Search Results

Search found 26742 results on 1070 pages for 'linux kernel'.

Page 404/1070 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

  • vlans on openvz, centos 6

    - by arheops
    i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

    Read the article

  • Perform action based on load avg

    - by sfx
    I'm running some web applications on an debian server and have to struggle with ddos attacks sometimes. It's eating up all my resources and I can't ssh anymore into the server. An idea was to drop all connections if the load avg is too high, so there are still resources for me and accept new connections if the load avg is low enough. Since this has to work under heavy load I'm afraid a cronjob wouldn't be fast enough or take too much resources. tl;dr: Is there a way to configure the behavior if the load avg is above a specific threshold?

    Read the article

  • How to find date/time used by Cassandra

    - by JDI Lloyd
    Earlier this morning I noticed that one of the nodes in our Cassandra cluster is writing logs an hour in the future, despite the date/time being correct on the OS. A couple of other nodes I checked via logs appear to be writing logs at the correct time. I now need to go through and check each node in our 80 node cluster and ensure cassandra is running on the correct time, problem being is some of the nodes don't write to the logs very often as they aren't doing much... the question is, is there some form of tool/utility (ie nodetool) that can tell me the time that cassandra is running on? All the systems date/times are correct, ntpdate cron in place has been for a while. Servers are set to Belize timezone to avoid DST changes so its nothing to do with that.

    Read the article

  • Owner of uploads directory is `www-data` but this prevents FTP access via PHP scripts

    - by letseatfood
    To allow write access to Apache, I needed to chown www-data:www-data /var/www/mysite/uploads to my site's upload folder. This allows me to delete files from the folder via unlink() in a PHP script. Unfortunately, this prevents another PHP script, which uses FTP functions, from working. I think it is because the FTP user is mike and now that the uploads directory is owned by www-data, mike cannot access it. I added mike to the group www-data, but this does not fix the issue. Can somebody advise me on how to allow PHP FTP functions to work in addition to file deletion using PHP's unlink() function?

    Read the article

  • Is there a way to obtain the raw image from a Norton Ghost file ?

    - by amo-ej1
    I have a Norton Ghost .gho file, and basicly I want to extract the raw image out of this, for example to use with with tools like dd. (So using any symantec/windows tools is not an option). Is there any open source tool which can deal with these .gho files ? (Note: the.gho file I'm using is a sector based one, and not a file-based one, which implies that things such as Ghost explorer won't work either (see this page)

    Read the article

  • GNU Screen: Combining split-regions and full-screen sessions

    - by scrrr
    Let's say I have three sessions: 0, 1 and 2 I'm on session 0 and I press CTRL-A S to split the screen. Then I select session 1 for the bottom split region, while 0 is in the upper. Can I switch to session 2 and have it display in full-screen while 0 and 1 remain split? If I CTRL-A n to other sessions in a split screen it only changes the split-region. I want some sessions to be full-screen though. Is that possible?

    Read the article

  • testdisk - recover partition table

    - by Evaggelos Balaskas
    I destroyed my partition table of my laptop. Testdisk reports the below Disk laptop.img - 250 GB / 232 GiB - CHS 30402 255 63 (RO) Partition Start End Size in sectors >P MS Data 435868 456606 20739 [NO NAME] P MS Data 19232600 19235479 2880 [NO NAME] D MS Data 41945087 83890143 41945057 D MS Data 57151486 168579069 111427584 D MS Data 67637246 141037565 73400320 D MS Data 151523326 193466365 41943040 D MS Data 170617328 170618223 896 D MS Data 170631168 170634047 2880 D MS Data 171338232 171344405 6174 [Boot] D MS Data 172008235 172231918 223684 [NO NAME] P MS Data 193466368 214437887 20971520 D MS Data 217321375 225321678 8000304 [root] D MS Data 224923646 308809725 83886080 [media] D MS Data 308809728 420237311 111427584 D MS Data 418910206 481824765 62914560 [vmimages] my partition table had 3 Primary Partitions. 1. WinXP Home 2. /boot 3. LVM inside LVM i had 9 or 10 LVM partitions One of them was my home (encrypted with luks) testdisk cant recover my partition table or any other partition. Partitions with [P] doesnt have any useful data. I want to use dd to extract the partitions and try to recover as many files i can. Any ideas of how i can extract eg. the [root] lvm partition from the above testdisk report ? I am afraid that my disk was also corrupted.

    Read the article

  • Why does dstat show zeroes for disk activity on my virtual private server running Ubuntu?

    - by Jonathan Berger
    I'm trying to monitor the number of disk reads and writes on my VPS (Rackspace in this case) running Ubuntu 9.04. I realize there are many tools to do this, but when using dstat 0.7 I tried the following command: dstat -d The output is just two columns of zeroes even when I upload a large file via scp that should be causing a large number of disk writes. Why is this, and how do I get dstat to correctly display the number of disk reads and writes?

    Read the article

  • My control key doesn't work, how do I fix it??

    - by Blaine LaFreniere
    My control key on the right doesn't work how it should. E.g. Right ctrl + T won't open new tabs in firefox, right ctrl + w won't switch windows in vim, etc. I know the key isn't physically broken, because xev shows that the right ctrl key generates events, but it just isn't responding as I expect it to in applications. Screenshot: http://i46.tinypic.com/33w1h76.png I tried Kim's answer but it still doesn't work. blaine@blaine-laptop ~ $ xmodmap -pke | grep 105 keycode 105 = Control_R Control_R Control_R Control_R Control_R Tried to map as Control_L as well, didn't work. The computer is a laptop, I am unable to plug the keyboard in to another computer.

    Read the article

  • One incorrect SSH login attempt locks me out for an hour...

    - by Legend
    I've never observed this problem neither did any of my colleagues trying to SSH into the same system. If I try logging into my server using a wrong username and then press ^C to terminate or exhaust my password attempts, I am locked out for at least an hour. Is there something I can do on my end to fix this problem?

    Read the article

  • samba4 not building in Arch

    - by kmplsv
    cp bin/tdbtool bin/tdbdump bin/tdbbackup /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/bin cp ./include/tdb.h /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/include cp tdb.pc /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/pkgconfig cp libtdb.a libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 mkdir -p /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` cp tdb.so /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` /bin/install -c -d /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8 for I in manpages/*.8; do \ /bin/install -c -m 644 $I /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8; \ done /bin/install: cannot stat `manpages/*.8': No such file or directory make: *** [installdocs] Error 1 Aborting... ==> ERROR: Makepkg was unable to build samba4. ==> Restart building samba4 ? [y/N] ==> ------------------------------- ==>c Any ideas as what is causing my build to fail? I assume it's an issue with manpages I can't figure out exactly what package it is looking for that I don't have.

    Read the article

  • View hidden contents of usb device

    - by Srikanth Suresh
    I have a USB with the following contents on ls -lah total 8.0K drwx------ 1 srikanth srikanth 4.0K May 27 22:54 . drwxr-xr-x 4 root root 4.0K May 28 19:37 .. -rw------- 2 srikanth srikanth 0 May 27 22:52 Files.az3w On viewing the properties of the folder I have the following information: 90.4Mb used and 16.1GB free There is data in this pen drive which I am currently unable to view also it is sensitive. After searching about hiding contents in a USB I think that there is a hidden partition here that I cant access. How should I proceed to view the contents without damaging the files already present?

    Read the article

  • How can I fix this configure error?

    - by balor123
    I'm trying to build mosh from source on a SUSE10 machine and am getting the following error: checking for protobuf... no configure: error: Package requirements (protobuf) were not met: No package 'protobuf' found Consider adjusting the PKG_CONFIG_PATH environment variable if you installed software in a non-standard prefix. Alternatively, you may set the environment variables protobuf_CFLAGS and protobuf_LIBS to avoid the need to call pkg-config. See the pkg-config man page for more details. I downloaded the source to protobuf and installed it in a custom path as well. I'm not using a package manager for any of this and cannot for various reasons outside the scope of the question. I added that custom path to my PATH and rehashed. Typically, this is enough for configure but in this case its not doing the trick. I added the prefix for protobuf to PKG_CONFIG_PATH but am still hitting this error. What should I do next to get past this error?

    Read the article

  • When does /tmp get cleared?

    - by John Lawrence Aspden
    I'm taking to putting various files in /tmp, and I wondered what the rules on deleting them are? I'm imagining it's different for different distributions, and I'm particularly interested in Ubuntu and Fedora desktop versions. But a nice general way of finding out would be a great thing. Even better would be a nice general way of controlling it! (Something like 'every day at 3 in the morning, delete any /tmp files older than 60 days, but don't clear the directory on reboot')

    Read the article

  • Xinerama creates a panning viewport

    - by iblue
    EDIT: I've created a bug report: https://bugs.freedesktop.org/show_bug.cgi?id=48458 My Setup I have 4 monitors, 1920x1080, which are in portrait mode (rotated left). They are connected to two radeon graphic cards. As usual, a picture says more than a thousand words. The problem Everything works fine, when Xinerama is disabled. But when I enable Xinerama, things get weird. When I move the mouse of the screen and return, the screen contents begin to move with the mouse, only on this monitor. It seems like the virtual display size does not match the real screen size, which activates a panning viewport. Any idea how to stop this? The video I created a video to demonstrate the issue: http://www.youtube.com/watch?v=zq_XHji1P24 xorg.conf This is my xorg.conf: Section "ServerLayout" ##################[ Evilness begins here ]############# Option "Xinerama" "on" # <--- Makes it go b0rked! ##################[ End of all evil ]############# Identifier "BOFH Console of Doom" Screen 0 "Screen-0" 0 0 Screen 1 "Screen-1" RightOf "Screen-0" Screen 2 "Screen-2" RightOf "Screen-1" Screen 3 "Screen-3" RightOf "Screen-2" EndSection Section "ServerFlags" Option "RandR" "false" EndSection Section "Module" Load "dbe" Load "dri" Load "extmod" Load "dri2" Load "record" Load "glx" EndSection Section "Monitor" Identifier "Monitor-0" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-1" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-2" Option "Rotate" "left" EndSection Section "Monitor" Identifier "Monitor-3" Option "Rotate" "left" EndSection Section "Device" Identifier "Radeon-0-0" Driver "radeon" BusID "PCI:9:0:0" Option "ZaphodHeads" "DVI-0" Screen 0 EndSection Section "Device" Identifier "Radeon-0-1" Driver "radeon" BusID "PCI:9:0:0" Option "ZaphodHeads" "DVI-1" Screen 1 EndSection Section "Device" Identifier "Radeon-1-0" Driver "radeon" BusID "PCI:4:0:0" Option "ZaphodHeads" "DVI-2" Screen 0 EndSection Section "Device" Identifier "Radeon-1-1" Driver "radeon" BusID "PCI:4:0:0" Option "ZaphodHeads" "DVI-3" Screen 1 EndSection Section "Screen" Identifier "Screen-0" Device "Radeon-0-0" Monitor "Monitor-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-1" Device "Radeon-0-1" Monitor "Monitor-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-2" Device "Radeon-1-0" Monitor "Monitor-2" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen-3" Device "Radeon-1-1" Monitor "Monitor-3" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

    Read the article

  • How can I limit the upload/download bandwidth on my CentOS server?

    - by Dan Nestor
    How can I limit the upload and download bandwidth on my CentOS server? This is a box with a single interface, eth0. Ideally, I would like a command-line solution (I've been trying to use tc), something that I could easily switch on and off in a script. So far I've been trying to do something like tc filter add dev eth0 protocol ip prio 50 u32 police rate 100kbit burst 10240 drop but I'm obviously missing a lot of knowledge and information. Can somebody help with a quick one-liner? Many thanks, Dan

    Read the article

  • Can't ping through default gateway

    - by Andrew G.H.
    I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

    Read the article

  • Is segfault signal always sent to application

    - by noonex
    My application usually crashes and prints stack to log if received segfault signal. But in some environment the 'dmesg' shows segfault messages related to my application, but application uptime is much older. Can segfault be suppressed and application doesn't receive signal? Or what errors from dmesg can mean ?

    Read the article

  • Unix domain socket firewall

    - by lagab
    Hello, everyone. I've got a problem with my debian server. Probably there is some vulnerable script at my web-serser, which is running from www-data user. I also have samba with winbind installed, and samba is joined to windows domain. So, probably this vulnerable script allows hacker to bruteforce out domain controller through winbind unix domain socket. Actually I have lots of such lines at netstat -a output: unix 3 [ ] STREAM CONNECTED 509027 /var/run/samba/winbindd_privileged/pipe And our DC logs contain lots of recorded authentication attems from root or guest accounts. How can I restrict my apaches access to winbind? I had an idea to use some kind of firewall for IPC sockets. Is it possible?

    Read the article

  • dhcpd pool exhaustion - What's the result?

    - by jarmund
    I have a DHCP server that serves leases to several houndred, maybe up to a thousand, different clients on an average day. The pool consists of 242 IPs, and due to the highly dynamic nature of the network, it's enough 99% of the time (most devices are gone from the network in a few minutes), despite having a lease time of 3600. Now, imagine if more clients than that connect to the network during an hour. The sollution is obvious: Decrease lease time, or increase the DHCP pool, however, what i would like to know: What happens when dhcpd has exhausted the pool? Are new DHCP requests simply ignored?

    Read the article

  • SSH multi-hop connections with netcat mode proxy

    - by aef
    Since OpenSSH 5.4 there is a new feature called natcat mode, which allows you to bind STDIN and STDOUT of local SSH client to a TCP port accessible through the remote SSH server. This mode is enabled by simply calling ssh -W [HOST]:[PORT] Theoretically this should be ideal for use in the ProxyCommand setting in per-host SSH configurations, which was previously often used with the nc (netcat) command. ProxyCommand allows you to configure a machine as proxy between you local machine and the target SSH server, for example if the target SSH server is hidden behind a firewall. The problem now is, that instead of working, it throws a cryptic error message in my face: Bad packet length 1397966893. Disconnecting: Packet corrupt Here is an excerpt from my ~/.ssh/config: Host * Protocol 2 ControlMaster auto ControlPath ~/.ssh/cm_socket/%r@%h:%p ControlPersist 4h Host proxy-host proxy-host.my-domain.tld HostName proxy-host.my-domain.tld ForwardAgent yes Host target-server target-server.my-domain.tld HostName target-server.my-domain.tld ProxyCommand ssh -W %h:%p proxy-host ForwardAgent yes As you can see here, I'm using the ControlMaster feature so I don't have to open more than one SSH connection per-host. The client machine I tested this with is an Ubuntu 11.10 (x86_64) and both proxy-host and target-server are Debian Wheezy Beta 3 (x86_64) machines. The error happens when I call ssh target-server. When I call it with the -v flag, here is what I get additionally: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /home/aef/.ssh/config debug1: Applying options for * debug1: Applying options for target-server.my-domain.tld debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: auto-mux: Trying existing master debug1: Control socket "/home/aef/.ssh/cm_socket/[email protected]:22" does not exist debug1: Executing proxy command: exec ssh -W target-server.my-domain.tld:22 proxy-host.my-domain.tld debug1: identity file /home/aef/.ssh/id_rsa type -1 debug1: identity file /home/aef/.ssh/id_rsa-cert type -1 debug1: identity file /home/aef/.ssh/id_dsa type -1 debug1: identity file /home/aef/.ssh/id_dsa-cert type -1 debug1: identity file /home/aef/.ssh/id_ecdsa type -1 debug1: identity file /home/aef/.ssh/id_ecdsa-cert type -1 debug1: permanently_drop_suid: 1000 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.0p1 Debian-3 debug1: match: OpenSSH_6.0p1 Debian-3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1 Debian-7ubuntu1 debug1: SSH2_MSG_KEXINIT sent Bad packet length 1397966893. Disconnecting: Packet corrupt

    Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >