Search Results

Search found 14646 results on 586 pages for 'installation guide'.

Page 413/586 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Boot camp with Vista crashes on startup

  - by Mark Pim

  I have a 2006 vintage MacBook Pro (Intel Core 2 Duo) and have been using Boot Camp since it was in beta. I had been running XP SP2 on it with Tiger quite happily. I've recently wiped and reinstalled everything to upgrade to Leopard. After installing Leopard, I fired up the Boot camp assistant and used it to install the Windows 7 RC. That worked really nicely, but my HFS+ driver didn't work under Windows 7 yet so I decided to install Vista instead. I didn't repartition the drive, just launched the Vista installation disk from BIOS and told it to overwrite the existing Windows 7 install. It installed fine and I installed the Boot Camp drivers, still all fine. Now, however, every time I boot into Windows and login it hard reboots itself as the desktop is appearing. After this it works fine again. Until the next power off. Has anyone had any similar problems? Or can offer suggestions on how to solve this?

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• How the computer could be used by two users at the same time

  - by user59595

  Running windows 7 64, Is there any application that allows me to connect an additional keeyboard and mice and monitor, so that this can be used by other user at the samee time while I use the main computer, There is an application called cpnmouse but it doesnt work on win7, betwin crashes before win7 start up, teamplayer is too expensive Has anyone figured out this functionality maybe with virtual machinees or something, i've tried team player in a virtual machine but it crashes I have 3 monitors one of theem is a Tv, i would like that my girlfried uses it as a terminal without me loosing the focus cause she uses the mice There is a linux software called userful, but it's linux and doesnt work for me, and windows multipoint server needs a clean installation and also that's not a valid choice

  Read the article

• Cannot install netbeans on Gentoo

  - by siebz0r

  I'm trying to install Netbeans on my Gentoo system and I just cannot get it to work. When I'm compiling it It fails due to not being able to locate org.apache.maven.project.MavenProject. [nb-javac] class file for org.apache.maven.project.MavenProject not found I'm suspecting it has something to do with the installation not being able to find several files. However these are reported as warnings. The missing files have a version in their filenames, the files that are on the disk have a version number that is slightly off. So that explains why these cannot be found. The full output of the install can be found here: http://pastebin.com/43NS2ktz

  Read the article

• how to automatically accept license with mounting mac osx .dmg files from command line?

  - by Vitaly Kushner

  Im automating my mac installation using 'puppet'. as a part of it I need to install several programs that come in a .dmg format. I use the following to mount them: sudo /usr/bin/hdiutil mount -plist -nobrowse -readonly -quiet -mountrandom /tmp Program.dmg The problem is that some .dmg files come with a license attached, and so script is stuck accepting the license. (there is no stdin/out when running with puppet, so I can't manually approve it to continue). Is there a way to pre-approve or force-approve the license?

  Read the article

• Detect damage done by virus

  - by user38471

  Hey, this morning after I went to college a virus infected my pc without any user interaction at my end. When I came home my computer was completely frozen and infected with lots of trojans. I have not typed anything important since returning so keys cannot be logged. However I want to know exactly when my computer crashed from the time of infection to see what could potentially be done remotely by a hacker. The virus my pc was diagonosed with was "fakespypro" http://www.microsoft.com/security/portal/Threat/Encyclopedia/Entry.aspx?Name=Win32%2fFakeSpypro on a fully updated windows 7 installation with firewall enabled. My computer was connected to an internal dorm room network, so probably that has had to do something with it. Any further information about how I could backtrace this virus infection or ways to discover what data might be stolen would be greatly appriciated.

  Read the article

• Python and mod_wsgi path issue

  - by jasonh

  I have an AIX 6.1 system that I've compiled and installed: Apache 2.2.21 (into /usr/local/mercurial) Python 2.7.2 (into /usr/local/bin and /usr/local/lib) mod_wsgi 3.3 (with the AIX fix #1 described here) Mercurial 2.0 (system-wide) However, when Apache starts, I get the following message in error_log: IOError: invalid Python installation: unable to open /usr/local/bin/lib/python2.7/config/Makefile (No such file or directory) See the problem? bin/lib doesn't exist. /usr/local/lib/python2.7/config/Makefile does exist though. However, I can't figure out where it's getting that path from. Here's the environment variables I've got: PYTHONHOME=/usr/local/bin PYTHONPATH=/usr/local/lib/python2.7 LIBPATH="/usr/local/mercurial/lib:$LIBPATH" PATH=/usr/local/bin:/usr/local/lib:$PATH LDR_CNTRL="MAXDATA=0x80000000" AIXTHREAD_SCOPE=S AIXTHREAD_MUTEX_DEBUG=OFF AIXTHREAD_RWLOCK_DEBUG=OFF AIXTHREAD_COND_DEBUG=OFF SPINLOOPTIME=1000 YIELDLOOPTIME=8 MALLOCMULTIHEAP=considersize,heaps:8 I've tried all sorts of combinations with and without PYTHONHOME, PYTHONLIB and PATH in envvars. My PATH, in case it matters is: /usr/bin:/etc:/usr/sbin:/usr/ucb:/usr/bin/X11:/sbin:/usr/opt/ifor/bin:/usr/local/bin:.

  Read the article

• Microsoft Office 2010 Proofing Tools Kit

  - by Svish

  I have installed the Office 2010 available on MSDN, but there is no proofing tools kit available there yet. Still I see various sources where I can download this kit when I search for it on Google. Is the Proofing Tools Kit available yet or not? Are these sources I see on Google legitimate ones or should I stay away from them? Or are they also available from Microsoft directly somewhere I haven't looked yet? 2010-07-28 Bump: Has anything come out now? I found something called a language pack on MSDN, but the installation looked pretty much the same as the original... not quite sure what that pack did...

  Read the article

• Browsing not working in Windows 8

  - by Jonathan Perry

  I'm using Windows 8 Professional installed on Windows 7 using the "Save my preferences and apps" installation option. The Windows works great, apps are downloading and I can listen to online radio stations using the TuneIn radio app meaning the internet connection is alive, however, when I open a browser (either Chrome or IE10) and try to browse the internet, I'm getting an "Unable to resolve DNS" error message. Prior to installing the internet browsing worked flawlessly I must say. I'm using ESET NOD32 Antivirus so I suspect that it might interfere with the web connection now, but I'm not so sure. Internet options show that the PC is set to resolve the DNS automatically. I don't know what to do. My other Win7 PCs in my wifi home network are connecting to the internet without any issues. If anyone can help me resolve this I'll be grateful :) Thanks

  Read the article

• SQL 2008 network logon

  - by gledhilla

  Hi I have a domain controller that I have installed active directory onto and have set up an account that I want to use for my SQL server installation on another computer that is linked onto the domain. I can search for the account in active directory and I am able to select it into the add new user section in MSSMS, however, when I click add I get 'Windows NT user or group 'DOMAIN\user' not found. Check the name again. (Microsoft SQL Server, Error: 15401) I have googled the Error code and I havent found a solution that has fixed the error. If you have any help I would be greatful Thanks :)

  Read the article

• I'm running Ubuntu notebook on a USB drive with 1GB persistence. Where are my XAMPP files?

  - by CDeanMartin

  I just began running Ubuntu Notebook on my 2GB USB stick, with 1GB persistence. After I installed XAMPP, I rebooted to make sure the persistence was working. It worked! My XAMPP installation worked, and it comes up when I type localhost into the browser. The sample apps work, including the ones using MySQL. But I can't find the application files! I am used to the vast labyrinth of files in Windows Explorer, and looking through 'Files and Folders' in GNOME, there seem to only be 7 or 8 folders in the entire OS? What is really going on here? I looked through them all and where is XAMPP? When I code PHP with a WAMP stack, all the .php files go in the 'WWW folder' What is the Linux equivalent of the WWW folder?

  Read the article

• Can I change the system's "Browse for Folder" dialog globally?

  - by Chris Phillips

  As far as I know, everyone hates the "Browse for Folder" dialog: This dialog is always too small, rarely remembers locations well, and worst of all: forces you to navigate your entire computer using a tedious tree structure. Now, to be fair, some of the problems are likely to do with how apps are invoking the control -- not setting a size or a default directory, etc. But the problem about the tedious tree control remains. Is there any way to customize your Windows installation to use a different control? Preferably an app/installer that does it for you safely, but dropping in a compatible DLL or similar technique would be okay too. Or are we stuck with this terrible control forever?

  Read the article

• Graphic driver for Targa Now NT9231

  - by Lumio

  I thought of installing Xubuntu on my elder Targa Now nettop and didn't think about the driver option. So now I'm here with a fresh Xubuntu installation and looking for graphic drivers. I found someone who might have had a "good" result with SiS - and the package is already installed, but I can't get my xorg.conf right. This is how my xorg.conf looks like right now: Section "Device" Identifier "Configured Video Device" Driver "sis" EndSection Section "Monitor" Identifier "Screen 0" Modeline "1024x768_60.00" 64.11 1024 1080 1184 1344 768 769 772 795 -HSync +Vsync #HorizSync 30.0-62.0 #VertRefresh 50.0-70.0 EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1024x768" "800x600" EndSubSection EndSection Thanks for every help given!

  Read the article

• Can a 32-bit RHEL4 userland work with a 64-bit kernel?

  - by James

  Is there a way to change an i386 RHEL4 machine to run an amd64 kernel, but ensure that it still builds software into same i386 binaries? On Debian this seems quite straightforward: just install an amd64 kernel (worst case, build one like this guy: http://www.debian-administration.org/users/jonesy/weblog/1) and prefix everything with "linux32". Then everything that considers uname -m will be unchanged, I just need to handle the few cases that consider uname -r. What is the Red Hat equivalent? Is the only way a full 64-bit installation on another disk and then chrooting back to the 32-bit system before anyone builds anything? (Even the best examples of that seem to be Debian-based.) Background: We make a large system that runs on (a variant of) i386 RHEL4. However, some of the larger RHEL build machines now have enough RAM that they might benefit from going 64-bit (for the kernel and maybe some of the bigger build steps). Our build system doesn't support cross-compilation.

  Read the article

• jZip isn't integrating with Windows 7 shell

  - by Aayush

  I installed jZip in my new windows 7 64 bit OS. but it doesn't seem to integrate with the shell. It doesn't appear in the right click menu on any file(not even zip files). To zip a file I have to open jZip go to file-new and browse for the files and to extract compressed files I have to open the file in jZip then click on extract, there is no right click menu integration what so ever, although It used to have when I had jZip on the Windows 7 RC. I reinstalled checking the settings incase I made a mistake but I checked shell integration while installation. Don't know what it wrong? anyone know how I should solve this. Help..? Thanks!

  Read the article

• Clear / Flush cached memory

  - by TheDave

  I have a small VPS with 6GB RAM hosting a couple of websites. Recently I have noticed that my cached memory size is quite high - see below: Cpu(s): 0.1%us, 0.1%sy, 0.0%ni, 99.1%id, 0.0%wa, 0.2%hi, 0.4%si, 0.0%st Mem: 6113256k total, 5949620k used, 163636k free, 398584k buffers Swap: 1048564k total, 104k used, 1048460k free, 3586468k cached After investigating if there is some method to have this flushed or cleared I stumbled upon a command which is: sync; echo 3 > /proc/sys/vm/drop_caches I read it could be useful to add this to a chron-task/job. Is this method recommended or could this lead to potential problems? The only concern I have is that I use one Magento installation on Memcached - could this have any negative effects on it? I am certainly not a pro therefore I would very much appreciate some expert advise. PS: My VPS runs on CentOS 5 x64 and I have WHM + NGINX installed.

  Read the article

• How to monitor a folder for changes, and execute a command if it does, on Windows?

  - by Camilo Martin

  There are similar questions for Linux and Mac, but I'm after a Windows solution here. The problem is as follows: I want to write several (js) script files in a folder, and have a program monitor that folder for file changes and new files being added, and run a command whenever that happens (to compile them all into one single file). The solution has to: Monitor both file changes and new files being added, in a folder. Run a command only if there is any change. It would be best if it either is a built-in solution (like a JScript or VBscript snippet), or something that does not require installation.

  Read the article

• opening Dbf files in oracle 10g

  - by nagaraju

  This nagaraju,from India,Hyderabad. I have installed oracle 10g trail version in my system(E drive),created one database with my name(database:-nagaraju),in that created tables, prodecures ,functions ,sequences etc for my project. Due to some sudden problem,i formatted my machine C drive,now iam not ablle to open my database, i need all procedures ,tables which i created in that. Now I newly installed oracle10g again in another folder,how can i copy my old database into my inew installation database. Or can i copy the script of procedures so that ican run in new database. I have all data in Oradata folder,like DBF files etc. Could you please help me, how to do that?

  Read the article

• Installing IIS on MS Windows Server 2003

  - by Vafello

  I have a Windows Server 2003 and asp.net website running on localhost. I have to install php and mysql, but php installation doesn't work for whatever reason. I was wondering if I could install package such as xampp on windows server to save time and hassle installing in manually (I could not find a tutorial for this). I was wondering though, if it is safe, i.e. what will happen if I go to http://localhost/ - will I get the php or asp website? In general, is it safe to install xampp on windows server 2003? All advice greatly appreciated

  Read the article

• "This CPU is not compatible with 64-bit mode." - Installing Windows 7 Ultimate 64-bit on a netbook with a 64-bit Intel Atom CPU

  - by galacticninja

  I tried installing Windows 7 Ultimate SP 1, 64-bit on a netbook (Lenovo IdeaPad S110), which has the Intel Atom N2800 (1.86 GHz) as its processor, but I get the following error message when the Windows 7 installation DVD is loading: It says "Attempting to load a 64-bit application, however this CPU is not compatible with 64-bit mode". The Intel Atom N2800 is a 64-bit CPU according to its webpage. I am wondering why the Windows 7 installer shows this error message, despite this. Is there something I must configure first before installing Windows 7, 64-bit? Or is the netbook not compatible with a 64-bit OS? I am trying to format the netbook and install Windows 7 Ultimate 64-bit, instead. Other details: The netbook has 2 GB RAM. The netbook initially had Windows 7 Starter (32-bit) installed.

  Read the article

• Setting up Tornado with Nginx on Ubuntu 10.04 for production use

  - by DjangoRocks

  Hi all, I understand that there's an nginx configuration file at http://www.friendfeed.com But i don't really know how to set up Tornada for production use on Ubuntu 10.04 with Nginx. Here's my situation and assumptions: 1) Assuming my Tornado project is set up as such: project/ src/ static/ templates/ project.py And I have installed Tornado by downloading the repositary from Github and than sudo python setup.py install 2) I've installed Nginx and started it based on the instructions here : http://library.linode.com/web-servers/nginx/installation/ubuntu-10.04-lucid My questions are: Where does my nginx configuration file go ? Within the src/ folder? After configuring Nginx, how do I start my Tornado project?

  Read the article

• What is the lease irriating printer manufacturer?

  - by aireq

  Currently I have a Lexmark all in one printer/scanner which has some of the worse drivers I've seen for a printer. The installation takes forever. Then once it's installed the printer will only work if I keep the "Lexmark Productivity Studio" running in my system tray. Then later after I've scanned something 99% of the time the "Save to PDF" button doesn't do anything when I click it. It is also a wireless printer, but of course the only way to set any of the wireless settings is during the driver setup. So if my WEP key changes then I have to go off and reinstall the entire printer driver. Lately I tried refilling one of the ink cartridges with a key I bought off amazon, and now both the printer and the drivers keep complaining about being out of "Official Lexmark Ink" This comic from The Oatmeal pretty much sums up my feelings about consumer printers and their drivers. This question is, of course, pretty subjective but I'd like to know what (if any) consumer printer brands actual provide quality drivers and software with their printers.

  Read the article

• Migrating from MyISAM to XtraDB

  - by Wringley

  Just a few questions that I just can't find anywhere about migrating to XtraDB. My group has been using MyISAM dbs for production and was wondering how hard is it to migrate to Percona's XtraDB and how would you go about doing so? Would I have to migrate MyISAM to InnoDB first or can I go straight to XtraDB? I installed Percona Server with XtraDB package on my Fedora machine but the documentation isn't very helpful as to how to use it so I was wondering does Percona just piggyback on a standard MySQL installation or is it a separate entity? Links to documentation on how to solve my questions would be fantastic. Thanks, Server Newbie.

  Read the article

• Why my /usr/share/file/magic is not found, in PHP at CentOS?

  - by Vincenzo

  This is what I'm doing: $ php <?php $finfo=finfo_open(FILEINFO_MIME, '/usr/share/file/magic'); This is what I'm getting: PHP Notice: finfo_open(): Warning: description `8-bit ISDN mu-law compressed (CCITT G.721 ADPCM voice data enco' truncated in - on line 2 PHP Notice: finfo_open(): Warning: description `8-bit ISDN mu-law compressed (CCITT G.721 ADPCM voice data enco' truncated in - on line 2 PHP Notice: finfo_open(): Warning: <= not supported in - on line 2 PHP Notice: finfo_open(): Warning: <= not supported in - on line 2 PHP Notice: finfo_open(): Warning: <= not supported in - on line 2 PHP Notice: finfo_open(): Warning: >= not supported in - on line 2 PHP Warning: finfo_open(): Failed to load magic database at '/usr/share/file/magic'. in - on line 2 This is a clean CentOS 5.5 installation, PHP 5.3. The file /usr/share/file/magic exists and is accessible.

  Read the article

• Checking whether product key will work with SBS 2003

  - by Rob Nicholson

  We've recently absorbed a small company who had a Dell PowerEdge server running SBS 2003. For some reason, the hard disks have been wiped. We have the product key though from the sticker on the side of the case but not the installation media: Win SBS Std 2003 1-2 CPU 5-CAL OEM software We do have a Dell labelled set of four CDs labelled SBS 2003 in our store and I've built a VM from this media but it doesn't prompt for the product key during install. Is there any way to ascertain whether this media will work with this product key without going through activation? I know one can activate several times but would prefer to check we've got the right media before doing this. Thanks, Rob.

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >