Search Results

Search found 11365 results on 455 pages for 'authorization basic'.

Page 422/455 | < Previous Page | 418 419 420 421 422 423 424 425 426 427 428 429  | Next Page >

• Cisco VPN Client dropping connection

  - by IT Team

  Using Windows XP and Cisco VPN client version 5.0.4.xxx to connect to a remote customer site. We are able to establish the connection and start an RDP session, but within 1-2 minutes the connection drops and the VPN connection disconnects. The PC making the connection is on a DMZ which is NATed to a public IP address. If we move the PC directly onto the internet without being on the DMZ the connection works and we don't encounter any disconnects. We use a PIX 515E running 7.2.4 and don't have any problems with similar setups connecting to other customer sites from the DMZ. The VPN setup on the client side is pretty basic, using IPSec over TCP port 10000. Not sure what device they are using on the peer, but my guess would be an ASA. Any idea as to what the problem would be? Below is the logs from the VPN client when the problem occurs. The real IP address has been changed to: RemotePeerIP. 4 14:39:30.593 09/23/09 Sev=Info/4 CM/0x63100024 Attempt connection with server "RemotePeerIP" 5 14:39:30.593 09/23/09 Sev=Info/6 CM/0x6310002F Allocated local TCP port 1942 for TCP connection. 6 14:39:30.796 09/23/09 Sev=Info/4 IPSEC/0x63700008 IPSec driver successfully started 7 14:39:30.796 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 8 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x6370002C Sent 256 packets, 0 were fragmented. 9 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x63700020 TCP SYN sent to RemotePeerIP, src port 1942, dst port 10000 10 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x6370001C TCP SYN-ACK received from RemotePeerIP, src port 10000, dst port 1942 11 14:39:30.796 09/23/09 Sev=Info/6 IPSEC/0x63700021 TCP ACK sent to RemotePeerIP, src port 1942, dst port 10000 12 14:39:30.796 09/23/09 Sev=Warning/3 IPSEC/0xA370001C Bad cTCP trailer, Rsvd 26984, Magic# 63697672h, trailer len 101, MajorVer 13, MinorVer 10 13 14:39:30.796 09/23/09 Sev=Info/4 CM/0x63100029 TCP connection established on port 10000 with server "RemotePeerIP" 14 14:39:31.296 09/23/09 Sev=Info/4 CM/0x63100024 Attempt connection with server "RemotePeerIP" 15 14:39:31.296 09/23/09 Sev=Info/6 IKE/0x6300003B Attempting to establish a connection with RemotePeerIP. 16 14:39:31.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Unity)) to RemotePeerIP 17 14:39:36.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 18 14:39:36.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 19 14:39:41.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 20 14:39:41.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 21 14:39:46.296 09/23/09 Sev=Info/4 IKE/0x63000021 Retransmitting last packet! 22 14:39:46.296 09/23/09 Sev=Info/4 IKE/0x63000013 SENDING ISAKMP OAK AG (Retransmission) to RemotePeerIP 23 14:39:51.328 09/23/09 Sev=Info/4 IKE/0x63000017 Marking IKE SA for deletion (I_Cookie=AEFC3FFF0405BBD6 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING 24 14:39:51.828 09/23/09 Sev=Info/4 IKE/0x6300004B Discarding IKE SA negotiation (I_Cookie=AEFC3FFF0405BBD6 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING 25 14:39:51.828 09/23/09 Sev=Info/4 CM/0x63100014 Unable to establish Phase 1 SA with server "RemotePeerIP" because of "DEL_REASON_PEER_NOT_RESPONDING" 26 14:39:51.828 09/23/09 Sev=Info/5 CM/0x63100025 Initializing CVPNDrv 27 14:39:51.828 09/23/09 Sev=Info/4 CM/0x6310002D Resetting TCP connection on port 10000 28 14:39:51.828 09/23/09 Sev=Info/6 CM/0x63100030 Removed local TCP port 1942 for TCP connection. 29 14:39:51.828 09/23/09 Sev=Info/6 CM/0x63100046 Set tunnel established flag in registry to 0. 30 14:39:51.828 09/23/09 Sev=Info/4 IKE/0x63000001 IKE received signal to terminate VPN connection 31 14:39:52.328 09/23/09 Sev=Info/6 IPSEC/0x63700023 TCP RST sent to RemotePeerIP, src port 1942, dst port 10000 32 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 33 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 34 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 35 14:39:52.328 09/23/09 Sev=Info/4 IPSEC/0x6370000A IPSec driver successfully stopped Thank you for any help you can provide.

  Read the article

• Weird networking problem ( Linksys, Windows 7 )

  - by Rohit Nair

  Okay it's a bit tough to figure out where to start from, but here is the basic summary of the issue: During general internet usage, there are times when any attempt to visit a website stalls at "Waiting for somedomain.com". This problem occurs in Firefox, IE and Chrome. No website will load, INCLUDING the router configuration page at 192.168.1.1. Curiously, ping works fine, and other network apps such as MSN Messenger continue to work and I can send and receive messages. Disconnecting and reconnecting to the wireless network seems to fix the problem for a bit, but there are times when it relapses into not loading after every 2-3 http requests. Restarting the router seems to fix the issue, but it can crop up hours or days later. I have a CCNA cert and I know my way around the Windows family of operating systems, so I'm going to list all the things I've tried here. Other computers on the network seem to suffer the same problem, which makes me think it might be a specific problem with something in Win7. The random nature of this issue makes it a bit difficult to confirm, but I can definitely say that I have experienced this on the following systems: Windows 7 64-bit on my desktop Windows Vista 32-bit on my desktop ( the desktop has 2 wireless NICs and the problem existed on both ) Windows Vista 32-bit on my laptop ( both with wireless and wired ) Windows XP SP3 on another laptop ( both wireless and wired ) Using Wireshark to sniff packets seemed to indicate that although HTTP requests were being SENT out, no packets were coming in to respond to the HTTP request. However, other network apps continued to work i.e I would still receive IMs on Windows Live Messenger. Disabling IPV6 had no effect. Updating router firmware to the latest stock firmware by Linksys had no effect. Switching to dd-wrt firmware had no effect. By "no effect" I mean that although the restart required by firmware updates fixed the problem at the time, it still came back. A couple of weeks back, after a LOT of googling and flipping of various options, I figured it might be a case of router slowdown ( http://www.dd-wrt.com/wiki/index.php/Router%5FSlowdown ) caused by the fact that I occasionally run a torrent client. I tried changing the configuration as suggested in that router slowdown link, and restarted the router. However I have not run the torrent client for 12 days now, and yet I still randomly experience this problem. Currently the computer I am using is running Windows 7 64-bit. I would just like to reiterate some of the reasons that I was confused by the issue. Even the router config page at 192.168.1.1 would not load, indicating that it's not a problem with the WAN link, but probably a router issue or a local computer issue. For some reason, disconnecting and reconnecting to the wireless network immediately seems to fix the problem. Updating the router firmware, even switching to open source firmware did nothing. So it seemed to be a computer issue. On the other hand, I have not seen any mass outrage of people having networking problems with Windows 7 and Linksys routers, especially a problem of this sort, and I have tweaked every network setting I could think of. Although HTTP seems to have trouble, ping works fine, DNS lookups work fine, other networking apps work fine. However if I disconnect from Windows Live Messenger and try to reconnect, it fails to reconnect. So although it could receive data over the existing TCP/IP connection, trying to start a new one failed? Does anyone have any further ideas on debugging or fixing this issue? I am reasonably certain there are no viruses or other malicious apps on my network, and I am also reasonably certain that nobody is accessing my router without my consent. Router: Linksys WRT54G2 1.0 running dd-wrt firmware Wireless Card: Alfa AWUS036H OS: Windows 7 64-bit EDIT: I tried switching to a clean wireless channel free from interference, but the problem still persisted. I tried connecting directly with a cable, but the problem still persisted. Signed A very confused and bewildered geek whose knowledge seems to be useless in the face of this frustrating network issue.

  Read the article

• Pig_Cassandra integration caused - ERROR 1070: Could not resolve CassandraStorage using imports:

  - by Le Dude

  I'm following basic Pig, Cassandra, Hadoop installation. Everything works just fine as a stand alone. No error. However when I tried to run the example file provided by Pig_cassandra example, I got this error. [root@localhost pig]# /opt/cassandra/apache-cassandra-1.1.6/examples/pig/bin/pig_cassandra -x local -x local /opt/cassandra/apache-cassandra-1.1.6/examples/pig/example-script.pig Using /opt/pig/pig-0.10.0/pig-0.10.0-withouthadoop.jar. 2012-10-24 21:14:58,551 [main] INFO org.apache.pig.Main - Apache Pig version 0.10.0 (r1328203) compiled Apr 19 2012, 22:54:12 2012-10-24 21:14:58,552 [main] INFO org.apache.pig.Main - Logging error messages to: /opt/pig/pig_1351138498539.log 2012-10-24 21:14:59,004 [main] INFO org.apache.pig.backend.hadoop.executionengine.HExecutionEngine - Connecting to hadoop file system at: file:/// 2012-10-24 21:14:59,472 [main] ERROR org.apache.pig.tools.grunt.Grunt - ERROR 1070: Could not resolve CassandraStorage using imports: [, org.apache.pig.builtin., org.apache.pig.impl.builtin.] Details at logfile: /opt/pig/pig_1351138498539.log Here is the log file Pig Stack Trace --------------- ERROR 1070: Could not resolve CassandraStorage using imports: [, org.apache.pig.builtin., org.apache.pig.impl.builtin.] org.apache.pig.impl.logicalLayer.FrontendException: ERROR 1000: Error during parsing. Could not resolve CassandraStorage using imports: [, org.apache.pig.builtin., org.apache.pig.impl.builtin.] at org.apache.pig.PigServer$Graph.parseQuery(PigServer.java:1597) at org.apache.pig.PigServer$Graph.registerQuery(PigServer.java:1540) at org.apache.pig.PigServer.registerQuery(PigServer.java:540) at org.apache.pig.tools.grunt.GruntParser.processPig(GruntParser.java:970) at org.apache.pig.tools.pigscript.parser.PigScriptParser.parse(PigScriptParser.java:386) at org.apache.pig.tools.grunt.GruntParser.parseStopOnError(GruntParser.java:189) at org.apache.pig.tools.grunt.GruntParser.parseStopOnError(GruntParser.java:165) at org.apache.pig.tools.grunt.Grunt.exec(Grunt.java:84) at org.apache.pig.Main.run(Main.java:555) at org.apache.pig.Main.main(Main.java:111) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.hadoop.util.RunJar.main(RunJar.java:156) Caused by: Failed to parse: Cannot instantiate: CassandraStorage at org.apache.pig.parser.QueryParserDriver.parse(QueryParserDriver.java:184) at org.apache.pig.PigServer$Graph.parseQuery(PigServer.java:1589) ... 14 more Caused by: java.lang.RuntimeException: Cannot instantiate: CassandraStorage at org.apache.pig.impl.PigContext.instantiateFuncFromSpec(PigContext.java:510) at org.apache.pig.parser.LogicalPlanBuilder.validateFuncSpec(LogicalPlanBuilder.java:791) at org.apache.pig.parser.LogicalPlanBuilder.buildFuncSpec(LogicalPlanBuilder.java:780) at org.apache.pig.parser.LogicalPlanGenerator.func_clause(LogicalPlanGenerator.java:4583) at org.apache.pig.parser.LogicalPlanGenerator.load_clause(LogicalPlanGenerator.java:3115) at org.apache.pig.parser.LogicalPlanGenerator.op_clause(LogicalPlanGenerator.java:1291) at org.apache.pig.parser.LogicalPlanGenerator.general_statement(LogicalPlanGenerator.java:789) at org.apache.pig.parser.LogicalPlanGenerator.statement(LogicalPlanGenerator.java:507) at org.apache.pig.parser.LogicalPlanGenerator.query(LogicalPlanGenerator.java:382) at org.apache.pig.parser.QueryParserDriver.parse(QueryParserDriver.java:175) ... 15 more Caused by: org.apache.pig.backend.executionengine.ExecException: ERROR 1070: Could not resolve CassandraStorage using imports: [, org.apache.pig.builtin., org.apache.pig.impl.builtin.] at org.apache.pig.impl.PigContext.resolveClassName(PigContext.java:495) at org.apache.pig.impl.PigContext.instantiateFuncFromSpec(PigContext.java:507) ... 24 more ================================================================================ I googled around and got to this point from other stackoverflow user that identified the potential problem but not the solution. Cassandra and pig integration cause error during startup I believe my configuration is correct and the path has already been defined properly. I didn't change anything in the pig_cassandra file. I'm not quite sure how to proceed from here. Please help?

  Read the article

• Ubuntu: Failure to login with multiple video adapters

  - by tsilb

  Forgive my ignorance, for I am a complete linux noob. I have a computer with three video cards and six monitors. Works great on Windows. Trying to get it to run Ubuntu as well. It loads fine when I have it configured to run on one adapter; detects both screens, runs ok. But I want to turn the other 4 monitors on and run the whole thing as one extended desktop (one session, etc). So I downloaded and installed the newest ATI driver for Linux, which seems to work, kinda. I ran this to set up the screens: aticonfig --adapter=all --initial -f Now when I boot, Ubuntu seems to turn on all the screens (3 viewports, each with two cloned displays from what I can tell). When I enter my login info OR move the mouse off the main screen, the screens freeze and the kbd/ms become unresponsive. aticonfig generated xorg.conf included below. Have tried the following: aticonfig -initial -f - works, but only detects the primary adapter and 2 screens aticccle - Tells me I have to reboot after enabling the other cards. Then goes into above described freezing state. aticonfig --adapter=all --initial -f - see above Manually editing xorg.conf file with my limited knowledge - Was able to get two adapters running, but only the second adapter initialized while the primary stopped at the Ubuntu boot screen. Was unable to see the login prompt. Froze after I logged in blindly (was able to hear the login sound). Using generic "radeon" driver instead of ATI Proprietary driver with the above init attempts Toggling xinerama Various combinations of the above Hardware: Intel Core 2 Quad q6600 8GB DDR2 (3x) ATI Radeon HD 4680 5 monitors (21W, 21W, 22W Portrait, 22W Portrait, 19")and an HDTV (26"W, HDMI) in a horizontal arrangement I know next to nothing about Linux/Ubuntu aside from basic filesystem navigation, editing text files, and accessing my local and networked Windows stores and shares. Basically this is the most advanced thing I've had to do. I installed today. Please advise how to make this configuration work. my xorg.conf: Section "ServerLayout" Identifier "Layout0" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[2]-0" RightOf "aticonfig-Screen[1]-0" Option "RenderAccel" "true" Option "AllowGLXWithComposite" "true" EndSection Section "Files" EndSection Section "Module" EndSection Section "ServerFlags" Option "Xinerama" "0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[2]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[2]-0" Driver "fglrx" BusID "PCI:4:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[2]-0" Device "aticonfig-Device[2]-0" Monitor "aticonfig-Monitor[2]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• mono 3.0.2 + xsp + lighttpd delivers empty page

  - by Nefal Warnets

  I needed MVC 4 (and basic .NET 4.5) support so I downloaded mono 3.0.2 and deployed it on an lighttpd 1.4.28 installation, together with xsp-2.10.2 (was the latest I could find). After going through the config tutorials I managed to get the fastcgi server to spawn, but all pages are served empty. even if I go to nonexistant urls or direct .aspx files I get an empty HTTP 200 response. The log file on Debug shows nothing suspicious. Here is the log: [2012-12-12 15:15:38Z] Debug Accepting an incoming connection. [2012-12-12 15:15:38Z] Debug Record received. (Type: BeginRequest, ID: 1, Length: 8) [2012-12-12 15:15:38Z] Debug Record received. (Type: Params, ID: 1, Length: 801) [2012-12-12 15:15:38Z] Debug Record received. (Type: Params, ID: 1, Length: 0) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_SOFTWARE = lighttpd/1.4.28) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_NAME = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (GATEWAY_INTERFACE = CGI/1.1) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_PORT = 80) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_ADDR = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (REMOTE_PORT = xxx) [2012-12-12 15:15:38Z] Debug Read parameter. (REMOTE_ADDR = xxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (SCRIPT_NAME = /ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (PATH_INFO = ) [2012-12-12 15:15:38Z] Debug Read parameter. (SCRIPT_FILENAME = /data/htdocs/ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (DOCUMENT_ROOT = /data/htdocs) [2012-12-12 15:15:38Z] Debug Read parameter. (REQUEST_URI = /ViewPage1.aspx) [2012-12-12 15:15:38Z] Debug Read parameter. (QUERY_STRING = ) [2012-12-12 15:15:38Z] Debug Read parameter. (REQUEST_METHOD = GET) [2012-12-12 15:15:38Z] Debug Read parameter. (REDIRECT_STATUS = 200) [2012-12-12 15:15:38Z] Debug Read parameter. (SERVER_PROTOCOL = HTTP/1.1) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_HOST = xxxxx) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_CONNECTION = keep-alive) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_CACHE_CONTROL = max-age=0) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_USER_AGENT = Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT = text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_ENCODING = gzip,deflate,sdch) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_LANGUAGE = en-US,en;q=0.8) [2012-12-12 15:15:38Z] Debug Read parameter. (HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.3) [2012-12-12 15:15:38Z] Debug Record received. (Type: StandardInput, ID: 1, Length: 0) [2012-12-12 15:15:38Z] Debug Record sent. (Type: EndRequest, ID: 1, Length: 8) lighttpd config: server.modules += ( "mod_fastcgi" ) include "conf.d/mono.conf" $HTTP["host"] !~ "^vdn\." { $HTTP["url"] !~ "\.(jpg|gif|png|js|css|swf|ico|jpeg|mp4|flv|zip|7z|rar|psd|pdf|html|htm)$" { fastcgi.server += ( "" => (( "socket" => mono_shared_dir + "fastcgi-mono-server", "bin-path" => mono_fastcgi_server, "bin-environment" => ( "PATH" => mono_dir + "bin:/bin:/usr/bin:", "LD_LIBRARY_PATH" => mono_dir + "lib:", "MONO_SHARED_DIR" => mono_shared_dir, "MONO_FCGI_LOGLEVELS" => "Debug", "MONO_FCGI_LOGFILE" => mono_shared_dir + "fastcgi.log", "MONO_FCGI_ROOT" => mono_fcgi_root, "MONO_FCGI_APPLICATIONS" => mono_fcgi_applications ), "max-procs" => 1, "check-local" => "disable" )) ) } } the referenced mono.conf index-file.names += ( "index.aspx", "default.aspx" ) var.mono_dir = "/usr/" var.mono_shared_dir = "/tmp/" var.mono_fastcgi_server = mono_dir + "bin/" + "fastcgi-mono-server4" var.mono_fcgi_root = server.document-root var.mono_fcgi_applications = "/:." The document root for this server is /data/htdocs. The asp.net files reside there. lighttpd error logs show nothing. Every help is greatly appreciated!

  Read the article

• Monit won't run

  - by Yaniro

  I have two identical EC2 instances (the second is a replica of the first), running Gentoo. The first instance has monit running which monitors a single process and some system resources and functions great. In the second instance, monit runs but quits right away. The configuration is similar on both instances so are the versions of monit. monit.log shows: [GMT Oct 3 08:36:41] info : monit daemon with PID 5 awakened Final lines on strace monit show: write(2, "monit daemon with PID 5 awakened"..., 33monit daemon with PID 5 awakened ) = 33 time(NULL) = 1349252827 open("/etc/localtime", O_RDONLY) = 4 fstat64(4, {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 fstat64(4, {st_mode=S_IFREG|0644, st_size=118, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb773a000 read(4, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\1\0\0\0\1\0\0\0\0"..., 4096) = 118 _llseek(4, -6, [112], SEEK_CUR) = 0 read(4, "\nGMT0\n", 4096) = 6 close(4) = 0 munmap(0xb773a000, 4096) = 0 write(3, "[GMT Oct 3 08:27:07] info :"..., 33) = 33 write(3, "monit daemon with PID 5 awakened"..., 33) = 33 waitpid(-1, NULL, WNOHANG) = -1 ECHILD (No child processes) close(3) = 0 exit_group(0) = ? No core dumps (ulimit -c shows unlimited) monit -v shows: monit: Debug: Adding host allow 'localhost' monit: Debug: Skipping redundant host 'localhost' monit: Debug: Skipping redundant host 'localhost' monit: Debug: Adding credentials for user 'xxxx'. Runtime constants: Control file = /etc/monitrc Log file = /var/log/monit/monit.log Pid file = /var/run/monit.pid Id file = /var/run/monit.pid Debug = True Log = True Use syslog = False Is Daemon = True Use process engine = True Poll time = 30 seconds with start delay 0 seconds Expect buffer = 256 bytes Event queue = base directory /var/monit with 100 slots Mail server(s) = xx.xxx.xx.xxx with timeout 30 seconds Mail from = (not defined) Mail subject = (not defined) Mail message = (not defined) Start monit httpd = True httpd bind address = Any/All httpd portnumber = 2812 httpd signature = True Use ssl encryption = False httpd auth. style = Basic Authentication and Host/Net allow list Alert mail to = [email protected] Alert on = All events The service list contains the following entries: System Name = xxxx Monitoring mode = active CPU wait limit = if greater than 20.0% 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert CPU system limit = if greater than 30.0% 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert CPU user limit = if greater than 70.0% 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert Swap usage limit = if greater than 25.0% 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert Memory usage limit = if greater than 75.0% 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert Load avg. (5min) = if greater than 2.0 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert Load avg. (1min) = if greater than 4.0 1 times within 1 cycle(s) then alert else if succeeded 1 times within 1 cycle(s) then alert Process Name = xxxx Group = server Pid file = /var/run/xxxx.pid Monitoring mode = active Start program = '/etc/init.d/xxxx restart' timeout 20 second(s) Stop program = '/etc/init.d/xxxx stop' timeout 30 second(s) Existence = if does not exist 1 times within 1 cycle(s) then restart else if succeeded 1 times within 1 cycle(s) then alert Pid = if changed 1 times within 1 cycle(s) then alert Ppid = if changed 1 times within 1 cycle(s) then alert Timeout = If restarted 3 times within 5 cycle(s) then unmonitor Alert mail to = [email protected] Alert on = All events Alert mail to = [email protected] Alert on = All events ------------------------------------------------------------------------------- monit daemon with PID 5 awakened Ran emerge --sync before emerge -va monit which installed monit v5.3.2. When that didn't work i've downloaded v5.5 from their website and compiled from source which did not work either.

  Read the article

• Increase samba space on open suse 12.1

  - by Kapil Sharma

  I know linux basics but not an expert. IT guy left the job here and there is some time before new hire. So sorry if question is very basic. We have local testing server based on Open SUSE 12.1, which also act as shared drive between dev/mgmt team here and using Samba for that. Now we are running out of space on samba, even though server's 2*1TB harddisk is nearly 90% free. My question is, what is limiting Samba and how can I increase its limit? We need around at least 500 GB as shared drive but currently its just 25 GB. I don't need step by step answer, just a link to any helpful article would be sufficient. Probably I'm putting wrong keywords in google so not getting any helpful link. EDIT: Output of commands in the first comment. All commands were run as root user df -h (getting error with df -ht) Filesystem Size Used Avail Use% Mounted on rootfs 30G 5.1G 23G 19% / devtmpfs 2.0G 36K 2.0G 1% /dev tmpfs 2.0G 1.1M 2.0G 1% /dev/shm tmpfs 2.0G 676K 2.0G 1% /run /dev/sda2 30G 5.1G 23G 19% / tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup tmpfs 2.0G 676K 2.0G 1% /var/run tmpfs 2.0G 0 2.0G 0% /media tmpfs 2.0G 676K 2.0G 1% /var/lock /dev/sda3 36G 31G 3.3G 91% /home fdisk -l /dev/[hmsv]d* Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2d4a2d49 Device Boot Start End Blocks Id System /dev/sda1 2048 16771071 8384512 82 Linux swap / Solaris /dev/sda2 * 16771072 79681535 31455232 83 Linux /dev/sda3 79681536 156301311 38309888 83 Linux Disk /dev/sda1: 8585 MB, 8585740288 bytes 255 heads, 63 sectors/track, 1043 cylinders, total 16769024 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 32.2 GB, 32210157568 bytes 255 heads, 63 sectors/track, 3915 cylinders, total 62910464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System Disk /dev/sda3: 39.2 GB, 39229325312 bytes 255 heads, 63 sectors/track, 4769 cylinders, total 76619776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda3 doesn't contain a valid partition table vgs No volume groups found lvs No volume groups found output of vi /etc/samba/smb.conf # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. # Date: 2011-11-02 [global] workgroup = WORKGROUP passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User include = /etc/samba/dhcp.conf logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 [allusers] comment = All Users path = /home/shares/allusers valid users = @users force group = users create mask = 0660 directory mask = 0771 writable = yes

  Read the article

• Diagnosing packet loss / high latency in Ubuntu

  - by Sam Gammon

  We have a Linux box (Ubuntu 12.04) running Nginx (1.5.2), which acts as a reverse proxy/load balancer to some Tornado and Apache hosts. The upstream servers are physically and logically close (same DC, sometimes same-rack) and show sub-millisecond latency between them: PING appserver (10.xx.xx.112) 56(84) bytes of data. 64 bytes from appserver (10.xx.xx.112): icmp_req=1 ttl=64 time=0.180 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=2 ttl=64 time=0.165 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=3 ttl=64 time=0.153 ms We receive a sustained load of about 500 requests per second, and are currently seeing regular packet loss / latency spikes from the Internet, even from basic pings: sam@AM-KEEN ~> ping -c 1000 loadbalancer PING 50.xx.xx.16 (50.xx.xx.16): 56 data bytes 64 bytes from loadbalancer: icmp_seq=0 ttl=56 time=11.624 ms 64 bytes from loadbalancer: icmp_seq=1 ttl=56 time=10.494 ms ... many packets later ... Request timeout for icmp_seq 2 64 bytes from loadbalancer: icmp_seq=2 ttl=56 time=1536.516 ms 64 bytes from loadbalancer: icmp_seq=3 ttl=56 time=536.907 ms 64 bytes from loadbalancer: icmp_seq=4 ttl=56 time=9.389 ms ... many packets later ... Request timeout for icmp_seq 919 64 bytes from loadbalancer: icmp_seq=918 ttl=56 time=2932.571 ms 64 bytes from loadbalancer: icmp_seq=919 ttl=56 time=1932.174 ms 64 bytes from loadbalancer: icmp_seq=920 ttl=56 time=932.018 ms 64 bytes from loadbalancer: icmp_seq=921 ttl=56 time=6.157 ms --- 50.xx.xx.16 ping statistics --- 1000 packets transmitted, 997 packets received, 0.3% packet loss round-trip min/avg/max/stddev = 5.119/52.712/2932.571/224.629 ms The pattern is always the same: things operate fine for a while (<20ms), then a ping drops completely, then three or four high-latency pings (1000ms), then it settles down again. Traffic comes in through a bonded public interface (we will call it bond0) configured as such: bond0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5d inet addr:50.xx.xx.16 Bcast:50.xx.xx.31 Mask:255.255.255.224 inet6 addr: <ipv6 address> Scope:Global inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:527181270 errors:1 dropped:4 overruns:0 frame:1 TX packets:413335045 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240016223540 (240.0 GB) TX bytes:104301759647 (104.3 GB) Requests are then submitted via HTTP to upstream servers on the private network (we can call it bond1), which is configured like so: bond1 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5c inet addr:10.xx.xx.70 Bcast:10.xx.xx.127 Mask:255.255.255.192 inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:430293342 errors:1 dropped:2 overruns:0 frame:1 TX packets:466983986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:77714410892 (77.7 GB) TX bytes:227349392334 (227.3 GB) Output of uname -a: Linux <hostname> 3.5.0-42-generic #65~precise1-Ubuntu SMP Wed Oct 2 20:57:18 UTC 2013 x86_64 GNU/Linux We have customized sysctl.conf in an attempt to fix the problem, with no success. Output of /etc/sysctl.conf (with irrelevant configs omitted): # net: core net.core.netdev_max_backlog = 10000 # net: ipv4 stack net.ipv4.tcp_ecn = 2 net.ipv4.tcp_sack = 1 net.ipv4.tcp_fack = 1 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_max_syn_backlog = 10000 net.ipv4.tcp_congestion_control = cubic net.ipv4.ip_local_port_range = 8000 65535 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_thin_dupack = 1 net.ipv4.tcp_thin_linear_timeouts = 1 net.netfilter.nf_conntrack_max = 99999999 net.netfilter.nf_conntrack_tcp_timeout_established = 300 Output of dmesg -d, with non-ICMP UFW messages suppressed: [508315.349295 < 19.852453>] [UFW BLOCK] IN=bond1 OUT= MAC=<mac addresses> SRC=118.xx.xx.143 DST=50.xx.xx.16 LEN=68 TOS=0x00 PREC=0x00 TTL=51 ID=43221 PROTO=ICMP TYPE=3 CODE=1 [SRC=50.xx.xx.16 DST=118.xx.xx.143 LEN=40 TOS=0x00 PREC=0x00 TTL=249 ID=10220 DF PROTO=TCP SPT=80 DPT=53817 WINDOW=8190 RES=0x00 ACK FIN URGP=0 ] [517787.732242 < 0.443127>] Peer 190.xx.xx.131:59705/80 unexpectedly shrunk window 1155488866:1155489425 (repaired) How can I go about diagnosing the cause of this problem, on a Debian-family Linux box?

  Read the article

• proftpd, dynamic IP, and filezilla: port troubles

  - by Yami

  The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

  Read the article

• High Load mysql on Debian server

  - by Oleg Abrazhaev

  I have Debian server with 32 gb memory. And there is apache2, memcached and nginx on this server. Memory load always on maximum. Only 500m free. Most memory leak do MySql. Apache only 70 clients configured, other services small memory usage. When mysql use all memory it stops. And nothing works, need mysql reboot. Mysql configured use maximum 24 gb memory. I have hight weight InnoDB bases. (400000 rows, 30 gb). And on server multithread daemon, that makes many inserts in this tables, thats why InnoDB. There is my mysql config. [mysqld] # # * Basic Settings # default-time-zone = "+04:00" user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking default-time-zone='Europe/Moscow' # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. # # * Fine Tuning # #low_priority_updates = 1 concurrent_insert = ALWAYS wait_timeout = 600 interactive_timeout = 600 #normal key_buffer_size = 2024M #key_buffer_size = 1512M #70% hot cache key_cache_division_limit= 70 #16-32 max_allowed_packet = 32M #1-16M thread_stack = 8M #40-50 thread_cache_size = 50 #orderby groupby sort sort_buffer_size = 64M #same myisam_sort_buffer_size = 400M #temp table creates when group_by tmp_table_size = 3000M #tables in memory max_heap_table_size = 3000M #on disk open_files_limit = 10000 table_cache = 10000 join_buffer_size = 5M # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #myisam_use_mmap = 1 max_connections = 200 thread_concurrency = 8 # # * Query Cache Configuration # #more ignored query_cache_limit = 50M query_cache_size = 210M #on query cache query_cache_type = 1 # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. #log = /var/log/mysql/mysql.log # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log server-id = 1 log-bin = /var/lib/mysql/mysql-bin #replicate-do-db = gate log-bin-index = /var/lib/mysql/mysql-bin.index log-error = /var/lib/mysql/mysql-bin.err relay-log = /var/lib/mysql/relay-bin relay-log-info-file = /var/lib/mysql/relay-bin.info relay-log-index = /var/lib/mysql/relay-bin.index binlog_do_db = 24avia expire_logs_days = 10 max_binlog_size = 100M read_buffer_size = 4024288 innodb_buffer_pool_size = 5000M innodb_flush_log_at_trx_commit = 2 innodb_thread_concurrency = 8 table_definition_cache = 2000 group_concat_max_len = 16M #binlog_do_db = gate #binlog_ignore_db = include_database_name # # * BerkeleyDB # # Using BerkeleyDB is now discouraged as its support will cease in 5.1.12. #skip-bdb # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # You might want to disable InnoDB to shrink the mysqld process by circa 100MB. #skip-innodb # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 500M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M key_buffer_size = 512M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ Please, help me make it stable. Memory used /etc/mysql # free total used free shared buffers cached Mem: 32930800 32766424 164376 0 139208 23829196 -/+ buffers/cache: 8798020 24132780 Swap: 33553328 44660 33508668 Maybe my problem not in memory, but MySQL stops every day. As you can see, cache memory free 24 gb. Thank to Michael Hampton? for correction. Load overage on server 3.5. Maybe hdd or another problem? Maybe my config not optimal for 30gb InnoDB ?

  Read the article

• ERROR 2003 (HY000): Can't connect to MySQL server on (111)

  - by JohnMerlino

  I am unable to connect to on my ubuntu installation a remote tcp/ip which contains a mysql installation: viggy@ubuntu:~$ mysql -u user.name -p -h xxx.xxx.xxx.xxx -P 3306 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.xxx.xxx.xxx' (111) I commented out the line below using vim in /etc/mysql/my.cnf: # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 Then I restarted the server: sudo service mysql restart But still I get the same error. This is the content of my.cnf: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ (Note that I can log into my local mysql install just fine by running mysql (and it will log me in as root) and also note that I can get into mysql in the remote server by logging into via ssh and then invoking mysql), but I am unable to connect to the remote server via my terminal using the host, and I need to do it that way so that I can then use mysql workbench.

  Read the article

• Initial Cisco ASA 5510 Config

  - by Brendan ODonnell

  Fair warning, I'm a but of a noob so please bear with me. I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. I'd appreciate any help I can get. Here's the sh run. : Saved : ASA Version 8.4(3) ! hostname gateway domain-name xxx.local enable password xxx encrypted passwd xxx encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/1 nameif inside security-level 100 ip address 10.x.x.x 255.255.255.0 ! interface Ethernet0/2 shutdown no nameif no security-level no ip address ! interface Ethernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! ftp mode passive dns domain-lookup inside dns server-group DefaultDNS name-server 10.x.x.x domain-name xxx.local same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-network subnet 10.x.x.x 255.255.255.0 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list outside_access_in extended permit ip any any access-list inside_access_in extended permit ip any any pager lines 24 logging enable logging buffered informational logging asdm informational mtu management 1500 mtu inside 1500 mtu outside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside icmp permit any outside no asdm history enable arp timeout 14400 ! object network inside-network nat (any,outside) dynamic interface access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL aaa authentication http console LOCAL http server enable http 192.168.1.0 255.255.255.0 management http 10.x.x.x 255.255.255.0 inside http authentication-certificate management http authentication-certificate inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart telnet timeout 5 ssh 192.168.1.0 255.255.255.0 management ssh 10.x.x.x 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 dhcp-client client-id interface outside dhcpd address 192.168.1.2-192.168.1.254 management dhcpd enable management ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn username xxx password xxx encrypted ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options inspect icmp ! service-policy global_policy global prompt hostname context no call-home reporting anonymous Cryptochecksum:fe19874e18fe7107948eb0ada6240bc2 : end no asdm history enable

  Read the article

• Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

  - by franklundy

  Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

  Read the article

• Coda 2 and SCP uploading files with the wrong permission

  - by Tom Black

  Currently I have a basic Ubuntu server running a website. The website is for a few students learning HTML/PHP and each student has their own account with a symbolic link to the shared website folder. Since the students are working on the website together, each user needs to be able to modify all the files (index.html for example). So I created a Webdev group containing all of the students with the default umask of 0002 set in their .bashrc (This allows newly created files to be 774). The shared folder is owned by the group Webdev with a chmod g+s so that new files/folders also belong to the group Webdev. The problem is that the students are using an IDE (Coda 2) and when they create a new file or folder using the IDE the file has the permissions of 644 on the server (not group writable). However when I make a new file through connecting with Cyberduck (SFTP client) the file permissions are 664 (as they should be). So I don't understand why Coda would be any different. However, after some trial and error I believe that Coda is first creating the file on local disk and then uploading that file to the server. On a mac by default a newly created file is 644. When the client uploads a file that's already 644 it stays 644 on the server side (umask is kind of useless in this situation). I've also tried creating ACL permissions for that folder but an uploaded file from my mac via SCP doesn't get the default ACL permissions. In Coda there is an option to change file permissions on a transfer. However this option seems to apply a chmod to all files being uploaded or saved. When one of students is modifying a file created by someone else when they try to upload the file or save it Coda tries to also do a chmod but fails because that user isn't the owner of the file. My current solution is using bindfs... I mount the shared web folder and bindfs sets permissions and group ownership of newly created files. However, bindfs seems to be a bit slow and I'm sure there is a better solution. Even if the students ditched Coda 2 and used Mac vim with scp the newly created files on the server would behave the same (644) which is default on the mac. Other options... 1) Either I teach the students to use (ssh/chmod) with their IDE to change their own file permissions when uploading. 2) I make all the students' Macs have the default umask of 0002 which would upload files with the right permissions. 3) Write a corn script to fix the file permissions every 5 to 15 minutes... (This option I think is the worst if students are working together at the same time). Is there any way that I could make all files that are uploaded via SCP have the default file permissions of 664 even though the uploaded file has a lower permission? (After hours of searching I don't think this is possible) I guess a corn script is my best option for novice users. How do web developers work together on larger sites? similar to this: http://serverfault.com/questions/283492/how-to-specify-file-permission-when-putting-a-file-using-openssh-sftp-command Also similar: http://serverfault.com/questions/395418/managing-linux-directory-permissions-sftp

  Read the article

• How do I get my ubuntu server to listen for database connections?

  - by Bob Flemming

  I am having a problems connecting to my database outside of phpmyadmin. Im pretty sure this is because my server isn't listening on port 3306. When I type: sudo netstat -ntlp on my OTHER working server I can see the following line: tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 20445/mysqld However, this line does not appear on the server I am having difficulty with. How do I make my sever listen for mysql connections? Here my my.conf file: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql #skip-networking=off #skip_networking=off #skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 0.0.0.0 # # * Fine Tuning # key_buffer = 64M max_allowed_packet = 64M thread_stack = 650K thread_cache_size = 32 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 2M query_cache_size = 32M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 32M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/

  Read the article

• Have I pushed the limits of my current VPS or is there room for optimization?

  - by JRameau

  I am currently on a mediatemple DV server (basic) 512mb dedicated ram, this is a CentOS based VPS with Plesk and Virtuozzo. My experience with it from day 1 has been bad and I only could sooth my server issues with several caching "Band-aids," but my sites are not as small as they were a year ago either so the issues have worsen. I have 3 Drupal installs running on separate (plesk) domains, 1 of those drupal installs is a multisite, that consists of 5-6 sites 2 of those sites are bringing in actual traffic. Those caching "Band-aids" I mentioned are APC, which seemed to help alot initially, and Drupal's Boost, which is considered a poorman's Varnish, it makes all my pages static for anonymous users. Last 30day combined estimate on Google Ananlytics: 90k visitors 260k pageviews. Issue: alot of downtime, I am continually checking if my sites are up, and lately I have been finding it down more than 3 times daily. Restarting Apache will bring it back up, for some time. I have google search every error message and looked up ways to optimize my DV server, and I am beyond stump what is my next move. Is this server bad, have I hit a impossibly low restriction such as the 12mb kernel memory barrier (kmemsize), is it on my end, do I need to optimize some more? *I have provided as much information as I can below, any help or suggestions given will be appreciated Common Error messages I see in the log: [error] (12)Cannot allocate memory: fork: Unable to fork new process [error] make_obcallback: could not import mod_python.apache.\n Traceback (most recent call last): File "/usr/lib/python2.4/site-packages/mod_python/apache.py", line 21, in ? import traceback File "/usr/lib/python2.4/traceback.py", line 3, in ? import linecache ImportError: No module named linecache [error] python_handler: no interpreter callback found. [warn-phpd] mmap cache can't open /var/www/vhosts/***/httpdocs/*** - Too many open files in system (pid ***) [alert] Child 8125 returned a Fatal error... Apache is exiting! [emerg] (43)Identifier removed: couldn't grab the accept mutex [emerg] (22)Invalid argument: couldn't release the accept mutex cat /proc/user_beancounters: Version: 2.5 uid resource held maxheld barrier limit failcnt 41548: kmemsize 4582652 5306699 12288832 13517715 21105036 lockedpages 0 0 600 600 0 privvmpages 38151 42676 229036 249036 0 shmpages 16274 16274 17237 17237 2 dummy 0 0 0 0 0 numproc 43 46 300 300 0 physpages 27260 29528 0 2147483647 0 vmguarpages 0 0 131072 2147483647 0 oomguarpages 27270 29538 131072 2147483647 0 numtcpsock 21 29 300 300 0 numflock 8 8 480 528 0 numpty 1 1 30 30 0 numsiginfo 0 1 1024 1024 0 tcpsndbuf 648440 675272 2867477 4096277 1711499 tcprcvbuf 301620 359716 2867477 4096277 0 othersockbuf 4472 4472 1433738 2662538 0 dgramrcvbuf 0 0 1433738 1433738 0 numothersock 12 12 300 300 0 dcachesize 0 0 2684271 2764800 0 numfile 3447 3496 6300 6300 3872 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 14 14 200 200 0 TOP: (In January the load avg was really high 3-10, I was able to bring it down where it is currently is by giving APC more memory play around with) top - 16:46:07 up 2:13, 1 user, load average: 0.34, 0.20, 0.20 Tasks: 40 total, 2 running, 37 sleeping, 0 stopped, 1 zombie Cpu(s): 0.3% us, 0.1% sy, 0.0% ni, 99.7% id, 0.0% wa, 0.0% hi, 0.0% si Mem: 916144k total, 156668k used, 759476k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached MySQLTuner: (after optimizing every table and repairing any table with overage I got the fragmented count down to 86) [--] Data in MyISAM tables: 285M (Tables: 1105) [!!] Total fragmented tables: 86 [--] Up for: 2h 44m 38s (409K q [41.421 qps], 6K conn, TX: 1B, RX: 174M) [--] Reads / Writes: 79% / 21% [--] Total buffers: 58.0M global + 2.7M per thread (100 max threads) [!!] Query cache prunes per day: 675307 [!!] Temporary tables created on disk: 35% (7K on disk / 20K total)

  Read the article

• Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• Network Restructure Method for Double-NAT network

  - by Adrian

  Due to a series of poor network design decisions (mostly) made many years ago in order to save a few bucks here and there, I have a network that is decidedly sub-optimally architected. I'm looking for suggestions to improve this less-than-pleasant situation. We're a non-profit with a Linux-based IT department and a limited budget. (Note: None of the Windows equipment we have runs does anything that talks to the Internet nor do we have any Windows admins on staff.) Key points: We have a main office and about 12 remote sites that essentially double NAT their subnets with physically-segregated switches. (No VLANing and limited ability to do so with current switches) These locations have a "DMZ" subnet that are NAT'd on an identically assigned 10.0.0/24 subnet at each site. These subnets cannot talk to DMZs at any other location because we don't route them anywhere except between server and adjacent "firewall". Some of these locations have multiple ISP connections (T1, Cable, and/or DSLs) that we manually route using IP Tools in Linux. These firewalls all run on the (10.0.0/24) network and are mostly "pro-sumer" grade firewalls (Linksys, Netgear, etc.) or ISP-provided DSL modems. Connecting these firewalls (via simple unmanaged switches) is one or more servers that must be publically-accessible. Connected to the main office's 10.0.0/24 subnet are servers for email, tele-commuter VPN, remote office VPN server, primary router to the internal 192.168/24 subnets. These have to be access from specific ISP connections based on traffic type and connection source. All our routing is done manually or with OpenVPN route statements Inter-office traffic goes through the OpenVPN service in the main 'Router' server which has it's own NAT'ing involved. Remote sites only have one server installed at each site and cannot afford multiple servers due to budget constraints. These servers are all LTSP servers several 5-20 terminals. The 192.168.2/24 and 192.168.3/24 subnets are mostly but NOT entirely on Cisco 2960 switches that can do VLAN. The remainder are DLink DGS-1248 switches that I am not sure I trust well enough to use with VLANs. There is also some remaining internal concern about VLANs since only the senior networking staff person understands how it works. All regular internet traffic goes through the CentOS 5 router server which in turns NATs the 192.168/24 subnets to the 10.0.0.0/24 subnets according to the manually-configured routing rules that we use to point outbound traffic to the proper internet connection based on '-host' routing statements. I want to simplify this and ready All Of The Things for ESXi virtualization, including these public-facing services. Is there a no- or low-cost solution that would get rid of the Double-NAT and restore a little sanity to this mess so that my future replacement doesn't hunt me down? Basic Diagram for the main office: These are my goals: Public-facing Servers with interfaces on that middle 10.0.0/24 network to be moved in to 192.168.2/24 subnet on ESXi servers. Get rid of the double NAT and get our entire network on one single subnet. My understanding is that this is something we'll need to do under IPv6 anyway, but I think this mess is standing in the way.

  Read the article

• Users loggin to 3Com switches authenticated by radius not getting admin priv and no access available

  - by 3D1L

  Hi, Following the setup that I have for my Cisco devices, I got some basic level of functionality authenticating users that loggin to 3Com switches authenticated against a RADIUS server. Problem is that I can not get the user to obtain admin privileges. I'm using Microsoft's IAS service. According to 3Com documentation when configuring the access policy on IAS the value of 010600000003 have to be used to specify admin access level. That value have to be input in the Dial-in profile section: 010600000003 - indicates admin privileges 010600000002 - manager 010600000001 - monitor 010600000000 - visitor Here is the configuration on the switch: radius scheme system server-type standard primary authentication XXX.XXX.XXX.XXX accounting optional key authentication XXXXXX key accounting XXXXXX domain system scheme radius-scheme system local-user admin service-type ssh telnet terminal level 3 local-user manager service-type ssh telnet terminal level 2 local-user monitor service-type ssh telnet terminal level 1 The configuration is working with the IAS server because I can check user login events with the Eventviewer tool. Here is the output of the DISPLAY RADIUS command at the switch: [4500]disp radius SchemeName =system Index=0 Type=standard Primary Auth IP =XXX.XXX.XXX.XXX Port=1645 State=active Primary Acct IP =127.0.0.1 Port=1646 State=active Second Auth IP =0.0.0.0 Port=1812 State=block Second Acct IP =0.0.0.0 Port=1813 State=block Auth Server Encryption Key= XXXXXX Acct Server Encryption Key= XXXXXX Accounting method = optional TimeOutValue(in second)=3 RetryTimes=3 RealtimeACCT(in minute)=12 Permitted send realtime PKT failed counts =5 Retry sending times of noresponse acct-stop-PKT =500 Quiet-interval(min) =5 Username format =without-domain Data flow unit =Byte Packet unit =1 Total 1 RADIUS scheme(s). 1 listed Here is the output of the DISPLAY DOMAIN and DISPLAY CONNECTION commands after users log into the switch: [4500]display domain 0 Domain = system State = Active RADIUS Scheme = system Access-limit = Disable Domain User Template: Idle-cut = Disable Self-service = Disable Messenger Time = Disable Default Domain Name: system Total 1 domain(s).1 listed. [4500]display connection Index=0 ,Username=admin@system IP=0.0.0.0 Index=2 ,Username=user@system IP=xxx.xxx.xxx.xxx On Unit 1:Total 2 connections matched, 2 listed. Total 2 connections matched, 2 listed. [4500] Here is the DISP RADIUS STATISTICS: [4500] %Apr 2 00:23:39:957 2000 4500 SHELL/5/LOGIN:- 1 - ecajigas(xxx.xxx.xxx.xxx) in un it1 logindisp radius stat state statistic(total=1048): DEAD=1046 AuthProc=0 AuthSucc=0 AcctStart=0 RLTSend=0 RLTWait=2 AcctStop=0 OnLine=2 Stop=0 StateErr=0 Received and Sent packets statistic: Unit 1........................................ Sent PKT total :4 Received PKT total:1 Resend Times Resend total 1 1 2 1 Total 2 RADIUS received packets statistic: Code= 2,Num=1 ,Err=0 Code= 3,Num=0 ,Err=0 Code= 5,Num=0 ,Err=0 Code=11,Num=0 ,Err=0 Running statistic: RADIUS received messages statistic: Normal auth request , Num=1 , Err=0 , Succ=1 EAP auth request , Num=0 , Err=0 , Succ=0 Account request , Num=1 , Err=0 , Succ=1 Account off request , Num=0 , Err=0 , Succ=0 PKT auth timeout , Num=0 , Err=0 , Succ=0 PKT acct_timeout , Num=3 , Err=1 , Succ=2 Realtime Account timer , Num=0 , Err=0 , Succ=0 PKT response , Num=1 , Err=0 , Succ=1 EAP reauth_request , Num=0 , Err=0 , Succ=0 PORTAL access , Num=0 , Err=0 , Succ=0 Update ack , Num=0 , Err=0 , Succ=0 PORTAL access ack , Num=0 , Err=0 , Succ=0 Session ctrl pkt , Num=0 , Err=0 , Succ=0 RADIUS sent messages statistic: Auth accept , Num=0 Auth reject , Num=0 EAP auth replying , Num=0 Account success , Num=0 Account failure , Num=0 Cut req , Num=0 RecError_MSG_sum:0 SndMSG_Fail_sum :0 Timer_Err :0 Alloc_Mem_Err :0 State Mismatch :0 Other_Error :0 No-response-acct-stop packet =0 Discarded No-response-acct-stop packet for buffer overflow =0 The other problem is that when the RADIUS server is not available I can not log in to the switch. The switch have 3 local accounts but none of them works. How can I specify the switch to use the local accounts in case that the RADIUS service is not available?

  Read the article

• How to export computers from Active Directory to XML using Powershell?

  - by CoDeRs

  I am trying to create a powershell scripts for Remote Desktop Connection Manager using the active directory module. My first thought was get a list of computers in AD and parse them out into XML format similar to the OU structure that is in AD. I have no problem with that, the below code will work just but not how I wanted. EG # here is a the array $OUs Americas/Canada/Canada Computers/Desktops Americas/Canada/Canada Computers/Laptops Americas/Canada/Canada Computers/Virtual Computers Americas/USA/USA Computers/Laptops Computers Disabled Accounts Domain Controllers EMEA/UK/UK Computers/Desktops EMEA/UK/UK Computers/Laptops Outside Sales and Service/Laptops Servers I wanted to have the basic XML structured like this Americas Canada Canada Computers Desktops Laptops Virtual Computers USA USA Computers Laptops Computers Disabled Accounts Domain Controllers EMEA UK UK Computers Desktops Laptops Outside Sales and Service Laptops Servers However if you run the below it does not nest the next string in the array it only restarts the from the beginning and duplicating Americas Canada Canada Computers Desktops Americas Canada Canada Computers Laptops Americas Canada Canada Computers Virtual Computers Americas USA USA Computers Laptops RDCMGenerator.ps1 #Importing Microsoft`s PowerShell-module for administering ActiveDirectory Import-Module ActiveDirectory #Initial variables $OUs = @() $RDCMVer = "2.2" $userName = "domain\username" $password = "Hashed Password+" $Path = "$env:temp\test.xml" $allComputers = Get-ADComputer -LDAPFilter "(OperatingSystem=*)" -Properties Name,Description,CanonicalName | Sort-Object CanonicalName | select Name,Description,CanonicalName $allOUObjects = $allComputers | Foreach {"$($_.CanonicalName)"} Function Initialize-XML{ ##<RDCMan schemaVersion="1"> $xmlWriter.WriteStartElement('RDCMan') $XmlWriter.WriteAttributeString('schemaVersion', '1') $xmlWriter.WriteElementString('version',$RDCMVer) $xmlWriter.WriteStartElement('file') $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$env:userdomain) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('userName',$userName) $xmlWriter.WriteElementString('domain',$env:userdomain) $xmlWriter.WriteStartElement('password') $XmlWriter.WriteAttributeString('storeAsClearText', 'false') $XmlWriter.WriteRaw($password) $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('size','1024 x 768') $xmlWriter.WriteElementString('sameSizeAsClientArea','True') $xmlWriter.WriteElementString('fullScreen','False') $xmlWriter.WriteElementString('colorDepth','32') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Group ($groupName){ #Start Group $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$groupName) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Server ($computerName, $computerDescription) { #Start Server $xmlWriter.WriteStartElement('server') $xmlWriter.WriteElementString('name',$computerName) $xmlWriter.WriteElementString('displayName',$computerDescription) $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() #Stop Server } Function Close-XML { $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() # finalize the document: $xmlWriter.Flush() $xmlWriter.Close() notepad $path } #Strip out Domain and Computer Name from CanonicalName foreach($OU in $allOUObjects){ $newSplit = $OU.split("/") $rebildOU = "" for($i=1; $i -le ($newSplit.count - 2); $i++){ $rebildOU += $newSplit[$i] + "/" } $OUs += $rebildOU.substring(0,($rebildOU.length - 1)) } #Remove Duplicate OU's $OUs = $OUs | select -uniq #$OUs # get an XMLTextWriter to create the XML $XmlWriter = New-Object System.XMl.XmlTextWriter($Path,$UTF8) # choose a pretty formatting: $xmlWriter.Formatting = 'Indented' $xmlWriter.Indentation = 1 $XmlWriter.IndentChar = "`t" # write the header $xmlWriter.WriteStartDocument() # # 'encoding', 'utf-8' How? # # set XSL statements #Initialize Pre-Defined XML Initialize-XML ######################################################### # Start Loop for each OU-Path that has a computer in it ######################################################### foreach ($OU in $OUs){ $totalGroupName = "" #Create / Reset Total OU-Path Completed $OU.split("/") | foreach { #Split the OU-Path into individual OU's $groupName = "$_" #Current OU $totalGroupName += $groupName + "/" #Total OU-Path Completed $xmlWriter.WriteStartElement('group') #Start new XML Group Create-Group $groupName #Call function to create XML Group ################################################ # Start Loop for each Computer in $allComputers ################################################ foreach($computer in $allComputers){ $computerOU = $computer.CanonicalName #Set the computers OU-Path $OUSplit = $computerOU.split("/") #Create the Split for the OU-Path $rebiltOU = "" #Create / Reset the stripped OU-Path for($i=1; $i -le ($OUSplit.count - 2); $i++){ #Start Loop for OU-Path to strip out the Domain and Computer Name $rebiltOU += $OUSplit[$i] + "/" #Rebuild the stripped OU-Path } if ($rebiltOU -eq $totalGroupName){ #Compare the Current OU-Path with the computers stripped OU-Path $computerName = $computer.Name #Set the computer name $computerDescription = $computerName + " - " + $computer.Description #Set the computer Description Create-Server $computerName $computerDescription #Call function to create XML Server } } } ################################################### # Start Loop to close out XML Groups created above ################################################### $totalGroupName.split("/") | foreach { #Split the if ($_ -ne "" ){ $xmlWriter.WriteEndElement() #End Group } } } Close-XML

  Read the article

• Unable to connect to OpenVPN server

  - by Incognito

  I'm trying to get a working setup of OpenVPN on my VM and authenticate into it from a client. I'm not sure but it looks to me like it's socket related, as it's not set to LISTEN, and localhost seems wrong. I've never set up VPN before. # netstat -tulpn | grep vpn Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:1194 0.0.0.0:* 24059/openvpn I don't think this is set up correctly. Here's some detail into what I've done. I have a VPS from MediaTemple: These are my interfaces before starting openvpn: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:39482 errors:0 dropped:0 overruns:0 frame:0 TX packets:39482 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3237452 (3.2 MB) TX bytes:3237452 (3.2 MB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:4885284 errors:0 dropped:0 overruns:0 frame:0 TX packets:4679884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:835278537 (835.2 MB) TX bytes:1989289617 (1.9 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:205.[redacted] P-t-P:205.186.148.82 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 I've followed this guide on setting up a basic server and getting a .p12 file, however, I was receiving an error that stated /dev/net/tun was missing, so I created it mkdir -p /dev/net mknod /dev/net/tun c 10 200 chmod 600 /dev/net/tun This resolved the error preventing the service from launching, however, I am unable to connect. On the server I've set up the myserver.conf file (as per the tutorial) to indicate local 127.0.0.1 (I've also attempted with the public IP address, perhaps I don't understand what they mean by local IP?). The server launches without error, this is what the log looks like when it starts: Sun Apr 1 17:21:27 2012 OpenVPN 2.1.3 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Mar 11 2011 Sun Apr 1 17:21:27 2012 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Sun Apr 1 17:21:27 2012 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Sun Apr 1 17:21:27 2012 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Sun Apr 1 17:21:27 2012 TUN/TAP device tun0 opened Sun Apr 1 17:21:27 2012 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500 Sun Apr 1 17:21:27 2012 GID set to openvpn Sun Apr 1 17:21:27 2012 UID set to openvpn Sun Apr 1 17:21:27 2012 UDPv4 link local (bound): [AF_INET]127.0.0.1:1194 Sun Apr 1 17:21:27 2012 UDPv4 link remote: [undef] Sun Apr 1 17:21:27 2012 Initialization Sequence Completed This creates a tun0 interface that looks like this: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the netstat command still indicates the state is not set to LISTEN. On the client-side I've installed the p12 certs onto two devices (one is an android tablet, the other is an Ubuntu desktop). I don't see port 1194 as open either. Both clients install the cert files and then ask me for the L2TP secret (which was set on the file), but then they oddly ask me for a username and a password, which I don't know where I could possibly get those from. I attempted all of my logins, and some whacky guesses that were frantically pulling at straws. If there's any more information I could provide let me know.

  Read the article

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• Troubleshooting High Load on Plesk LAMP Dedicated Server

  - by Callmeed

  I have 2 nearly identical dedicated servers with the same provider. They also run a nearly identical software stack: RedHat 5 64-bit, Plesk, PHP, Apache, & MySQL. We use them for hosting custom sites we build. The problem is, while our 1st server has a load average (in top) of around 0.3, the 2nd server consistently has a load average of around 4.0 or higher. Basic functions in Plesk are delayed and there is a bit of latency when executing shell commands. Anyone have ideas why it would be so high? And why it would differ from our other server so much? Here is my current top output (sorted by %MEM) ... Any help is much appreciated ... top - 21:48:04 up 100 days, 4:28, 1 user, load average: 3.74, 4.20, 4.23 Tasks: 336 total, 1 running, 335 sleeping, 0 stopped, 0 zombie Cpu(s): 0.8%us, 0.4%sy, 0.0%ni, 91.3%id, 7.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 12290884k total, 11886452k used, 404432k free, 2920212k buffers Swap: 2096472k total, 244k used, 2096228k free, 6560692k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22536 apache 15 0 860m 547m 6484 S 0.0 4.6 0:10.96 httpd 26467 apache 15 0 859m 546m 6408 S 0.0 4.5 0:07.67 httpd 3620 apache 15 0 859m 545m 5552 S 0.0 4.5 0:06.15 httpd 1895 apache 15 0 858m 544m 6356 S 0.0 4.5 0:08.25 httpd 16933 apache 15 0 858m 544m 5488 S 0.0 4.5 0:01.57 httpd 6431 apache 15 0 856m 542m 6076 S 10.6 4.5 0:05.32 httpd 14417 apache 15 0 856m 542m 5568 S 0.0 4.5 0:03.88 httpd 15403 apache 15 0 855m 541m 5616 S 0.0 4.5 0:03.73 httpd 19165 apache 15 0 853m 539m 6252 S 0.0 4.5 0:12.40 httpd 15898 apache 15 0 852m 539m 5376 S 0.0 4.5 0:02.68 httpd 14401 apache 15 0 851m 538m 5460 S 0.0 4.5 0:02.97 httpd 15393 apache 15 0 851m 538m 5404 S 0.0 4.5 0:03.12 httpd 15427 apache 15 0 851m 538m 5496 S 0.0 4.5 0:02.44 httpd 14412 apache 15 0 851m 538m 5324 S 0.0 4.5 0:02.15 httpd 18330 apache 15 0 851m 537m 5136 S 0.0 4.5 0:01.30 httpd 18303 apache 15 0 848m 535m 5140 S 0.0 4.5 0:00.47 httpd 21190 apache 15 0 845m 533m 3988 S 0.0 4.4 0:00.33 httpd 15923 root 18 0 822m 521m 9928 S 0.0 4.3 10:04.81 httpd 22021 apache 15 0 828m 520m 4964 S 0.0 4.3 0:00.16 httpd 22146 apache 15 0 823m 515m 3016 S 0.0 4.3 0:00.02 httpd 22345 apache 15 0 822m 514m 2408 S 0.0 4.3 0:00.00 httpd 14721 apache 15 0 733m 510m 488 S 0.0 4.3 0:00.00 httpd 5094 root 15 0 1452m 122m 15m S 1.0 1.0 852:24.24 java 4636 mysql 15 0 532m 57m 6440 S 1.0 0.5 488:05.84 mysqld 4799 popuser 15 0 166m 53m 2368 S 0.0 0.4 0:36.64 spamd 16761 popuser 15 0 159m 46m 2312 S 0.0 0.4 0:00.38 spamd 4797 root 15 0 158m 45m 2448 S 0.0 0.4 0:01.27 spamd 5074 root 34 19 255m 20m 2144 S 0.0 0.2 1:37.53 yum-updatesd 9917 named 15 0 366m 9804 1980 S 0.0 0.1 0:10.26 named 4332 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.06 sw-engine-cgi 4341 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.07 sw-engine-cgi 4350 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.09 sw-engine-cgi 4352 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.11 sw-engine-cgi 4376 ntp 15 0 23388 5020 3896 S 0.0 0.0 0:00.58 ntpd 4331 sw-cp-se 15 0 61336 4572 1480 S 0.0 0.0 5:53.22 sw-cp-serverd 4213 haldaemo 15 0 31252 4460 1684 S 0.0 0.0 0:01.52 hald 4778 postgres 18 0 117m 4164 3484 S 0.0 0.0 0:00.11 postmaster 18555 root 16 0 98.3m 3716 2852 S 0.0 0.0 0:00.01 sshd 4488 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4489 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4492 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4493 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4490 sso 18 0 119m 3040 220 S 0.0 0.0 0:00.00 sw-engine-cgi

  Read the article

• nginx 502 Bad Gateway on every external site

  - by Leandros

  I just installed nginx and followed the guides on the official site, to set it up with php5-fpm, but it just won't work. Not even the default site, without php is working outside of my server. Tried listen = 127.0.0.1:7777 and listen = /var/run/php5-fpm.sock Both don't work. I can access http://localhost with lynx on my server, but not from somewhere else (with external ip obviously). Yes, the php5-fpm deamons are running, yes the port (80 and 7777) is opened. Don't work with php-cgi as well. My config: user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; proxy_buffers 16 16k; proxy_buffer_size 32k; fastcgi_buffers 16 16k; fastcgi_buffer_size 32k; fastcgi_connect_timeout 300; fastcgi_send_timeout 300; fastcgi_read_timeout 300; } Server config: (symlinked to sites-enabled) server { server_name skilloverflow.de *.skilloverflow.de; root /var/www/blog.skilloverflow.de/htdocs; index index.php; error_log /var/log/nginx/skilloverflow.error.log; access_log /var/log/nginx/skilloverflow.access.log; location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } location / { # This is cool because no php is touched for static content. # include the "?$args" part so non-default permalinks doesn't break when using query string try_files $uri $uri/ /index.php?$args; } location ~ [^/]\.php(/|$) { fastcgi_split_path_info ^(.+?\.php)(/.*)$; if (!-f $document_root$fastcgi_script_name) { return 404; } fastcgi_pass 127.0.0.1:7777; fastcgi_index index.php; include fastcgi_params; } location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires max; log_not_found off; } # deny access to apache .htaccess files location ~ /\.ht { deny all; } # deny access to apache .htaccess files location ~ /\.ht { deny all; } } PHP Version: 5.4.17-1 nginx version: 1.2.1 Debian 6.0.7 Linux 2.6.32 Edit: Lighttpd is still installed, does that matter? It's not running though. Edit 2: No error or access log is generated. They're all empty.

  Read the article

• Apache reverse proxy POST 403

  - by qkslvrwolf

  I am trying to get Jira and Stash to talk to each other via a Trusted Application link. The setup, currently, looks like this: Jira - http - Jira Proxy -https- stash proxy -http- stash. Jira and the Jira proxy are on the same machine. The Jira Proxy is showing 403 Forbidden for POST requests from the stash server. It works (or seems to ) for everything else. I contend that since we're seeing 403 forbiddens in the access log for apache, Jira is never seeing the request. Why is apache forbidding posts,and how do I fix it? Note that the IPs for both Stash and the Stash Proxy are in the "trusted host" section. My config: LogLevel info CustomLog "|/usr/sbin/rotatelogs /var/log/apache2/access.log 86400" common ServerSignature off ServerTokens prod Listen 8443 <VirtualHost *:443> ServerName jira.company.com SSLEngine on SSLOptions +StrictRequire SSLCertificateFile /etc/ssl/certs/server.cer SSLCertificateKeyFile /etc/ssl/private/server.key SSLProtocol +SSLv3 +TLSv1 SSLCipherSuite DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA:DHE-RSA-AES128-SHA:DHE-DSS-AES128-SHA:AES128-SHA:EDH-RSA-DES-CBC3-SHA:EDH-DSS-DES-CBC3-SHA:DES-CBC3-SHA # If context path is not "/wiki", then send to /jira. RedirectMatch 301 ^/$ https://jira.company.com/jira RedirectMatch 301 ^/gsd(.*)$ https://jira.company.com/jira$1 ProxyRequests On ProxyPreserveHost On ProxyVia On ProxyPass /jira http://localhost:8080/jira ProxyPassReverse /jira http://localhost:8080/jira <Proxy *> Order deny,allow Allow from all </Proxy> RewriteEngine on RewriteLog "/var/log/apache2/rewrite.log" RewriteLogLevel 2 # Disable TRACE/TRACK requests, per security. RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] DocumentRoot /var/www DirectoryIndex index.html <Directory /var/www> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> <LocationMatch "/"> Order deny,allow Deny from all allow from x.x.71.8 allow from x.x.8.123 allow from x.x.120.179 allow from x.x.120.73 allow from x.x.120.45 satisfy any SetEnvif Remote_Addr "x.x.71.8" TRUSTED_HOST SetEnvif Remote_Addr "x.x.8.123" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.179" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.73" TRUSTED_HOST SetEnvif Remote_Addr "x.x.120.45" TRUSTED_HOST </LocationMatch> <LocationMatch ^> SSLRequireSSL AuthType CompanyNet PubcookieInactiveExpire -1 PubcookieAppID jira.company.com require valid-user RequestHeader set userid %{REMOTE_USER}s </LocationMatch> </VirtualHost> # Port open for SSL, non-pubcookie access. Used to access APIs with Basic Auth. <VirtualHost *:8443> SSLEngine on SSLOptions +StrictRequire SSLCertificateFile /etc/ssl/certs/server.cer SSLCertificateKeyFile /etc/ssl/private/server.key SSLProtocol +SSLv3 +TLSv1 SSLCipherSuite DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA:DHE-RSA-AES128-SHA:DHE-DSS-AES128-SHA:AES128-SHA:EDH-RSA-DES-CBC3-SHA:EDH-DSS-DES-CBC3-SHA:DES-CBC3-SHA ProxyRequests On ProxyPreserveHost On ProxyVia On ProxyPass /jira http://localhost:8080/jira ProxyPassReverse /jira http://localhost:8080/jira <Proxy *> Order deny,allow Allow from all </Proxy> RewriteEngine on RewriteLog "/var/log/apache2/rewrite.log" RewriteLogLevel 2 # Disable TRACE/TRACK requests, per security. RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] DocumentRoot /var/www DirectoryIndex index.html <Directory /var/www> Options FollowSymLinks AllowOverride None Order deny,allow Allow from all </Directory> </VirtualHost> <VirtualHost jira.company.com:80> ServerName jira.company.com RedirectMatch 301 /(.*)$ https://jira.company.com/$1 RewriteEngine on RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] </VirtualHost> <VirtualHost *:80> ServerName go.company.com RedirectMatch 301 /(.*)$ https://jira.company.com/$1 RewriteEngine on RewriteCond %{REQUEST_METHOD} ^(TRACE|TRACK) RewriteRule .* - [F] </VirtualHost>

  Read the article

< Previous Page | 418 419 420 421 422 423 424 425 426 427 428 429  | Next Page >