Search Results

Search found 13324 results on 533 pages for 'send on behalf of'.

Page 413/533 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

  - by Jander

  I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

  Read the article

• Is this way of using Excel 2007 Pivot table for BI scalable ?

  - by Sim

  Hi all, Background: We need to consolidate sales data across the country to do analysis Our Internet connection/IT expertise/IT investment is not quite strong, therefore full BI solution is out of question I tried several SaaS BI solution (GoodData, ZohoReports) and while they're good, they seem not to fully support what we need We're looking at 'bout 2 millions record for every 2 months My current approach Our (10) sites currently gathers data from all their branches and consolidate them into 1 Excel file with Pivot table and embed source data In HQ, I will request 10 sites to send back those Excel files periodically We will import those Excel to our MSSQL server There will be a master Excel file, that will also have the same pivot table (as those came from site Excel file), and datasource is the MSSQL server More details For testing, I currently use MSSQL 2008 Express on my laptop So far, I imported our transactions for the past 2 months and there are 2 millions+ row in 1 table in MSSQL (we just use 1 table, corresponding to our common pivot table structure). DB size is ~ 600 MB In the master Excel file, if not including the source data, it's just < 10MB. Including the source data will increase the size to 60 MB (so I supposed Office 2007 automatically zip the data ?) I try using the Pivot (drag-and-drop fields) and the performance so far is OK (my laptop specs: C2D T7200, 3GB RAM, Windows XP) So my question is : If we're looking at full year transaction (roughly 15 millions rows in MSSQL 2008 Express, 3.6 GB in size), is there any issue with that 15 million rows in 1 table in SQL Express ? Is there any performance issue with the pivot table at that time ? Can it still embed the source data ? (I google-ed but didn't find the maximum size of source data Excel 2007 can embed) Any other suggestions on how we can better do this ? Given that we can't afford the full BI solution, any light-weight/budget/SaaS BI that you can recommend ? Thanks

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• QMail do not delivery to remote mailboxes for my own domain

  - by lorenzo-s

  Sorry for the title, I don't know how to sum up this situation. I have a web server at mydomain.com, running qmail for website related mail delivery (i.e. newsletter, sign up confirmation, etc). qmail here is used only to send mails, because I have a fully working Google App Gmail associated with mydomain.com for normal email receiving. qmail runs fine when sending email to remote addresses, for example to [email protected], but fails when sending to [email protected]. I think it's because the server thinks that he have to manage mailboxes for mydomain.com locally, instead of redirect them to Gmail. Here is the /var/log/qmail/current for two email: the first one is sent without problems to example.com, second one fails because it's for mydomain.com: 2012-11-15 15:04:11.551933500 new msg 262580 2012-11-15 15:04:11.551936500 info msg 262580: bytes 5604 from <[email protected]> qp 5185 uid 33 2012-11-15 15:04:11.575910500 starting delivery 316: msg 262580 to remote [email protected] 2012-11-15 15:04:11.575912500 status: local 0/10 remote 1/20 2012-11-15 15:04:12.189828500 delivery 316: success: 74.125.136.27_accepted_message./Remote_host_said:_250_2.0.0_OK_1352991894_j49si13055539eep.9/ 2012-11-15 15:04:12.189830500 status: local 0/10 remote 0/20 2012-11-15 15:04:12.189831500 end msg 262580 2012-11-15 16:49:20.270332500 new msg 262580 2012-11-15 16:49:20.270336500 info msg 262580: bytes 2192 from <[email protected]> qp 5479 uid 33 2012-11-15 16:49:20.315125500 starting delivery 323: msg 262580 to local [email protected] 2012-11-15 16:49:20.315128500 status: local 1/10 remote 0/20 2012-11-15 16:49:20.320855500 delivery 323: failure: Sorry,_no_mailbox_here_by_that_name._(#5.1.1)/ 2012-11-15 16:49:20.320858500 status: local 0/10 remote 0/20 2012-11-15 16:49:20.372911500 bounce msg 262580 qp 5484 2012-11-15 16:49:20.372914500 end msg 262580 As you can see, it says: Sorry,_no_mailbox_here_by_that_name I can't say he's wrong :) How to solve this? How to let Google App Gmail manage incoming email for mydomain.com for messages sent by mydomain.com qmail server?

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Gathering buslogic SCSI hardware and virtual machine operating system

  - by Julian

  I'm trying to use Powershell to get SCSI hardware from several virtual servers and get the operating system of each specific server. I've managed to get the specific SCSI hardware that I want to find with my code, however I'm unable to figure out how to properly get the operating system of each of the servers. Also, I'm trying to send all the data that I find into a csv log file, however I'm unsure of how you can make a powershell script create multiple columns. Here is my code (almost works but something's wrong): $log = "C:\Users\me\Documents\Scripts\ScsiLog.csv" Get-VM | Foreach-Object { $vm = $_ Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic" } | Foreach-Object { get-VMGuest -VM $vm } | Foreach-Object{ Write-output $vm.Guest.VmName >> $log } } I don't receive any errors when I run this code however whenever I run it I'm only getting the name of the servers and not the OS. Also I'm not sure what I need to do to make the OS appear in a different column from the name of the server in the csv log that I'm creating. What do I need to change in my code to get the OS version of each virtual machine and output it in a different column in my csv log file? EDIT: Here's a more in depth look at things I've tried that have all failed: Get-VM | Foreach-Object { $vm = $_ $svm = Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic" } Foreach-Object {get-VMGuest -VM $svm } | Foreach-Object{Write-output $svm >> $log} } #Get-VM | Foreach-Object { # $vm = $_ # Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic"} #| write-host $vm # | Foreach-Object { # # #get-VMGuest -VM $_ | # #write-host $vm # #get-VMGuest -VM $vm } | Foreach-Object{ # #write-output $vm.VmName >> $log # #write-output $vm.guest.VmName, get-VmGuest -VM $vm >> $log NO GOOD # # Write-host $vm.Guest.VmName #+ get-vmGuest -vm $VM >> $log # # # } # } I'm not sure why get-VmGuest fails though. I'm getting the scsi hardware, filtering the hardware to only get buslogic, and then wanting to get the operating system of just the filtered VMs. I don't see where my code fails though.

  Read the article

• Postfix message ID originating process?

  - by Anders Braüner Nielsen

  Last night my postfix mail server(Debian Squeeze with dovecot, roundcube, opendkim and spamassassin enabled) started sending out spam from a single domain of mine like these: $cat mail.log|grep D6930B76EA9 Jul 31 23:50:09 myserver postfix/pickup[28675]: D6930B76EA9: uid=65534 from=<[email protected]> Jul 31 23:50:09 myserver postfix/cleanup[27889]: D6930B76EA9: message-id=<[email protected]> Jul 31 23:50:09 myserver postfix/qmgr[7018]: D6930B76EA9: from=<[email protected]>, size=957, nrcpt=1 (queue active) Jul 31 23:50:09 myserver postfix/error[7819]: D6930B76EA9: to=<[email protected]>, relay=none, delay=0.03, delays=0.02/0/0/0, dsn=4.4.2, status=deferred (delivery temporarily suspended: lost connection with mta5.am0.yahoodns.net[66.196.118.33] while sending RCPT TO) The domain in question did not have any accounts enabled but only a catchall alias set through postfixadmin - most emails were send from a specific address I use frequently but some were also sent from bogus addresses. None of the other virtual domains handled by postfix were affected. How can I find out what process was feeding postfix/sendmail or more info on where they originated? As far as I can tell php mail() wasn't used and I've run several open relay tests. I did a little tinkering(removed winbind from the server and ipv6 addresses from main.cf) after the attack and it seems to have subsided but I still have no idea how my server was suddenly sending out spam. Maybe I fixed it - maybe I didn't. Can anyone help figuring out how I was compromised? Anywhere else I should look? I've run Linux Malware Detect on recently changed files but nothing found.

  Read the article

• HP Power Manager SMTP setup doesn't have space for username & password

  - by Martha

  Is there some way to configure HP Power Manager to not assume that there's an email server running locally? We recently acquired an HP T1500 G3 UPS, which we're trying to control using HP Power Manager 4.2. The main reason we wanted to get this particular UPS is because it says it's capable of sending notifications (of the "Yo, the power's out, you may want to look into it" type) via email, as opposed to SNMP. Turns out, that's not entirely true. The server is running Windows Server 2003. It is not running an email server of any sort - we do that via two different providers. Outlook email is provided by Verizon, and our SMTP email service is provided by a small local company. When we use CDO to send auto-generated notification emails, we have to provide the SMTP server name, port, username, and password. The HP Power Manager interface only allows us to enter the server name and the username. Thus, not surprisingly, the emails never go anywhere. Help?

  Read the article

• Windows 7 Professional Cannot Connect to Share - Wrong password

  - by henryford

  I know that this question has actually been asked a few times before, but every solution I found didn't yield any results on my end, I can't get my head around it: When I am trying to connect to a share on the network, I always get the response "The specified network password is incorrect". However, the password is definetly correct and it works if I connect from another machine. I changed the LAN Manager authentication level to "Send LM & NTLM - use NTLMv2 session security if negiotated", I configured Kerberos encryption types to include all suites, rebooted (several times), but still - no luck. I can connect if I use my regular account with which I am logged in, but I need to connect with a different user since my log-in user has not enough privileges on the share. When I do that, the error above comes up. I'm really frustrated at the moment, this problem is driving me crazy. I'd be gladful for any possible solution to this. At the moment I'm using a workaround: I connect to a different machine via RDP, login with the user I have to use for the network-share connection and then I can map the drive and copy/paste from the RDP session to my local workstation. This is also working when I am connecting via RDP with my current login user and map the drive with the other user who has sufficent privileges. Tanks in advance, Thomas

  Read the article

• Why is Outlook 2007 resizing images in outgoing and incoming HTML email? How can I fix this?

  - by Mikuso

  In my Outlook 2007 client, embedded images in incoming emails appear resized when the message is viewed. The incoming images are resized to 198px wide, despite the original size. If it was larger, it will be shrunk; if it was smaller, it will be enlarged; the aspect ratio remains the same (the image is not stretched). This is local to my client only (i.e. another Outlook 2007 client reading the same IMAP inbox will see the image in the correct size. Similarly, viewing the email message in a browser will display the correct size). This happens regardless of whether width/height attributes are set on the image tag in the HTML. Zoom is set to 100% in my message window; text and other elements are not distorted from the original. In addition to this, outgoing HTML messages with images embedded in the same way are resized as they are sent. The outgoing images are all scaled to have a width of 247px. The source HTML of the outgoing message is changed after pressing Send so that the tag's width attribute is 247 pixels and the image file itself is also resized. These problems only occur with HTML messages; Rich Text messages do not have the same problem. I have already tried reinstalling Outlook and have it fully patched up to date. Why is this happening and how can I stop this?

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• Howto change Axis server-config.wsdd so that we don't expect a SOAPAction

  - by GKForcare

  The problem I'm facing is that the client of my service will never send me a SOAPAction header. How can I tell Axis to still map to the incomming call to my service implementation anyway. I did bump into tricks like adding a Handler like this: <handler name="ReportMapper" type="java:com.mycompany.project.ReportMapper"/> <transport name="http"> <requestFlow> <handler type="ReportMapper"/> <handler type="URLMapper"/> <handler type="java:org.apache.axis.handlers.http.HTTPAuthHandler"/> </requestFlow> <parameter name="qs:list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs:wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> <parameter name="qs.list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs.method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs:method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs.wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> </transport> but that did not help. The mapper is found during the creation of the WSDL but when calling the service, the invoke of the handler is not used. I do need to note that when I simulate the SOAP-call using @curl@ and I do add the SOAPAction header, the invoke is called. Any help would be most appreciated.

  Read the article

• Using my own Postfix, filtering spam and getting all the mail into my ISP's inbox

  - by djechelon

  Hello, I currently own a domain bought via GoDaddy.com, which provides me a basic email setup for the most common needs. I configured it to forward all mail to [email protected] to [email protected]. I also own a virtual server with a running Postfix that I use for a specific website (all mail to somedomain.com gets forwarded via LMTP to a program written by me). Since I'm recently experiencing some harassing by spammers, since GoDaddy doesn't seem to filter spam, and since my Windows Phone's Pocket Outlook cannot filter spam, I would like to use SpamAssassin to filter inbound spam by changing my domain's MX records to my server My ideal setup is the following: All mail delivered to somedomain.com gets redirected via LMTP as usual via virtual transport without any spam check All mail to [email protected] gets redirected to [email protected] after a severe spam check I don't care about [email protected] since I use just one address for now I would like to train SpamAssassin with customized spam rules, possibly based on the presence of certain keywords (links to certain unsubscribe pages I found recurring) I currently configured Postfix with transport somedomain.com lmtp:[127.0.0.1]:8025 .somedomain.com error: Cannot accept mail for this domain relay somedomain.com OK (I guess I should add mydomain.com OK too) virtual @mydomain.com [email protected] (looks like a catch-all rule, it's OK as requirement 3) I installed SpamAssassin, I can do rcspamd start and set it to boot with the server, but I don't know if there is anything else to do for use in Postfix, and how to apply requirement 1 (only mail to mydomain.com gets filtered) I also tried to send an email via Telnet to make sure my settings are ready for MX change. I received the message into my account but I found that it gone through secureserver.net, like Postfix didn't rewrite the destination but simply relayed the message. Thank you in advance. I'm no expert in SpamAssassin, and I have little experience in Postfix (enough to avoid making my server an open relay)

  Read the article

• Any program to help me check whether an ethernet channel can support full-length VLAN packet?

  - by Jimm Chen

  Sometimes, I have to face such a situation that I need to quickly and explicitly know whether a full length VLAN packet can traverse between two RJ45 ports. Yes, I mean 802.1Q ethernet frame with Etype=81 00 (diagram below). What I can do now is: Get two Windows PCs, for each PC, intall Intel Gigabit NIC and Intel specific driver to create a virtual NIC, with VLAN ID=3 assigned. Then connect the two PCs to each of the two RJ45 port. Finally execute ping to generate a full-length ethernet packet. ping -f -l 1472 <dest-IP> This way, I can be sure that the sent packet has the maximum "IP data payload" of 1500 bytes(8 bytes of ICMP header and 1472 bytes of ICMP data). If the ping gets reply, I know that the ethernet channel support full-length VLAN packet. From my experiment, some home switch or broad band routers(e.g. Linksys WRT54G) does not support full-length VLAN packet switching, so only ping -f -l 1468 succeeds. You see, I have to use an expensive Intel NIC to carry on that test, quite inconvenient. You know, for most laptop today, they do not equip an Intel NIC, and, even it is an Intel NIC, Intel VLAN driver, Intel has limitations on the models on which VLAN driver can be installed. So, my question is: Is there a small program that can let me send a full-length VLAN packet without installing a dedicated VLAN driver? Or better, the program has a stock feature that does the very job for my situation. Windows programs preferred, Linux solution welcome. Simpler the program, the better. Thank you.

  Read the article

• Howto change Axis server-config.wsdd sothat we don't expect a SOAPAction

  - by GKForcare

  The problem I'm facing is that the client of my service will never send me a SOAPAction header. How can I tell Axis to still map to the incomming call to my service implementation anyway. I did bump into tricks like adding a Handler like this: <handler name="ReportMapper" type="java:com.mycompany.project.ReportMapper"/> <transport name="http"> <requestFlow> <handler type="ReportMapper"/> <handler type="URLMapper"/> <handler type="java:org.apache.axis.handlers.http.HTTPAuthHandler"/> </requestFlow> <parameter name="qs:list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs:wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> <parameter name="qs.list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs.method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs:method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs.wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> </transport>

  Read the article

• Troubleshoot IIS 6 and Intermittent SQL Server Connectivity Loss

  - by jpsnow

  I am not a System Administrator, but I am temporarily trying to fill that role. I have 2 Windows 2003 Servers. 1 server has my Microsoft SQL Database (SQL Server 2005) and the other is the web server with IIS6. Intermittently (once every month or 2) the web server loses connectivity to the database server for a period of roughly 10 minutes. It normally regains connectivity without intervention. The website is set up to send me an email when there is a problem connecting to the database. Within the email, I get the error code: [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]SQL Server does not exist or access denied. I am able to access both servers during the outage. I can go to my SQL server and open up SQL server without any issues. I have looked in the EventViewer and do not see anything. The last time that I had this issue, I stopped IIS6 and started it. After doing this, the issue was resolved. This leads me to believe that it is an issue with IIS and not SQL server. How can I begin troubleshooting?

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• Sign multiple domains with single Domain Key (dk-filter)

  - by Lashae

  Motivation The private shopping website GILT, send periodical update emails from giltgroupe.bounce.ed10.net however all of the mails are signed with domain keys of giltgroupe.com. mailed-by giltgroupe.bounce.ed10.net signed-by giltgroupe.com My Story I couldn't manage to sign x.com with y.com 's domain key using dk-filter under Debian Lenny with postfix. If I try to init dk-filter service with following arguments: DAEMON_OPTS="$DAEMON_OPTS -d x.com,y.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" dk-filter service signs with domain x.com (d=x.com) If I change the daemon arg.s as following: DAEMON_OPTS="$DAEMON_OPTS -d x.com -c nofws -k -i /var/dk-filter/internal_hosts -s /etc/dk-keys.conf" then emails sent From y.com is not being signed. the dk-keys.conf file is as follows: *:/var/dk-filter/y.com/mail I managed to do same thing with DKIM, works perfect. However DK doesn't seem to work. I don't have any problem signing y.com's emails with y.com's key and x.com's emails x.com's key, which indicates there is no configuration problem. Do you have any experience/advice to make it possible to sign emails from multiple domains by a specific chosen domain?

  Read the article

• SSH Interactive mode not working

  - by Ekin Koc

  I have a Debian based linux server running for a year or so, without any problems. A couple of days ago, ssh interactive mode stopped working for no reason. I mean, I can open an ssh connection just fine, the server greets me with shell but I just can't type anything. However, if I send commands like this: ssh [email protected] cat /var/log/messages, I get the response. I dug through several logs and found one message, which feels remotely relevant to the problem; sh kernel: [10222733.062511] ------------[ cut here ]------------ sh kernel: [10222733.062522] WARNING: at /build/buildd-linux-2.6_2.6.32-39-amd64-7yVIH2/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/char/tty_ldisc.c:738 tty_ldisc_reinit+0x46/0x7b() sh kernel: [10222733.062526] Hardware name: PowerEdge R210 II sh kernel: [10222733.062528] Modules linked in: ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables x_tables sha1_generic arc4 ecb ppp_mppe ppp_async crc_ccitt ppp_generic slhc loop snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 i2c_core pcspkr evdev joydev dcdbas container button processor ext3 jbd mbcache sg sd_mod sr_mod crc_t10dif cdrom usb_storage usbhid hid mpt2sas ahci ehci_hcd libata scsi_transport_sas usbcore bnx2 nls_base scsi_mod fan thermal thermal_sys [last unloaded: scsi_wait_scan] sh kernel: [10222733.062568] Pid: 8662, comm: sshd Not tainted 2.6.32-5-amd64 #1 sh kernel: [10222733.062569] Call Trace: sh kernel: [10222733.062572] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b sh kernel: [10222733.062574] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b Is there any way to get back the sshd working in interactive mode? I tried restarting sshd but that is no help. And somehow, I can not reboot the server. Tried sending shutdown -r now and reboot but it refuses to go down. Should I go ahead and request a physical reboot?

  Read the article

• Undeliverable e-mail message from [email protected]

  - by QGfisher

  I am responsible for IT for a small charity and we have a problem with a few individuals who e-mail us on our hosted e-mail addresses. The individual is on btconnect and our server is also on BT broadband and using MSExchange. I understand that the message from [email protected] are generated by Exchange but can't tell whether this is a problem with our server (seems unlikely as most people send and receive e-mails perfectly well) or with the sender's server. I have copied a sample test message below and would be very grateful if somebody can explain what is causing this problem. I have * the personal details - hope that's acceptable but I don't want to compromise the individual's identity/security. ----- Original Message ----- From: "System Administrator" To: "****" <****.***@btconnect.com Sent: Tuesday, April 06, 2010 3:26 PM Subject: Undeliverable: Test Message Your message To: ***** Subject: Test Message Sent: Tue, 6 Apr 2010 15:25:59 +0100 did not reach the following recipient(s): ***@quiltersguild.org.uk on Tue, 6 Apr 2010 15:26:07 +0100 The e-mail account does not exist at the organization this message was sent to. Check the e-mail address, or contact the recipient directly to find out the correct address.

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• LYNC 2010 Dial-In in Meeting DTMF issue

  - by user140116

  We are facing an issue in the LYNC2010 dial-in to a meeting. We redirect an Asterisk number to LYNC, whitch connects successfully in the dial-in plan of LYNC. After calling from external network to the given number, we hear LYNC aswering and prompting us to enter the PIN and afterwards the hash key. I should mention that all other dials to LYNC from Asterisk and vise versa are routed successfully. Also all DTMF we send to Asterisk from the phone (IVR, Extension, PIN etc) are routed also fine Afterwards we press the appropriate pin folowed by the hash keyand we get 'Sorry I can't find meeting with that number' Some pros mentioned that it might be dtmfmode=RFC2833 or dtmfmode=auto in Asterisk (All checked and tried). Some pros mentioned, that there is a problem in geeral in LYNC and DTMF (even with Cisco Call Manager). Some other pros mentioned that chack box 'Enable refer support' in Voice Routinh\Trunk Configuration' in LYNC has to be unchecked (Also tested). The problem stil remains and there is no way to enter a meeting room by dial-in. ANY idea would be appreciated!!!!!!!!

  Read the article

• Changing a set-cookie header using mod_rewrite/mod_proxy

  - by olrehm

  I have a bunch of cgi scripts, which are served using HTTPS. They can only be reached on the intranet, not from the outside. They set a cookie with the attribute 'Secure', so that it can only be send via HTTPS. There is also a reverse proxy to one of these scripts, unfortunately using plain HTTP. When a response comes in from my cgi-script with a secure cookie, it is not being passed on via HTTP (after all, that is what that attribute is for). I need however, an exception to this rule. Is it possible to use mod_rewrite/mod_proxy or something similar, to change the set-cookie header in the response coming from my cgi script and remove the Secure, such that the cookie can be passed back to the user using the unsafe HTTP connection? I understand that this defeats the purpose of the Secure in the first place, but I need this as a temporary work around. I have searched the web and found how to add a set-cookie header using mod_rewrite, and I have also found how to retrieve the value of a cookie coming from the client in a cookie header. What I have not yet found is how to extract the set-cookie header received in the response of a script I am proxying for. Is that possible? How would I do that? Ole

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• What does "incoming" and "outgoing" traffic mean?

  - by mgibsonbr

  I've seen many resources explaining how to set up a server's firewall to allow incoming and outgoing traffic on HTTP standard ports (80 and 443), but I can't figure out why I would need either of them. Do I need to unblock both for a "regular" web site to work? For file uploads to work? Are there situations where it would be advisable to unblock one and leave the other blocked? Sorry if that's a basic question, but I couldn't find it explained anywhere (also I'm not a native english speaker). I know in a "regular" web site the client is always the one who initiates a request, so I'm assuming a web server must accept incoming traffic on those ports, and my common sense tells me the server is allowed to send a response without unblocking anything else (otherwise it wouldn't make sense to have two types of rules). Is that correct? But what is an outgoing web (service) traffic, and what would be its use? AFAIK if the server wanted to initiate a connection with another machine, the specific port that matters is the one in the other end (i.e. the destination port would be 80), on its end any free port could be used (the source port would be random). I can open HTTP requests from my server (using wget for instance) without unblocking anything. So I'm assuming my concepts of "incoming" and "outgoing" are wrong somehow.

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >