Search Results

Search found 92314 results on 3693 pages for 'user unknown'.

Page 409/3693 | < Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >

  • Upgrading memory in a laptop

    - by ulidtko
    I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

    Read the article

  • dell latitude XT touch screen issue

    - by Jake
    yesterday I installed windows 7 ultimate after I had the enterprise version on this machine for a few months. the installation went smoothly and everything worked fine except for the finger detection of the screen(only the pen worked) and the bottom screen buttons for rotating and so. so I started to install all the missing drivers dell recommends for this model on their site, but once I tried to install N-Trig degitizer driver the installation said it was unsuccessful and since then the touch stopped working completely! I tried system restore but it didn't help so I went on and formatted the harddisk completely once again and installed windows but that didn't work either. I tried to install the N-Trig's driver but it was alarting for a fatal error and said that no device was detected. same story with N-Trig rollback. so I checked the device manager and saw an "unknown device" with VID and PID values set as 0000. I figured the N-Trig driver might have messed with the device firmware or something and now it doesnt know it's ID and munufactor... Is there anything that can be done? like forcing the N-Trig driver to install on this device or something? please help!

    Read the article

  • How can I use an own asp page as 404 error page on a Windows 7 pro IIS 7.5 local installation

    - by Edelcom
    Running Windows 7 Pro Running local IIS 7.5 ( for web development purposes ) Edited hosts file to be able to use http://www.sitestepper.dev Site build in subfolder of the inetpub/wwwroot/staplijst Site can be viewed using http://www.sitestepper.dev/staplijst/whatever-page.htm I have an http://www.sitestepper.dev/p.asp page I would like to call when an unknown page is requested. This technique works fine on the deployed version of this web site ( deployed on an Windows 2003 server running IIS 7 - not sure about the 7 but it is the version deployed with Windows 2003 server ). I tried ( in the Edit Custom Error Dialog ) : Execute a URL on this site: with value /staplijst/p.asp and Respond with a 302 redirect: with value http://www.sitestepper.dev/staplijst/p.asp I tried this in the properties of the 'Default Web Site' , and I tried this at the staplijst level. Even tried it with values without the /staplijst. I restarted the default web site after each change. And even stopped/started the Web service. But nothing seems to work, I keep getting the 'Server Error In Application "DEFAULT WEB SITE"' , HTTP Error 404.0 error. What am I missing here - probably something obvious, but I don't see it ? Thanks in advance

    Read the article

  • Find whether TV supports S Video

    - by Vik
    Hello Freinds I have a TV (some unknown model) which has 3 sockets to insert 3 wires red, yellow and white. A DVD Player can be connected to the TV using sockets and the TV displays that the TV is in AV mode when DVD is running. Now i have a Desktop which has a S Video Port and i have a wire to connect the S Video port from my computer to those red, yellow and white sockets using appropriate pins. Now i have searched all over the remote and it does not switches to S Video Mode, it has only 2 modes of operation i.e. 1 Cable Connection (Third Party DTH Receiver receives channels and i pay subscription) and 2 AV Mode. It does not have S Video Mode or any other mode. Now my question is whether i can connect the S Video cable from my desktop to the above described TV or i should look for a new TV if i wish to connect the S Video from Computer to TV or there is any sort of converter that can help? I did tried connecting the S Video cable from Desktop to TV, but it did'nt worked. TV kept on displaying Blue Screen of AV Mode. Regards

    Read the article

  • How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

    - by Todd V. Rovito
    I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

    Read the article

  • The BitLocker encrypted logical drive of my laptop is not accessible. On clicking error appears,"Application not found"

    - by Nauman Khan
    I had an important personal data that was stored in my laptop drive 'F'. My 4 year old son also uses my laptop to play games. To secure my data I used bitlocker software that was already there in my windows 7 ultimate 32 bit. I am using a Dell D 630 Core2Duo laptop. The thing worked fine for me and I have been able to access my data in drive 'F' as and when I required. But today, when I tried to open my 'F' drive, an error box appeared saying "Application not found". I right clicked and checked 'properties' of 'F' drive. It showed me Used Space = 0 bytes and Free Space = 0 bytes. I opened 'Disk Management' which showed my 'F' drive file system as 'Unknown (Bitlocker Encrypted). 'Disk Management' is also showing my 'F' drive as healthy logical drive. I opened 'Manage bitlocker' and found that my 'F' drive was being shown locked and 'Unlock Drive' was displayed against it, however, when i click on 'Unlock Drive', it does not function. I opened 'TPM Administration' and found an information that 'Compatible TPM cannot be found'. My bitlocker encryption was working fine which means that I had a compatible TPM in my laptop. Where has it gone? How can I enable it? Is my 'F' Drive lost forever and thus the data in there as well?

    Read the article

  • How to fix Truecrypt MBR using Command Prompt or Linux live USB?

    - by Michal Stefanow
    I was playing with TrueCrypt and decided to make a fresh installation of Windows 7 from USB stick. Unfortunately Windows 7 installer: "setup was unable to create a new system partition" My entire HDD has been formatted and is visible as 320GB unallocated space, but no fdisk nor Windows 7 installer nor Windows XP installer could help. (Windows XP doesn't even see the HDD, it sees only USB stick and says "not enough space to install") It may be related to Truecrypt and pre-boot authentification, boot loader and/or MBR. As I don't have optical device I could not have created rescue disk. Right now I need a rescue of some kind, supposingly by erasing/fixing MBR using Linux live USB or using Command Promt. Another approach is to click "repair your comuter" menu from Windows 7 installer then click "restore your computer", then click OK upon error and get access to Command Prompt. Yet another another approach is to start computer without Linux USB I receive this: error:unknown filesystem. grub rescue> Any help would be greatly appreciated as my laptop is kind of not fully operational now. UPDATE: This was asked long time ago, ended up formatting everything (eventually it worked using different bootable USB)...

    Read the article

  • How to resume XMPP groupchat window in Irssi (using bitlbee)?

    - by mcnesium
    I use Bitlbee to chat in XMPP-networks within my IRC-client Irssi. This works great so far, and recently I started using XMPP Multi User Chats as an alternative to IRC-channels. I set up a channel using chat add <account> <[email protected]> in the &bitlbee control window, set chan <room> set autojoin true and entered /join #room in the &bitlbee window to join that groupchat. It then appears as a unique Irssi window in the status bar. This seems to work ok too, but with one exception: Since I idle in the channels 24/7 my irssi has to cope with the every-night-24h-DSL-disconnection by the ISP. After it automatically reconnects, it does kind of rejoin that XMPP-groupchat, but the traffic of the groupchat does not go back to the unique irssi window, but keeps flooding &bitlbee with messages from root telling me about a Groupchat Message from unknown JID <jid>: <message> - which is the traffic of the groupchat. The unique groupchat window is gone after the reconnect, and I will again have to go /join #room in &bitlbee to get it back. Even worse, the window number is unused before I rejoin the groupchat, and if I get a query from any network, the window nests in that unused window spot, so I will first have to remove that query from the spot, and then move the rejoined groupchat to that window number. I want my groupchat window to resume after the reconnect just like every other IRC channel too. How can I get this done? Any ideas?

    Read the article

  • Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • How can I extract data from Toshiba Satellite with a dead Windows installation?

    - by msanford
    I've got a Toshiba Satellite (unknown model number but bought early 2010) running Windows Vista which throws a kernel error on boot. We don't have the restore/recovery CD any more to restore the Windows partition. I have managed to boot to a Live CD version of Ubuntu 10.10 and have mounted the internal hard drive (which takes nearly 8 minutes). I suspect that the hard drive is malfunctioning, however, because copy tasks of even 30 megs of data to an attached and mounted USB flash drive takes over an hour, and some files are mysteriously inaccessible (not a permissions issue). When browsing folders, it takes many minutes to populate the folder window even with a single tiny file. During the copy tasks, the hard disk sounds like it tries to sleep several times in rapid succession, then continues accessing, it sounds, at full throughput. I initially tried using scp (from the shell) to copy data but I encountered the same local problems. I don't know the S.M.A.R.T. status of the hard disk, either. Is there a more effective way of going about recovering the data on the internal disk, assuming that I can't use a recovery CD and am too cheap to bring it in (for now, at least)?

    Read the article

  • Utilu IE Collection IE6 crashes under Windows 7

    - by Aron
    I've installed Utilu IE Collection under Windows 7 64-bit, but am unable to successfully run IE6 (specifically, "Internet Explorer 6.0 (6.00.2900.2180)"). I haven't tried other versions of IE from the package, so their behavior is unknown. It starts up fine, but the address bar isn't shown. (Attempted to post image, but I'm a newbie on SU and it wouldn't let me. Can be found here.) View-Toolbars shows 'Address Bar' already selected. If I try to (de-)select Address Bar in that list, it crashes: Problem signature: Problem Event Name: APPCRASH Application Name: iexplore.exe Application Version: 6.0.2900.2180 Application Timestamp: 41107b81 Fault Module Name: StackHash_e162 Fault Module Version: 0.0.0.0 Fault Module Timestamp: 00000000 Exception Code: c0000005 Exception Offset: 00000000 OS Version: 6.1.7600.2.0.0.256.48 Locale ID: 1033 Additional Information 1: e162 Additional Information 2: e1625455580a00d3fda64a8cdf366fbb Additional Information 3: 58c7 Additional Information 4: 58c75753c6745fad91929ab6430a83fa That's not all that's wrong ('Search' pane has no contents as well, probably more), but it's the most glaring problem. I've seen some allusions to a registry change needed to fix this, but haven't been able to find any details. Anybody? I'm running the latest version of the collection, 1.7.0.6.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Windows Broken after Deletion of HP_TOOLS partition

    - by beanland
    When I decided to install Ubuntu on my laptop as a dual-boot, I recognized that Windows 7 was using four separate partitions. I (yes, this was stupid) thought the HP_TOOLS partition was probably one I could get rid of, so I deleted it and installed Ubuntu side-by-side Windows using the installation wizard, but now Windows won't progress past the loading screen without the computer automatically restarting. I've had to use Ubuntu exclusively since then. I'm not sure how I can recover it. All of my files seem to still be there--I can mount the other partition and see them, use them, etc--but Windows 7 won't boot. I really have no idea what to do or what to try, or even if I'm at a salvageable point. here's a screenshot of GParted: This makes me suspicious that it wasn't necessarily the removal of my HP_TOOLS partition but the "unknown" status of that 992.50 KiB partition there, sda1. I'm assuming that's the recovery one? How can I get Windows bootable again? I'm sorry, but I'm so unfamiliar with this sort of thing I'm not quite sure where to start.

    Read the article

  • Need software to convert RAR to ZIP ("store" mode - no compression) * Extract->re-archive changes date/time attributes

    - by Larry78
    I have tried all of the following applications (download.cnet.com - the free ones), and none of them will convert an RAR archive to a ZIP, without compressing the files ("store" mode). 7-ZIP would be fine, too. [The RAR is a "solid" archive with password (I know it), files "stored" - no compression, used WinRAR 3.5.1] PeaZip, 7-Zip, FilZip, TugZip, SimplyZipSE, QuickZip, WinShrink. (A couple of the apps let you try, but the program gives an error - indicating how bad the software is. (Like "unknown header # #.") None of these apps will do the conversion at all. IZArc 4.1 comes the closest. It will convert an RAR to a ZIP, but it compresses the zip. There is a general preference setting to "store" - but it doesn't effect conversions. I don't want to extract the RAR files and re-archive them because I need to preserve the modified/created file attributes. IZArc preserves them, but it compresses the files. WinRAR has the option to convert archives, but I get the error "skipping encryped archive" when I try to convert it. It asks for the password first, and I know it's right because that password opens the archive, and I can read/view all the files in the archive.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • HP LaserJet 1515: Disable "refill" warning

    - by Pekka
    I have a HP LaserJet 1515 connected to a Windows 7 PC. The Magenta cartridge is empty; the printer shows a warning to that effect, and won't let me print even black-and-white documents any more. I can't turn the warning off manually using the printer's small console: When I try to enter any menu, the display says "Menu access disabled". I have no idea why. There is a setting to override the warning, but it can't be changed using the Network interface in the browser (Although it is there on the status page) According to the manual,the HP printing tool is supposed to offer a switch for this, but it won't install on my Windows 7. It just rumbles about for half an hour, to magnificently exit with an "unknown error" requiring a reboot. On second look, the problem seems to be that Windows 7 just isn't supported. There is no download link for the tool when you specify Windows 7 as your OS. I just want to print a black-and-white-document on a printer whose black cartridge is still 65% full. Is this indeed impossible? On second thought, I'm cross-posting this on the HP support forum. I'll update here if anything comes up.

    Read the article

  • Computer is dying--what should I be looking for?

    - by Will
    Okay, I'm a bit knowledgeable with pooters and such, but i'm confused. My computer is dying slowly, and I'm not sure what part is causing this. Computer details: Vista, dell machine, intel Q6600, 2.4 Core Duo (quad core), standard memory and drive (unknown manufacturer). Symptoms: I would best describe the symptoms as memory corruption. After a couple days on, I start getting applications crashing or failing to open for a lack of "resources". Sounds are corrupted. Onscreen text gets corrupted; the characters of text are garbled, not the pixels on the screen. Video memory seems untouched as I haven't seen any misplaced pixels. Recently I've lost files on disk. I've also experienced errors reporting a supposed lack of disk space, even though I have fifty gigs free. There was one point where I couldn't get to the POST when booting up. After I cleaned everything (see next) this hasn't happened. Diagnostic steps: First thing I did was clean the case. There was a lot of dust buildup on heatsinks, so I cleaned all that up. No help. Next, I disconnected and reconnected everything, from power cables to memory (did not reseat cpu). No change. Last, I ran the standard vista memory diagnostics and ran checkdisk. Both reported no errors found. I have not run any POST tests, now that I think about it. I'm at a loss at this point. Disk appears fine, memory too. I'd expect motherboard issues to result in the thing not booting up, yet it does every time. What should I be looking at? What more can I do?

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • how to recover my xml default icon?

    - by moonway
    My XML files are showing the unknown programs icon, you can see in this picture: i cant revise its icon why? i look it up in the registry i find no error look at the following Windows Registry Editor Version 5.00 [HKEY_CLASSES_ROOT.xml] @="xmlfile" "Content Type"="text/xml" "PerceivedType"="text" [HKEY_CLASSES_ROOT.xml\PersistentHandler] @="{7E9D8D44-6926-426F-AA2B-217A819A5CCE}" Windows Registry Editor Version 5.00 [HKEY_CLASSES_ROOT\xmlfile] @="@C:\Windows\System32\msxml3r.dll,-1" "EditFlags"=hex:00,00,00,00 "FriendlyTypeName"=hex(2):40,00,25,00,53,00,79,00,73,00,74,00,65,00,6d,00,52,\ 00,6f,00,6f,00,74,00,25,00,5c,00,53,00,79,00,73,00,74,00,65,00,6d,00,33,00,\ 32,00,5c,00,6d,00,73,00,78,00,6d,00,6c,00,33,00,72,00,2e,00,64,00,6c,00,6c,\ 00,2c,00,2d,00,31,00,00,00 [HKEY_CLASSES_ROOT\xmlfile\BrowseInPlace] [HKEY_CLASSES_ROOT\xmlfile\CLSID] @="{48123BC4-99D9-11D1-A6B3-00C04FD91555}" [HKEY_CLASSES_ROOT\xmlfile\DefaultIcon] @="C:\Windows\System32\msxml3.dll,0" [HKEY_CLASSES_ROOT\xmlfile\shell] @="open" [HKEY_CLASSES_ROOT\xmlfile\shell\edit] [HKEY_CLASSES_ROOT\xmlfile\shell\edit\command] @="\"C:\Program Files\Common Files\Microsoft Shared\OFFICE11\MSOXMLED.EXE\" /verb edit \"%1\"" [HKEY_CLASSES_ROOT\xmlfile\shell\Open] [HKEY_CLASSES_ROOT\xmlfile\shell\Open\Command] @="\"C:\Program Files\Common Files\Microsoft Shared\OFFICE11\MSOXMLED.EXE\" /verb open \"%1\"" [HKEY_CLASSES_ROOT\xmlfile\shell\Open\ddeexec] @="" [HKEY_CLASSES_ROOT\xmlfile\ShellEx] [HKEY_CLASSES_ROOT\xmlfile\ShellEx\IconHandler] @="{AB968F1E-E20B-403A-9EB8-72EB0EB6797E}" can you find something wrong or you can paste your reg hehe i need default reg about xml which is with default associated exe all right!

    Read the article

  • Mercurial fails while commiting/updating/etc. using Mercuriual+TrueCrypt+MAC

    - by lukewar
    While trying to work with Mercurial on project located on TrueCrypt partition I always get en error as follows: ** unknown exception encountered, details follow ** report bug details to http://mercurial.selenic.com/bts/ ** or [email protected] ** Mercurial Distributed SCM (version 1.5.2+20100502) ** Extensions loaded: Traceback (most recent call last): File "/usr/local/bin/hg", line 27, in mercurial.dispatch.run() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 16, in run sys.exit(dispatch(sys.argv[1:])) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 30, in dispatch return _runcatch(u, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 50, in _runcatch return _dispatch(ui, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 470, in _dispatch return runcommand(lui, repo, cmd, fullargs, ui, options, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 340, in runcommand ret = _runcommand(ui, options, cmd, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 521, in _runcommand return checkargs() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 475, in checkargs return cmdfunc() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 469, in d = lambda: util.checksignature(func)(ui, *args, **cmdoptions) File "/Library/Python/2.6/site-packages/mercurial/util.py", line 401, in check return func(*args, **kwargs) File "/Library/Python/2.6/site-packages/mercurial/commands.py", line 3332, in update return hg.update(repo, rev) File "/Library/Python/2.6/site-packages/mercurial/hg.py", line 362, in update stats = _merge.update(repo, node, False, False, None) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 495, in update _checkunknown(wc, p2) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 77, in _checkunknown for f in wctx.unknown(): File "/Library/Python/2.6/site-packages/mercurial/context.py", line 660, in unknown return self._status[4] File "/Library/Python/2.6/site-packages/mercurial/util.py", line 156, in get result = self.func(obj) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 622, in _status return self._repo.status(unknown=True) File "/Library/Python/2.6/site-packages/mercurial/localrepo.py", line 1023, in status if (f not in ctx1 or ctx2.flags(f) != ctx1.flags(f) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 694, in flags flag = findflag(self._parents[0]) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 690, in findflag return ff(path) File "/Library/Python/2.6/site-packages/mercurial/dirstate.py", line 145, in f if 'x' in fallback(x): TypeError: argument of type 'NoneType' is not iterable It is worth mention that Mercurial works perfectly if project is not located on TrueCrypt partition. Configuration: MacOS X 10.6.3 Mercurial Distributed SCM (version 1.5.2+20100502) Python 2.6.5 Have anyone of you generous people able to help me? :)

    Read the article

  • AD - Using UserPrincipal.FindByIdentity and PrincipalContext with nested OU - C#

    - by Solid Snake
    Here is what I am trying to achieve: I have a nested OU structure that is about 5 levels deep. OU=Portal,OU=Dev,OU=Apps,OU=Grps,OU=Admin,DC=test,DC=com I am trying to find out if the user has permissions/exists at OU=Portal. Here's a snippet of what I currently have: PrincipalContext domain = new PrincipalContext( ContextType.Domain, "test.com", "OU=Portal,OU=Dev,OU=Apps,OU=Grps,OU=Admin,DC=test,DC=com"); UserPrincipal user = UserPrincipal.FindByIdentity(domain, myusername); PrincipalSearchResult<Principal> group = user.GetAuthorizationGroups(); For some unknown reason, the value user generated from the above code is always null. However, if I were to drop all the OU as follows: PrincipalContext domain = new PrincipalContext( ContextType.Domain, "test.com", "DC=test,DC=com"); UserPrincipal user = UserPrincipal.FindByIdentity(domain, myusername); PrincipalSearchResult<Principal> group = user.GetAuthorizationGroups(); this would work just fine and return me the correct user. I am simply trying to reduce the number of results as opposed to getting everything from AD. Is there anything that I am doing wrong? I've googled for hours and tested various combinations without much luck. Any help is appreciated. Thanks. Dan

    Read the article

  • Linq to SQL EntitySet Binding the MVVM way

    - by Savvas Sopiadis
    Hi everybody! In a WPF application i'm using LINQ to SQL classes (created by SQL Metal, thus implementing POCOs). Let's assume i have a table User and a Table Pictures. These pictures are actually created from one picture, the difference between them may be the size, coloring,... So every user may has more than one Pictures, so the association is 1:N (User:Pictures). My problems: a) how do i bind, in a MVVM manner, a picture control to one picture (i will take one specific picture) in the EntitySet, to show it up? b) everytime a user changes her picture the whole EntitySet should be thrown away and the newly created Picture(s) should be a added. Is this the correct way? e.g. //create the 1st piture object UserPicture1 = new UserPicture(); UserPicture1.Description = "... some description.. "; USerPicture1.Image = imgBytes; //array of bytes //create the 2nd piture object UserPicture2 = new UserPicture(); UserPicture2.Description = "... another description.. "; UserPicture2.Image = DoSomethingWithPreviousImg(imgBytes); //array of bytes //Assuming that the entityset is called Pictures //add these pictures to the corresponding user User.Pictures.Add(UserPicture1); User.Pictures.Add(UserPicture2); //save changes datacontext.Save() Thanks in advance

    Read the article

  • How to connect to SQL Server using activerecord, JDBC, JTDS and Integrated Security

    - by Rob
    As per the above, I've tried: establish_connection(:adapter => "jdbcmssql", :url => "jdbc:jtds:sqlserver://myserver:1433/mydatabase;domain='mynetwork';", :username => 'user', :password=>'pass' ) establish_connection(:adapter => "jdbcmssql", :url => 'jdbc:jtds:sqlserver://myserver:1433/mydatabase;domain="mynetwork";user="mynetwork\user"' ) establish_connection(:adapter => "jdbcmssql", :url => "jdbc:jtds:sqlserver://myserver:1433/mydatabase;domain='mynetwork';", :username=>'user' ) establish_connection(:adapter => "jdbcmssql", :url => "jdbc:jtds:sqlserver://myserver:1433/mydatabase;domain='mynetwork';integratedSecurity='true'", :username=>'user' ) .. and various other combinations. Each time I get: net/sourceforge/jtds/jdbc/SQLDiagnostic.java:368:in `addDiagnostic': java.sql.SQLException: Login failed for user ''. The user is not associated with a trusted SQL Server connection. (NativeException) Any tips? Thanks, activerecord (2.3.5) activerecord-jdbc-adapter (0.9.6) activerecord-jdbcmssql-adapter (0.9.6) jdbc-jtds (1.2.5) jruby 1.4.0 (ruby 1.8.7 patchlevel 174) (2009-11-02 69fbfa3) (Java HotSpot(TM) Client VM 1.6.0_18) [x86-java]

    Read the article

  • SSRS 2008: is it possible to make a report parameter NOT query-based for some linked report?

    - by Stefan Mohr
    I suspect the answer is no, but here goes.. I'm using the WebForms Report Viewer on a public-facing website to allow users to report on themselves or their users (if the user is an admin user). A report has a parameter called Users where an admin can pick a user from the list and generate a report from it. Mundane users can also view this report, but I programmatically create a linked report for each user and set the UserID value to their ID so they can only view themselves. This works well except that the UserID parameter is query-based, and not every user is visible in the list using default settings (the user list is based off date range parameters can provide, and only users we consider 'active' during the date range are visible). This is blowing up for mundane users that are not active for the default date range (which is the previous month). I suspect the flow of execution is something like this: Report loads with default parameters The linked report rules are now applied and the value of the UserID is overridden with the ID in the linked report UserID field is now hidden to prevent the user from changing it SSRS can't find the UserID default value in the query results (that I didn't even want it to run) so it displays an error The 'UserID' parameter is missing a value Through some testing I've found a perfect correlation between users not inside the default date range and users who can't view the report. Can anyone suggest a way to make the report usable for those users that aren't in the default list? The reports are created programmatically so I do have a fair bit of control over the situation. I would love to simply be able to mark a parameter in a linked report as no longer being query-based, but those properties are all read-only. I really, really don't want to have to create duplicate reports to accommodate these users but I'm at a bit of a loss right now. Any suggestions are greatly appreciated!

    Read the article

  • Using JBoss EL with Websphere

    - by rat
    Hey, I'm doing a project which is going to run on Websphere. I'm using JSF/Facelets/Richfaces for this project. I want to use the JBoss EL implementation as it allows calling methods with parameters from EL etc. ... usually this is accomplished by getting the JBoss EL jar and then putting this in the web.xml: <context-param> <param-name>com.sun.faces.expressionFactory</param-name> <param-value>org.jboss.el.ExpressionFactoryImpl</param-value> </context-param> However this isn't working ... I don't know if its a problem with Websphere or ...??? I get a stack trace when going to the page saying it can't parse the EL where I have passed a method a parameter: <a4j:commandLink value="Delete" action="#{mcsaAdmin.deleteLanguage(1234)}" /> Looking at the stacktrace it appears to still be using the standard sun EL: Caused by: javax.el.ELException: Error Parsing: #{mcsaAdmin.deleteLanguage(1234)} at com.sun.el.lang.ExpressionBuilder.createNodeInternal(Unknown Source) at com.sun.el.lang.ExpressionBuilder.build(Unknown Source) at com.sun.el.lang.ExpressionBuilder.createMethodExpression(Unknown Source) at com.sun.el.ExpressionFactoryImpl.createMethodExpression(Unknown Source) at com.sun.facelets.tag.TagAttribute.getMethodExpression(TagAttribute.java:141) Note the 'com.sun.el.ExpressionFactoryImpl' instead of 'org.jboss.el.ExpressionFactoryImpl' as specified above ... Am I doing something obviously wrong? Anyone have any ideas... I'm using standard JSF implementation from majorra project or whatever provided on sun website and richfaces 3.1.4 and facelets 1.1.14.

    Read the article

< Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >