Search Results

Search found 11543 results on 462 pages for 'partition wise join'.

Page 398/462 | < Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• How can I remove all drivers and other files related to a USB Mass Storage device?

  - by Bob

  I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• Linux kernel - can't access sda16 & sda17

  - by osgx

  I can't access sda16 sda17 and higher partitions from my linux. This linux is rather debian (very old); kernel 2.6.23. So, I know that so old linux kernel can't access 16 partitions on single sata disk. What version of kernel should I use to be able access sda16, sda17 etc? I want to update only a kernel, not a whole Linux distribution. PS. There is an WindowsNT kernel which can access and format 16, 17 or higher partition, but my intention is to use sda16 and sda17 from linux (I want Linux Kernel). PPS: dmesg: sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 > sd 2:0:0:0: [sda] Attached SCSI disk sd 4:0:0:0: [sdb] xxx 512-byte hardware sectors ... So, there is no mapping of sda16, sda17, ... to sdb. Sdb is the second physical hard drive.

  Read the article

• Installing Debian 7.1 on FakeRAID/Intel Z77 results in boot with no grub menu

  - by user198982

  I'm trying to install Debian 7.1 from DVD onto 2x500GB drives which are set up in a FakeRAID mirror using the on-board FakeRAID provided by the Z77 chipset. I have followed the guide here https://wiki.debian.org/DebianInstaller/SataRaid. Namely, I booted into the expert install with the 'dmraid=true' option added, installed onto the RAID mirror which the installer correctly detected, then installed grub2 onto /dev/mapper/.. raid volume. I chose to use LVM (so a boot partition + LVM volume). As per the guide, I have uncommented the "GRUB_DISABLE_LINUX_UUID=true" line in "/etc/default/grub" and ran "update-grub" then "grub-install /dev/mapper/.." (with the right RAID device in the command). However, after I rebooted the system, all I got was a grub console. It did not load the menu. I checked and it seems that it never even generated a menu file. I re-installed Debian a few times since, trying out different options and also a few workarounds people posted online, but to no avail. The best I am getting is a grub console. No menu. Some times it will generate the grub.cfg, some times it won't, depending on the workaround I try. I was wondering if anyone else has experienced this issue. There is no need to preach how I should not use FakeRAID. I have seen others trying to figure this out so I think a resolution to this issue would be of interest to more than just me. Also, I first installed the system onto a small drive for testing something else. I made a backup with Acronis and was able to restore that onto the RAID mirror by using Universal Restore. When I installed it onto a 500GB without RAID, backed up using the same method, then restored onto a RAID volume of the same size, it would not boot and I got grub errors. Weird. I can post more details, just let me know what you want to see.

  Read the article

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• CentOS 6.5 new Kernel not active after reboot

  - by Kristofer

  Today I was running some yum updates and wanted to verify that everything went through fine by making sure I had a new kernel. To my surprise I noticed that CentOS was still running 2.6.32-431.5.1.el6.x86_64 even though it looked as though 2.6.32-431.23.3.el6 was installed. Indeed 2.6.32-431.23.3.el6 shows up in /etc/grub.conf but not in the upstart boot options. Any ideas why? In the update log it says: ---> Package kernel-firmware.noarch 0:2.6.32-431.5.1.el6 will be updated ---> Package kernel-firmware.noarch 0:2.6.32-431.23.3.el6 will be an update Could this be the reason? What does "will be an update" mean? My /etc/grub.conf: # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/VolGroup00-root # initrd /initrd-[generic-]version.img #boot=/dev/vda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu password --encrypted $1$auui(i$sODM4ni/Zts9IlMWu.wWF/ title CentOS (2.6.32-431.23.3.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.23.3.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.23.3.el6.x86_64.img title CentOS (2.6.32-431.5.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.5.1.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.5.1.el6.x86_64.img title CentOS (2.6.32-431.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-431.el6.x86_64 ro root=/dev/mapper/VolGroup00-root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD rd_LVM_LV=VolGroup00/swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup00/root rd_NO_DM rhgb quiet rhgb quiet audit=1 initrd /initramfs-2.6.32-431.el6.x86_64.img

  Read the article

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• Web Hosting: Any web host that supports files more than 50,000 in number?

  - by Devner

  Hi all, For my PHP & mySQL based application, I am trying to buy website hosting from a host who does not have a limit on the number of files I carry in my hosting account. Almost all the websites have a common limit of 50,000 files (some websites call it 50,000 nodes). The rest(to the extent of my search) are not even close. I have gone through the various websites, Googled lot of information, have spoken with the customer service of the hosting companies and they said that they have a limit of 50,000 files and that's why they call it the LIMIT. Now I have my application, which is a kind of social networking website, where people can upload various files of varying file size. So say if 50,000 users were to join the website and upload 1 file each, the limit of 50,000 will be reached very easily and my 50,001 customer will start facing file upload problems (& so will my account). So I would like to know if there's any website hosting services that do NOT levy such restrictions. In summary, I need the following options: No maximum file limit (more than 50,000 files in account). No maximum file upload limit in server setting (10MB, 12MB, 15MB, 20MB, etc.). Ability to upload files of various types (zip, flv, jg, png, etc.). Ability to stream Audio and Video (live audio & video not necessary). Access to .htaccess Access to php.ini, my.cnf or my.ini (this would be a plus) Supports SSL. Provides dedicated hosting(& IP) as well. Monthly payments without contracts are a plus. If you know of any such website hosting services, please post a reply ( a link to the same will be appreciated ). Thank you.

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• Windows 8 using as a webserver

  - by Jason

  I have a few hobby websites that I currently host on CentOS 6. Apache, mail serving, PHP, MySQL nothing special. In the past I used Windows XP to do this same task, for years, and I was OK. I switched to Linux and for the last few years it has been such a pain. updates break, certain apps only support certain distros without compiling from source. It prevents me from working on my hobby sites more because I am always fixing something. With Windows I locked it down, I run a hardware firewall and packet analyser, kept up on updates and A/V and never had a problem. I dont allow RDC from outside the local LAN, no FTP open, run OpenSSH on an obscure port.. I am considering switching to Windows 8 (since it is a cheaper license now that Windows 7) and running apache, HMailServer, PHP, MySQL, just like my CentOS install. My questions: I am not familiar with Windows 8, can the above be done like XP? No new security restrictions or the OS preventing this from happening? The machine is a Athlon 64-bit X2 with 32GB of RAM. Will Windows 8 see all of the RAM? Technically the machine came with Windows 7, and there is a serial number on it but I am sure I wiped away the Windows 7 recovery partition when I switched to Linux....

  Read the article

• How do I keep a table in Sync across 4 db's to be used in SQL Replication Filtering?

  - by Refracted Paladin

  I have a Win Form, Data Entry, application that uses 4 seperate Data Bases. This is an occasionally connected app that uses Merge Replication (SQL 2005) to stay in Sync. This is working just fine. The next hurdle I am trying to tackle is adding Filters to my Publications. Right now we are replicating 70mbs, compressed, to each of our 150 subscribers when, truthfully, they only need a tiny fraction of that. Using Filters I am able to accomplish this(see code below) but I had to make a mapping table in order to do so. This mapping table consists of 3 columns. A PrimaryID(Guid), WorkerName(varchar), and ClientID(int). The problem is I need this table present in all FOUR Databases in order to use it for the filter since, to my knowledge, views or cross-db query's are not allowed in a Filter Statement. What are my options? Seems like I would set it up to be maintained in 1 Database and then use Triggers to keep it updated in the other 3 Databases. In order to be a part of the Filter I have to include that table in the Replication Set so how do I flag it appropriately. Is there a better way, altogether? SELECT <published_columns> FROM [dbo].[tblPlan] WHERE [ClientID] IN (select ClientID from [dbo].[tblWorkerOwnership] where WorkerID = SUSER_SNAME()) Which allows you to chain together Filters, this next one is below the first one so it only pulls from the first's Filtered Set. SELECT <published_columns> FROM [dbo].[tblPlan] INNER JOIN [dbo].[tblHealthAssessmentReview] ON [tblPlan].[PlanID] = [tblHealthAssessmentReview].[PlanID] P.S. - I know how illogical the DB structure sounds. I didn't make it. I inherited it and was then told to make it a "disconnected app."

  Read the article

• Trouble getting started with the STEALTH monitoring package

  - by dlanced

  Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

  Read the article

• Slow RDP after server joins domain

  - by Chris Grove

  We're having RDP issues with Amazon cloud servers that we recently joined to an Active Directory domain. The setup is: A local office network A virtual private cloud in Amazon An IPSec tunnel between the two networks A number of Windows 2008 R2 servers on both networks An AD domain (call it abc.net), with one domain controller in each network. The domain controllers are both new, fresh installs. Before we had the domain set up we had local accounts for the cloud computers which were used for RDP access. Our idea was to get all of the servers on to the domain so we could use domain logins instead of per-server local logins. Before the cloud servers were in the domain, RDP (from the office network or through a VPN to the cloud) worked great. After we joined the cloud servers to the domain, RDP from the office became very slow - a few minutes to log in, long frequent pauses when the interface is unresponsive, generally just a slow and frustrating experience. This is a problem regardless of whether a domain or local login is used for RDP. Oddly, when outside of the office network and connecting to the cloud directly with the VPN, RDP is still very responsive. Any idea why RDP from office to cloud is suddenly very slow after the cloud servers join the domain? What can I look at in our configuration to address this? Any help is greatly appreciated.

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• PC dies when running at 100% CPU

  - by user155631

  I recently wrote some Java code to generate images of the Mandelbrot set (fractal). I made use of the new Fork/Join facility in Java 7 to run separate threads on all four cores (2 real, 2 virtual)simultaneously, using a large number of iterations for greater accuracy. The problem is, the process runs fine for about a minute, and then it's as if someone has pulled the plug and the PC just dies. I thought it must be the CPUs overheating, so I ran Real Temp to monitor the temperature. It's an Intel i3 processor. I can see the temperature creeping up to 70 degrees, and then it seems to level off there and run for about another 30 seconds before dying. According to Real Temp, there's still a gap of 35 degrees between the actual temperature and TJ max. I also tried disabling "CPU TM function" in the BIOS, but the problem still occurs. A colleague suggested that it might be a power supply problem, so I borrowed a more powerful PSU (can't remember what wattage it was, but it's higher than mine which is 500W). The exact same thing still happens though. Is anyone able to suggest what the problem might be, or what I can try next?

  Read the article

• How can I add a second hard drive to a previously configured UEFI/ACHI Windows 8 machine?

  - by pflyer

  Recently purchased a new Windows 8 PC. It came with one hard drive. I want to a second hard drive to it. This second hard drive is my data hard drive from my previous computer. However, I have run into issues when the system accesses it. The drive is found in the BIOS. But is not seen by Explorer or Disk Management. I have added the drive to the next available SATA slot: SATA 2. The machine is a UEFI/ACHI based machine. In my reading I have found people documenting the following: 1) adding multiple partitioned hard drives (like mine is) to UEFI based machines is not possible 2) I have seen it suggested that you can only add blank hard drives to UEFI based machines. However, in doing so, I did not have success. I tried to add it as a hard drive with unallocated space and then as a hard drive with a single simple partition. Both attempts failed. My ultimate question: What is the proper procedure for adding a second hard drive to a UEFI/ACHI machine? I do not want to reinstall the OS and start from scratch as I have seen suggested elsewhere. There has to be a way to accomplish this without all that hassle. Thanks in advance for your help.

  Read the article

• How can I boot from .iso images stored on the harddrive ?

  - by user29701

  I want to put a .iso file of a bootable linux CD on the harddrive of my computer. I want to have it boot using grub (or lilo), and have it boot from the .iso file as if the .iso was a real CD in the CDROM drive. Here is a page that makes reference to doing this, but instead of a .iso file it is a .img file of a floppy or a whole harddisk installation: http://grub4dos.sourceforge.net/wiki/index.php/Grub4dos%5Ftutorial That page makes reference to "cdrom emulation is not supported", but I don't know if it is not supported in grub, or if what want to do is completely impossible. Apparently Epidemic Linux (and maybe Knoppix ?) have a "bootfrom" parameter: "Using the parameter “bootfrom=/partition/path” you can start Epidemic from an ISO image located anywhere on the HD without having to create a DVD. This is very handy for testing the system." (From www.epidemiclinux.org/ ) Drew P.S. I am NOT interested in installing the CD on the harddrive. If I could have a dozen .iso's on the harddrive, I would like to be able to select them from grub and boot each of them.

  Read the article

• My bios datetime is resetting to 2002, what should I do?

  - by Thierry Lam

  I bought my PC brand new in mid-2006. I'm currently dual booting Win XP 32 bits and Ubuntu Karmic Desktop. Over the last few days, when I boot up my computer, it tells me that my bios time is not set. I now have 2 choices for booting in: Windows first: I can safely get into Windows but the date now shows 2002/01/01 at 00:00. From there, Windows will not sync its time to its servers, I have to manually advance the date myself. I can also advance the date from the bios at startup. Ubuntu first: Since the time date is still set at 2002, the boot system cannot find my linux partition. I can fix that issue by booting to Windows, set the date properly and the linux issue will be fixed automatically. The above two issues can also be fixed if I manually set the bios date/time manually when I turn on my computer. It's annoying to do that every single day since I shut down my PC daily. Am I having an OS issue or a hardware issue? How can I resolve this problem?

  Read the article

• OS X won't boot up unless I hold down option key

  - by Gazzer

  I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• port forwarding/network settings preventing from game hosting

  - by Xitcod13

  I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

  Read the article

• 750Gig Hard Drive shows full with only 315Gigs used

  - by Chris Kelly

  I have a Win7 laptop with a 750Gig C: drive. It came partitioned with 714Gig usable from manufacturer. I installed programs, music files, etc up to 285 gigs. As of a few weeks ago it showed 285 Gigs. Two weeks of house guests later and it shows HD is full. I deleted some files but it still shows 652 Gigs on this drive while there are only 285 Gigs on drive. Relevant details: I am Administrator on laptop and have fair knowledge of what I am doing. I did not restore from backup, restore from mirror, upgrade HD's or anything else that would have touched the partition structure. Just daily use as imaging machine and web. I have checked partitions under disk administrator - no change, still partitioned with 714Gigs usable. Have looked through computer C drive by hand showing Hidden files and folders - no change. I have used JDisk Report to double check - it shows I have only 285 Gigs on C drive. I triple checked with TreeSize run as Administrator and it also shows 285 Gigs on C drive - yet Windows 7 still shows almost full. I used Windows 7 Utilities to Check for Disk Errors, and Defragged the drive. No errors shown and no change after Defrag.

  Read the article

• Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

< Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >