Search Results

Search found 37931 results on 1518 pages for 'computer case'.

Page 405/1518 | < Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >

  • Hard drives (SATA/ATA) corrupting

    - by JC Denton
    Hello All, 2 years ago I bought relatives a new computer for christmas and installed Ubuntu on it. Ever since then it has been experiencing problems with the hard drives. The hard drive supplied with the machine was a SATA drive. When it appeared it was having problems (files and folders with invalid encoding started appearing) I replaced the SATA drive with the drive of their previous computer. I replaced it (The replacement) later on, the drive being rather old and thus becoming more prone to the risk of failure. The replacement drive is a IDE drive but the same problems started to appear (files and folders showing up in nautilus with invalid encoding). I fear the files and folders that are showing are existing FS entries, starting to corrupt. As it's happening to both the IDE and SATA drive it's unlikely to be the drives themselves or the IDE/SATA controller, I believe. Any ideas as to what could be causing the (assumed) corruption? EDIT: You're right about the paragraphs. They were there in edit mode but I'm still getting to grips with the whitespace format codes. The system is a "Primo Pro" AMD Phenom II X4 Quad Core 920 2.80GHz SILENT DDR2, ordered from overclockers.co.uk and nothing has been added to it except for the replacement of the SATA drive with an AMD drive. It would seem unlikely for a barebones system to be underpowered.

    Read the article

  • Remote Desktop Network Level Authentication Not Supported

    - by Iszi
    I'm running Windows XP Professional SP3 x86, trying to connect to a system with Windows 7 Ultimate SP1 x64. Recently, I updated the Remote Desktop Connection software on the XP system in hopes of using Network Level Authentication (NLA) for my connections to the Windows 7 box. After the update, I connected to the Windows 7 box over RDP and enabled NLA believing that the updated client should support it. After disconnecting and attempting to reconnect, I'm presented with the following error: The remote computer requires Network Level Authentication, which your computer does not support. For assistance, contact your system administrator or technical support. So, I checked the About page in Remote Desktop Connection to make sure the update had applied. This is what I see. Remote Desktop Connection Shell Version 6.1.7600 Control Version 6.1.7600 © 2007 Microsoft Corporation. All rights reserved. Network Level Authentication not supported. Remote Desktop Protocol 7.0 supported. I thought NLA was supposed to be a part of RDP 7.0 clients. Is there a component I'm missing somewhere?

    Read the article

  • My desktop has started overheating -- how hot is hot?

    - by Jerry
    I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

    Read the article

  • How to force a login for an administrator when using Remote Desktop Connection and fast user switching enabled?

    - by brett rogers
    Scenario: I am at work. I want to remote desktop into my machine at home. Problem is, my 5-year-old daughter is playing games on Starfall.com (or something similar) on her (non-admin) account. When I attempt to connect I see this message: Another user is currently logged on to this computer. If you continue, this user has to disconnect from this computer. Do you want to continue? I click Yes and then see Please wait for 'UserName' to respond This presents my daughter with an Allow/Disallow dialog on whether to let me connect. She clicks Disallow (or No or whatever it says) and then I see 'UserName' has denied your request Question: How can I force my account to log in and disconnect her session? Additional Info: My account is an administrator account. My daughter's account is a non-administrator account. Home machine is Windows 7 Pro with fast user switching enabled. Turning off fast user switching is not an option (Kyle pointed out in his answer that turning it off would allow the admin to force another user off). I would keep fast user switching's ability to change accounts without closing the previous account's session over being able to force myself to connect.

    Read the article

  • Best way to 'harden' embedded ext4 file server against unexpected loss of power?

    - by Jeremy Friesner
    Hi all, First, a little background: my company makes an audio streaming device that is a headless, rack-mounted Linux box with a couple of SSDs attached. Each SSD is formatted with ext4. The users can connect to the system using Samba/CIFS to upload new audio files or access existing ones. There is also custom software for streaming out audio over the network. This is all fine. The only problem is that the users are audio people, not computer people, and see the system as a 'black box', not as a computer. Which means that at the end of the day, they aren't going to ssh in to the box and enter "/sbin/shutdown -h"; they are just going to cut power to the rack and leave, and expect things to still work properly the next day. Since ext4 has journalling, journal checksumming, etc, this mostly works. The only time it doesn't work is when someone uploads a new file via Samba and then cuts power to the system before the uploaded data has been fully flushed to the disk. In that case, they come in the next day and find that their new file has been truncated or is missing entirely, and are unhappy. My question is, what is the best way to avoid this problem? Is there a way to get smbd to call "sync" at the end of every upload? (Performance on uploads isn't so important, since they only happen occasionally). Or is there a way to tell ext4 to automatically flush within a few seconds of any change to a file? (Again, performance can be sacrificed for safety here) Should I set a particular write-ordering mode, activate barriers, etc?

    Read the article

  • How to start using twill?

    - by brilliant
    How do I start using twill? I have just downloaded it, unpacked it and clicked on the setup .py file in the folder. The black window (terminal) appeared for a moment and vanished. (I do have Python 2.5 installed on my computer - along with SDK from Google App Engine) In the twill documentation section it says: Downloading twill The latest release of twill is twill 0.9, released Thursday, December 27th, 2007; it is available for download at http://darcs.idyll.org/~t/projects/twill-0.9.tar.gz. You can also use Python's easy_install to install or upgrade twill. twill works with Python 2.3 or later. To start using twill, install it and then type twill-sh. At the prompt type: go http://www.slashdot.org/ show showforms showhistory I am not clear from this passage what I am supposed to type (only "twill-sh" or "twill-sh" and all the words under that line) and where (I tried typing it in the command prompt window of my computer - to no avail) Can, anyone, please, help me out here? Thank You in advance.

    Read the article

  • Where do I define a group policy that will set a users desktop background color to green the first time they log in?

    - by Tyler
    Servers: W2k8 R2 x64 Desktops: Win7 Pro x64 Our current group policy uses a custom ADM file to define certain properties of the desktop (Background Image (centered), Background Color is green (00 74 00)). This policy works for us, but the down-side is that policies defined in our custom ADM are only applied after a GPUpdate /Force is applied. We would like these desktop theme settings to be applied the first time the user logs onto the computer. I've been working on a new policy that forces the computer to wait for the network when the user logs on to handle folder redirection. The reason for writing the new policy was to resolve the issue that a user needs to run GPupdate /Force the first time they log in, so it doesn't make sense for me to implement the new policy if there is still something that requires GPUpdate /Force to get the user in the state that we want them. I've moved the setting for background image out into Admin Templates- Desktop- Desktop- "Desktop Wallpaper" so this is now being set properly when the user first logs in. Now I'm left with a black background until I force a group policy update. I have tried to play around with setting a default "Theme" and had limited success; this was not reliable enough to call a solution. I suppose I could set the background color with a script? Any thoughts? It feels like I'm missing something obvious, or that this should be much easier than it is.

    Read the article

  • SQL Server Agent refuses to start

    - by Geo Ego
    I'm having a problem with SQL Server 2005 where the SQL Server Agent suddenly refuses to start. If I attempt to start it through Services, I get the error "SQL Server Agent (MSSQLSERVER) service on Local Computer started and then stopped." In the Application log, I have the following entry: Event Type: Error Event Source: SQLSERVERAGENT Event Category: Service Control Event ID: 103 Date: 5/20/2010 Time: 11:07:07 AM User: N/A Computer: SHAREPOINT Description: SQLServerAgent could not be started (reason: Unable to connect to server 'SHAREPOINT'; SQLServerAgent cannot start). This database has been running fine for four months. It contains a SharePoint configuration database, which two days ago stopped working, throwing me a message that the configuration database cannot be reached. It was then that I realized the SQL Server Agent was not running, and I have been unable to restart it. I have tried running it with both the local system account and the network service account, with the same results. So far, I have tried: Granting the administrators group, network service, and SharePoint SQL Server Agent account public and sysadmin roles on the database. Granting the administrators group, network service, and SharePoint SQL Server Agent account full permissions to the entire MSSQL directory and all files within. I still have no joy.

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • Is it possible to stop the "Beep" device on all computers in a Windows network?

    - by sharptooth
    On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

    Read the article

  • Vista WHS Client stopped resolving local names

    - by andrewcr
    I’m running Windows Home Server PP2 in my home, with 3 client computers: two XP and one Vista. I have a router that provides my local DHCP and the server has a static IP address. The other day the Vista machine hung, and on reboot stopped resolving local names. It will show the green home server client icon in the system tray, but if I attempt to log in to the console, I get a “This computer cannot connect to your home server” message. If I ping the server name from the command line, it does not resolve, and gives a “could not find host” message. Oddly enough, if I browse the network, I can see the server, but double clicking on it fails. The other machines on the local network have no problems seeing the server, and the Vista machine has no problems resolving names from the internet, it just can’t see any local machines. I’m aware that I can work around this by adding entries to my HOSTS file (it does work), but I’d like this to work the way it’s “supposed” to. I’m an experienced computer user and developer, but not a networking whiz. Can anyone tell me how local name resolution is supposed to work in my environment and/or suggest ways to troubleshoot this? Thanks, Andy

    Read the article

  • Cache updates when migrating DNS from one provider to another

    - by JohnCC
    This may be a Windows DNS specific question or a general DNS best practice question - I'm not sure! We migrated our 3rd party DNS provision from provider A to provider B. I noticed that our internal recursive windows DNS servers still had NS records cached for our domains pointing to provider A's servers, even though I changed the nameservers with our registrar several days ago, and even though selecting the properties of the cached records showed a TTL of 1 day. After 24 hours when the NS records in this cache have expired, will the DNS server go back to the TLD server for an update on the authority, or will it go by preference to dns1.providera.com since that is what it has cached? In this case I arranged to leave Provider A's servers up for a week to allow changes to propagate, so dns1.providera.com is still active and would still provide NS and SOA records that said that dns1.providera.com. was in charge of this domain. Given this fact, would the Windows DNS server ever go back to the TLD and pick up the authority changes, or would it just assume all was well and renew timestamps on its cached NS records? I wonder what would be the best approach to ensuring that caches pick this up. Should I:- (1) Leave Provider A's servers in place and active and wait for caches to catch up ... basically what we're doing now which seems to have issues - perhaps specifically for Windows servers, or perhaps more widely. (2) Leave Provider A's servers in place but change the NS and/or SOA information they provide to tell caches that new servers are in charge. (3) Remove Provider A's servers after 2*TTL to force remaining caches to update. The issue with (2) is that on Provider A's system I can't seem to change the NS or SOA information to anything other than their servers. The issue with (3) is that I'm not sure how a DNS server would behave in this case. When it couldn't reach the cached name servers, would it flush its cache and try a full recursive lookup, or would it just return an error, forcing the user to clear the cache manually? Thanks in advance!

    Read the article

  • Choose identity from ssh-agent by file name

    - by leoluk
    Problem: I have some 20-30 ssh-agent identities. Most servers refuse authentication with Too many failed authentications, as SSH usually won't let me try 20 different keys to log in. At the moment, I am specifying the identity file for every host manually, using the IdentityFile and the IdentitiesOnly directive, so that SSH will only try one key file, which works. Unfortunately, this stops working as soon as the original keys aren't available anymore. ssh-add -l shows me the correct paths for every key file, and they match with the paths in .ssh/config, but it doesn't work. Apparently, SSH selects the indentity by public key signature and not by file name, which means that the original files have to be available so that SSH can extract the public key. There are two problems with this: it stops working as soon as I unplug the flash drive holding the keys it renders agent forwarding useless as the key files aren't available on the remote host Of course, I could extract the public keys from my identity files and store them on my computer, and on every remote computer I usually log into. This doesn't looks like a desirable solution, though. What I need is a possibility to select an identity from ssh-agent by file name, so that I can easily select the right key using .ssh/config or by passing -i /path/to/original/key, even on a remote host I SSH'd into. It would be even better if I could "nickname" the keys so that I don't even have to specify the full path.

    Read the article

  • Dual boot windows 8 pro and windows 7 on XPS 8500 Special Edition

    - by Jesse
    I am trying to install a dual boot with windows 7 premium and windows 8 Pro on an XPS 8500 special edition. I created a new primary partition on my C: drive, inserted the windows 8 install disk, and rebooted my computer from DVD. I select custom install and the dialog box saying "Where do you want to install windows at?" pops up but none of my drives are listed. Please help me determine what is going on. I don't understand why none of my drives are showing up on this menu. Not even the original drive. When I go to load driver and click on the partition I created it tells me "No signed device drivers were found. Make sure the installation media contains the correct drivers, and then click OK." resolved above issue by running setup from the source folder on the install disk instead of booting from DVD. Was able to locate my new partition and start install. It completes the first step of "Copying windows files" just fine but then on the next step "Getting files ready for installation" my computer restarts and attempts to load windows 8 but keeps telling me my pc needs to restart. This keeps going on in an infinite boot loop. Please help, this has been a nightmare!

    Read the article

  • Very slow connection to xserve via afp or smb

    - by Mhoffman13
    Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

    Read the article

  • Cannot ping Google Public DNS on 8.8.8.8

    - by Tibor
    I have a weird problem on my Windows 7 (x64) computer. I seem to cannot ping the Google Public DNS on one of its addresses (while the other works fine). The peculiar thing is that it fails with the General failure. error message which usually means that there is a problem with a network adapter/base connectivity and not a timeout as one would expect. I checked my routing tables for any anomalies and I even flushed them but the problem seems unrelated. All the other hosts I tried ping fine (either respond or timeout). If I try to tracert or connect to the address via browser (yes, I know that it doesn't listen on port 80), it also fails instantaneously. The reason I need to ping 8.8.8.8 is that I commonly use it as a test of Internet conectivity due to it being rememberable. The problem occurs no matter where I connect to the Internet (it is a laptop computer). What could be the cause of this anomaly? Note: I use native IPv6 connectivity.

    Read the article

  • Access Windows Boot Manager selector when timeout is set to 0?

    - by Kyle Cronin
    I've installed Wubi onto a Windows Vista computer. I've also set the boot timeout to 0: bcdedit /timeout 0 However, now I can't figure out how to get the menu to come up at all! I read on the internets that I had to hold F8 or space when starting up, but they doesn't seem to do anything. Is there a different key or setting I've overlooked? The computer itself is a Dell that's a few months old. The keyboard is USB, but I don't think that's the problem as I can get into the BIOS just fine. Maybe I'm doing it wrong? Am I supposed to hold the keys or rapidly tap them (I've tried both)? If it helps, here's the output from bcdedit: C:\Windows\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=C: description Windows Boot Manager locale en-US inherit {globalsettings} default {current} resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} displayorder {current} {e2484fe7-5e97-11de-84d4-0024e8074422} toolsdisplayorder {memdiag} timeout 0 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Windows Vista locale en-US inherit {bootloadersettings} recoverysequence {572bcd55-ffa7-11d9-aae0-0007e994107d} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} nx OptIn Real-mode Boot Sector --------------------- identifier {e2484fe7-5e97-11de-84d4-0024e8074422} device partition=C: path \ubuntu\winboot\wubildr.mbr description Ubuntu

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • How to get multipath working for Ubuntu Server 12.04

    - by mlampi
    I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

    Read the article

  • Unix Permissions: Enable access to files no matter the user?

    - by TK Kocheran
    I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

    Read the article

  • IIS 7.5 Siteminder is not protecting ASP.net MVC requests

    - by HariM
    We are trying to use ASP.Net MVC with Siteminder for Single Sign on. This is on Windows Server 2008 R2 with IIS 7.5. Siteminder Agent version 6QMR6. Problem : Siteminder protects physical files that are exist. And it is not protecting the folder when we try to access a non existed file. It must redirect to login page even if the file doesn't exist when the user is accessing a protected folder. How to configure in IIS 7.5 that Do not verify a file exist, before authentication by siteminder. SiteMinderWebAgent is a Handler(WildCard Script Map) we created using the ISAPI6WebAgent.dll How to Protect ASP.Net MVC Request with Siteminder? (Added this as My previous question did not solve the problem). MVC Request shows up in IIS Log but not in Siteminder log. Update : Microsoft Support says currently IIS7.5, even in earlier versions doesnt support wildcard mappings on any two Isapi Handlers with * wild card. Currently in my case Siteminder has * wildcard and asp.net mvc (handler is aspnet_isapi) has * wildcard to handle the reqeusts. Ordered priority doesnt work in the wild card mappings case with Just *. Did not convinced with the answer but will wait till tomorrow for them to get back.

    Read the article

  • Windows XP error message: "Windows cannot find 'explorer.exe'"

    - by Meysam
    In Windows XP I can open "My Computer" and see all the hard drives. I can also see the explorer.exe process running among other processes in Task Manager. But after opening "My Computer", when I double click on one of the drives to open it, I get the following error message: Windows cannot find 'explorer.exe'. Make sure you typed the name correctly, and then try again. To search for a file, click the start button, and then click search. Although I could detect and remove several suspicious files using Malwarebytes & Microsoft Security Essentials, the problem still remains. The interesting point is that if I right click on one folder and select Open or Explore from the menu bar, I can open the folder! but if I double click on the folder, it does not open and I get the above error message. How can I fix this problem? Any advice would be appreciated! Update: I formatted the C: drive (NTFS), a deep format, and installed a fresh Windows XP on it. I am not getting this error when I double click on C drive icon anymore. But the same error appears when I double click on other drive names. Maybe I should format them too!

    Read the article

  • HAProxy "503 Service Unavailable" for webserver running on a KVM virtual machine

    - by Menda
    I'm setting up a server with KVM (IP 192.168.0.100) and I have created inside of it one virtual machine using network bridging at 192.168.0.194. This virtual machine has an nginx instance running, which I can access from the server or from any computer computer in the internal network just typing in the browser http://192.168.0.194. However, I try configure HAProxy in the same server that hosts KVM and looking the status page of HAProxy it always shows the virtual machine as "DOWN". If I try from the server http://localhost, it should be the same than if I go to http://192.168.0.194. My goal is to build a reverse proxy, but I tried this little example and won't work. What am I doing bad? This is my config file in the server: # /etc/haproxy/haproxy.cfg global maxconn 4096 user haproxy group haproxy daemon defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen ServerStatus *:8081 mode http stats enable stats auth haproxy:haproxy listen Server *:80 mode http balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /check.txt HTTP/1.0 server mv1 192.168.0.194:80 cookie A check Thanks.

    Read the article

  • Mac Grey/White Screen of Death

    - by cust0s
    The other night I updated my iTunes to the latest version (through Software Update) when I came to turn on my computer I was greeted with the dreaded white screen of death. I use an early 2008 iMac 24". I've tried the basic things, unplugging/turning off accessories, trying to boot from the install disk, reseting pram, etc, etc. Still no luck and no change what-so-ever. All I've been able to ascertain that my keyboard still works (by ejecting). I should point out that I did recently replace my Hard drive with a Western Digital Black 500GB (though the computer is well out of warrenty) and I'm a little concerned that the problem could be the screen. Update (18/05/10): I've been told that I could be getting the White/Grey screen of death because the optical flex cable is damaged (aparently this is common). Apparently the Optical Drive is part of the POST sequence, and an inability to read the drive can result in failure for the system to move on to other bootable volumes. More info here. I will disable the optical drive and see if that works.

    Read the article

  • Convert a cassette tape recording to digital format

    - by Electric Automation
    Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

    Read the article

< Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >