Search Results

Search found 23783 results on 952 pages for 'edit and continue'.

Page 398/952 | < Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >

• Slow disk transfer rate

  - by Nooklez

  I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

  Read the article

• Managing ip6tables (or an alternative firewall) remotely

  - by Matthew Iselin

  I'm working with IPv6 and have run into an issue configuring ip6tables on our main router in order to control what can come into the network. A default DROP rule in the FORWARD section has worked well (obviously leaving ESTABLISHED,RELATED as ACCEPT) to keep internal clients' open ports from being accessed. However, running an ip6tables command for every little change is unwieldy. Whilst we are able to continue creating rules manually, I'm wondering if there's some sort of management interface we could use to create the rules quickly and easily. We're looking to be able to save time working on our firewall as well as providing a simple method for modifying rules for those who will eventually replace us. I know webmin (heavily locked down on our network, naturally) has support for modifying iptables rules, but seemingly no support for ip6tables. Something similar would be fantastic. Alternatively, suggestions for a firewall solution apart from iptables/ip6tables which can be managed remotely wouldn't be out of order. A web interface for management is certainly preferable, even if it is just a wrapper with shiny buttons over the raw config files.

  Read the article

• rsnapshot schedule overlapping, help with backup schedule

  - by Znarkus

  Hello, I have to following configuration. rsnapshot.conf interval halfhourly 4 interval hourly 6 interval twohourly 12 interval daily 7 interval weekly 4 crontab 0,30 * * * * /usr/bin/rsnapshot halfhourly >> /var/log/rsnapshot.halfhourly.log 2>&1 5 * * * * /usr/bin/rsnapshot hourly >> /var/log/rsnapshot.hourly.log 2>&1 10 */2 * * * /usr/bin/rsnapshot twohourly >> /var/log/rsnapshot.twohourly.log 2>&1 15 3 * * * /usr/bin/rsnapshot daily >> /var/log/rsnapshot.daily.log 2>&1 20 6 * * MON /usr/bin/rsnapshot weekly >> /var/log/rsnapshot.weekly.log 2>&1 Only halfhourly is running correctly now. hourly spits out this error: rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: Lockfile /var/run/rsnapshot.pid exists and so does its process, can not continue To me it seems like my 5 min space between halfhourly and hourly is too small. Is this configuration crazy? I like having backups every thirty minutes, that will probably save my ass some day. Please help me make a decent backup schedule, that doesn't clog up the system, but creates frequent enough backups. Thank you.

  Read the article

• Adobe premiere CS5 problem with the display driver

  - by user30179

  This error is really hindering our project. I get an error, it started showing-up June 16th 2010. There are no windows updates at the on the same date as the error, other than (Windows Defender) Seems to happen when working with Image overlays. ERROR: "The NVIDIA OpenGL driver detected a problem with the display driver and is unable to continue. The application must close." We opened the side of the case in the possibility there is an over heating problem. Nvidia Driver ver 8.16.11.9175 (nVidia Quadro FX 1700) I am running: Windows 7 x64 Adobe premiere CS5 Production nVidia Quadro FX 1700 (MRGA14L) 4 Gig ram RAID 10 2 750GB drives Duo core 3.0 6MB L2 Cache This is at least three other people that have come across this error: NVidia Forum EVGA Forum NVidia Forum UPDATE: Having the case open did not help. I also installed New Nvidia drivers now I get a different error: *ERROR:*Your hardware configuration does not meet minimum specifications needed to run the application. The application must close. I ran Windows Update and installed all four updates so now I am waiting to see if the error occurs again. Anything beyond this I am out of options.

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• System recognizes admin password on the Welcome screen but not when elevating

  - by Lee C.

  I set up Windows 7 with a couple of standard accounts, and an administrator account (called Odin). I can log in to Odin just fine from the Welcome screen. While logged into Odin I can do anything that requires administrator privileges without a password: just hit Yes in the User Account Control dialog. If I am logged into one of the other accounts and I do something that requires elevation (e.g. most installers, and some control panel functionality), then Windows presents me with a User Account Control dialog asking "Do you want to allow the following program to make changes to this computer? To continue, type an administrator password, and then click Yes." The account shown in this dialog is Odin, so I enter Odin's password. But Windows redisplays the dialog with the message "Logon failure: unknown user name or bad password." This always happens, and has done so for many months, probably since I first got the computer. Why does Odin's password work from the Welcome screen, but not when elevating? Please note that I am not asking how to recover Odin's password. I remember the password I originally set for Odin, and it works as it should from the Welcome screen, but is not recognized when elevating. The password has no funny characters, just letters and digits. Thanks!

  Read the article

• Team Foundation Server 2008 - TF220056 Error during installation

  - by David

  I'm attempting to install Team Foundation Server 2008 on a Windows Server 2003 instance that exists under Hyper-V. The SQL Server database itself is held on the root partition of the Hyper-V server and has the Reporting Services installed (so I've solved the TF220059 error already). After hitting "Next " after typing the name of the SQL Server I get this error: --------------------------- Microsoft Visual Studio 2008 Team Foundation Server Setup --------------------------- TF220056: An unrecoverable error occurred while trying to check the status of the Team Foundation database. Installation cannot continue. Check the install log for more details. --------------------------- OK --------------------------- The error log's stack trace makes it look like a bug in the TFS installer itself: [03/22/10,19:14:42] TFSUI: [2] tfsdb.exe: System.IO.IOException: The directory name is invalid. [03/22/10,19:14:42] TFSUI: [2] tfsdb.exe: at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath) [03/22/10,19:14:42] TFSUI: [2] tfsdb.exe: at System.IO.__Error.WinIOError() [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe: at System.IO.Path.GetTempFileName() [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe: at Microsoft.TeamFoundation.DatabaseInstaller.CommandLine.Commands.InstallerCommand.get_Log() [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe: at Microsoft.TeamFoundation.DatabaseInstaller.CommandLine.Commands.InstallerCommand.Run() [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe: at Microsoft.TeamFoundation.DatabaseInstaller.CommandLine.CommandLine.RunCommand(String[] args) [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe: The directory name is invalid. [03/22/10,19:14:43] TFSUI: [2] tfsdb.exe check failed with error code: 100 I'm running the installer as the domain Administrator, although the server is a Terminal Server in Application Mode, might that be the cause of the problems?

  Read the article

• installing Conkeror on Ubuntu 12.04

  - by Menelaos Perdikeas

  I am reading the instructions on conkeror site (and elsewhere) on how to install conkeror on Ubuntu (I am using Ubuntu 12_04 LTS) and it seems that the correct sequence is: sudo apt-add-repository ppa:xtaran/conkeror sudo apt-get update sudo apt-get install conkeror conkeror-spawn-process-helper The first step (apt-add-repository) seems to execute without a problem, giving the following output: You are about to add the following PPA to your system: Conkeror Debian packages for Ubuntu releases without xulrunner (i.e. for 11.04 Natty and later) More info: https://launchpad.net/~xtaran/+archive/conkeror Press [ENTER] to continue or ctrl-c to cancel adding it Executing: gpg --ignore-time-conflict --no-options --no-default-keyring --secret- keyring /tmp/tmp.Re7pWaDEQF --trustdb-name /etc/apt/trustdb.gpg --keyring /etc/apt/trusted.gpg --primary-keyring /etc/apt/trusted.gpg --keyserver hkp://keyserver.ubuntu.com:80/ --recv CB29CBE050EB1F371BAB6FE83BE0F86A6D689050 gpg: requesting key 6D689050 from hkp server keyserver.ubuntu.com gpg: key 6D689050: "Launchpad PPA for Axel Beckert" not changed gpg: Total number processed: 1 gpg: unchanged: 1 However, the apt-get update seems unable to fetch packages from the newly added PPA, with its output ending in: Hit http://security.ubuntu.com precise-security/restricted Translation-en Hit http://security.ubuntu.com precise-security/universe Translation-en Err http://ppa.launchpad.net precise/main Sources 404 Not Found Ign http://extras.ubuntu.com precise/main Translation-en_US Err http://ppa.launchpad.net precise/main i386 Packages 404 Not Found Ign http://extras.ubuntu.com precise/main Translation-en Ign http://ppa.launchpad.net precise/main Translation-en_US Ign http://ppa.launchpad.net precise/main Translation-en W: Failed to fetch http://ppa.launchpad.net/xtaran/conkeror/ubuntu/dists/precise /main/source/Sources 404 Not Found W: Failed to fetch http://ppa.launchpad.net/xtaran/conkeror/ubuntu/dists/precise/main/binary-i386/Packages 404 Not Found E: Some index files failed to download. They have been ignored, or old ones used instead. Accordingly, apt-get-install conkeror fails with: mperdikeas@mperdikeas:~$ sudo apt-get install conkeror Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package conkeror Any ideas what might be wrong ?

  Read the article

• Windows 7 sometimes boots in VGA mode

  - by TuxRug

  I have an Asus G50VT-x5 laptop with nVidia GeForce9800M-GS graphics. Normally, Windows boots normally, but about 20% of the time (rough estimate), it will boot with the fallback VGA driver, maxing out at 800x600 with no Aero. I've checked the system logs and there is nothing indicating an error loading the nVidia driver. It even specifies in the logs that the Nvidia Display Driver service started successfully, even though it has booted in safe graphics mode. This has been happening for a while, but it's happening a little more often now than it was before. Since the first time my system exhibited this behavior, I have updated my graphics driver a handful of times. I used System Information for Windows to check for problems there, but the only thing that stood out was the following: Core Temperature 4486449 °C (8075639 °F) Shaders Temperature 1171513530 °C (2108724330 °F) I know this reading is incorrect, because my laptop is nowhere near the surface of the sun and my desk has not burst into flames. When it's opererating normally, I get a sane reading like [Core Temperature 58 °C (136 °F)] with no Shaders Temperature listed. All I have to do to resolve the issue is reboot. I have seen no stability issues with the graphics or anything else. A long time ago, I had an issue with this computer where my framerate would suddenly drop during a 3D game from 40fps to <1fps, but after looking at the temperature readout immediately after quitting a game, I removed the bottom panel and blew the dust out of the vent and heatsink. Since then I have no drops in framerate under any situation. I have uploaded a zip containing the SIW reports for when the problem is occurring and when the computer is operating normally. I don't have a paid account so it can only be downloaded 10 times, so please only download the reports if you think you can use them. If you try to download the reports and they are no longer available, please comment and I will re-upload them. If you want to look at the files, they are on Rapidshare. EDIT It happened again, and I looked a little deeper into the System logs. When this happens, there are a lot of errors about other device drivers unable to start. All of these errors are for PnP drivers. Also, my USB keyboard and mouse take a few moments before they actually start working, although this happens sometimes the first normal boot as well. I am quite sure this is related, so I am adding the pnp tag. Also, CHKDSK will not run on boot. Even if a check is scheduled or a volume is manually set as dirty, CHKDSK will be skipped entirely, not even leaving an entry in the System logs. I tried running CHKNTFS /D, which did not work. I then manually changed my HKLM\System\CurrentControlSet\Control\Session Manager BootExecute value to the default listed on Microsoft's website. That did not work either. I ended up booting to repair mode and running CHKDSK there, which found a number of minor inconsistencies on my system drive, but none on my data drive. I have no idea if this is related. Some more information for those who don't download my SIW report file: Antivirus and Firewall are ESET Smart Security I have three different virutalization programs installed: VMware Player, Windows Virtual PC, and VirtualBox. The network adapters for these show up in the log of failed device starts. EDIT 2 I tried running sfc /scannow, which reported that it found corrupted files that could not be fixed. The CBS log is extremely cryptic. I tried booting to my install disk, launching repair mode, and doing an offline sfc from there, which produced the same result.

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• Remote management interface for managing ip6tables (or an alternative firewall)

  - by Matthew Iselin

  I'm working with IPv6 and have run into an issue configuring ip6tables on our main router in order to control what can come into the network. A default DROP rule in the FORWARD section has worked well (obviously leaving ESTABLISHED,RELATED as ACCEPT) to keep internal clients' open ports from being accessed. However, running an ip6tables command for every little change is unwieldy. Whilst we are able to continue creating rules manually, I'm wondering if there's some sort of management interface we could use to create the rules quickly and easily. We're looking to be able to save time working on our firewall as well as providing a simple method for modifying rules for those who will eventually replace us. I know webmin (heavily locked down on our network, naturally) has support for modifying iptables rules, but seemingly no support for ip6tables. Something similar would be fantastic. Alternatively, suggestions for a firewall solution apart from iptables/ip6tables which can be managed remotely wouldn't be out of order. A web interface for management is certainly preferable, even if it is just a wrapper with shiny buttons over the raw config files.

  Read the article

• What is the best VM for developing WPF apps from within OS X?

  - by MarqueIV

  All of my machines are Macs (Mac Pro, MacBook Pro, MacBook Air and Mac Mini (and Apple TV 2.0 too! :) ) but for my day-job, I develop .NET/WPF applications. Normally I just boot into Boot Camp and develop that way, which of course works great, but there are times when I need to simultaneously get to things on my Mac-side of the equation, so I've bought both VMware 3.1 and Parallels 6. Both work, however, even on my Mac Pro where I paid to upgrade to the better video cards (the NVidia 8600s I think vs. the stock ATI cards) the WPF performance bites!! Now this confuses me since both boast that they support not only hardware-accelerated OpenGL 2.1, but also hardware-accelerated DirectX 9 (VMware even allegedly supports DirectX 10!) via their respective virtual drivers and both can run 3D games just fine, even in a window. But even the simple act of resizing a WPF window that has a tiled background results in some HIDEOUS repainting and resizing behaviors. It's damn near closer to what you'd expect over RDP let alone a software-only renderer (forget accelerated hardware completely!) So... can anyone please tell me WTF WPF is doing differently? More importantly, how can I speed up the WPF performance? Should I switch to VirtualBox that also has support for DirectX? Or am I just gonna have to 'byte' the bullet (sorry... had to. So I like puns! Thank Jon Stewart!) and continue using Boot Camp?

  Read the article

• ssh without password does not work for some users

  - by joshxdr

  I have a new RHEL4 Linux box that I am using to copy data to old Solaris 2.6 and RHEL3 Linux boxes with scp. I have found that with the same setup, it works for some users but not for others. For user jane, this works fine: jane@host1$ ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/osborjo/.ssh/identity debug1: Offering public key: /mnt/home/osborjo/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: read PEM private key done: type RSA debug1: Authentication succeeded (publickey). for user jack it does not: jack@host1 ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/oper1/.ssh/identity debug1: Offering public key: /mnt/home/oper1/.ssh/id_rsa debug1: Authentications that can continue: publickey,password,keyboard-interactive I have looked at the permissions for all the keys and files, they look the same. Since I am using home directories mounted by NFS, the keys for both the remote host and the local host are in the same directory. This is how things look for jane: jane@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jane operator 394 Jan 27 16:28 authorized_keys -rw------- 1 jane operator 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jane operator 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jane operator 1205 Jan 27 16:46 known_hosts For user jack: jack@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jack engineer 394 Jan 27 16:28 authorized_keys -rw------- 1 jack engineer 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jack engineer 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jack engineer 1205 Jan 27 16:46 known_hosts As a last ditch effort, I copied the authorized_keys, id_rsa, and id_rsa.pub from jill to jack, and changed the username in authorized_keys and id_rsa.pub with vi. It still did not work. It seems there is something different between the two users but I cannot figure out what it is.

  Read the article

• X.org - mouse gets stuck on press

  - by grawity

  I'm using Arch Linux. Very often, when I click on something, the OS thing sees the mouse press but not the release. If it was a link or file I clicked, moving the cursor would drag it too. Hammering the same mouse button again gives no effect. Usually, if I tap the touchpad (ALPS), the system finally sees both press and release of that, and I can continue working. (This might be because it uses a different driver - synaptics instead of evdev.) As you can imagine, this is quite annoying even for someone who spends 70% of his life in front of a terminal app. This is not a mouse issue - I'm on a laptop, and this affects both the Trackpoint thing and an external USB mouse. This is not a DE or window manager issue - I have used GNOME (with Metacity, Compiz and Xfwm4), Xfce (with Metacity and Xfwm4), mwm, twm, awesome, and wmii. Doesn't seem to be a hardware thing - after rebooting into Windows XP, everything works fine. hal is used for the auto-configuration of devices (as I have to disconnect the USB mouse often), so Xorg.conf really has nothing of relevance. Xorg -version shows: X.Org X Server 1.6.3.901 (1.6.4 RC 1) Release Date: 2009-8-25 X Protocol Version 11, Revision 0 If it changes anything, the laptop is stone-age Dell Latitude C840. I kinda suspect either hal or the evdev thing to cause it, but I really have no ideas on what to check further. In other words, HALP!#$ This thing is driving me nuts.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• Merging cuesheet chapter halves into single track for an audiobook

  - by TheSavo

  I have an audiobook that I have ripped and I need some help constructing chapters. I have already made some cue sheets TITLE "Bookname" PERFORMER "the Author" FILE "File1.FLAC" wave ; 23971906.667 milliseconds TRACK 01 AUDIO TITLE "_Intro" INDEX 01 00:00:00 TRACK 02 AUDIO TITLE "CH 01" INDEX 01 24:15:50 TRACK 03 AUDIO TITLE "CH 02" INDEX 01 66:21:00 TRACK 04 AUDIO TITLE "CH 03" INDEX 01 87:05:00 The audio book is in two files. The chapter at the end of the first file is continued in the second file. However, the second file restates: The publisher Book Title List item Blah blah blah I would like to merge the two 'halves' of the chapter in one seamless track. The only way I can think to do this would be be: Bulk cut down the tracks. Drop the junk info into junk track Continue the track listings as normal Take the two "halves" of the target chapter and build a separate cue sheet for it. I know there has to be an easier way. I am ok with making the 'junk' info a 'gap' or something. These are are FLAC files that will be converted to MP3 for my phone and other potable devices. I have read the primers on cue sheets, but I am just not getting it.

  Read the article

• My New Dell Workstation T-7500 gives electric shock

  - by Dan

  Just bought Dell T-7500 Workstation. When installation technician came to Install the workstation, he got an electric shock when he touched the Start Button. He also got shock when he touched Front Panel. No shock when touching rest of the Chassis. He called Dell Support & tried to troubleshoot by taking out various wires etc but did not help. I touched the same places & I also got shock. We checked everything possible including connecting to various outlets but it didn't solve the problem. Installation subcontractor said that they are not supposed to troubleshoot anything on new system, just install it & they made notes & left. I called my sales guy & it was weekend so he said he will take care of it on Monday. Here are my concerns : (1) Why does that happen ? Although it is a mild shock & it won't kill you but might damage other parts of workstation ? (2) Is this common for workstations ? (3) What should I do ? Of course Dell will try to troubleshoot again but should I let them do that OR ask for a New System ? (4) Wheat would happen if I continue using it till the new system arrives ? Thank You.

  Read the article

• Set up lnux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project The above upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Create a chroot jail to hold sftp user via rssh. This will force SCP/SFTP and will circumvent traditional FTP server setup. #cd /tmp #wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm #rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm #useradd -m -d /home/dev -s /usr/bin/rssh dev #passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. #vi /etc/rssh.conf Uncomment line allowscp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). Above instructions for SFTP appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Transparent proxy which preserves client mac address

  - by A G

  I have a customer that wants to intercept SSL traffic as it leaves their network. My proposed solution is to setup a proxy that is transparent and both layer 2 and layer 3 so it can simply be dropped into their network without any change in config required. The proxy has two NICs, one connected to the server, the other to the client. The client, proxy and gateway are under control of the customer, the server is not. For example: client --- Proxy --- gateway -|- server I have my proxy program configured with IP_TRANSPARENT socket option to it can respond to connections destined for a remote IP. I am using the following setup: iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 3128 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1 ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 The client in question is on its own subnet and has been configured so that the proxy is the default gateway. The result is: Client sends a frame to the proxy; source IP is client, source mac is client, destination IP is server, destination mac is proxy Proxy forwards this frame to the gateway; source IP is proxy, source mac is proxy, destination IP is server, destination mac is gateway Gateway forwards this to the server and gets a response back. Gateway sends reply back to proxy; source IP is server, source mac is gateway, destination IP is proxy, destination mac is proxy Proxy forwards this reply to client; source IP is server, source mac is proxy, destination IP is client, destination mac is client. The tproxy and iptables configuration lets the proxy send packets with a non local ip address. Is there a way to make something transparent at the mac address level? That is, put the client on the same subnet as the gateway. The gateway sees the source IP and mac as that of the client, even though they originated from the proxy. Could this be done by configuring the proxy as a bridge then use ebtables to escalate the traffic to be handled by iptables? When I use ebtables to push something up to iptables, it appears my proxy program doesn't respond to the packets as they are destined for the gateways's mac address, not the proxy's. What are some other potential avenues I could investigate? EDIT: When the client and gateway are on different subnets (and client has set the proxy as the gateway), it works as described in 1 to 5. But I want to know if it is possible to have the client and gateway on the same subnet and have the proxy fully transparent (ie client is not aware of the proxy). Thanks! EDIT 2: I can configure the proxy as a bridge using brctl, but cannot find a way to direct this traffic to my proxy program - asked here Possible for linux bridge to intercept traffic?. Currently, with the description numbered 1 to 5, it operates at layer 3; it is transparent on the client side (client thinks it is talking to the server's IP), but not on the gateway side (gateway is talking to the proxy's IP). What I want to find out is, is it possible to make this operate at layer 2, so it is fully transparent? What are the available options I should research? Thanks

  Read the article

• Video desktop recording and multiple WM displays, capturing nonactive display

  - by okobaka

  Two WM running on one local machine. WM - Fluxbox. Using ffmpeg to record desktop. ffmpeg -an -f x11grab -s 1920x1080 -r 25 -i :1.0 -sameq /tmp/video.mkv On one display everything works great, but not when i have another WM display startx -- :1. What i am doing right now is to switch ctrl+alt+f8 to display:1.0, and start recording with ffmpeg. Everything is fine until i switch back ctrl+alt+f7 to display:0.0, WM and captured video image freezes, but when i switch back ctrl+alt+f8 to display:1.0, it unfreeze and continue recording. So, how to make display:1.0 not to freeze, while on display:0.0? Tested some more. open [display 0.0] open [display 0.1] from [display 0.0] = open => [display 0.2] same problem For different users and same users results are the same. ffmpeg keeps recording that paused image. Looks like WM root window need to be active, to be recorded.

  Read the article

• RDP or SSH connection trough Windows 2008 server VPN hang after a while

  - by xt4fs

  I have been experiencing a very strange issue with our VPN setup on Windows Server 2008. That server is running as a Xen Virtual Machine. We use it for two purposes, permit our mobile workers to connect to another server hosted somewhere else that only allow that ip, and use it to RDP or ssh to many other virtual machine on the same server. The server has no performance issue and still a load of memory free. All other virtual machine has no problem whatsoever. Many of those virtual machine have public IP (web servers) and all their firewall are set to allow only ssh connection or RDP connection from their local interface. When I am connecting directly with either ssh or RDP to one of the other virtual machine everything run without any issues. However, when I am doing so through the VPN after some time the connection just hang, it usually continue after some time (5 or 10 minutes). It seems as more there is network usage more often it happen to a point where it is completely unusable. The worst thing I can do to hang it faster is to actually ping the vpn client IP from the local network, after some time the latency increase until it hang. This happen even if I do RDP to the local ip of the VPN server trough the VPN. The server report no problem and if I disconnect to the vpn and reconnect right away everything is alright. There is nothing wrong in the VPN server log. I have taught at the beginning that it could have been an issue with the Host server so I try to RDP,ssh directly to the guest and I have experience no issue while doing this, so it really seems to be a problem with the VPN server on Windows server 2008. Another very weird thing is it does not seems to be of any issue if you only do Internet (NAT) without trying to connect to any local ips.

  Read the article

• System freezes during boot process

  - by slugster

  Hi everyone, i have a machine running Win7 Ultimate. It was running fine, then it just froze - all the stuff i was doing was still on the screen, but mouse and keyboard input was ignored, any animation that was happening on the screen stopped, the machine literally just froze. So i rebooted (power off button), from then on the machine will reboot, but it ultimately freezes again. The instance when this happens will vary - i have made it as far as the Windows login screen, but mostly it will do the POST, then give me the option to press F1 to continue or Del to enter BIOS settings (but of course pressing a key has no effect - it's frozen!). I have disconnected everything not necessary for the boot process, the only peripheral that remains attached is the keyboard. (even the network cable is disconnected). Prior to this the machine was operating fine. The install of Win7 is only 2 days old, and it was a fresh reinstall (i.e. not an upgrade or repair). Can anyone give me an indication of what may be wrong here? I'm not sure if this question should be here or on SuperUser, please migrate it if i have chosen the wrong board.

  Read the article

• Supervisord doesn't stop nginx process

  - by Lennart Regebro

  I'm using Supervisor a lot, and in this project I have an nginx process managed by Supervisord. The relevant parts of the configuration is this: [supervisord] logfile=/home/projects/eceee-web/prod/var/log/supervisord.log logfile_maxbytes=5MB logfile_backups=10 loglevel=info pidfile=/home/projects/eceee-web/prod/var/supervisord.pid ; childlogdir=/home/projects/eceee-web/prod/var/log nodaemon=false ; (start in foreground if true;default false) minfds=1024 ; (min. avail startup file descriptors;default 1024) minprocs=200 ; (min. avail process descriptors;default 200) directory=/home/projects/eceee-web/prod [program:nginx] command = /home/projects/eceee-web/prod/bin/nginx redirect_stderr = true autostart= true autorestart = true directory = /home/projects/eceee-web/prod stdout_logfile = /home/projects/eceee-web/prod/var/log/nginx-stdout.log stderr_logfile = /home/projects/eceee-web/prod/var/log/nginx-stderr.log The /home/projects/eceee-web/prod/bin/nginx command will start nginx in the foreground, it does not deamonify itself. Still, stopping it will fail: supervisorctl stop nginx Will not give any answer, but the process will continue. Any idea what? This is on OS X Darwin, with Supervisor 3.0a9 and nginx 0.7.65.

  Read the article

• MySQL Server hitting 100% unexpectedly (Amazon AWS RDS)

  - by Luc

  Please help! We've been struggling with this one for months. This week we upped our RDS instance to the highest performing instance and although the occurrences have reduced, we're still having our DB all of a sudden hit 100%. It comes out of nowhere. Sometimes 2am, sometimes midday. I've ruled out a DOS - our pages access logs have normal traffic I've ruled out memcached suddenly dieing (hits and misses continue as normal). The SHOW PROCESSLIST while we have issues reports about 500 queries in queue. If I kill them off or restart the server, they just keep coming back and then eventually out of knowhere, our server resumes back to normal. Sometimes up to 3 hours. Our bad performing queries take .02 seconds to execute when the server eventually returns back to normal but while we're in this 100% CPU physco phase, those queries never finish executing. Please help!!!!! Anybody know anything about MYSQL query optimization? Could it be the server deciding to use different indexes all of a sudden, which puts it into a spiral?

  Read the article

• Exchange 2010 DAG + VMWare HA = no support?

  - by Dan

  We currently have an Exchange 2003 clustered environment (two machine cluster) that we're looking to upgrade to 2010. We recently purchased a VMWare virtualization environment (three Dell R710's with an EMC NS-120 serving up NFS datastores - iSCSI is available) that we wish to use for this new environment. I'm seeing that Microsoft does not support Exchange 2010 DAGs with a virtualization high availability solution (see links below). I would like to utilize the DAG to ensure the data stays available if one host goes down, and HA to ensure that if the physical host goes down, the VM will come back up on the other available host. Does anybody know why MS does not support this? VMWare HA will only restart the VM if it is hung/down - I don't see any difference between this and restarting the physical box if someone pulled the power... Will we only run into issues with support if it has something to do with HA/DAG failover or will they see we have HA and tell us to put it on a physical box even if it has nothing to do with HA? If we disable HA for these VM's will that satisfy them on a support case? Has anybody set up an Exchange 2010 DAG on VMware with HA enabled? Will they have any issues with using an NFS datastore? We have much greater flexibility on the EMC with NFS vs iSCSI, so I would prefer to continue utilizing that. Thanks for any input! http://www.vmwareinfo.com/2010/01/verifying-microsoft-exchange-2010.html Take a look at the second image under "Not Supported" http://technet.microsoft.com/en-us/library/aa996719.aspx "Microsoft doesn't support combining Exchange high availability solutions (database availability groups (DAGs)) with hypervisor-based clustering, high availability, or migration solutions. DAGs are supported in hardware virtualization environments provided that the virtualization environment doesn't employ clustered root servers."

  Read the article

< Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >