stop the browser from checking or how i can tell my server to just accept the POST?

  Read the article

• How to fix windows new line character on sftp synchronization in eclipse (pdt)

  - by superspace

  Hello, I have a problem with windows new line characters being introduced into text files on eclipse sftp synchronization (via jcraft's sftp plugin). I've set "New text file line delimiter" to Unix and have even sanitized the file with "fromdos" but every time i upload using the sftp plugin, windows new line characters can be seen in the remote file as "^M" characters (when viewed in vi). A point to note is that if i upload using an external sftp client, it's all fine. Eclipse Version: PDT (Helios) SFTP: jcraft sftp plugin Local Environment: Ubuntu 10.04 Remote Environments: FreeBSD 6.4, Debian 4.0 What am i missing? My co-workers would thank you for the solution :) Thanks in advance.

  Read the article

• Netbeans automatically changes the file owner when updating files

  - by Alon_A

  We use Netbeans IDE 7.2 to edit our PHP files. In the Run Configuration it is configured as Remote Web Site to automatically save the changes on our web server (Centos OS 6.3). The problem is that every time it is updating the files the owner of the file is changed from apache:apache to userThatUploadedTheFile:users. This causes us problems with SOAP cache files that are configured with apache:apache ownership, and we need to manually chownit back to apache:apache. We've checked the "Preserve Remote File Permissions" checkbox, so the permissions are not changed, only the owner. Is there any solution to preserve the ownership ?

  Read the article

• Permissions Issue with Files Generated by PerfMon

  - by SvrGuy

  We are trying to implement some data logging to CSV files using a Data Collector Set in PerfMon (on a windows Server 2008R2 system). The issue we are running into is that we (seemingly) can't control the permissions being set on the log files created by perfmon. What we want is for the log files created by perfmon to have Everyone:F permissions (Full Control for Everyone). So, we have a directory structure setup where all logs go into a folder: c:\vms\PerfMonLogs\%MACHINENAME% (e.g. c:\vms\PerfMonLogs\EvaluationG2) In the above example, c:\vms\PerfMonLogs\EvaluationG2 has permissions Everyone:F (below is the icacls for this directory) EVALUATIONG2/ Everyone:(OI)(CI)(F) NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) When the data collector set runs, it creates new sub folders and files within c:\vms\PerfMonLogs\EvaluationG2, e.g. (C:\vms\PerfMonLogs\EVALUATIONG2\M11d26y2012N3) Each of these directories and files has the following permissions: M11d26y2012N3 NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) So these new folders and not simply inheriting permissions from the parent folder (don't know why). Now, we tried adding Everyone:F using the security tab on the collector set (No dice). Any ideas? How do we control the permissions on the log files generated by perfmon data collector set?

  Read the article

• How do I get the current date according to an NTP server without setting it locally?

  - by Zac B

  I want to get the current date and time according to a remote NTP server, using Linux. I don't want to change the local time as a result; I just want to get the remote date, adjusted for the local time zone, printed out. The date returned must comply with the following criteria: It needs to be reasonably accurate. It needs to be adjusted for the timezone on the local system making the request. It needs to be formatted in an easily-readable or interpretable way (standard date format, or seconds since epoch). What I've Tried: I can call ntpdate -q my.ntp.server and get the offset between the local time and the server's time, but that doesn't return the date according to the NTP server; it just returns the offset and the local date. Is there some easy way/command I can use to say: "Print out the date according to a given NTP server, adjusted for my current timezone"?

  Read the article

• Publish database between two open database connections (Visual Studio 2005)

  - by danielswe

  I have two data locations, one to a local and one to a remote database. How do I copy the local database schema to the remote? The reason I don't use "Publish to provider" is that I'm not sure that I have all the information necessary to do so. I have the database name, server, username and pass but not "web service address" nor "web service password". I work in Visual Studio 2005. The server is a MSSQL 2005 server. I have tried using the queries but I only get errors doing so.

  Read the article

• Trouble running multiple Firefox versions on OS X Lion

  - by politicus

  I am trying to use two versions of Firefox (11 and 13) on OS X Lion. I don't especially want to run two versions at the same time. I want to be able to run the version 11 when I choose the version 11 via the profile manager. The same for the version 13. Every time, I want to launch the version 11, the launcher launches the version 13... When I select the version 11 via the profile manager, Firefox 13 is launched. I created 2 automators apps (FF11.app and FF13.app) to launch Firefox : /Applications/Firefox11.app/Contents/MacOS/firefox-bin -no-remote -P FF11 & /dev/null & /Applications/Firefox13.app/Contents/MacOS/firefox-bin -no-remote -P FF13 & /dev/null & Any help would be greatly appreciated. Thanks in advance.

  Read the article

• network path not found error on creating schtasks

  - by user50273

  I am getting "ERROR: Network path was not found" when I try to create a scheduled task on my local machine. I am using this command at the command prompt: schtasks /tn taskname /tr taskpath /sc minute /mo 20 /sd 09/23/2010 /s \\%computername% /u username /p password When I give the above command without computername, username and password the task gets created perfectly fine. What am I doing wrong?? EDIT : I got it working by using the below command. I do not understand why it is working becuase I am using /ru and /rp which are remote user and remote password settings whereas I am executing the command on my local machine. And I had to give double quotes to computername. schtasks /tn taskname /tr taskpath /sc minute /mo 20 /sd 09/23/2010 /s "%computername%" /ru username /rp password

  Read the article

• Pushing Large Files to 500+ Computers [closed]

  - by WMIF

  I work with a team to manage 500-600 rented Windows 7 computers for an annual conference. We have a large amount of data that needs to be synced to these computers, up to 1 TiB. The computers are divided into rooms and connected through unmanaged gigabit switches. We prepare these computers ahead of time with the Windows installation and configuration, plus any files that we have available to us before we send the base image in for replication by the rental company. Every year, we have presenters approach on site with up to gigs of data that need to be pushed to the room that they will be presenting in. Sometimes they only have a few files that are small sizes, such as a slide PDF, but can sometimes be much larger 5 GiB. Our current strategy for pushing these files is using batch scripts and RoboCopy. For the large pushes, we actually use a BitTorrent client to generate a torrent file, and then we use the batch-RoboCopy to push the torrent into a folder on the remote machines that is being monitored by an installed BT client. Often times, this data needs to be pushed immediately with a small time window. We have several machines in a control room that are identical to the machines on the floor that we use for these pushes. We occasionally have a need to execute a program on the remote machines, and we currently use batch and PSexec to handle this task. We would love to be able to respond to these last minute pushes with "sorry, your own fault", but it won't happen. The BT method has allowed us to have a much faster response time, but the whole batch process can get messy when there are multiple jobs being pushed. We use Enterprise Ghost for other processes, and it doesn't work well in this large of scale, plus it is really quite expensive for a once-a-year task like this. EDIT: There is a hard requirement that the remote machines on the floor are running Windows. The control machines do not have a hard OS requirement. I would really like to stay away from Multicast because of complications with upstream routers. Is Multicast or BitTorrent the better way to go on this? Is there another protocol that might work better?

  Read the article

• Tomcat and HTTPS connect timeout (local Proxy resolves it)

  - by smas

  I have web application on the Tomcat with webservices. I've noticed that all web services connected to https get timeout. I run this app on my localhost in my company. When I redirect all my connections through Fiddler (local proxy) everything works correctly. I don't want to execute fiddler all the time. my computer -> [FIDDLER local proxy] -> [remote proxy] // WORKS my computer -> [remote proxy] // timeout How to increase tomcat logging to get more technical logs than only "timeout". Is there any other way to get more information what blocks the https URL?

  Read the article

• Unable to SSH into ESXi 4.1 host - "Access Denied"

  - by Andrew White

  I am unable to SSH into an existing ESXi server. I have a user which is in the "root" and "users" group and is able to connect via vSphere. However after enabling "Remote support (SSH)", attempting to connect by putty and entering my username/password when prompted I am presented with an "Access Denied" message. I have run through the options presented at this KB article to no avail. I have taken down the firewall on the machine (it is remote) temporarily to check if this helped - no change. The username/password are definitely correct and I can obviously get connectivity if I am presented with the username/password prompt. I am at a bit of a loss what else I can try. Thanks all

  Read the article

• Confused with creating an ODBC connection, apparently I have two separate odbcad32.exe files?

  - by Hoser

  Alright, this is my first time working with this so forgive me if I'm a little confusing or vague. I have a server with Windows Server 2008 Standard without Hyper-v (6.0, Build 6002). I'm running a small website off this server and using a Microsoft Access database to store some information coming in through the website. I'm sure the PHP I have written to open the ODBC connection is correct as it has worked for me when I created this website in a testing environment on a laptop. My current issue now is that it seems like I have two different odbcad32.exe's, and one doesn't appear to have a driver for a .accdb file, and only a .mdb file. The other has a driver for both. The first one I speak of has a driver titled 'Driver do Microsoft Access (.mdb)', the second one has a driver titled 'Microsoft Access Driver (.mdb, .accdb)'. I access the first odbcad32.exe by going to C:\Windows\SysWOW64\odbcad32.exe, and then the one that seems to have the driver I need I go to Control Panel-Administrative Tools-Data Sources(ODBC) and simply create a new connection in the System DNS tab. Whenever I make changes to the one that I access through the Control Panel, I see no changes, however if I use the odbcad32.exe file in SysWOW64 I do get some changes in the errors that come back to me. The main difference I noticed is that when I set up an ODBC connection with the Control Panel method it said it simply couldn't find the ODBC connection, but when I made a .mdb connection in the SysWOW64 one (and pointed it to a .accdb file) it says Cannot open database '(unknown)'. It may not be a database that your application recognizes, or the file may be corrupt. Which makes it seem like it is this odbcad32.exe version in SySWOW64 that is being recognized as the 'correct' one. Is there any way to fix this? I've tried to be as thorough as possible but if I've been confusing or left anything out let me know.

  Read the article

• How can I get mouse capture to work in virtualbox when I move guest window to second monitor?

  - by Dan

  I'm running VirtualBox on a Win7 host. Guest OS is Centos. My setup is a laptop (screen 1) with a huge external monitor (screen 2). I'm only telling Centos there is one monitor though. When I start up VirtualBox on screen 1, the mouse capture works fine. I don't have mouse integration because (I think) the kernel on Centos is too old to support it. That's fine, I don't mind doing the Right-Control thing. The problem I have is that when I drag the whole VM window over to my second monitor, the mouse capture doesn't work right anymore. I click inside the VM and can move the VM cursor a little bit, but I can't always get to the edges of the VM screen -- before I get all the way to an edge, the cursor will escape from the VM as if I had hit right-control. But it's still captured according to the icon, and if I then hit right-control, the guest cursor jumps to a different screen location. My workaround: if I have the VM window mostly on screen 2, but a small corner of it still on screen 1, then the mouse capture works correctly. Is there a setting to make this work better?

  Read the article

• Random TCP Resets

  - by allenwei

  We got randomly TCP "reset" error when we send request to remote server. Log from remote server Cisco TCP Connection Terminated,Nov 05 14:43:39 EST: %ASA-session-6-302014: Teardown TCP connection 640068283 for Outside:xxxx to xxxx duration 0:00:00 bytes 4160 TCP Reset-O One my local machine I saw when I use netstat 100703 connections reset due to unexpected data 324186 connections reset due to early user close I also use tcpdump to see what's wrong with it, I saw xxxx.https: Flags [R.], seq 290, ack 1369, win 136, options [nop,nop,TS val 2871790533 ecr 1897173283], length 0 The problem just happened today, we didn't change anything on our server. Anyone know what's wrong with it? Is it related to code we wrote send out request or related to linux configuration?

  Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >