Search Results

Search found 15591 results on 624 pages for 'problems'.

Page 426/624 | < Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• iTunes' clandestine proxy settings

  - by pilcrow

  Problem: One user's iTunes consults a defunct HTTP proxy, but only for iTunes Store HTTP requests -- other iTunes web requests are unproxied. How do I dismiss this spurious proxy setting? Background: It's not as easy as Internet Options. Years ago my network had a mandatory HTTP proxy at 172.31.1.1:8080. When we switched to the 192.168.1/24 space and eliminated the proxy, this user's iTunes -- the only iTunes user at the time -- could no longer contact the iTunes Store, an operation which fails with "unknown error -9808". This has been the case through several iTunes.exe upgrades over the years and prevents, among other things, activation of a new or newly upgraded iPhone. wireshark and TCPView confirm that this user's iTunes.exe is attempting to contact the long-defunct http proxy when attempting to reach the iTunes Store, but is otherwise unproxied. Curious details: No other iTunes.exe HTTP traffic for this user is affected -- iTunes can successfully make HTTP chatter at Apple's servers. No other web traffic at all is proxied, whether this user or others, iTunes or browser, etc. I cannot find the spurious proxy setting anywhere in the registry nor on disk, though perhaps I haven't thought of every place to look and every format to look for. Other users who have experienced the same error code all seem to have unrelated web configuration problems (certificate validation, for example). UPDATE in response to Phoshi's excellent suggestion, reinstallation hasn't done the trick.

  Read the article

• How do I fix issue causing "incomplete startup packet" log message trying to implement replication in Postgresql?

  - by colour me brad

  I've got two cloud servers running Ubuntu 13.04 and PostgreSQL 9.2. I've primarily used this blog post to aid me in setting things up. However, to do the initial database dump to the slave I'm using pg_start_backup/pg_stop_backup strategy used in this other blog post. I've read through the docs and postgres wikis as well. I ran into several problems I was able to solve, but I can't get past this wretched "the database is starting up" failure. I'm not sure if seeing "cp: cannot stat '/var/lib/postgresql/9.2/archive/00000001000000000000003A': No such file or directory" after "consistent recover state reached" is normal or the first sign of a problem. The searching I've done on "the database is starting up" and "incomplete startup packet" tells me that something is sending empty TCP packets to the slave. The only thing that even knows about the slave is the master, so I'm not sure why it's sending empty packets... Has anyone worked with this and have an idea what might be going wrong? The postgres log on the slave looks like so: 2013-08-26 13:01:38 CDT LOG: entering standby mode 2013-08-26 13:01:38 CDT LOG: restored log file "000000010000000000000039" from archive 2013-08-26 13:01:38 CDT LOG: incomplete startup packet 2013-08-26 13:01:39 CDT LOG: redo starts at 0/39000020 2013-08-26 13:01:39 CDT LOG: consistent recovery state reached at 0/390000E0 cp: cannot stat '/var/lib/postgresql/9.2/archive/00000001000000000000003A': No such file or directory 2013-08-26 13:01:39 CDT LOG: streaming replication successfully connected to primary 2013-08-26 13:01:39 CDT FATAL: the database system is starting up 2013-08-26 13:01:39 CDT FATAL: the database system is starting up 2013-08-26 13:01:40 CDT FATAL: the database system is starting up 2013-08-26 13:01:40 CDT FATAL: the database system is starting up 2013-08-26 13:01:41 CDT FATAL: the database system is starting up 2013-08-26 13:01:42 CDT FATAL: the database system is starting up 2013-08-26 13:01:42 CDT FATAL: the database system is starting up 2013-08-26 13:01:43 CDT FATAL: the database system is starting up 2013-08-26 13:01:43 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT LOG: incomplete startup packet 2013-08-26 13:03:27 CDT FATAL: the database system is starting up 2013-08-26 13:03:27 CDT FATAL: the database system is starting up 2013-08-26 13:03:30 CDT FATAL: the database system is starting up 2013-08-26 13:03:30 CDT FATAL: the database system is starting up thanks! brad

  Read the article

• puppet cert mismatch in ec2

  - by Stick

  I'm setting up a puppetmaster (2.7.6) in ec2 via gems (on rhel6) and I'm running into problems with the cert names and getting the master able to talk to itself. my puppet.conf looks like this: [main] logdir = /var/log/puppet rundir = /var/run/puppet vardir = /var/lib/puppet ssldir = $vardir/ssl pluginsync = true environment = production report = true certname = master When I start the puppetmaster process the ssl directory looks like: ssl/private_keys/master.pem ssl/crl.pem ssl/public_keys/master.pem ssl/ca/ca_crl.pem ssl/ca/signed/master.pem ssl/ca/ca_crt.pem ssl/ca/ca_pub.pem ssl/ca/ca_key.pem ssl/certs/ca.pem ssl/certs/master.pem I have an /etc/hosts entry on the box to point the 'puppet' hostname to localhost so that I don't have to change the 'server' option. When I run the agent I get the following: # puppet agent --test info: Retrieving plugin err: /File[/var/lib/puppet/lib]: Failed to generate additional resources using 'eval_generate: Server hostname 'puppet' did not match server certificate; expected master err: /File[/var/lib/puppet/lib]: Could not evaluate: Server hostname 'puppet' did not match server certificate; expected master Could not retrieve file metadata for puppet://puppet/plugins: Server hostname 'puppet' did not match server certificate; expected master err: Could not retrieve catalog from remote server: Server hostname 'puppet' did not match server certificate; expected master warning: Not using cache on failed catalog err: Could not retrieve catalog; skipping run err: Could not send report: Server hostname 'puppet' did not match server certificate; expected master If I specify the certname as the server (with corresponding hosts entry) I get: # puppet agent --test --server master info: Retrieving plugin err: /File[/var/lib/puppet/lib]: Could not evaluate: Could not retrieve information from environment production source(s) puppet://master/plugins info: Caching catalog for master info: Applying configuration version '1321805956' notice: Finished catalog run in 0.05 seconds Which is success of a sort, that source error will bite me later when I'm applying manifests. I've tried a couple of other variations with using the ec2 private hostname and gotten mixed results. I'd like to avoid setting server = 'x' and use dns/hosts to control what 'puppet' resolves to in order to decide which server (plays easier with availability zones, etc)

  Read the article

• Put one monitor of a dual monitor windows system into standby

  - by Psycogeek

  Standby not Disabled! When running 2 monitors on windows 7 or Windows XP, I would like to be able to put one of the monitors at a time into standby. The method can be manual. When running 2 monitors , the second monitor is not always needed, shutting off the monitors own power switch will turn off the monitor, that does work Ok. Problems with that are , the delay with the monitor logo at turn on, and the power switch is not very accessable, and the switch might not live forever turning it on and off so many times. Using disable methods like devcon, WIN-P and Display, causes all the windows to properly move to the other monitor. While that is what a person would want to happen so they can get hold of the windows, that is not what I want to happen, and some things on the other monitor have to be re-arranged after a re-enable. By putting it into standby mode, nothing changes other than the monitor going into standby. Disconnecting the DVI cable still can cause the system to (properly) shift all the windows over to the one monitor, just like any of the disable methods do. That makes a mess of the windows, and is so unacceptable, that I would prefer to leave the monitor on, wasting power and the hardware, when it could easily go into standby for some time. For both monitors I am using a "MonitorOff" program that puts both monitors into standby, but I can not find a utility that will put only ONE monitor into standby for the windows system. If someone comes along and suggests "ultramon" you must know for a fact that it will put One of either of the monitors into actual standby. And it does not really suit me to use ultramon, I tested it (it was nice) and I did not feel that it was a program I wanted. The 2 monitors are running off of an ATI 4890 card, they are both hooked up DVI-I, the OS is both Windows 7 (primary) and Windows XP. In addition it would also be interesting to have seperate standby activity timers, and follow mouse kind of standby changes, but any manuel method , shortcut, batch , tray, or gadget kind of operation would be a good start.

  Read the article

• How to install VMware tools for Ubuntu 11.04 hosted on VMware ESXi?

  - by Dmitri Toubelis

  I'm running Vmware ESX 4.1 and I have a development VM that I recently upgraded from Ubuntu 10.04 to 11.04. Then I tried to re-install VMware Tools and some of the modules gave me an error and would not compile. As a result I'm having problems with backing up this virtual machine now and I suspect VMware tools is the reason. I installed latest patches for VMware host, that included an update to VMware Tools (v8.3.7 build-381511) but I'm still getting the same error. The error I'm getting is like this: ... /tmp/vmware-root/modules/vmhgfs-only/super.c:73:4: error: unknown field \u2018clear_inode\u2019 specified in initializer make[2]: *** [/tmp/vmware-root/modules/vmhgfs-only/super.o] Error 1 make[1]: *** [_module_/tmp/vmware-root/modules/vmhgfs-only] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.38-8-generic' make: *** [vmhgfs.ko] Error 2 make: Leaving directory `/tmp/vmware-root/modules/vmhgfs-only' and also this: /tmp/vmware-root/modules/vmci-only/vmci_drv.c:91:4: error: unknown field \u2018ioctl\u2019 specified in initializer /tmp/vmware-root/modules/vmci-only/vmci_drv.c:91:4: warning: initialization from incompatible pointer type /tmp/vmware-root/modules/vmci-only/vmci_drv.c: In function \u2018vmci_init\u2019: /tmp/vmware-root/modules/vmci-only/vmci_drv.c:151:4: error: implicit declaration of function \u2018init_MUTEX\u2019 make[2]: *** [/tmp/vmware-root/modules/vmci-only/vmci_drv.o] Error 1 make[1]: *** [_module_/tmp/vmware-root/modules/vmci-only] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.38-8-generic' make: *** [vmci.ko] Error 2 make: Leaving directory `/tmp/vmware-root/modules/vmci-only' Any ideas?

  Read the article

• Mysql: Disk is full writing

  - by elma

  Hi there, I'm having some problems with my mysql server lately, so I've decided to check the error logs: [root@LSN-D1179 log]# tail -10 mysqld.log 100325 19:30:03 [ERROR] /usr/libexec/mysqld: Table './lfe/actions' is marked as crashed and should be repaired 100325 19:30:03 [ERROR] /usr/libexec/mysqld: Table './lfe/actions' is marked as crashed and should be repaired 100325 19:30:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:34:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:39:46 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_posts.TMD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:40:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:44:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:49:46 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_posts.TMD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:50:18 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_task_logs.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs 100325 19:54:34 [ERROR] /usr/libexec/mysqld: Disk is full writing './omuz/ibf_profile_portal_views.MYD' (Errcode: 122). Waiting for someone to free space... Retry in 60 secs And here's is my df -h output [root@LSN-D1179 log]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 143G 6.2G 129G 5% / /dev/sda1 99M 12M 83M 13% /boot tmpfs 490M 0 490M 0% /dev/shm As you can see, I have plenty of free space; so I couldn't figure out these "Disk is full" errors in mysqld.log. Does anyone know what should I do to fix this? Ugur

  Read the article

• How do I install OpenStack on a single Ubuntu 12.04 node?

  - by Sam Edwards

  I'm having trouble installing OpenStack in Ubuntu 12.04, for various reasons: The official Ubuntu website recommends Juju and MAAS. However, this is a single node I am trying to get OpenStack installed on, and MAAS requires "two or more nodes" according to the docs. Additionally, I don't have any experience in MAAS and Juju and would rather stick to technologies I am more familiar with so that I can debug problems that arise. I have tried StackGeek but this fails because the node only has a single Ethernet port. The node does, however, have the second hard drive required for the nova storage. I have tried DevStack but cannot log into the dashboard. The login form appears fine, but as soon as I try to submit the page, my browser begins loading indefinitely. I have tried installing straight from packages, but I get an Internal Server Error in the dashboard upon trying to log in, with no helpful logs anywhere in sight to aid me in debugging the issue. Each of these attempts was with a fresh Ubuntu 12.04 LTS setup; I'm finding it really strange that no matter what I try, I cannot get OpenStack installed. Is this even a stable/mature project? Why am I encountering so many bugs?

  Read the article

• I cannot format my PC

  - by Jesus Buelna

  I have a Toshiba Satellite(1) l505 6gb RAM, 6.00GB hard disk.Initially I have problem with another satellite(2) I had (mother board problem). I took my Laptop to a technician and cost a lot of money (almost as much as buying new one). So, since I have HDD problems with the first one(1) I decided to use the hard disk of the other one(2). I formatted the HDD and erased the partitions it had into 1 partition (or no partition). The problem is that when I try to format with the SO CD, in the screen, where I have to decide in which partition I want to install the SO, the only one option I have says "unallocated partition and I receive this message "Windows cannot install the SO in this partition, run files do not existed or maybe corrupted" When I erased the disk with Parted Magic, Did I erased any files needed for running the installing disk? I don't know. Is it possible to fixed or reinstate the disk to install the OS? By the way, I checked the disk physical health with Parted Magic, and it is OK. One more thing when I erased the disc to 0, I used the safety option offered by the Parted Magic.Need help please.

  Read the article

• How to stop SophosAV from scanning directories under source control

  - by user26453

  From googling it seems its well known that SophosAV as well as other AV programs have issues with how they interact and can inhibit source control utilities like TortoiseHG or TortoiseSVN. One solution is to exclude directories under source control from on-access scanning as detailed here on Sophos's support site. There is a corollary article that mentions some issues related to this, namely need to place multiple entries for exclusions based on the possibility of the location being accessed through the short vs. long name (e.g., Progra~1 vs. "Program Files"). One other twist is I am using a junction to relocate my user directory, C:\Users\Username, to a second hard drive, E:. Since I am not sure how this interacts I have included the source control directory as they are nested in both locations. As a result, I have included the two exclusions for the on-access scanning exclusions (and to be on the safe side on-demand exclusions as well, although this should only come into play when I select a parent directory of the exclusion to be scanned on-demand, but still). You'll notice I have no need to add extra exclusions for those locations based on short vs. long name distinctions. The two exclusion I have then, for both on-access and on-demand scanning exclusions are: C:\Users\Username\source-control-directory E:\source-control-directory However, this does not seem to work as TortoiseHG still lags terribly in response to any request as AV software starts scanning when the directory is accessed via TortoiseHG. I can verify without a doubt that Sophos is causing the problems: I can completely disable on-access scanning. Once this is done TortoiseHG responds very fast to all operations. I cannot leave this disabled obviously, but since the exclusion don't seem to be working, what next?

  Read the article

• Can't connect to local MySQL server through socket

  - by Martin

  I was trying to tune the performance of a running mysql-server by running this command: mysqld_safe --key_buffer_size=64M --table_cache=256 --sort_buffer_size=4M --read_buffer_size=1M & After this i'm unable to connect mysql from the server where mysql is running. I get this error: ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) However, luckily i can still connect to mysql remotely. So all my webservers still have access to mysql and are running without any problems. Because of this though i don't want to try to restart the mysql server since that will probably mess everything up. Now i know that mysqld_safe is starting the mysql-server, and since the mysql server was already running i guess it's some kind of problem with two mysql servers running and listening to the same port. Is there some way to solve this problem without restarting the initial mysql server? UPDATE: This is what ps xa | grep "mysql" says: 11672 ? S 0:00 /bin/sh /usr/bin/mysqld_safe 11780 ? Sl 175:04 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --socket=/var/run/mysqld/mysqld.sock --port=3306 11781 ? S 0:00 logger -t mysqld -p daemon.error 12432 pts/0 R+ 0:00 grep mysql

  Read the article

• New 3TB HDD, can see full 2.7TB in Linux and Windows, but shows up as 801.6GB in BIOS

  - by Ben Lee

  I recently purchased a Seagate Barracuda 3TB drive (ST3000DM001). After installing it, my BIOS recognized it but reported the size as 801.6gb. I went ahead and booted into Linux anyway (Ubuntu 11.10 64-bit). Linux saw it as a 2.7TB. Following some online instructions (don't have the link handy, unfortunately), it looks liked converting this drive to GPT was recommended. So I used gparted to do that, then formatted it to NTFS also using gparted. (I'm using NTFS because my machine is daul-boot and I want to have access to the drive in Windows too). I rebooted to Windows (Windows 7 64-bit), and Windows also sees the drive with 2.7TB free. Everything seems to be working fine. The only issue is that my BIOS is still reporting the drive as 801.6GB. My motherboard is an ASRock 770 Extreme3 and BIOS is the latest version. Since everything seems to be working with the new drive anyway, I'm hoping that the fact that the BIOS is reporting the wrong size is not an actual problem. But honestly, I don't really know. Anyone out there more familiar with this know if this could potentially cause any problems in the future? Any way to get the BIOS to report the correct size?

  Read the article

• Ubuntu NBR karmic boot freezes at fsck from util-linux-ng 2.16

  - by BlueBill

  Hi all, I have a netbook (emachine e250 - equivalent to an acer aspire one) and I have Ubunutu NBR 9.10 installed on it. Every other cold boot freezes at the following error message: "fsck from util-linux-ng 2.16" There is no disk activity, no activity what so ever. I have left the machine sit for over an hour and nothing. It takes a couple of hard resets to be able to boot properly. Once it boots everything works great (wireless, suspend/resume, etc.)! I have spent the last couple of weeks researching the problem and the only thing that seems to work is setting nolapic in the boot string in grub - it boots every time. Unfortunately, nolapic disables the second core and causes problems with suspend resume. At first I thought it was an fsck problem with the first partition on the hard disk as it is a hidden ntfs partition containing the windows xp recover information. So in /etc/fstab I set the partition so that it would be ignored by fsck. This didn't seem to do anything. I have these partitions: /dev/sda1 - an ntfs recovery partition /dev/sda2 - /boot /dev/sda3 - swap /dev/sda5 - / /dev/sda6 - /home I am running kernel version 2.6.31-19-generic and have all the patches (as indicated by update manager). I also have no splash screen so I can see the boot progress. I have only been using NBR since January, I have been using Ubuntu on my desktop since last June (2009-06). What logs should I be looking at? Is there a log for failed boots? Thanks, Troy

  Read the article

• Files Corrupted on System Restore

  - by Yar

  I restored OSX 10.6.2 today (was 10.6.3 and not booting) by copying the system over from a backup. The data directories were not touched. I am seeing some files as 0 bytes, and getting permission-denied errors when copying, even when using sudo cp or the Finder itself. Some programs, differently, take the files at face value and see no permission problems (such as zip), but they see the files as zero bytes, which would be game-over for recovery. cp: .git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: could not copy extended attributes to /eraseme/blah/.git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: Operation not permitted I have tried sudo chown, sudo chmod -R 777 and sudo chflags -R nouchg which do not change the end result. Strangely, this is only affecting my .git directories (perhaps because they start with a period, but renaming them -- which works -- does not change anything). What else can I do to take ownership of these files? Edit: This question comes from StackOverflow because I originally thought it was a GIT problem. It's definitely not (just) GIT. Anyway, this is to help put some of the comments in context.

  Read the article

• Citrix Access Gateway with Citrix Receiver

  - by vm370

  I'm currently using a Citrix Access Gateway with firmware 5.0.4 to provide access over an SSL-VPN to an isolated environment, which is connected to over the Citrix Access Gateway Client, which is delivered by the device by default. However we encountered different problems, e.g. that it's somehow not possible to get it out of the autostart (not registered as a service or in the autostart?!) and it killed the Cisco VPN Client, which is used in the company and unfortunately cannot be replaced. The Cisco client can also just be used again after a procedure with cleaning the registry from all CAG Client remains, which requires a lot of effort. Because of that, I'd like to check if there is an alternative to this client, since is this is a real pain... Unfortunately I couldn't find a way to use the Receiver with the CAG yet, but if you have any resources on how to build this workaround, I'd be very happy. Thanks a lot in advance UPDATE: If there are other alternatives I'd be even more happy, since using the Receiver would also mean that there is an issue with the ICA-Client, which is also used in our environments. From my experience, the Receiver and the ICA-Client are also no good friends...

  Read the article

• VMWare Fusion: "No Permission to access this virtual machine"

  - by Craig Walker

  I had a VMWare Fusion VM backed up on my home network file server (Ubuntu). I wanted to run it again, so I copied it back to my Macbook. When I tried to launch it in VMWare, I got an error message: No permission to access this virtual machine. Configuration file: /Users/craig/WinXP Clean + Scanner.vmwarevm/WinXP Pro Test.vmx The permissions look fine to me: The bundle directory is 777 The bundle files (including the listed .vmx) are all 666 User is craig (my current user); group is staff. I changed the group to wheel at the suggestion of this page, but that didn't help. Finder shows read & write for craig, staff, and everyone on the bundle directory The bundle dir is also not locked Finder also shows rw and unlocked for the .vmx file The parent directory is also rw & unlocked Disk Utility permissions check doesn't show any problems with any of the associated files It sure looks like I should have wide open access to run this VM; why is Fusion complaining?

  Read the article

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• Create SAMBA node trust relationship to Windows 2003 PDC server

  - by Rod Regier

  I am having problems creating a trust relationship between an OpenVMS/IA64 node running V/IA64 8.3-1H1, TCPIP 5.6 ECO 5, CIFS 1.1 ECO1 PS11 (SAMBA 3.0.28a) and Windows 2003 server running as a PDC. I do have two other OpenVMS/Alpha nodes running V/A 8.3, TCPIP 5.6 ECO 4, CIS 1.1 ECO1 PS10 (SAMBA 3.0.28a) with working trust relationships to the same Windows 2003 server. Looking for assistance in resolving the trust "handshake". \\ Details from failing node. Unless otherwise noted, corresponding files on working nodes are similar or identical. SMB.CONF extract: [global] server string = Samba %v running on %h (OpenVMS) workgroup = WILMA netbios name = %h security = DOMAIN encrypt passwords = Yes name resolve order = lmhosts host wins bcast Password server = * log file = /samba$log/log.%m printcap name = /sys$manager/ucx$printcap.dat guest account = DYMAX print command = print %f/queue=%p/delete/passall/name="""""%s""""" lprm command = delete/entry=%j map archive = No printing = OpenVMS net rpc testjoin [2010/08/13 16:09:28, 0] SAMBA$SRC:[SOURCE.RPC_CLIENT]CLI_PIPE.C;1:(2443) get_schannel_session_key: could not fetch trust account password for domain 'WILMA' [2010/08/13 16:09:28, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC_JOIN.C;1:(72) net_rpc_join_ok: failed to get schannel session key from server W2K3AD2 for domain WILMA. Error was NT_STATUS_CANT_ACCESS_DOMAIN_I NFO Join to domain 'WILMA' is not valid net rpc join "-Uaccount%password" tdb_open_isam: error verifying status of file SAMBA$ROOT:[PRIVATE]secrets.tdb tdb_open_isam: errno value = 1 [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.PASSDB]SECRETS.C;1:(72) Failed to open /SAMBA$ROOT/PRIVATE/secrets.tdb [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC.C;1:(322) error storing domain sid for WILMA tdb_open_isam: error verifying status of file SAMBA$ROOT:[PRIVATE]secrets.tdb tdb_open_isam: errno value = 1 [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.PASSDB]SECRETS.C;1:(72) Failed to open /SAMBA$ROOT/PRIVATE/secrets.tdb [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC_JOIN.C;1:(409) error storing domain sid for WILMA Unable to join domain WILMA. \\ Example from other node: net rpc testjoin Join to 'WILMA' is OK

  Read the article

• Apache Won't Restart After Compiling PHP with Postgres

  - by gonzofish

  I've compiled PHP (v5.3.1) with Postgres using the following configure: ./configure \ --build=x86_64-redhat-linux-gnu \ --host=x86_64-redhat-linux-gnu \ --target=x86_64-redhat-linux-gnu \ --program-prefix= \ --prefix=/usr/ \ --exec-prefix=/usr/ \ --bindir=/usr/bin/ \ --sbindir=/usr/sbin/ \ --sysconfdir=/etc \ --datadir=/usr/share \ --includedir=/usr/include/ \ --libdir=/usr/lib64 \ --libexecdir=/usr/libexec \ --localstatedir=/var \ --sharedstatedir=/usr/com \ --mandir=/usr/share/man \ --infodir=/usr/share/info \ --cache-file=../config.cache \ --with-libdir=lib64 \ --with-config-file-path=/etc \ --with-config-file-scan-dir=/etc/php.d \ --with-pic \ --disable-rpath \ --with-pear \ --with-pic \ --with-bz2 \ --with-exec-dir=/usr/bin \ --with-freetype-dir=/usr \ --with-png-dir=/usr \ --with-xpm-dir=/usr \ --enable-gd-native-ttf \ --with-t1lib=/usr \ --without-gdbm \ --with-gettext \ --without-gmp \ --with-iconv \ --with-jpeg-dir=/usr \ --with-openssl \ --with-zlib \ --with-layout=GNU \ --enable-exif \ --enable-ftp \ --enable-magic-quotes \ --enable-sockets \ --enable-sysvsem \ --enable-sysvshm \ --enable-sysvmsg \ --with-kerberos \ --enable-ucd-snmp-hack \ --enable-shmop \ --enable-calendar \ --with-libxml-dir=/usr \ --enable-xml \ --with-system-tzdata \ --with-mime-magic=/usr/share/file/magic \ --with-apxs2=/usr/sbin/apxs \ --with-mysql=/usr/include/mysql \ --without-gd \ --with-dom=/usr/include/libxml2/libxml \ --disable-dba \ --without-unixODBC \ --disable-pdo \ --enable-xmlreader \ --enable-xmlwriter \ --without-sqlite \ --without-sqlite3 \ --disable-phar \ --enable-fileinfo \ --enable-json \ --without-pspell \ --disable-wddx \ --with-curl=/usr/include/curl \ --enable-posix \ --with-mcrypt \ --enable-mbstring \ --with-pgsql=/mnt/mv/pgsql I'm using Postgres 8.4.0 and Apache 2.2.8; I have the following line in my Apache conf file: LoadModule php5_module /usr/lib64/httpd/modules/libphp5.so And when I attempt to restart Apache, I get the following error message: Starting httpd: httpd: Syntax error on line 205 of /etc/httpd/conf/httpd.conf: Cannot load /usr/lib64/httpd/modules/libphp5.so into server: /usr/lib64/httpd/modules/libphp5.so: undefined symbol: lo_import_with_oid Now, I know that this is a problem with Postgres with PHP because lo_import_with_oid is a function in the Postgres source which allows the importing of large objects; also, if I remove the --with-pgsql option, PHP and Apache get along great. I've scoured the Internet looking for answers all day, but to no avail. Does anyone have ANY insight into what is causing my problems.

  Read the article

• Linux Distro for Beginners

  - by XLR3204S

  Well... I know that's the question arising all over the Internet, but I couldn't find an answer to suit me after googling for quite some time. I'd like to get a Linux distribution, and start learning using the CLI. I'm looking for a distribution already having GNOME installed, as I'll be using Linux-Command.org as my learning resource, and I'm not very familiar with CLI-based web browsers. I'd mainly like to get to know my way around a UNIX-based system, and then I think I'd like to pick up a CLI-only distribution, and start doing more complex stuff. I've tried Ubuntu, Fedora Core, OpenSolaris and FreeBSD (the last two aren't linux distros, I know). Ubuntu and FC are fine, they do come with Firefox, but I'm not really sure they're meant for learning purposes. OpenSolaris was OK as well, but I haven't got to play with it enough. FreeBSD 7.2 did not want to install itself on my 13" MacBook Pro, it generated a kernel panic everytime while copying the files to the disk. So to sum this up, I'm trying to learn Linux, and I'm willing to invest time into this (that is, not giving up when the first problems arise). I also have intermediate knowledge of C++, if it helps, and I'm also using the CLI-vim to write small C++ CLI-based programs, so text editing should be any problem. And... speaking of Macs, how am I going to be limited if I try to learn how to use UNIX-based systems using the OS X Terminal? It uses bash 3.2, isn't this the same shell as the one found on most of the Linux machines? How does the fact that OS X is based on FreeBSD 4.4, if I'm not mistaking, affect this? Thanks in advance, and hopefully, I'll have a starting point ASAP.

  Read the article

• Asterisk/FreePBX: Allow other Google Talk clients to ring when using motif module

  - by larsks

  I've recently installed FreePBX to act as a link between a SIP soft phone and my Google Talk account. It was easy to set up and outbound calls work just fine, but I've run into two problems with inbound calls that I'm not sure how to resolve. I'm using an inbound route to forward all calls from Google to my soft phone. If the soft phone is not currently registered, Asterisk answers and immediately generates a fast-busy signal (reporting CHANUNAVAIL in the logs), and the call is lost. If the soft phone is registered, Asterisk "answers" the call before rining the soft phone, which means that other Google Talk clients never ring (since from their perspective someone has answered the call). For solving (1) seems like I could use the ChanIsAvail() function (or this answer) to prevent Asterisk from answering in the event that the phone isn't registered. However, I'm not sure what to do about (2), because the behavior I want is for Asterisk to not "answer" the call until I answer the call on the soft phone. How do I configure Asterisk (ideally within the FreePBX framework) such that I can continue to receive calls at other Google Talk clients in addition to forwarding them to a SIP phone?

  Read the article

• VMware databursts to vCenter

  - by Erwin Blonk

  [edit Nov.16th 2009: Thank you for the responses. I'm no longer on this project so the problem is out of my hands. Be sure I will return with other problems :-) ] I have a strange occurence of regular databursts over my WAN links from 2 sites to a site with vCenter. What happens is that a vCenter server is managing local ESX 3.5 servers and 2 from 2 sites across a WAN link. Each server sends an approximately 3MB worth of TLS data (less than 10% of the time it varies to higher or lower) every 15 minutes (with a margin of 2 minutes). So far, I've not been able to single out a process that causes it. I looked through all applications on each site. So far, it seems to originate from one server on each site. Although it may be coincidence and therefore not relevant, I found that one server, with very few exceptions, does a burst at 00:00 on the hour. The other 3 during the hour are a bit off the 15 minute mark but back at the top of the hour, you can sync your watch on it. The other server follows 5 minutes after that with no such precision. But, as said, it never differs more than 2 minutes. Servers are ESX 3.5, vCenter is 2.5.

  Read the article

• haproxy and tomcat intermittent hangs

  - by user7347

  I am trying to run haproxy in front of tomcat on a Solaris x86 box, but I am getting intermittent failures. At seemingly random intervals, the request just hangs until haproxy times out the connection. I thought maybe it was my app, but I've been able to reproduce it with the tomcat manager app, and hitting tomcat directly there is no problems at all. Hitting it repeatedly with curl will cause the error within 10-15 tries curl -ikL http://admin:admin@<my server>:81/manager/status haproxy is running on port 81, tomcat on port 7000. haproxy returns a 504 gateway timeout to the client, and puts this into the log file: Sep 7 21:39:53 localhost haproxy[16887]: xxx.xxx.xxx.xxx:65168 [07/Sep/2009:21:39:23.005] http_proxy http_proxy/tomcat7000 5/0/0/-1/30014 504 194 - - sHNN 0/0/0/0/0 0/0 "GET /manager/status HTTP/1.1" Tomcat shows nothing, no error in the logs and no indication that the request ever makes it to the tomcat server. The request count is not incremented, the manager app only shows activity on one thread, serving up the manager app. Here are my haproxy and tomcat connector settings, I've been playing with both a good deal trying to chase down the issue, so they may not be ideal, but they definitely don't seem like they should cause this error. server.xml <Connector port="7000" protocol="HTTP/1.1" enableLookups="false" maxKeepAliveRequests="1" connectionLinger="10" /> haproxy config global log loghost local0 chroot /var/haproxy listen http_proxy :81 mode http log global option httplog option httpclose clitimeout 150000 srvtimeout 30000 contimeout 3000 balance roundrobin cookie SERVERID insert server tomcat7000 127.0.0.1:7000 cookie server00 check inter 2000

  Read the article

• bind9 "error sending response: host unreachable"

  - by wolfgangsz

  of course), I have a number of DNS servers, all running bind9 (9.5.1, to be specific) under fedora. 4 of them are slaves, fed by a common master for our public DNS. These are all located on the public gateways of our various offices. One of them has tons of messages in its log files similar to these: Jul 21 17:26:18 gateway named[3487]: client 10.171.3.8#52500: view internal: error sending response: host unreachable I wonder where that comes from. The firewall is open on port 53 between the two machines (10.171.3.8 is an internal DNS server located on a Windows Domain Controller). The internal domains do NOT list the gateway as a name server (so there should not be any attempts of replicating the domains), and the gateway does not handle any internal DNS. The clients in these messages vary between the two domain controllers on the internal network and a third internal name server (running bind9 on debian in a different segment of the network). Any pointers are highly welcome. In response to the first reply: The issue with this really is that tcpdump doesn't show any problems. Here is an extract from "tcpdump -i any port 53" 09:13:38.283308 IP valine.aminocom.com.61815 ns-pri.ripe.net.domain: 14075 PTR? 166.225.58.95.in-addr.arpa. (44) 09:13:42.007410 IP gateway-eng.aminocom.com.37047 alanine.aminocom.com.domain: 35410+ PTR? 12.3.172.10.in-addr.arpa. (42) At the same time, the DNS log shows: Jul 22 09:13:38 gateway named[3487]: client 10.171.3.6#61300: view internal: error sending response: host unreachable Jul 22 09:13:40 gateway named[3487]: client 10.172.3.12#56230: view internal: error sending response: host unreachable Jul 22 09:13:40 gateway named[3487]: client 10.171.3.8#55221: view internal: error sending response: host unreachable Jul 22 09:13:49 gateway named[3487]: client 10.171.3.8#51342: view internal: error sending response: host unreachable So clearly at 09:13:40 there were two unsuccessful attempts to connect to internal machines (10.172.3.12 and 10.171.3.8, both are DNS servers), but nothing in the tcpdump output.

  Read the article

• Preventing Windows version of Vim from destroying other file systems permissions

  - by dborba

  I am currently using the windows version of gVim to edit source files on a networked drive mapped to a linux system, as well as local files created in cygwin. The problem is that the windows version of gVim destroys the original file permissions on the respective systems. IE: Files on cygwin are defaulted to 077. When edited by the windows version of vim they are saved as 777.This problem doesn't even occur when using ms-notepad (as well as all other editors I've tried), so I am not quite sure why gVim does it. A possible solution would be to use cygwin's gVim for everything, but that's rather cumbersome as it requires running an x11 environment to support it, and it causes some problems when running some commands from within gVim (or vim for that matter) when working on the networked drive. Any ideas how I might be able to maintain the existing file permissions? Edit: This morning while on a different machine the problem with cygwin did not occur. Cygwin & gVim were the same version, however the other machine is running WinXP while the machine the problem is occurring on runs Win7.

  Read the article

< Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >