Search Results

Search found 26263 results on 1051 pages for 'linux guest'.

Page 421/1051 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• SSH connection falling down

  - by kappa

  I've set up a connection with autossh that creates some tunnels at system startup, but if I try to connect, after successful login (with RSA key) connection fall down, here a trace: debug1: Authentication succeeded (publickey). debug1: Remote connections from LOCALHOST:5006 forwarded to local address localhost:22 debug1: Remote connections from LOCALHOST:6006 forwarded to local address localhost:80 debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: remote forward success for: listen 5006, connect localhost:22 debug1: remote forward success for: listen 6006, connect localhost:80 debug1: All remote forwarding requests processed debug1: Sending environment. debug1: Sending env LANG = it_IT.UTF-8 debug1: Sending env LC_CTYPE = en_US.UTF-8 debug1: client_input_channel_req: channel 0 rtype exit-status reply 0 debug1: client_input_channel_req: channel 0 rtype [email protected] reply 0 debug1: channel 0: free: client-session, nchannels 1 Transferred: sent 2400, received 2312 bytes, in 1.3 seconds Bytes per second: sent 1904.2, received 1834.4 debug1: Exit status 1 What can be the problem? All this stuff is managed by a script already running on another machine (creating reverse tunnels on the same machine but with different ports)

  Read the article

• central log-server with auditdisp

  - by johan

  I want to setup a central log-server. The log-server is running with debian 6.0.6 and the audit daemon is installed in version 1.7.13-1. The Clients are running with Red Hat 5.5 and they connect to the log-server via audispd. The connection works fine and i get all messages from each node. My questions is: is it possible that the auditd daemon from the log server write the messages from each node in a separate file? I try to transfer the messages via the syslog daemon, that works but i can not use tools like ausearch to analyze these log-files.

  Read the article

• installing latest apache on centos

  - by fivelitresofsoda

  hi, I'm trying to install the newest version of apache on my centos server. I did the following: Download $ wget http://httpd.apache.org/path/to/latest/version/ Extract $ gzip -d httpd-2_0_NN.tar.gz $ tar xvf httpd-2_0_NN.tar Configure $ ./configure Compile $ make Install $ make install Test $ PREFIX/bin/apachectl start And that all worked except the last step, when i type apachectl start it says 'command not found'. I ran this command from /usr/local/apache2/bin/ where it is installed but no cigar. Any idea what i am doing wrong? Thanks.

  Read the article

• How do I measure or track the progress of a command on a GNU distro?

  - by Felipe Alvarez

  If I run cp file1 file2 I'd like to be able to track it's progress. Is there a command I can use for this? rsync --progress has this, but is there something generic, usable for "any" command?

  Read the article

• How to disable or tune filesystem cache sharing for OpenVZ?

  - by gertvdijk

  For OpenVZ, an example of container-based virtualization, it seems that host and all guests are sharing the filesystem cache. This sounds paradoxical when talking about virtualization, but this is actually a feature of OpenVZ. It makes sense too. Because only one kernel is running, it's possible to benefit from sharing the same pages of filesystem cache in memory. And while it sounds beneficial, I think a set up here actually suffers in performance from it. Here's why I think why: my machines aren't actually sharing any files on disk so I can't benefit from this feature in OpenVZ. Several OpenVZ machines are running MySQL with MyISAM tables. MyISAM relies on the system's filesystem cache for caching of data files, unlike InnoDB's buffer pool. Also some virtual machines are known to do heavy and large I/O operations on the same filesystem in the host. For example, when running cat *.MYD > /dev/null on some large database in one machine, I saw the filesystem cache lowering in another, monitored by htop. This essentially flushes all the useful filesystem cache in guests (FIFO) and so it flushes the MySQL caches in the guests. Now users are complaining that MySQL is very slow. And it is. Some simple SELECT queries take several seconds on times disk I/O is heavily used by other machines. So, simply put: Is there a way to avoid filesystem cache being wiped out by other virtual machines in container-based virtualization? Some thoughts: Choosing algorithm for flushing filesystem cache in the kernel. (possible? how?) Reserving a certain amount of pages for a single VM. (seems no option for filesystem cache type of pages that reading man vzctl) Will running MySQL on another filesystem get me anywhere? If not, I think my alternatives are: Use KVM for MySQL-MyISAM running VMs. KVM actually assigns memory to the VM and does not allow swapping out caches unless using a balloon driver. Move to InnoDB and tune the buffer pools, dirty pages, etc. This is now considered to be 'nice to have' on the long-term as not everyone responsible for administration of the system understands InnoDB. more suggestions welcome. System software: Proxmox (now 1.9, could be upgraded to 2.x). One big LV assigned for the VMs.

  Read the article

• Taking an image backup of an entire server?

  - by WarDoGG

  I am currently using a dedicated server for my hosting needs. However, the costs are too high and I would like to suspend everything until I work out my business strategy again. Is there a way I can take a complete backup of the filesystem and run it in VMWare ? I cannot just copy the entire filesystem because there are lots of tools installed and tight changes to the server configuration files I myself dont know about (by the developers), but I need a snapshot of the entire disk image along with processes installed and everything is as is because for development needs, I need to work on this copy in VMWare or VirtualBox etc. Is it possible for me to take a full image copy ? How do I do it ?

  Read the article

• Cannot boot NixOS Install CD

  - by InFreefall

  I am trying to install NixOS on an Acer laptop. When I try to boot off of the install CD, the system starts up and shows the Acer logo. Then, the boot menu of the CD appears, but it only displays on the top left corner of the screen. The rest of the screen still shows the Acer logo. If I try to select "boot" from the menu, that area of the screen goes black, and nothing else happens. I tried adding "nomodeset" to the boot arguments, but that did not affect anything. Are there any other boot arguments or anything else that could fix this?

  Read the article

• MySQL wants a password but it's empty

  - by gAMBOOKa

  mysql -uroot ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES) mysql -uroot -p Enter password: <-- leave blank, hit enter without entering anything mysql> <-- i am logged in NOTE: This is a new mysql instance installation So if the password is blank, why won't it log me in without a -p flag? For a little clarification. I am running into this issue when attempting to change the password using a script: We're using a bash script to do that. mysqladmin -u root password abc wouldn't work (access denied) mysqladmin -u root -p password abc cannot be used because it prompts for a password and we need to automate this. mysqladmin -u root -p'' password abc is not working either

  Read the article

• How Do I Use Multiple Versions of OpenSSL ... One for Apache and one for PHP

  - by Ken S.

  I have an Apache 2.2 (self-compiled version) server that is getting dinged during a PCI scan because it does not support TLS 1.1 or 1.2 ciphers. After some digging I found that the installed version of OpenSSL (0.9.8e) does not contain the newest TLS ciphers. So I went and downloaded and compiled the latest version of OpenSSL (1.0.1c) and have it installed in an alternate location within /opt so it wouldn't interfere with the installed version. What I would like to do is to compile Apache against the 1.0.1 libraries and keep the system-installed libraries for use with PHP, cURL, openssh, etc. I'm hoping that doing it this way will allow Apache to use the newest TLS but not break anything with any other programs that require the old libraries. I thought I could do this by adding an entry in to /etc/ld.so.conf that pointed to the new libraries, but I think this will conflict with the existing ones. i.e. two references to libcrypto could cause everything to have issues. The main reason for doing this is because of issues with PHP cURLing to external servers and having issues with the latest OpenSSL libs thus requiring edits to our PHP code. Would love some guidance on how best to accomplish this.

  Read the article

• end_request: I/O error, dev sda, sector xxxxxxxxx

  - by muruga

  I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. After that I am getting the following error message in kern.log and demsg kernel: [65896.678870] end_request: I/O error, dev sda, sector 17430271 kernel: [69263.783957] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK : [69263.783957] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] kernel: [69263.783957] sd 0:0:0:0: [sda] Add. Sense: Internal target failure Whether it is kernel problem or hard disk problem or Raid problem

  Read the article

• Very high memory usage, but not claimed by any process?

  - by SharkWipf

  While stress-testing LVM on one of our Debian servers, I came across this issue where memory would fill up a lot to the point where it would run the server out of memory, but no process would claim the memory. See http://i.imgur.com/cLn5ZHS.png, and see http://serverfault.com/a/449102/125894 for an explanation on the colors used in htop. Why is this happening? And is there any way to see what process is using the memory? Htop is configured not to hide any processes, so what is it that htop is missing? In this particular case, I can fairly certainly say that it is caused, directly or indirectly, by lvmcreate, lvmremove or dmsetup, as I was stress-testing that. Do note that this question is not about solving the LVM problem, but about why the memory isn't claimed by any process. Stopping all LVM commands does bring the memory back down to <600MB.

  Read the article

• compressing dd backup on the fly

  - by Phil

  Maybe this will sound like dumb question but the way i'm trying to do it doesn't work. I'm on livecd, drive is unmounted, etc. When i do backup this way sudo dd if=/dev/sda2 of=/media/disk/sda2-backup-10august09.ext3 bs=64k ...normally it would work but i don't have enough space on external hd i'm copying to (it ALMOST fits into it). So I wanted to compress this way sudo dd if=/dev/sda2 | gzip > /media/disk/sda2-backup-10august09.gz ...but i got permissions denied. I don't understand.

  Read the article

• Limiting and redirect port access with useragent

  - by linuxcore

  I'm trying to write iptables string match rule To block http://domain.com:8888 and https://domain.com:8888 when it matches the supplied string in the rule. And another rule to redirect the ports also from 8888 to 7777 I tried following rules but unfortunately didn't work iptables -A INPUT -p tcp -s 0.0.0.0/0 -m string --string linuxcore --algo bm --sport 8888 -j DROP iptables -t raw -A PREROUTING -m string --algo bm --string linuxcore -p tcp -i eth0 --dport 8888 -j DROP iptables -t nat -A PREROUTING -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j REDIRECT --to-port 7777 iptables -A INPUT -t nat -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j DROP I want to do this from iptables not the webserver because the server may not have a webserver and those ports are working on internal proxy or something like ..etc

  Read the article

• circumstances where software change leads to device damage

  - by nerorevenge

  Recently I changed a friend's OS from a really virus filled windows 7 to Ubuntu ..but kept changing os's because lsusb wouldn't detect the camera.But after coming back to windows, the camera wasn't detected, though I must point out the device driver for the camera was never found. The Sony 'technician' told me that that since the dev-manager of windows 7 couldn't detect the camera , irregardless of whether the device driver was installed, the software change must have damaged the hardware. I was wondering if there is any truth to it.

  Read the article

• gpasswd and access to a file or directory

  - by PeanutsMonkey

  As I understand it if I run the command gpasswd -A username directoryname I assign administrator privileges to username for the directory directoryname. This means that username is able to add new members to the group for directoryname without root privileges. Does this also mean that username belongs to the group or do I need to add username to the group using the commands usermod, gpasswd -a or gpasswd -M

  Read the article

• OpenVPN + iptables / NAT routing

  - by Mikeage

  Hi, I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

  Read the article

• Why can't Emacs on Mac OS X find the Info directory node?

  - by Scott Schulthess

  The default Emacs on Mac OS X, 22.1, appears to have some problems with the info/help stuff. When you hit C+h i, it says: Can't find the Info directory node. It works in AquaEmacs, but I downloaded the 23 version of emacs precompiled binaries from here and I still have the same problem.

  Read the article

• Does rsync support multiple sources to a given destination in parallel

  - by KM

  If I have multiple sources, each with the same directory tree, but different files in the tree, is it safe to run multiple rsync commands in parallel with the same destination? Specifically, will there be any race conditions for directory/file creation?

  Read the article

• Daemons did not start automatically ubuntu 10.04

  - by Anton Prokofiev

  Hello, All! I have a strange behavior on Ubuntu 10.4: few daemons (apache2 and postgresql (8.4SS from enterpriseDB) did not start automatically. Funny things that time-to-to they do. (If I just restart my computer everything looks ok, but if I turn it off for the night, nothing work..., so I have to start them manually) I've googled this problem a little bit, but the only answer I have found was to run: sudo update-rc.d apache2 defaults I've called it but the answer was: System start/stop links for /etc/init.d/apache2 already exist. Any Ideas?

  Read the article

• How can I make subversion reset the stored passwords/users and remember my authentication credential

  - by NicDumZ

  Hello folks! Background: I used to have everything working just fine on my fresh install: $ svn co https://domain:443/ test1 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn co https://domain:443/ test2 # checkouts nicely, without asking for my password. At some point I needed to commit stuff using a different account. So I did that $ svn ci --username other.user Authentication realm: <https://domain:443> Subversion repository Password for 'other.user': # works fine But since then, everytime I want to commit as 'nicdumz' (default user, all repos have been checked-out with that user), it prompts me for my password: $ svn ci Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': Hey come on, why :) The same happens if I want a fresh checkout, since read-access is also protected. So I tried fixing the issue by myself. I read around that ~/.subversion/auth was storing credentials, so I removed it from the way: $ cd ~/.subversion $ mv auth oldauth $ mkdir auth It seemed to work at first, because svn had forgotten about certificate validation: $ svn co https://domain:443/ test3 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn up Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': What? how is this happening? If you have suggestions to investigate more about the behaviour, I am very interested. If I'm correct, there is no way to do a verbose svn up or anything of the like, so I'm not sure should I go for investigation. Oh, and for what it's worth: $ svn --version svn, version 1.6.6 (r40053) compiled Oct 26 2009, 06:19:08 Copyright (C) 2000-2009 CollabNet. Subversion is open source software, see http://subversion.tigris.org/ This product includes software developed by CollabNet (http://www.Collab.Net/). The following repository access (RA) modules are available: * ra_neon : Module for accessing a repository via WebDAV protocol using Neon. - handles 'http' scheme - handles 'https' scheme * ra_svn : Module for accessing a repository using the svn network protocol. - with Cyrus SASL authentication - handles 'svn' scheme * ra_local : Module for accessing a repository on local disk. - handles 'file' scheme * ra_serf : Module for accessing a repository via WebDAV protocol using serf. - handles 'http' scheme - handles 'https' scheme

  Read the article

• How to set up virtual users in vsftpd?

  - by ares94

  I've read this tutorial: http://howto.gumph.org/content/setup-virtual-users-and-directories-in-vsftpd/ My configuration is as follow: ---vsftpd.conf--- listen=YES anonymous_enable=NO local_enable=YES virtual_use_local_privs=YES write_enable=YES connect_from_port_20=YES pam_service_name=vsftpd guest_enable=YES user_sub_token=$USER local_root=/var/www/sites/$USER chroot_local_user=YES hide_ids=YES ---/etc/pam.d/vsftpd--- auth required pam_pwdfile.so pwdfile /etc/vsftpd/passwd account required pam_permit.so I created file /etc/vsftpd/passwd and added users using htaccess. I tried to login but it didn't work: ftp 127.0.0.1 Connected to 127.0.0.1 (127.0.0.1). 220 vsFTPd 2.3.5+ (ext.1) ready... Name (127.0.0.1:root): user1 331 Please specify the password. Password: 530 Permission denied. Login failed. Everything seems fine accept the permission denied thing. How can I fix this?

  Read the article

• How to start a service at boot time in ubuntu 12.04, run as a different user?

  - by Alex

  I have a server ClueReleaseManager which I have installed on a Ubuntu 12.04 system from a separate user (named pypi), and I want to be able to start this server at startup. I already have tried to create a simple bash script with some commands (login as user pypi, use a virtual python environment, start the server), but this does not work properly. Either the terminal crashes or when I try to ask the status of the service it is started and I am logged in as user pypi ...? So, here the question: What are the steps to take to make sure the ClueReleaseManager service properly starts up on boot time, and which I can control (start/stop/..) during runtime, while the service is running from a user pypi? Additional information and constraints: I want to do this as simple as possible Without any other packages/programs to be installed I am not familiar with the Ubuntu 12.04 init structure All the information I found on the web is very sparse, confusing, incorrect or does not apply to my case of running a service as a different user from root.

  Read the article

• How do I set up a virtual host?

  - by user1698332

  My router redirects port 80 to port 8080. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• Apache worker is crashing after 3.000 users

  - by user1618606

  I activated Apache Worker on my VPS and I'm having problems, 'cause the website is crashing when 3000 users are accessing the website. I'm using http://whos.amung.us/stats/2jzwlvbhvpft/ as counter. My Apache Worker configuration: KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 1 <IfModule mpm_worker_module> ServerLimit 20000 StartServer 8000 MinSpareThreads 10400 MaxSpareThreads 14200 ThreadLimit 5 ThreadsPerChild 5 MaxClients 20000 MaxRequestsPerChild 0 </IfModule> The VPS have the SO: Debian 64 LAMP, memory: 14gb and CPU: 24ghz What I could to do to give a best performance?

  Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >