Search Results

Search found 26742 results on 1070 pages for 'linux kernel'.

Page 407/1070 | < Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >

  • Slight delay when switching modes in vim using tmux or screen

    - by Ton van den Heuvel
    Switching to and from insert mode in Vim is no longer instantaneous since I use tmux. After pressing Esc in insert mode, it takes a noticeable amount of time to actually get out of insert mode. After pressing Esc and any other key afterwards the switch is immediate, and the command for the key pressed after Esc is executed. Any idea what might cause this? The Vim configuration is not the problem as the delay does not occur when I run Vim outside tmux, so this is probably related to tmux somehow. I use gnome-terminal btw. Also worth noting, it seems I can not define key bindings in tmux for Esc, my plan was to bind Esc to: bind Escape send-keys ^[ Alas, it seems binding anything to Esc for tmux does not work. The same problem occurs in screen as well.

    Read the article

  • IPtables: DNAT not working

    - by GetFree
    In a CentOS server I have, I want to forward port 8080 to a third-party webserver. So I added this rule: iptables -t nat -A PREROUTING -p tcp --dport 8080 -j DNAT --to-destination thirdparty_server_ip:80 But it doesn't seem to work. In an effort to debug the process, I added these two LOG rules: iptables -t mangle -A PREROUTING -p tcp --src my_laptop_ip --dport ! 22 -j LOG --log-level warning --log-prefix "[_REQUEST_COMING_FROM_CLIENT_] " iptables -t nat -A POSTROUTING -p tcp --dst thirdparty_server_ip -j LOG --log-level warning --log-prefix "[_REQUEST_BEING_FORWARDED_] " (the --dport ! 22 part is there just to filter out the SSH traffic so that my log file doesn't get flooded) According to this page the mangle/PREROUTING chain is the first one to process incomming packets and the nat/POSTROUTING chain is the last one to process outgoing packets. And since the nat/PREROUTING chain comes in the middle of the other two, the three rules should do this: the rule in mangle/PREROUTING logs the incomming packets the rule in nat/PREROUTING modifies the packets (it changes the dest IP and port) the rule in nat/POSTROUTING logs the modified packets about to be forwarded Although the first rule does log incomming packets comming from my laptop, the third rule doesn't log the packets which are supposed to be modified by the second rule. It does log, however, packets that are produced in the server, hence I know the two LOG rules are working properly. Why are the packets not being forwarded, or at least why are they not being logged by the third rule? PS: there are no more rules than those three. All other chains in all tables are empty and with policy ACCEPT.

    Read the article

  • Debian wheezy keyboard shortcut for both opening and closing a terminal

    - by Peter
    I recently installed tilda and I would like to open it and close with the same keyboard shortcut. I wrote little something in bash that closes tilda if it is open and opens tilda when there is no such a process in ps -ef. It looks like this: a=ps -ef | fgrep -i tilda | cut -d' ' -f4 | head -1;if [ $a ] ; then kill $a; else tilda; fi It seems to be working (at least partially) when I commit this in terminal, but when I assign this command to specific keyboard shortcut (for example alt+1) it does nothing. Any suggestions? btw. is it possible to assign this shortcut for button '`' like in Quake?

    Read the article

  • What parameters to mdadm, to re-create md device with payload starting at 0x22000 position on backing storage?

    - by Adam Ryczkowski
    I try to recover from mdadm raid disaster, which happened when moving from ubuntu server 10.04 to 12.04. I know the correct order of devices from dmesg log, but given this information, I still cannot access the data. The superblocks look messy; the mdadm --examine for each disk is on this question on askubuntu By inspecting the raw contents of backing storage, I found the beginning of my data (the LUKS container in my case) at position 0x22000 relative to the beginning of the first partition in the raid. Question: What is the combination of options issued to "mdadm --create" to re-create mdadm that starts with the given offset? Bitmap size? PS. The relevant information from syslog when the system was healthy are pasted here.

    Read the article

  • Hybrid gmail MX + postfix for local accounts

    - by krunk
    Here's the setup: We have a domain, mydomain.com. Everything is on our own server, except general email accounts which are through gmail. Currently gmail is set as the MX record. The server also has various email aliases it needs to support for bug trackers and such. e.g. [email protected] |/path/to/issuetracker.script I'm struggling with a setup that allows the following, both locally and from user's email clients. guser1 - has a gmail account and a local account guser2 - only has a gmail account bugs - has a pipe alias in /etc/aliases for issue tracker Scenarios mail to [email protected] from local host (crons and such) needs to go to gmail account mail to [email protected] from local host mail to [email protected] needs to be piped to the local issue tracker script So, the first stab was creating a transport map. In this scenario, the our server would be set as teh MX and guser* destined emails are sent to gmail. Put the gmail users in a map like so: [email protected] smtp:gmailsmtp:25 [email protected] smtp:gmailsmtp:25 Problems: Ignores extensions such as [email protected] Only works if append_at_myorigin = no (if set to yes, gmail refuses to connect with: E4C7E3E09BA3: to=, relay=none, delay=0.05, delays=0.02/0.01/0.02/0, dsn=4.4.1, status=deferred (connect to gmail-smtp-in.l.google.com[209.85.222.57]:25: Connection refused)) since append_at_myorigin is set to no, all received emails have (unknown sender) The second stab was to set explicit localhost aliases in /etc/aliases and do a domain wide forward on mydomain. This too requires setting the local server as the MX: root: root@localhost # transport mydomain.com smtp:gmailsmtp:25 Problems: * If I create a transport map for a domain that matches "$myhostname", the aliases file is never parsed. So when a local user (or daemon) sends an email like: mail -s "testing" root < text.txt Postfix ignores the /etc/alias entry and maps to [email protected] and attempts to send it to the gmail transport mapping. Third stab: Create a subdomain for the bugs, something like bugs.mydomain.com. Set the MX for this domain to local server and leave the MX for mydomain.com to the Gmail server. Problems: * Does not solve the issue with local accounts. So when the bug tracker responds to an email from [email protected], it uses a local transport and the user never receives the email. % postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_at_myorigin = no append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = $myhostname, localhost.$myhostname, localhost myhostname = mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_cert_file = /etc/ssl/certs/kspace.pem smtp_tls_enforce_peername = no smtp_tls_key_file = /etc/ssl/certs/kspace.pem smtp_tls_note_starttls_offer = yes smtp_tls_scert_verifydepth = 5 smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination smtpd_tls_ask_ccert = yes smtpd_tls_req_ccert = no smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

    Read the article

  • Only One GPU Detected in the Nvidia Quadra NVS 450

    - by Kyle Brandt
    I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia... Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there): # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010 Section "ServerLayout" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+275, DFP-3: nvidia-auto-select +1680+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-3" Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-3: nvidia-auto-select +1680+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "DFP-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection lscpi: 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer Registers Port 0 (rev 13) 00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol Layer Registers Port 0 (rev 13) 00:11.0 PIC: Intel Corporation 5520/5500 Physical and Link Layer Registers Port 1 (rev 13) 00:11.1 PIC: Intel Corporation 5520/5500 Routing & Protocol Layer Register Port 1 (rev 13) 00:13.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub I/OxAPIC Interrupt Controller (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:15.0 PIC: Intel Corporation 5520/5500/X58 Trusted Execution Technology Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 IDE interface: Device 1b4b:91a3 (rev 11) 02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) 03:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:02.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 05:00.0 3D controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 06:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 08:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 08:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0b:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

    Read the article

  • Out Of Memory Error - Magento

    - by robobobobo
    Ok normally I understand when my server is giving me out of memory errors, but this one has me stumped! I'm running a magento based site, with one or two plugins in it and the rest is pretty basic. The site runs and loads fine wiht no issues. However in the backend - Configuration - Payment Methods it gives me the following out of memory error Fatal error: Out of memory (allocated 39059456) (tried to allocate 85 bytes) in ########/Varien/Simplexml/Element.php on line 84 Now this is where I'm confused..it's allocated more than it tried to allocate? Am I correct there? So how is it running out of memory? My server has 6Gb ram, an SSD and 2 CPU's running WHM with a few other low traffic sites on it. I set my php memory limit to 100mb, 1000mb and finally unlimited but all to no avail! I'm completely lost here, would really appreciate some expertise on this Cheers

    Read the article

  • My control key doesn't work, how do I fix it??

    - by Blaine LaFreniere
    My control key on the right doesn't work how it should. E.g. Right ctrl + T won't open new tabs in firefox, right ctrl + w won't switch windows in vim, etc. I know the key isn't physically broken, because xev shows that the right ctrl key generates events, but it just isn't responding as I expect it to in applications. Screenshot: http://i46.tinypic.com/33w1h76.png I tried Kim's answer but it still doesn't work. blaine@blaine-laptop ~ $ xmodmap -pke | grep 105 keycode 105 = Control_R Control_R Control_R Control_R Control_R Tried to map as Control_L as well, didn't work. The computer is a laptop, I am unable to plug the keyboard in to another computer.

    Read the article

  • VirtualBox - multiple guests, each with a single bridged adapter?

    - by Martin
    I am running a dedicated server (located at Hetzner, Germany) that runs VirtualBox in order to virtualize several services accross multiple virtual guests. Those guests are supposed to communicate with each other (for instance, a virtual web server has to access a virtual database server); to be reachable from the dedicated server (for instance, SSH access); and to access the Internet via the dedicated server (for instance, to download security updates) Currently, this is achieved by having host-only adapter vboxnet0 on the dedicated server and two virtual interfaces on each guest. There, virtual adapter eth0 is attached to vboxnet0 (to achieve (1) and (2)), virtual adapter eth1 is attached to VirtualBox' NAT (to achieve (3)). Via eth0, the guests have access to a DHCP and a DNS server, both running on the dedicated server (there, bound to vboxnet0). This allows me to assign custom IP addresses and names. Via eth1, VirtualBox pushes a proper route that enables each guest to access the Internet (via eth0 on the dedicated server). This setup with two virtual adapters frequently leads to problems and at leasts complicates many things. For instance, on the dedicated server there is OpenVPN which allows to access the virtual machines via the Internet; futhermore, there is Shorwall that controls the incoming and outgoing network traffic between the Internet, the dedicated server, and the individual virtual machines. Not to mention automatic installation of servers via PXE... Therefore, I would prefer to have only one single virtual adapter on each guest which would be used for both incoming and outgoing connections. As far as I understand, one would basically use a bridged interface for that very purpose. Now the question arises: Which interface on the dedicated server would the bridge use? eth0 on the host server is not an option, as this is prohibited by the provider. A virtual interface eth0:0 would not make any sense, as a bridge always uses a physical interface (eth0 in this case). Would it be possible to create a bridged interface in each virtual machine that would "dangle in the air"? Thus, without a complement on the dedicated server? How would I have to set up the routing on the host server? Please note that the host / dedicated server has only one network adapter (eth0) which is connected to the provider's network. Regards, Martin

    Read the article

  • Issue with multiple bridging for KVM hosts

    - by Henry-Nicolas Tourneur
    I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

    Read the article

  • System information shown when booting Debian

    - by WebDevHobo
    When booting Debian, you'll see it printing a lot of information about the system variables and such. I don't really need to see all that, so I'd like to modify some scripts to make sure that on boot, it just does what it has to do, without printing it on the screen. Just something I fancy. Offcourse, still seeing errors would be nice. But that long slur of text, I could do without. I've tried looking it up, but I can't find documentation on this specific thing anywhere.

    Read the article

  • Ubuntu 10.04 freezing and Ctrl + Alt + Backspace does nothing but music keeps playing

    - by Bryce Thomas
    I'm having intermittent problems where the screen will freeze in Ubuntu. I've tried using Ctrl + Alt + Backspace to restart the X-server, though this does nothing. When the freeze occurs, there's a small square of black dashes around the mouse pointer - maybe 1 inch in size. These dashes look a lot like a 2d barcode. The rest of the screen looks normal, but I can't move the mouse and none of the keyboard shortcuts work to do anything. However, music that I begin playing before the freeze continues to play, which seems to indicate it hasn't stalled up completely. I've noticed a similar freezing problem when I'm using Windows 7. That is, I see the same barcode like dashes around the mouse pointer when it freezes up. So I'm guessing it's either a driver or hardware problem. I thought if it was a hardware problem though, the whole computer might stop working (i.e. music would stop playing)? The video card I am using is an Nvidia, and I believe it's in the 7600 range. In Ubuntu I have the drivers for the card set to the latest available (proprietary). Ideally I'd like to be able to continue using the proprietary drivers. Is there any known issues with the drivers for this model graphics card, or has anyone experienced the same problem and knows how to fix it?

    Read the article

  • Script execution flow stopped?

    - by vijay.shad
    Hi all, Now my script is able to start server, But I am still have some problem with my script. When the start server command is executed, the control does not pass the line and does not execute further of that line. Please tell me what is the problem and how can I get smooth execution of the my script.

    Read the article

  • Simple mdadm RAID 1 not activating spare

    - by Nick Liu
    I had created two 2TB HDD partitions (/dev/sdb1 and /dev/sdc1) in a RAID 1 array called /dev/md0 using mdadm on Ubuntu 12.04 LTS Precise Pangolin. The command sudo mdadm --detail /dev/md0 used to indicate both drives as active sync. Then, for testing, I failed /dev/sdb1, removed it, then added it again with the command sudo mdadm /dev/md0 --add /dev/sdb1 watch cat /proc/mdstat showed a progress bar of the array rebuilding, but I wouldn't spend hours watching it, so I assumed that the software knew what it was doing. After the progress bar was no longer showing, cat /proc/mdstat displays: md0 : active raid1 sdb1[2](S) sdc1[1] 1953511288 blocks super 1.2 [2/1] [U_] And sudo mdadm --detail /dev/md0 shows: /dev/md0: Version : 1.2 Creation Time : Sun May 27 11:26:05 2012 Raid Level : raid1 Array Size : 1953511288 (1863.01 GiB 2000.40 GB) Used Dev Size : 1953511288 (1863.01 GiB 2000.40 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Mon May 28 11:16:49 2012 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : Deltique:0 (local to host Deltique) UUID : 49733c26:dd5f67b5:13741fb7:c568bd04 Events : 32365 Number Major Minor RaidDevice State 1 8 33 0 active sync /dev/sdc1 1 0 0 1 removed 2 8 17 - spare /dev/sdb1 I've been told that mdadm automatically replaces removed drives with spares, but /dev/sdb1 isn't being moved into the expected position, RaidDevice 1. UPDATE (30 May 2012): A badblocks destructive read-write test of the entire /dev/sdb yielded no errors as expected; both HDDs are new. As of the latest edit, I assembled the array with this command: sudo mdadm --assemble --force --no-degraded /dev/md0 /dev/sdb1 /dev/sdc1 The output was: mdadm: /dev/md0 has been started with 1 drive (out of 2) and 1 rebuilding. Rebuilding looks like it's progressing normally: md0 : active raid1 sdc1[1] sdb1[2] 1953511288 blocks super 1.2 [2/1] [U_] [>....................] recovery = 0.6% (13261504/1953511288) finish=2299.7min speed=14060K/sec unused devices: <none> I'm now waiting on this rebuild, but I'm expecting /dev/sdb1 to become a spare just like the five or six times that I've tried rebuilding before. UPDATE (31 May 2012): Yeah, it's still a spare. Ugh! UPDATE (01 June 2012): I'm trying Adrian Kelly's suggested command: sudo mdadm --assemble --update=resync /dev/md0 /dev/sdb1 /dev/sdc1 Waiting on the rebuild now... My questions are: Why isn't the spare drive becoming active sync? How can I make the spare drive become active?

    Read the article

  • Sendmail doesn't work with iptables, even though smtp and dns are allowed

    - by tom
    I have sendmail installed on Ubuntu 10.04 solely for the use of the php mail() function. This works fine unless iptables is running (I've been using sendmail [email protected] to test this). I think that I have allowed SMTP and DNS (the script I am using to test iptables rules is below, in my version are the actual IPs of my hosts nameservers), but to no avail! iptables --flush iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Postgres iptables -A INPUT -p tcp --dport 5432 -j ACCEPT # Webmin iptables -A INPUT -p tcp --dport 10000 -j ACCEPT # Ping iptables -A INPUT -p icmp --icmp-type echo-request -j ACCEPT iptables -A OUTPUT -p icmp --icmp-type echo-reply -j ACCEPT # sendmail iptables -A INPUT -p tcp --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 25 -m state --state ESTABLISHED -j ACCEPT # DNS iptables -A INPUT -p udp --sport 53 -s <nameserver1> -j ACCEPT iptables -A INPUT -p udp --sport 53 -s <nameserver2> -j ACCEPT iptables -A INPUT -p tcp --sport 53 -s <nameserver1> -j ACCEPT iptables -A INPUT -p tcp --sport 53 -s <nameserver2> -j ACCEPT iptables -A OUTPUT -p udp --dport 53 -d <nameserver1> -j ACCEPT iptables -A OUTPUT -p udp --dport 53 -d <nameserver2> -j ACCEPT iptables -A OUTPUT -p tcp --dport 53 -d <nameserver1> -j ACCEPT iptables -A OUTPUT -p tcp --dport 53 -d <nameserver2> -j ACCEPT iptables -A INPUT -j DROP # Add loopback iptables -I INPUT 1 -i lo -j ACCEPT

    Read the article

  • How to close all background processes in unix?

    - by Gabi Purcaru
    I have something like: cd project && python manage.py runserver & cd utilities && ./coffee_auto_compiler.py And I want both of them to close on Ctrl-C (or some other command). How can I accomplish that? EDIT: I tried using jobs -x kill and kill `jobs -p `, but it doesn't seem to kill what I need. Here is what I mean: moon 8119 0.0 0.0 7556 3008 pts/0 S 13:17 0:00 /bin/bash moon 8120 6.8 0.4 24568 18928 pts/0 S 13:17 0:00 python manage.py runserver jobs -p give me just process 8119, but I also need to close 8120, since it's the thing that the first command opened. If it helps, the commands are actually in a Makefile, and I want it to run two daemons at the same time (and somehow close them at the same time). And yes, I'm using ubuntu, with bash

    Read the article

  • Monit network availability checking

    - by viraptor
    Hi, I'd like to start a service with monit but only when I have the correct ip bound to the host. Can this be done somehow with the normal config? For example I want to start a process xxx with pidfile xxx.pid, but only if host currently has 10.0.0.1 bound to some interface.

    Read the article

  • Disabling networkmanager for a specific interface

    - by bdonlan
    I'd like to do some experimentation with hostap without disabling my primary wireless interface. How do I tell networkmanager to keep its hands off a specific interface or interfaces while allowing it to continue managing all other interfaces normally? I'm using Ubuntu 9.04. (Wasn't sure if this should go on superuser or serverfault, as networkmanager isn't much of a 'server' tool - if it belongs on serverfault please feel free to move it) Edit: I've tried adding this to /etc/network/interfaces: allow-hotplug wlan2 iface wlan2 inet static address 192.168.49.1 netmask 255.255.255.0 But this has no apparent effect, even after restarting NetworkManager. Here's my /etc/NetworkManager/nm-system-settings.conf: [main] plugins=ifupdown,keyfile [ifupdown] managed=false Edit[2]: Looks like I needed to restart nm-system-settings, then NetworkManager.

    Read the article

  • DNS issue on Fedora 12? wget wordpress.org fails where wget www.google.com works

    - by Tom Auger
    I'm administering a Fedora 12 box, but am quite new to networking specifics. Recently one of our WordPress apps hosted on our server has stopped being able to perform its auto-update or auto-download of plugins. Investigating further, I have tried the following: $ wget wordpress.org --2010-12-17 11:26:50-- http://wordpress.org/ Resolving wordpress.org... failed: Temporary failure in name resolution. wget: unable to resolve host address âwordpress.orgâ Whereas: $ wget www.google.com --2010-12-17 11:27:26-- http://www.google.com/ Resolving www.google.com... 74.125.226.82, 74.125.226.84, 74.125.226.80, ... Connecting to www.google.com|74.125.226.82|:80... connected. HTTP request sent, awaiting response... 302 Found Location: http://www.google.ca/ [following] --2010-12-17 11:27:26-- http://www.google.ca/ Resolving www.google.ca... 173.194.32.104 Connecting to www.google.ca|173.194.32.104|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: âindex.html.4â [ <=> ] 9,079 --.-K/s in 0.02s 2010-12-17 11:27:26 (462 KB/s) - âindex.html.4â Interestingly: $ ping wordpress.org PING wordpress.org (72.233.56.138) 56(84) bytes of data. 64 bytes from wordpress.org (72.233.56.138): icmp_seq=1 ttl=50 time=81.5 ms 64 bytes from wordpress.org (72.233.56.138): icmp_seq=2 ttl=50 time=67.3 ms ^C --- wordpress.org ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1783ms rtt min/avg/max/mdev = 67.361/74.448/81.536/7.092 ms and $ nslookup wordpress.org Server: 192.168.2.1 Address: 192.168.2.1#53 Non-authoritative answer: Name: wordpress.org Address: 72.233.56.138 Name: wordpress.org Address: 72.233.56.139 nscd has been stopped and flushed. iptables appear to be clean. At this point I have exhausted my limited abilities to diagnose the issue. Can anyone suggest a resolution path?

    Read the article

  • How to install missing Sound Drivers in Ubuntu?

    - by Sakamoto Kazuma
    I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

    Read the article

  • Making libmagic/file detect .docx files

    - by Jonatan Littke
    As seen elsewhere, docx, xlsx and pttx are ZIPs. When uploading them to my web application, file (via libmagic andpython-magic) detects them as being ZIP. I store the contents of the file as a blob in the database, but naturally I don't want to trust the user with what kind of file type this is. So I would like to trust file for and automatically generate a filename during download. I know one can modify /etc/magic but the format (magic(5)) is way too complicated for me. I found a bug report on the issue at Debian bugs but since it's from 2008 it doesn't seem to be fixed any time soon. I guess my only other alternative is to indeed trust the user (but still store the contents as a blob) and only check the file extension based on the file name. This way I can disallow some extensions and allow others. And when the user re-downloads his file, he can have it in whatever way he uploaded it. But this solution is insecure if the file is shared with others, since you can simply rename the file to allow uploading it. Any ideas? Lastly, I found a list of magic numbers for docx etc, but I'm unable to convert these into the magic(5) format.

    Read the article

  • DNS propagation delay or bad configuration?

    - by Javier Martinez
    I have been waiting the DNS propagation for almost 24 hours. I'am no impatient, but I want to know if I configured my zone good or I have any error in it. I think that is good, because if I use my server dns like my DNS secondary I can resolve and lookup host well. ; ; BIND data file for mydomain.net ; $TTL 86400 @ IN SOA mydomain.net. mydomain.net. ( 20120629 ; Serial 10800 ; Refresh 3 hours 3600 ; Retry 1 hour 604800 ; Expire 1 week 86400 ) ; Negative Cache TTL ; @ IN NS ns1 @ IN NS ns2 IN MX 10 mail ns1 IN A 5.39.X.Y ns2 IN A 5.39.X.Z There is not any errors in /var/syslog about bind daemon. Is everything correct? Do I only need to wait up to 48 hours for the right DNS propagation? My nslookup from a remote machine with the nameserver of the bind host: $ nslookup mydomain.net Server: bind-host-ip Address: bind-host-ip#53 Name: mydomain.net Address: domain-ip

    Read the article

  • sSMTP Configuration Question

    - by SevenCentral
    I've installed sSMTP on Ubuntu 10.04 via: sudo apt-get install ssmtp My configuration file is: # # Config file for sSMTP sendmail # # The person who gets all mail for userids < 1000 # Make this empty to disable rewriting. [email protected] # The place where the mail goes. The actual machine name is required no # MX records are consulted. Commonly mailhosts are named mail.domain.com mailhub=smtp.gmail.com:587 # Where will the mail seem to come from? #rewriteDomain= # The full hostname hostname=somedomain.com # Are users allowed to set their own From: address? # YES - Allow the user to specify their own From: address # NO - Use the system generated From: address #FromLineOverride=YES [email protected] authpass=**** usestarttls=yes Am I transmitting my credentials in clear text? Is calling ssmtp a secure operation? Thanks.

    Read the article

  • How to display a graph only for business hours with CACTI?

    - by Blast Raider
    I have noticed that I can only display an uninterrupted period with Cacti. I am wondering whether is possible or not to make a custom graph which displaying only the business hours during a period (a week, a month, etc.). If it is possible, how could I configure it on Cacti ? For example, I would like to be able to display a graph with an average inbound/outbound traffic between 8am and 7pm for 5 business days a week of the last month. I would apreciate any help. Thank you.

    Read the article

< Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >