Search Results

Search found 37931 results on 1518 pages for 'computer case'.

Page 408/1518 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

• Cannot connect to windows server by name over vpn connection

  - by ErocM

  I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

  Read the article

• Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

  - by SuperUserMan

  Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

  Read the article

• Can't create add a SQL Server user: The login already has an account under a different user name.

  - by Zian Choy

  Environment: SQL Server 2005 Express Windows 7 When I installed SQL Server, I followed the instructions at http://msdn.microsoft.com/en-us/library/aa905868.aspx to set my computer's admin account as the SQL Server admin. However, when I try to access a database on my computer through Visual Studio 2008, I get the following error message: --------------------------- Microsoft Visual Studio --------------------------- The database 'Parkinsons' does not exist or you do not have permission to see it. Would you like to attempt to create it? --------------------------- Yes No --------------------------- Then, if I go to SQL Server and add a user to that database, I get the following error message: TITLE: Microsoft SQL Server Management Studio Express ------------------------------ Create failed for User 'zian'. (Microsoft.SqlServer.Express.Smo) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=9.00.2047.00&EvtSrc=Microsoft.SqlServer.Management.Smo.ExceptionTemplates.FailedOperationExceptionText&EvtID=Create+User&LinkId=20476 ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.Express.ConnectionInfo) ------------------------------ The login already has an account under a different user name. (Microsoft SQL Server, Error: 15063) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=09.00.4053&EvtSrc=MSSQLServer&EvtID=15063&LinkId=20476 ------------------------------ BUTTONS: OK ------------------------------ Why doesn't VS piggy back on the dbo account? If the dbo account is unusable, then why won't SQL Server let me make an account so that I can access my own data?

  Read the article

• I can play "test" sounds, but no other audio works

  - by Callum

  I'm running Windows XP, and last night my PC was infected by a frustrating virus (one of those viruses that won't let you open virus checkers, etc). I finally killed it 2 hours later, but it involved some heavy duty anti-dote. One side effect is my audio is now gone. Except it's not entirely gone, because when I open the Realtek HD Audio Manager in the task bar, I can play all the "test" sounds. The speakers, the sound card, etc, are therefore working fine. But things like YouTube or Windows Media Player, there's no sound. I'm guessing there's a setting that needs to be reconfigured somewhere.. but where? Maybe relevant: One thing I did do last night was "play" with the system registry. Any help would be greatly appreciated. Thanks. SOLVED! The two hour battle with my computer virus resulted in my computer permanently thinking it was in Safe Mode, regardless of how it booted up. I was able to "fix" this by following the post by hsandler in this thread: http://www.petri.co.il/forums/showthread.php?t=23032&page=2 I then rebooted.. and let me tell you, the Windows Startup music has never sounded so sweet. Thanks to all, especially James, whose advice gave me a major clue as to what the problem was.

  Read the article

• Options for small windows network setup without dedicated server?

  - by Mitch

  I'm very weak on networking and hope someone can point me in the right direction: I have written some windows client/server software which incorporates a database which is located on a windows server. I have a test installation running at a customer's office where the server has a static IP address. In this case its easy for the clients to access the database because of the fixed IP address. Also, customers with network servers generally have specialist support staff to set up my software, so its not such a problem for me. However I also need to offer the software to customers who have small offices with less than 10 PCs and no dedicated network server. In this case I want the customer to be able to nominate one PC as the database "server" and install my software and have the clients access it. But in this situation I believe the "server" PC may not have a dedicated IP address. Q1: What is the best way to set this up simply and make it work? Can I reliably reference the "server" by using its name, or is there a way to assign dummy fixed IP addresses? Ideally this needs to be workable on small networks running a mixture of XP/Vista/Windows7 as my target market may well have mixed OSes etc. I guess this would be akin to home networking? Many thanks Mitch

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• XP SP2 Event log not logging events

  - by Weedfreer

  I have a problem whereby a terminal appears not to be logging events correctly and occasionally appears to have problems communicating accross the network.The terminal has previously been infected with a virus which apears to have 'played' with the default group policy in the standard user profile. Although, outwardly, the terminal appears to be working normally I still have a nagging feeling that it isn't quite back to the way it was. It was infected by a user plugging in a USB Stick while the company was using the older version of the AV software...typically a week or so before it was updated.I have configured the Event logs to Overwrite as required and to be 5056KB in Maximum size. I have also attempted:- Disabling the Event Log service & restarting Renewing the EVT files in Windows\system32\config directory Restarting the event log service and restarting Clearing the event log in the Services MMC Resetting the Filters to Default in the services MMC Using the EVENTCREATE command remotely from a CMD window on the server to force an event creation event. So far the only operation to have any sort of success is the remote computer EVENTCREATE command from a CMD window on the server. As it stands, the only other time that the computer has managed to create events is while it is being restarted.Has anyone gotany ideas on how to proceed? I'm thinking that possibly a refresh of the 'Windows\system32\config\SystemProfile' folder. I'm also thinking about running a tool such as Malwarebytes but this could be slightly controvertial as the system needs to be running on 'up-time' for as long as possible. I'm also wonderign whether anyone knows of any Windows admin tools that allow me to control the event logging options or default security options so that i could get it back to some sort of standard.What I'm trying to avoid is a complte re-imaging of the terminal. Although this is an option, I dont really want to have to take it if i dont need to.Many thanks in advance for any suggestions anyone may be able to provide.

  Read the article

• Vista - Profile not Loaded Correctly (Cannot Access Registry)

  - by Geoff

  Every so often, I log on and get the Following Message: User profile was not loaded correctly. You have been logged on with a temporary profile. Changes you make to this profile will be lost when you log off. Please see the event log for details or contact your administrator This almost always happens when somebody else has been on the computer for a while, and then I log on. This never used to happen, but now it happens pretty often. My profile is not permanently corrupted, all I have to do is restart my computer, but this annoys me, and I would like to fix it. I was curios about the reason of this cause, so I looked into the Event Log, and found the root of the problem was the ntuser.dat file in the profile that I was logging on to was locked at logon time. This resulted in the current users registry not being loaded, resulting in failure to load the profile. What could be locking this file? is there any way to get a process list without logging on so that I can identify which process has the file locked? Any other suggestions. Hopefully I can find a solution.

  Read the article

• Is there a way to run CUDA applications with the CUDA device being a secondary adapter?

  - by Slartibartfast

  I've been trying to run a CUDA program on a remote computer which has Windows 7 installed. The GPU is GeForce GTX 480. One of the problems I've been facing is that, the computer has two adapters, 1) Standard VGA Adapter 2) NVIDIA GeForce GTX 480 Even though this shows in the device manager. The desktop uses the standard VGA Adapter. I'm assuming this is because the Standard VGA is the primary adapter. Also the device manager shows that the monitor is connected to the standard VGA Adapter. In this scenario if i try to run any CUDA application it fails to recognise a CUDA capable device. Is it necessary for the NVIDIA adapter to be the primary one? Or is there any way to use CUDA when the graphics card is a secondary adapter. I've seen a few posts in the NVIDIA forums on this before, one suggests using another low cost NVIDIA card as the primary adapter, but that is currently not an option. I couldn't find any other solutions. Thanks I tried running the deviceQuery test from the NVIDIA GPU Computing Samples. This was the result i obtained CUDA Device Query (Runtime API) version (CUDART static linking) cudaGetDeviceCount FAILED CUDA Driver and Runtime version may be mismatched FAILED The driver version I'm using is 263.06. The CUDA version is 3.2 I ran the same test on my desktop which also has windows 7 and a GeForce GTX 465. The CUDA toolkit version is 3.2. The driver version was the same and the test passed, although it failed with an older driver.

  Read the article

• Cannot Access Shared Folder From IIS

  - by Tim Scott

  From IIS I need to access a folder on another computer. Both servers are Window 2008 SP2, and they live in a Virtual Private Cloud on Amazon EC2. They reach one another by private IP -- they are in WORKGROUP, not a domain. I can access the shared folder manually when logged in to the client as Administrator. But IIS gets "access denied." Here's what I have done: Set File Sharing = ON Set Password Protected Sharing = OFF Set Public Folder Sharing = ON Shared the folder Added permission to the share: Everyone, Full Control Added permission to the share: NETWORK SERVICE, Full Control Verified that File & Printer Sharing is checked in Windows Firewall Opened port 445 to inbound traffic from local sources I tried adding <remote-machine-name>\NETWORK SERVICE to the share but it says it does not recognize the machine, which makes sense, I guess. As I said, from the other computer I have no trouble accessing the shared folder from my user account, but IIS is shut out. How does the file server even know the difference? I would assume that with Everyone given full control and password protected sharing turned off, it would not matter what the client user account is. In any case, how to solve? UPDATE: To clarify, I am not trying to serve up files on the share directly through IIS. Rather I am writing files to the share from my code (System.IO).

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• How to pass alias through sudo

  - by Tanktalus

  I have an alias that passes in some parameters to a tool that I use often. Sometimes I run as myself, sometimes under sudo. Unfortunately, of course, sudo doesn't recognise the alias. Does anyone have a hint on how to pass the alias through? In this case, I have a bunch of options for perl when I'm debugging: alias pd='perl -Ilib -I/home/myuser/lib -d' Sometimes, I have to debug my tools as root, so, instead of running: pd ./mytool --some params I need to run it under sudo. I've tried many ways: sudo eval $(alias pd)\; pd ./mytool --some params sudo $(alias pd)\; pd ./mytool --some params sudo bash -c "$(alias pd)\; pd ./mytool --some params" sudo bash -c "$(alias pd); pd ./mytool --some params" sudo bash -c eval\ "$(alias pd)\; pd ./mytool --some params" sudo bash -c eval\ "'$(alias pd)\; pd ./mytool --some params'" I was hoping for a nice, concise way to ensure that my current pd alias was fully used (in case I need to tweak it later), though some of my attempts weren't concise at all. My last resort is to put it into a shell script and put that somewhere that sudo will be able to find. But aliases are soooo handy sometimes, so it is a last resort.

  Read the article

• NAT vs public IP (and blocked ports)

  - by user1646166

  I have a problem with my ISP. They say that they don't block any ports and I have public IP, while I think these both statements are false. Before I talk to them again (which is really tough when my understanding of these terms is different than theirs) I would like to make some things clear. It seems like my computer is behind NAT (is it possible to have public IP and be behind NAT at the same moment?). When I check my IP, through some external server, and type that IP into browser I get a home page of some router (not mine). Isn't that a proof that my IP isn't public? Also, I have problems with making connections via some ports. E.g. when I'm trying to connect through some high port ( 1023) via SSH, it doesn't work. Is it possible that certain range of outgoing ports from my computer are blocked? Or is it simply because that my ssh client (PuTTY) can't receive incoming packets because of blocked incoming ports? To avoid some questions: it's not a problem with my router, I tried connecting my PC directly and it also didn't work, while having connected by 3G using phone with USB tethering, it does work. Thanks!

  Read the article

• How do I setup routing for 2 companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: 2 companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants it's own Internet connection (ISP A) and company B wants it's own Internet connection (ISP B). VLANs are deployed internally to separate the 2 company's networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I setup policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• Convert a cassette tape recording to digital format

  - by Optimal Solutions

  Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

  Read the article

• Outlook won't re-connect to exchange after network is re-connected

  - by stan503

  I have a setup at my desk where I connect my computer to a an RJ45 switch that switches between two networks. One network is the corporate network, which is maintained by my company's IT, and the other is my own private network where I do testing (the two networks have to be separated). The corporate network hosts the exchange server where I get e-mail. When I switch from the private network to the corporate network, I expect Outlook to re-connect to the exchange server. However, I have found that sometimes when I come back, Outlook take an extremely long time to re-connect. Send/Receive will give me back the error 'The server is not available' (0x8004011D). It will sit there for 10 minutes to a few hours before it finally re-connects. The only other option is to reboot my computer, which is a huge pain for me since I run multiple VMs on it. This usually happens when I'm connected to the private network for a significant amount of time, so I'm thinking it's because Outlook has cached the network status. Is there a way to force Outlook to do a 'hard' re-connect to the exchange server? I'm using Windows XP SP 3 with Outlook 2007.

  Read the article

• Windows 7 Aero theme's "greyed out" - no found fix

  - by Robsta

  Brand new machine that was working fine then randomly it changed the theme when I booted into a sort of "basic" theme (white task bar, no see through windows etc) I've done and attempted many fixes and I still don't understand why it doesn't work. I've tried these two solutions: "How to enable Windows 7 Aero Theme" and "Windows 7 Aero Themes Greyed out" These solutions included registy changes, stopping/starting services, and force starting the aero theme. The closest I got seems to be when I went into: Control panel (category view) Find and fix problems (System and Security) Display Aero Desktop Effects I follow through the wizard and let it do its thing and then I get an error window that pops up: Personalization - "This theme can't be applied to the desktop. Try clicking a diffrent theme." That's what I get from the wizard. What can I do? My drivers are all up to date, there are no viruses on the computer, directx is installed and updated, and the registry is all correct. EDIT: When I boot the computer, I get a notification stating that windows failed to communicate with the windows desktop services.

  Read the article

• How can you connect to a SQL Server not on your domain?

  - by scotty2012

  I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

  Read the article

• Sometimes, Synaptics Touchpad Tends Cursor to Top-Right Corner

  - by John Chadwick

  This has been a reoccurring issue for me, pretty much since I've owned this laptop (an ASUS G60JX.) Sometimes, the cursor will stop working properly and instead tend toward the top right of the screen. Basically, sometime into my usage (maybe after a couple hours) the touchpad will inevitably begin to malfunction, where it has confusing patterns of pushing the mouse cursor toward the top right of the screen. In addition, certain features (like momentum) seem to quit working entirely. It makes using the cursor extremely difficult. I've been having this issue across very many drivers. Pretty much as soon as multitouch came into the mix, although I don't believe multitouch has anything to do with it. It appears that, in the state of malfunction, it doesn't matter how you touch the touchpad, but where you touch it. Certain regions do not seem to trigger the cursor to move to the top right corner. In fact, no specific region seems to, but some areas do so more often than others. The issue can be resolved temporarily by putting the computer into sleep mode and awakening it. I have found no way to recreate this success without sleeping the computer or rebooting. Disabling and re-enabling the touchpad device does not do anything to resolve the problem. This issue does not affect my WACOM tablet nor any USB mice, and can be resolved (not to my satisfactory) by uninstalling the touchpad drivers. I'm looking for a solution, or at least a workaround that doesn't require sleep mode.

  Read the article

• Would an invalid certificate cause an 0x8004010F sync error?

  - by hydroparadise

  We just migrated from Exchange 2003 to 2007 which was a combo primary AD/DNS server and it has not gone smoothly. We are now down to getting a new certificate (a bureaucratic process thats out of my hands) and users getting the 0x8004010F sync issue. We are only using Outlook 2007 as our email client and the sync error appears exactly as so: 9:21:44 Synchronizer Version 12.0.6562 9:21:44 Synchronizing Mailbox '<User>' 9:21:44 Done 9:21:44 Microsoft Exchange offline address book 9:21:44 0X8004010F Now, I have read a number of technet articles on this issue anywhere from adding an A record in the DNS for autodiscover.domain.com to syncing the old OAD to the new OAD. In otherwords, theres lots of thing to try, but trial and error at this point might be hazardous to ther server's health and I am trying to narrow down the list of things to try. What has me thinking that the sync error could be related to the certificate is an event error message that says the following: Microsoft Exchange could not find a certificate that contains the domain name mail.ccufl.org in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Internet Mail with a FQDN parameter of mail.ccufl.org. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. I am not fully clear on how the Exchange Transport Service is related to Syncronization, but my hunch is that it probably not related to there not being a valid certificate. So to recap, would an invalid certificate cause an 0x8004010F sync error?

  Read the article

• Configured Samba to join our domain, but logon fails from Windows machine

  - by jasonh

  I've configured a Fedora 11 installation to join our domain. It seems to join successfully (though it reports a DNS update failure) but when I try to access \\fedoraserver.test.mycompany.com I'm prompted for a password. So I enter adminuser and the password and that fails, so I try test.mycompany.com\adminuser and that too fails. What am I missing? EDIT (Update 9/1/09): I can now connect to the machine and see the shares on it (see my response to djhowell's answer) but when I try to connect, I get an error saying The network path was not found. I checked the log entry on the Fedora computer for the computer I'm connecting from (/var/log/samba/log.ComputerX) and it reads: [2009/09/01 12:02:46, 1] libads/cldap.c:recv_cldap_netlogon(157) no reply received to cldap netlogon [2009/09/01 12:02:46, 1] libads/ldap.c:ads_find_dc(417) ads_find_dc: failed to find a valid DC on our site (Default-First-Site-Name), trying to find another DC Config files as of 9/1/09: smb.conf: [global] Workgroup = TEST realm = TEST.MYCOMPANY.COM password server = DC.TEST.MYCOMPANY.COM security = DOMAIN server string = Test Samba Server log file = /var/log/samba/log.%m max log size = 50 idmap uid = 15000-20000 idmap gid = 15000-20000 windbind use default domain = yes cups options = raw client use spnego = no server signing = auto client signing = auto [share] comment = Test Share path = /mnt/storage1 valid users = adminuser admin users = adminuser read list = adminuser write list = adminuser read only = No I also set the krb5.conf file to look like this: [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = test.mycompany.com dns_lookup_realm = false dns_lookup_kdc = false ticket_lifetime = 24h forwardable = yes [realms] TEST.MYCOMPANY.COM = { kdc = dc.test.mycompany.com admin_server = dc.test.mycompany.com default_domain = test.mycompany.com } [domain_realm] dc.test.mycompany.com = test.mycompany.com .dc.test.mycompany.com = test.mycompany.com [appdefaults] pam = { debug = false ticket_lifetime = 36000 renew_lifetime = 36000 forwardable = true krb4_convert = false } I realize that there might be an issue with EXAMPLE.COM in there, however if I change it to TEST.MYCOMPANY.COM then it fails to join the domain with a preauthentication failure. As of 9/1/09, this is no longer the case.

  Read the article

• Problem restoring from tar backup: why are there /dev/disk/by-id/ symlinks and how can I avoid them?

  - by SK.

  Hello, I'm trying to make a bare-bone backup system with the most basic tools available on openSUSE 11.3 (in this case: bash, fdisk, tar & grub legacy) Here's the workflow for my scripts: backup.sh: (Run from external system, e.g. LiveCD) make an fdisk script ($fscript) from fdisk -l's output [works] mount the partitions from the system's fstab [works] tar the crucial stuff in file.tgz [works] restore.sh: (Run from external system, e.g. LiveCD) run fdisk $dest < $fscript to restore partitioning [works] format and mount partitions from system's fstab [fails] extract from file.tgz [works when mounting manually] restore grub [fails] I have recently noticed that openSUSE (though I'm sure it has nothing to do with the distro) has different output in /etc/fstab and /boot/grub/menu.lst, more precisely the partition name is for example "/dev/disk/by-id/numbers-brandname-morenumbers-part2" instead of "/dev/sda2" -- but it basically is a simple symlink. My questions about this: what is the point of such symlinks, especially if we're restoring on a different disk? is there a way to cleanly prevent the creation of those symlinks and use the "true" /dev/sdx everywhere instead? if the previous is no, do you know a way to replace those symlinks on the fly in a text file? I tried this script but only works if the file starts with the symlink description (case of fstab, not menu.lst): ### search and replace /dev/disk/by-id/... to /dev/sdx while read oldVolume rest; do # get first element, ignore rest of line if [[ "$oldVolume" =~ ^/dev/disk/by-id/.*(-part[0-9]*$)? ]]; then newVolume=$(readlink $oldVolume) # replace pointer by pointee, returns "../../sdx" echo /dev/${newVolume##*/} $rest >> TMP # format to "/dev/sdx", write line else echo $oldVolume $rest >> TMP # nothing to do fi done < $file mv -f TMP $file # save changes I've had trouble finding a solution to this on google so I was hoping some of the members here could help me. Thank you.

  Read the article

• Get Internal IP Address From DHCP Hostname

  - by ell

  I would like to try and get an internal ip address of one of the computers on my network. The reason for this is I have a little home server box downstairs but every time I want to SSH into it I have to open my router configuration and go on the DHCP client table and look at the IP address. For example I would like to be able to go ssh ell-sever instead of ssh 192.168.1.105 or whatever it happens to be. My network configuration is like so: Router downstairs that is connected to the Internet and is running a DHCP server My server computer (ell-server) is a headless pc connected to the router via ethernet cable. Running Ubuntu 11.04 Server Edition My laptop upstairs (ell-laptop) that is running Ubuntu 11.10 Desktop Edition connected wirelessly Other (irrelevant) computers - 2 x Windows XP, 1 x Xubuntu - all connected with cables. (It seemed to me the method of connection isn't useful information but I put it in anyway - just in case. If I have missed any information please tell me) Do I have to run a DNS server on one of my computers? If so which one? And does that mean I will have to run a DDNS client on each computer? Thanks in advance, ell.

  Read the article

• Maintaining "Portability" Between Linux and Windows 7

  - by lokheart

  I am using the following ways in my office's Windows 7 machine to maintain my "portabilibity" when disaster strikes and I need to switch computer while I have no luxury of time for reinstalling all my program to the new PC. a majority of programs I used are portable, mostly from portableapp.com, like notepad+, GIMP, even R, I extract them and store them in a folder in My document, in a structure similar to the default portableapp installation when they are installed to a thumbdrive only a few software that portable version is not available and I will install them as usual all of my working files are stored in a folder in My document I regularly backup them all using syncback, because this program can keep versioning of my backup, and the backup is stored in a portable drive. One day I need to switch my computer and the operation is relative simple for me: I just move the two folders mentioned above into the my document folder of the new PC, install those few "non-portable" program in it, and this is almost done, some minor hiccups can be solved by reinstalling the portableapp into the drive. Overall speaking it is a smooth process. I would like to maintain the same degree of "portability" in my home Linux desktop (Ubuntu or Mint, I'm still deciding), that is, if my Linux crash and I need to reinstall it again. All I need to do is the move the two folder back to the new Linux, and most of my work will be almost ready to be worked on again. But I don't know how to find a Linux-alternative of portableapps. Being a newer to Linux, can anyone tell me whether this is possible in Linux?

  Read the article

• Is USB supported in safe mode on XP?

  - by Hugh Allen

  According Microsoft, "Universal Serial Bus Devices Do Not Work in Safe Mode" under XP. However, in my testing this is incorrect. USB keyboards, mice and flash drives seem to work fine in safe mode (I made sure the BIOS was not providing support). This makes sense because a failure of a standard input device would be, in Microsoft parlance, a "bad user experience". So, Is USB supported in safe mode on XP? If your answer is no (agreeing with Microsoft), please provide a test case, preferably in a virtual machine, where a standard HID keyboard or mouse fails. Please state hardware / BIOS / OS configuration. Note that you will need a PS/2 keyboard attached in addition to your USB device(s) in order to use the boot menu. Virtual machine software usually emulates a PS/2 keyboard. Alternatively, you could add the /safeboot switch to boot.ini. If your answer is yes, please provide a link to some supporting documentation (either from Microsoft or someone authoritative). Your answer might be "devices X, Y and Z are supported but nothing else", in which case also give a link.

  Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >