Search Results

Search found 20163 results on 807 pages for 'struct size'.

Page 410/807 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• Rosegarden don't work

  - by Brallan Aguilar

  I recently installed Rosegarden. When it had ran for the first time, it worked excellent. After, I had to restart my computer and when I ran it for the second time, something strange was occurred: according to the System Monitor, Rosegarden was running, in spite of I couldn't see the application, sometimes it's opened at other desktop and also Unity always has some instability problems like disappear the title bar of other programs or a zone is marked (for example, when we drag a window to the right side, we can see an "orange" area and the window's size is reduced to distribute at the middle of the desktop) at the left side of the screen and isn't hidden.

  Read the article

• How can you print a text file via gedit from the command line?

  - by dan

  I'd like to use gedit or some similar program just as a page formatter and pipe some text through it and onto the printer. | lpr just doesn't cut it in the presentation department. The printed output is subpar, even if I try to tinker with the margin and font size options. But I like the way text looks like when printed from gedit. Is there a way to have the best of both worlds and use a command line pipeline to print a text file with gedit-quality formatting?

  Read the article

• Is it a bad practice to store large files (10 MB) in a database?

  - by B Seven

  I am currently creating a web application that allows users to store and share files, 1 MB - 10 MB in size. It seems to me that storing the files in a database will significantly slow down database access. Is this a valid concern? Is it better to store the files in the file system and save the file name and path in the database? Are there any best practices related to storing files when working with a database? I am working in PHP and MySQL for this project, but is the issue the same for most environments (Ruby on Rails, PHP, .NET) and databases (MySQL, PostgreSQL).

  Read the article

• MySQL vs. SQL Server Go daddy, What is the difference bewteen hosted DB and App_Data Db

  - by Nate Gates

  I'm using Goddady for site hosting, and I'm currently using MySQL, because there are less limits on size,etc. My question is what is the difference between using a hosted Godaddy Db such as MySQL vs. creating a SQL Serverdatabase in the the App_Data folder? My guess is security? Would it be a bad idea to use a SQL ServerDB thats located in the App_Data folder? Additional Well I am able to create a .mdf (SQL Server DB file) in the App_Data folder, but I'm really unsure if should use that or not, If I did use it it would simplify using some of the Microsoft tools. Like I said my guess is that it would be less secure, but I don't really know. I know I have a 10gb, file system limit, so I'm assuming my db would have to share that space.

  Read the article

• 1st Issue of GIMP Magazine now Available [Free Download]

  - by Asian Angel

  Are you ready for an awesome (and free) magazine that is all about GIMP? Then GIMP Magazine is the publication that you have been looking for! This free quarterly magazine focuses on photography, digital arts, tips and tricks, step by step tutorials, master classes, help desk questions, and so much more. You can access the 1st issue in three ways: As a direct PDF download As a Bit-Torrent download View it online at Issuu Choose the option that works best for you! Note: The PDF file is 47.1 MB in size. A sample page from the magazine for your viewing pleasure… HTG Explains: Is ReadyBoost Worth Using? HTG Explains: What The Windows Event Viewer Is and How You Can Use It HTG Explains: How Windows Uses The Task Scheduler for System Tasks

  Read the article

• Shows how to use AutocompleteExtender to populate subjects and databind quotations via Entity Framew

  This article will focus on a database of famous quotations that I"ve pared down to a downloadable size for a demo, and how to wire up the AJAX Toolkit autocomplete extender to a textbox that is used to typeahead a Subject. When the ClientItemSelected event fires, the Display button Click is invoked, and this causes an EF query to display the matching quotes in a DataList.  read moreBy Peter BrombergDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Shows how to use AutocompleteExtender to populate subjects and databind quotations via Entity Framew

  This article will focus on a database of famous quotations that I"ve pared down to a downloadable size for a demo, and how to wire up the AJAX Toolkit autocomplete extender to a textbox that is used to typeahead a Subject. When the ClientItemSelected event fires, the Display button Click is invoked, and this causes an EF query to display the matching quotes in a DataList.  read moreBy Peter BrombergDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Backup files with rsync: error 23

  - by maria

  Hi I'm trying to make a backup of my /home to transfer all data from one computer to another. I wanted to save the backup on the same computer and than transfere it to another one. For safety reasons, I'm trying to learn how does it work on the computer without a lot of data (the new one) to be sure I won't delete something instead of copying it. I've run in terminal: sudo rsync -avz /home/maria /home/guest/backup and I had as the result: sent 58797801 bytes received 23050 bytes 4705668.08 bytes/sec total size is 100202958 speedup is 1.70 rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1060) [sender=3.0.7] I've tried once again, with the same result. I have no idea, which files were not transferred, what makes the whole backup useless for me (I wanted to do it automatically in order not to forget about something and loose it). On both computers I have the same system (Ubuntu 10.04). Rsync version: 3.0.7-1ubuntu1. Thanks for any tips

  Read the article

• Example: Controlling randomizer using code contracts

  - by DigiMortal

  One cool addition to Visual Studio 2010 is support for code contracts. Code contracts make sure that all conditions under what method is supposed to run correctly are met. Those who are familiar with unit tests will find code contracts easy to use. In this posting I will show you simple example about static contract checking (example solution is included). To try out code contracts you need at least Visual Studio 2010 Standard Edition. Also you need code contracts package. You can download package from DevLabs Code Contracts page. NB! Speakers, you can use the example solution in your presentations as long as you mention me and this blog in your sessions. Solution has readme.txt file that gives you steps to go through when presenting solution in sessions. This blog posting is companion posting for Visual Studio solution referred below. As an example let’s look at the following class. public class Randomizer {     public static int GetRandomFromRange(int min, int max)     {         var rnd = new Random();         return rnd.Next(min, max);     }       public static int GetRandomFromRangeContracted(int min, int max)     {         Contract.Requires(min < max, "Min must be less than max");           var rnd = new Random();         return rnd.Next(min, max);     } } GetRandomFromRange() method returns results without any checking. GetRandomFromRangeContracted() uses one code contract that makes sure that minimum value is less than maximum value. Now let’s run the following code. class Program {     static void Main(string[] args)     {         var random1 = Randomizer.GetRandomFromRange(0, 9);         Console.WriteLine("Random 1: " + random1);           var random2 = Randomizer.GetRandomFromRange(1, 1);         Console.WriteLine("Random 2: " + random2);           var random3 = Randomizer.GetRandomFromRangeContracted(5, 5);         Console.WriteLine("Random 3: " + random3);           Console.WriteLine(" ");         Console.WriteLine("Press any key to exit ...");         Console.ReadKey();     } } As we have not turned on support for code contracts the code runs without any problems and we get no warnings by Visual Studio that something is wrong. Now let’s turn on static checking for code contracts. As you can see then code still compiles without any errors but Visual Studio warns you about possible problems with contracts. Click on image to see it at original size.  When we open Error list and run our application we get the following output to errors list. Note that these messages are not shown immediately. There is little delay between application starting and appearance of these messages. So wait couple of seconds before going out of your mind. Click on image to see it at original size.  If you look at these warnings you can see that warnings show you illegal calls and also contracts against what they are going. Third warning points to GetRandomFromRange() method and shows that there should be also problem that can be detected by contract. Download Code Contracts example VS2010 solution | 30KB

  Read the article

• Cant access ephemeral storage on Amazon ubuntu instance

  - by matt burns

  I want to utilise my ephemeral storage as mentioned in this question but I seem to be falling at the first hurdle. I can't even see /mnt: ~$ df -ah Filesystem Size Used Avail Use% Mounted on /dev/xvda1 8.0G 855M 6.8G 12% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 288M 8.0K 288M 1% /dev devpts 0 0 0 - /dev/pts tmpfs 119M 152K 118M 1% /run none 5.0M 0 5.0M 0% /run/lock none 296M 0 296M 0% /run/shm This is from a vanilla instance of an ubuntu AMI (12.04-amd64-server-20120424 ami-a29943cb) I'm not bothered about resizing the partition, I just want to be able to use the space for writing temp files.

  Read the article

• Games with multiple flash files not working

  - by zlyfire

  I have download a flash game, since that's show the person coded it, and it is in multiple flash files to reduce overall file size or something. When I try to play it, I can only use the content within that one flash file, leading me to believe that it does not call upon other files within my computer. I kept the same file structure and everything as the download was, and another version of the same game I had on my windows laptop before my laptop died. It worked fine there, calling the files like it was supposed to. Is it just an Ubuntu/Linux/Unix-based bug, or is something going wrong? I've tried it in browser (firefox) and offline (gnash) and neither worked properly. Can anyone help me with this? Perhaps helping me find a way to get my game to work properly?

  Read the article

• Where did my free space go?

  - by Ari B. Friedman

  I have a storage drive (2TB) and an OS drive (90GB SSD). I've run out of space on the OS drive: /$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sdb1 72G 72G 0 100% / udev 5.9G 12K 5.9G 1% /dev tmpfs 2.4G 1.2M 2.4G 1% /run none 5.0M 0 5.0M 0% /run/lock none 5.9G 428K 5.9G 1% /run/shm /dev/sda1 1.9T 639G 1.2T 37% /media/StorageDrive So be it. But when I attempt to figure out where the space has gone, I cannot find it anything remotely approaching the capacity of the drive: /$ sudo du -h -d 1 du: cannot access `./media/StorageDrive/home/ari/.gvfs': Permission denied 675G ./media 2.3G ./var 0 ./proc 7.0M ./tmp 27M ./boot 4.0K ./lib64 12K ./dev 44M ./home 16K ./lost+found 8.0M ./sbin 223M ./lib 4.0K ./selinux 1.4M ./run 140K ./root 8.8M ./bin 4.0K ./mnt 38M ./etc 8.0K ./srv 4.8G ./usr 65M ./opt 0 ./sys 682G . Note the difference between the total (682G) and the mounted drives in /media (675G) is only about 9G. How are 72G being used? Where is this dark matter hiding?

  Read the article

• /boot partition is NTFS on dual-boot Win7/Ubuntu 12.04 Desktop

  - by efreem01

  I recently purchased an Acer Aspire laptop. Windows 7 Home Premium edition was installed on the main drive. I booted to the Ubuntu 12.04 Installation environment and selected the option to Install Ubuntu alonside Windows 7. I now have two data partitions roughly half the size of the HD (NTFS and EXT4) and a /boot partition that is NTFS. How can i convert the /boot partition to EXT without breaking Ubuntu and Windows 7? I would like to tri-boot it with another Environment if possible, but this is presenting a problem.

  Read the article

• Ubuntu 12.04.3 alongside Windows 8.1

  - by user208329

  I brought a new Notebook which has pre-installed Windows 8.1 with an uefi* (-Bios) and secure boot*. (* can switch or turn so off, still no success) When i try to install Ubuntu 12.04.3, the installer doesn't recognize Windows 8.1. There were options, to delete the whole disk or do something else. The second option, shows a few partitions (NTFS) but no Windows. The Ubuntu 13.10 version even did start on my notebook, it gets frozen during start up. (I thought. maybe the newer one will recognize Windows.) I'm not very confident in manipulating grub, I hope there is an easy way or an easy description. Gparted shows: Device Type Size Used /dev/sda freespace 1MB /dev/sda ntfs 1073MB 408MB /dev/sda2 efi 104MB 52MB /dev/sda3 ntfs 134MB 45MB /dev/sda4 ntfs 988465MB 23947MB /dev/sda5 ntfs 10424MB 9483MB free space 0MB /dev/sdb1 fat32 16929MB 9412MB (USB-drive Ubuntu-image)

  Read the article

• How To Specify Bitrate, Codec and Demultiplexing for VLC Video Capture or Recording

  - by Subhash

  I capture video from old TV tuner card - Pinnacle PCTV - using VLC. The video is from the Composite input and audio is from I guess the mixer or Line in. The command I use is: vlc v4l2:///dev/video0:normal=pal:width=720:height=576:input=1 :input-slave="alsa://hw:0,0" In VLC, I have enabled the Advanced Controls toolbar, which allows me to record videos when I want to. However, these videos are uncompressed - very big and play only with VLC. Totem throws the "Could not demultiplex stream" error. I need to convert them using WinFF to reduce their size and make them playable with Totem and other software. My question is whether I can configure the recording settings - the codecs and the bitrate, and also get the stream demultiplexed. If I pass any -sout parameter with command I get a "Segmentation fault". I use 64-bit Ubuntu 10.10.

  Read the article

• So long wizards!

  - by geekrutherford

  In an effort to make an application more robust I have been switching to a server-side method of tracking record selections vs. client side.   The pages relying on record selections utilized the ASP.NET Wizard control which seemed like a good idea originally. Unfortunately, the design of the control is not all that flexible. It appears to want to center everything vertically which might not be a problem if it did not always use the vertical size of the largest Wizard Step for positioning.   So, I am ripping out the Wizard controls and replacing with simple Panel controls that are turned on/off. Much cleaner and presentable.

  Read the article

• 3d vertex translated onto 2d viewport

  - by Dan Leidal

  I have a spherical world defined by simple trigonometric functions to create triangles that are relatively similar in size and shape throughout. What I want to be able to do is use mouse input to target a range of vertices in the area around the mouse click in order to manipulate these vertices in real time. I read a post on this forum regarding translating 3d world coordinates into the 2d viewport.. it recommended that you should multiply the world vector coordinates by the viewport and then the projection, but they didn't include any code examples, and suffice to say i couldn't get any good results. Further information.. I am using a lookat method for the viewport. Does this cause a problem, and if so is there a solution? If this isn't the problem, does anyone have a simple code example illustrating translating one vertex in a 3d world into a 2d viewspace? I am using XNA.

  Read the article

• How a "Collision System" should be implemented?

  - by nathan

  My game is written using a entity system approach using Artemis Framework. Right know my collision detection is called from the Movement System but i'm wondering if it's a proper way to do collision detection using such an approach. Right know i'm thinking of a new system dedicated to collision detection that would proceed all the solid entities to check if they are in collision with another one. I'm wondering if it's a correct way to handle collision detection with an entity system approach? Also, how should i implement this collision system? I though of an IntervalEntitySystem that would check every 200ms (this value is chosen regarding the Artemis documentation) if some entities are colliding. protected void processEntities(ImmutableBag<Entity> ib) { for (int i = 0; i < ib.size(); i++) { Entity e = ib.get(i); //check of collision with other entities here } }

  Read the article

• Simple iOS glDrawElements - BAD_ACCESS

  - by user699215

  You can copy paste this into the default OpenGl template created in Xcode. Why am I not seeing anything :-) It is strange as the glDrawArrays(GL_TRIANGLES, 0, 3); is working fine, but with glDrawElements(GL_TRIANGLE_STRIP, sizeof(indices)/sizeof(GLubyte), GL_UNSIGNED_BYTE, indices); Is giving BAD_ACCESS? Copy paste this into Xcode default OpenGl template: ViewController #import "ViewController.h" #define BUFFER_OFFSET(i) ((char *)NULL + (i)) // Uniform index. enum { UNIFORM_MODELVIEWPROJECTION_MATRIX, UNIFORM_NORMAL_MATRIX, NUM_UNIFORMS }; GLint uniforms[NUM_UNIFORMS]; // Attribute index. enum { ATTRIB_VERTEX, ATTRIB_NORMAL, NUM_ATTRIBUTES }; @interface ViewController () { GLKMatrix4 _modelViewProjectionMatrix; GLKMatrix3 _normalMatrix; float _rotation; GLuint _vertexArray; GLuint _vertexBuffer; NSArray* arrayOfVertex; } @property (strong, nonatomic) EAGLContext *context; @property (strong, nonatomic) GLKBaseEffect *effect; - (void)setupGL; - (void)tearDownGL; @end @implementation ViewController - (void)viewDidLoad { [super viewDidLoad]; self.context = [[EAGLContext alloc] initWithAPI:kEAGLRenderingAPIOpenGLES2]; GLKView *view = (GLKView *)self.view; view.context = self.context; view.drawableDepthFormat = GLKViewDrawableDepthFormat24; [self setupGL]; } - (void)dealloc { [self tearDownGL]; if ([EAGLContext currentContext] == self.context) { [EAGLContext setCurrentContext:nil]; } } - (void)didReceiveMemoryWarning { [super didReceiveMemoryWarning]; if ([self isViewLoaded] && ([[self view] window] == nil)) { self.view = nil; [self tearDownGL]; if ([EAGLContext currentContext] == self.context) { [EAGLContext setCurrentContext:nil]; } self.context = nil; } // Dispose of any resources that can be recreated. } GLuint vertexBufferID; GLuint indexBufferID; static const GLfloat vertices[9] = { -0.5, -0.5, 0.5, 0.5, -0.5, 0.5, -0.5, 0.5, 0.5 }; static const GLubyte indices[3] = { 0, 1, 2 }; - (void)setupGL { [EAGLContext setCurrentContext:self.context]; // [self loadShaders]; self.effect = [[GLKBaseEffect alloc] init]; self.effect.light0.enabled = GL_TRUE; self.effect.light0.diffuseColor = GLKVector4Make(1.0f, 0.4f, 0.4f, 1.0f); glEnable(GL_DEPTH_TEST); // glGenVertexArraysOES(1, &_vertexArray); // glBindVertexArrayOES(_vertexArray); glGenBuffers(1, &vertexBufferID); glBindBuffer(GL_ARRAY_BUFFER, vertexBufferID); glBufferData(GL_ARRAY_BUFFER, sizeof(vertices), vertices, GL_STATIC_DRAW); glGenBuffers(1, &indexBufferID); glBindBuffer(GL_ELEMENT_ARRAY_BUFFER, indexBufferID); glBufferData(GL_ELEMENT_ARRAY_BUFFER, sizeof(indices), indices, GL_STATIC_DRAW); glEnableVertexAttribArray(GLKVertexAttribPosition); glVertexAttribPointer(GLKVertexAttribPosition, // Specifies the index of the generic vertex attribute to be modified. 3, // Specifies the number of components per generic vertex attribute. Must be 1, 2, 3, 4. GL_FLOAT, // GL_FALSE, // 0, // BUFFER_OFFSET(0)); // // glBindVertexArrayOES(0); } - (void)tearDownGL { [EAGLContext setCurrentContext:self.context]; glDeleteBuffers(1, &_vertexBuffer); glDeleteVertexArraysOES(1, &_vertexArray); self.effect = nil; } #pragma mark - GLKView and GLKViewController delegate methods - (void)update { float aspect = fabsf(self.view.bounds.size.width / self.view.bounds.size.height); GLKMatrix4 projectionMatrix = GLKMatrix4MakePerspective(GLKMathDegreesToRadians(65.0f), aspect, 0.1f, 100.0f); self.effect.transform.projectionMatrix = projectionMatrix; GLKMatrix4 baseModelViewMatrix = GLKMatrix4MakeTranslation(0.0f, 0.0f, -4.0f); baseModelViewMatrix = GLKMatrix4Rotate(baseModelViewMatrix, _rotation, 0.0f, 1.0f, 0.0f); // Compute the model view matrix for the object rendered with GLKit GLKMatrix4 modelViewMatrix = GLKMatrix4MakeTranslation(0.0f, 0.0f, -1.5f); modelViewMatrix = GLKMatrix4Rotate(modelViewMatrix, _rotation, 1.0f, 1.0f, 1.0f); modelViewMatrix = GLKMatrix4Multiply(baseModelViewMatrix, modelViewMatrix); self.effect.transform.modelviewMatrix = modelViewMatrix; // Compute the model view matrix for the object rendered with ES2 modelViewMatrix = GLKMatrix4MakeTranslation(0.0f, 0.0f, 1.5f); modelViewMatrix = GLKMatrix4Rotate(modelViewMatrix, _rotation, 1.0f, 1.0f, 1.0f); modelViewMatrix = GLKMatrix4Multiply(baseModelViewMatrix, modelViewMatrix); _normalMatrix = GLKMatrix3InvertAndTranspose(GLKMatrix4GetMatrix3(modelViewMatrix), NULL); _modelViewProjectionMatrix = GLKMatrix4Multiply(projectionMatrix, modelViewMatrix); _rotation += self.timeSinceLastUpdate * 0.5f; } int i; - (void)glkView:(GLKView *)view drawInRect:(CGRect)rect { glClearColor(0.65f, 0.65f, 0.65f, 1.0f); glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); // glBindVertexArrayOES(_vertexArray); // Render the object with GLKit [self.effect prepareToDraw]; //glDrawArrays(GL_TRIANGLES, 0, 3); // Render the object again with ES2 // glDrawArrays(GL_TRIANGLES, 0, 3); glDrawElements(GL_TRIANGLE_STRIP, sizeof(indices)/sizeof(GLubyte), GL_UNSIGNED_BYTE, indices); } @end

  Read the article

• Making a game "resize-safe"

  - by CPP_Person

  It's one thing to get the graphics aligned perfectly, it's another to do this for every single resolution and not take too much time and/or make the code unreadable due to size. Games like Battlefield 3 and Minecraft seem to manage this. But what do they do to keep things from stretching or going off the screen? I don't know any algorithms to do this. I'd like some help on this topic. I've always programmed games that only handle a single resolution, so help would be appreciate.

  Read the article

• Upgrading from raring to saucy broke many of my fonts in certain applications

  - by valadil

  I upgraded from raring to saucy over the weekend. Two of my applications, dzen2 and xmobar, won't display the fonts they used to. I'd mostly been using fixed and 6x12. xmobar doesn't run with these fonts. dzen2 shows some generic font I can't identify. I can change the size but not the font. The only exception is terminus. I looped over xlsfonts and piped them into a dzen2 to see what still worked. Variants of terminus were fine. Everything else used the same generic looking font face. No idea why. I haven't found any other applications with font issues since the update, but I haven't tried too hard to look either.

  Read the article

• Is "no installation" software a good thing?

  - by Yaron Naveh

  I am building an application that will, hopefully, be used by developers. To be appealing to developers I want it to be lightweight, small in size, and with no installation (e.g. xcopy). I trust more an application without installation to not put garbage in my registry, to be lightweight etc. My friend thinks the opposite: An installer puts shortcuts on the desktop / menu for me, it ensures cleanup via the uninstaller, and seems more official. I'm curious - what is everyone's take on this?

  Read the article

• How do I programatically determine which port a SQL Server is running on?

  - by Ralph Willgoss

  How do I programatically determine which port a SQL Server is running on?/*Wrapper script for xp_readerrorlogAuthor: Ralph WillgossDate: 2nd Oct 2012This script cycles through all logs files, looking for the listening port.Normally you have to specify the log file one by one, the script removes the need for that.Param ref for: xp_readerrorlog1. Value of error log file you want to read: 0 = current, 1 = Archive #1, 2 = Archive #2, etc...2. Log file type: 1 or NULL = error log, 2 = SQL Agent log3. Search string 1: String one you want to search for4. Search string 2: String two you want to search for to further refine the results5. Search from start time6. Search to end time7. Sort order for results: N'asc' = ascending, N'desc' = descending*/USE MasterGO--  Get log countDECLARE @logcount intDROP TABLE #ResultCREATE TABLE #Result (ArchiveNo int, Date datetime, Size int)INSERT INTO #ResultEXEC xp_enumerrorlogsSET @logcount = (SELECT COUNT(*) FROM #Result)-- Search the available logsDECLARE @counter intSET @counter = 0WHILE @counter <= @logcountBEGIN   EXEC xp_readerrorlog @counter, 1, N'Server is listening on', 'any', NULL, NULL, N'asc'   SET @counter = @counter + 1ENDGO

  Read the article

• OpenGL: Filtering/antialising textures in a 2D game

  - by futlib

  I'm working on a 2D game using OpenGL 1.5 that uses rather large textures. I'm seeing aliasing effects and am wondering how to tackle those. I'm finding lots of material about antialiasing in 3D games, but I don't see how most of that applies to 2D games - e.g. antisoptric filtering seems to make no sense, FSAA doesn't sound like the best bet either. I suppose this means texture filtering is my best option? Right now I'm using bilinear filtering, I think: glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_LINEAR); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_LINEAR); From what I've read, I'd have to use mipmaps to use trilinear filtering, which would drive memory usage up, so I'd rather not. I know the final sizes of all the textures when they are loaded, so can't I somehow size them correctly at that point? (Using some form of texture filtering).

  Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >