Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 436/1359 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• How to restart WiFi interface without rebooting (it drops connection)?

  - by Dima

  I boot into ubuntu and it connects to the Wifi network fine. After about 10-15min the DNS stop resolving any website and a couple of minutes later network-managers tells me that I'm disconnected and tries to reconnect constantly to my router and fails to do it. Upon Ubuntu restart everything works fine for the first 10-15min again. When I boot into Mac OS X everything is fine with the same connection! How do I restart wifi interface? sudo ifdow wlan0 just tells me that wlan0 is not configured and wlan0 doesn't appear in /etc/network/interfaces either, which I find strange.... (unless network-manager is doing it behind my back).

  Read the article

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Chromebook C720 - issue suspending and booting

  - by user72727

  I recently bought an Acer C720 chromebook (Celeron, 2GB RAM, 16GB SSD) with the intention of loading Linux and using it as a cheap development laptop while on my holiday. The installation sort of went ok but initially the trackpad didn't work so I ran a script that mostly fixed that. My current issues are: Booting: it still goes to the chrome "unknown os" white screen - I have to press ctrl L - then escape then 1 then wait for 30 secs while it seems to be searching for something. Then Ubunto loads up fine. Any idea how to fix this? Suspend: if I close the lid of the laptop then it doesn't seem to suspend properly. At least when I open the lid the screen appears to be on but the screen is blank with a cursor. Nothing responds on the keyboard and I have to hold the power down to restart it. The suspend from the top menu has the same issue. Moving windows: I don't have a mouse click button so how do I move windows around the screen? Launcher bar: I've set mine to auto hide (which it does) but what exactly do you have to do to get it back? I just repeatedly jab the mouse at the side of the screen and eventually it pops up. I don't mind starting all over again but obviously a quick fix is preferred ;) Mike Ubunto 14.04.1 LTS Kernel 3.13.0-32-generic PS Sorry for so many questions.

  Read the article

• watchdog/0 process using all my CPU suddenly

  - by jeffery_the_wind

  I have a fresh installation of Ubuntu 12.04, I have been running it for about a week. Suddenly today I noticed my computer freezes every 5 seconds. I restarted the computer and I still get this. I believe it is a process called watchdog/0 that is using all the resources. See the attached pictures. How can I stop this? I can barely use my computer like this. UPDATE Well I just did a cold reboot, (shutdown, unplug, and plug back in, and turn on) and it seems to have fixed it. After looking at the man page for watchdog, it seems that this process may stay on during a restart? so it is more like a soft restart? Why that happens I don't know.

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• .bash_history and .cache

  - by John Isaacks

  I have a user who's home directory is a Mercurial repository. Mercurial notified me that there were 2 new unversioned files in my repository. .bash_history and .cache/motd.legal-displayed. I assume bash_history is the history of bash commands for my user. I have no idea what the other is. I don't want these files to be versioned by Mercurial, are they safe to just delete, or will they come back, or mess something up? Can they be moved to somewhere else? Or do I have to add them to my .hgignore file?

  Read the article

• FTP over ssh hangs on "Connection established: Waiting for Welcome Message"

  - by Siriss

  I have looked far and wide and have not quite found the answer. I am running ubuntu 11.10, openssh, and vsftpd. I am trying to configure my FTP to tunnel over ssh. My ssh connection works just fine and I can create the tunnel to my FTP port. When I go to use Filezilla to connect, it hangs at "Waiting for Welcome Message". I think it is an iptables issue, but I can't seem to figure out what needs to be changed. When I take iptables down, it connects just fine. I don't want to open any more external ports, just my one SSH port, and I can't seem to get it right on the internal port forwarding rule. I always end up opening it to the outside. I would love some help if anyone has any ideas and I hope I have made it clear. Thank you in advance!!

  Read the article

• Further question on Intel graphics driver

  - by Thomas Byers

  Ok, Josh answered almost immed.! I need to know specifically, now that I am using Nvidia card effectively, do I need to allow update manager to update the intel gr. drivers? I must add, I believe I know why Update Manager is telling me I need to update those Intel gr. drivers. It probably happened because I tried to update my nvidia drivers and got a buggy install, which let to to a black screen. I shut the system down manually after that and rebooted to a black screen and upon a further reboot I ascertained that I could still dual-boot(windows 7) into the other os. Then I went through the restart process and at the grub2 menu chose other options and it was probably, at that time, that Linux was smart enough to know that nvidia drivers as installed weren't cutting it, and reverted to the onboard Intel graphics system...does that make sense? Anyway, after successfully getting up and running, I reinstalled my old but successful nvidia drivers and all was well again, except now upon running Update Manager, I am offered the Intel graphics driver upgrade each time, which, up til now I have unchecked...my question is now more obvious. Should I accept the Intel driver update and if I do, will it once again override my nvidia drivers?

  Read the article

• How do I add English-UK thesaurus in LibreOffice?

  - by Chethan S.

  I have been trying to use English-UK thesaurus in LibreOffice but so far cannot get it to work. I have installed mythes-en-us as only it was available in repos. As suggested in some forums I searched for openoffice.org thesaurus, but again US version was available. As a result I can't enable thesaurus when I choose English UK: As instructed elsewhere I tried this: cd /usr/share/myspell/dicts sudo ln -s th_en_US_v2.dat th_en_GB_v2.dat sudo ln -s th_en_US_v2.idx th_en_GB_v2.idx Still the result is same as shown in above screenshots. What can be done now?

  Read the article

• transferring files from PC to Ubuntu PC on same network

  - by Travis

  i recently installed a fresh version of ubuntu 12.04 i wanted to transfer my old files from my pc that is running windows, to my other pc which now has ubuntu installed on it. They are both on the same network, i feel like this should be something easy to do, but i cant figure it out at all. Any help would be appreciated thank you. I downloaded and installed samba on my linux computer, and set up a share, but i can not find the directory on my windows machine. where do i find it?

  Read the article

• How to remove the black bar at the top of my screen?

  - by Casper Li

  The display area is not fit to my monitor(1440x900) and there is a black bar at the top of my screen. The bottom of the display area can't be displayed. How can I deal with this problem? Moreover, I don't know how to install my display card's driver(MSI R4770 Cyclone). Do I need to install it? Here are some related pictures : My monitor My monitor Displays xrandr Thank you for your attention

  Read the article

• How to convert a .pdf file into a folder of images?

  - by Shawn

  I have some .pdf files that I would like to convert to my preferred reading format of .cbr or .cbz or, if this isn't directly possible, I need to extract all pages from the .pdf as images and then compress them into my format of choice. I have only been able to save pages one at a time with Document Viewer. Obviously, I'd like to do it a little quicker. I have tried pdfsam, pdf shuffler, and pdfmod all with no luck. I am using Ubuntu 11.10.

  Read the article

• Does the latest version of Ubuntu (12.04) support Unity 3D?

  - by Douglas Combs

  I just installed the latest version of Ubuntu (12.04) 64bit. I am using a Radeon HD 7750 vid card. I think I have the Catalyst driver installed correctly. But when I go to system and look at the details, it shows that my graphics is VESA:01. Does this mean I it, I didn't correctly install my driver? System Specs: MB: ASUS P7P55-M CPU: Intel i5 Quad Core MEM: 4GB DD3 VC: HIS Radeon HD 7750 (1GB DDR5) Thanks for help.

  Read the article

• SMART says disk failure is imminent due to bad blocks, what do I need to do?

  - by flix

  I have on my hard drive 2 OSes: Ubuntu 12.04 and Windows Vista (I keep it just because of school). Everything was OK on both OSes, but one day on Ubuntu I was getting awkward noises from my notebooks' hard drive and then everything stopped and I couldn't do anything. On Windows everything was OK. Every time I boot Ubuntu I can get 5 minutes normal run time, without problems. After that the hard drive sounds crazy and nothing works. I could run S.M.A.R.T tests from a older Ubuntu CD (10.04) from the GUI (Disk Utility, or something like that and from terminal). From the GUI, I got that the DISK FAILURE IS IMMINENT and I have ~700 bad blocks (or broken blocks, I had that test I while ago) on my HDD. From the terminal (I don't remember if it was fsck or a SMART test command) I got that the HDD will fail in under 24 hours. Since then it passed 2-3 weeks. I've tried "badblocks" but after 10 hours it was still running and I had to stop it. Now I have to use cygwin and other alternatives for my Linux apps on Windows. How can I separate the bad blocks from Ubuntu so it wouldn't use them? Please help.

  Read the article

• Can't install gimp-plugin-registry

  - by Uri Herrera

  I tried to install the Ubuntu Studio Graphics meta-package, however it didn't install correctly.The package gimp-plugin-registry just won`t install, i tried the one in the Software center and the one on the WebUp8 PPA neither package works. The following NEW packages will be installed: gimp-plugin-registry 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/1395kB of archives. After this operation, 3592kB of additional disk space will be used. (Reading database ... 402557 files and directories currently installed.) Unpacking gimp-plugin-registry (from .../gimp-plugin-registry_3.2-1_i386.deb) ... dpkg: error processing /var/cache/apt/archives/gimp-plugin-registry_3.2-1_i386.deb (- -unpack): trying to overwrite '/usr/lib/gimp/2.0/plug-ins/file-xmc', which is also in package gimp 2.7.3-2010110501~mm dpkg-deb: subprocess paste killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/gimp-plugin-registry_3.2-1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Why do the interfaces show ipv6 address along with ipv4

  - by nixnotwin

  I have manually specified only ipv4 address for my interfaces. But all the interfaces automatically show inet6 address as well. Does it mean that ubuntu starts an ipv6 tunnel by default. If it does, isn't it dangerous, as ipv6 assigns public ips for all LAN clients. I only have a firewall on my NAT router, and my clients, who's interfaces show ipv6 address, do not have firewalls. Here is a screenshot: eth0 Link encap:Ethernet HWaddr 34:dc:47:2e:ad:13 inet6 addr: fe80::28cf:38ff:fb7b:da19/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5783 errors:0 dropped:0 overruns:0 frame:0 TX packets:6098 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:2961324 (2.9 MB) TX bytes:1573757 (1.5 MB) Interrupt:46 Note: For privacy reasons I have modified the HWaddr and inet6 addr values.

  Read the article

• Remove unwanted Mount option from Places Menu

  - by Jack

  On Ubuntu 10.10, I added a CIFS network share into /etc/fstab using /media/pub as my mount point. The share becomes visible on the Desktop and under Places (drive icon), which is what I want. But the problem is, Ubuntu 10.10 (unlike 10.04) creates another entry under Places with same name "pub", except this appears to be a mount shortcut rather than another link to the share. When I move my mouse over it says "Mount pub" and if I click on it, it will mount the share and again each time (if already mounted) - it does not display contents of share. In either case, an error pops up soon after "Unable to mount pub - Timeout waiting for mount to appear". The share itself is accessible, but I can't unmount via GUI, system reports its mounted multiple times and I have to unmount via terminal. (sudo umount -a) As I'm mounting the share at boot time, I don't need this manual option under Places. Is there an easy way to stop Ubuntu from listing it under Places? I have tried making the mount point under /mnt, this fixes the problem, except creates another as it removes the drive icon from Desktop and Places. I could create a bookmark, but just wondered if there's an easy fix to this unwanted entry under Places. Thanks

  Read the article

• Execure a random command from .txt file?

  - by Alberto Burgos

  I have a Ubuntu server, and I'm trying to print a Twitter quote using the app "twidge". So I made a list of tweets on a .txt file. I want to print one tweet (per line) from that file and send it to Twitter via twidge (or what ever other method was possible). I can print a random phrase with shuf: shuf -n 1 /var/www/tweets.txt and it works. It sends me back one of the tweets, but, it does not send it to Twitter, even if the "in line" phrase is a command. i.e: twidge update "bla bla bla" It just prints on the screen, but don't send it to Twitter. I tried turning the .txt to .sh, but don't work... any idea? by the way, i want to use it with crontab, something like this: 15 * * * * shuf -n 1 /var/www/tweets.txt

  Read the article

• Whenever I try to remove a Debian package I receive an Error

  - by Brenton Horne

  Whenever I type into the terminal the command: sudo dpkg -r '/home/brentonhorne/Downloads/virtualbox.deb' I receive the error: dpkg: error: --remove needs a valid package name but '/home/brentonhorne/Downloads/virtualbox.deb' is not: illegal package name in specifier '/home/brentonhorne/Downloads/virtualbox.deb': must start with an alphanumeric character Type dpkg --help for help about installing and deinstalling packages [*]; Use `dselect' or `aptitude' for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through `less' or `more' ! How do I get around this problem?

  Read the article

• Install wont boot up, stuck on loading text dots / restarts

  - by Franz Mayo Horkovic

  Friend gave me her laptop, we agreed on Ubuntu, but I have troubles even booting up live version (see the notebook). I tried 12.04 64bit on USB stick, it does nothing, when I choose booting live version, it just restarts PC. Then I tried 32bit version, it starts loading, but its stuck on loading components, printing on black screen just dots ........... I Googled it, found similar problem - somebody suggested to use older version and then upgrade it. I went through 11.04, 10.04 - 64 and 32 same result. Restart or infinite loading. I did memtest, it showed 4 errors, Windows Vista is running "fine", no "bluescreens" etc. Any ideas what am I doing wrong?

  Read the article

• How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

  - by Ivan Kreimer

  I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

  Read the article

• Where do lucid-updates come from?

  - by timbooo

  Considering the following command: # apt-get --simulate --show-upgraded upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: libimobiledevice0 libpam-ck-connector libparted0debian1 Inst libimobiledevice0 [0.9.7-1ubuntu1] (0.9.7-1ubuntu1.2 Ubuntu:10.04/lucid-updates) Inst libpam-ck-connector [0.4.1-3ubuntu1] (0.4.1-3ubuntu2 Ubuntu:10.04/lucid-updates) Inst libparted0debian1 [2.2-5ubuntu5.1] (2.2-5ubuntu5.2 Ubuntu:10.04/lucid-updates) [...] I can read an Inst line as the following: Inst <package> [<oldversion>] (<newversion> Ubuntu:10.04/lucid-updates) Can someone tell me where the Ubuntu:10.04/lucid-updates comes from? - Considering an own repository, how is this configurable?

  Read the article

• Deleting Unused Swaps Partions

  - by Nikita Kononov

  Good evening everyone , I got a little issue with Swap Partitions. Due to some issues after installing Ubuntu first time, I reinstalled it and now I have 3 Swaps. Here is sudo fdisk -l result Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xaa9693fe Device Boot Start End Blocks Id System /dev/sda1 2048 52430847 26214400 1c Hidden W95 FAT32 (LBA) /dev/sda2 * 52430848 540677076 244123114+ 7 HPFS/NTFS/exFAT /dev/sda3 540678142 1465147391 462234625 5 Extended Partition 3 does not start on physical sector boundary. /dev/sda5 1452750848 1465147391 6198272 82 Linux swap / Solaris /dev/sda6 1440352256 1452742655 6195200 82 Linux swap / Solaris /dev/sda7 540678144 1427951615 443636736 83 Linux /dev/sda8 1427953664 1440339967 6193152 82 Linux swap / Solaris So Swaps in /dev/sda5 and /dev/sda6 are no longer in use as far as I understand and thus I was planning to delete them, however faced a problem. What I did is download and burn Gparted Live CD and boot it up, tried to delete those partitions but I have no idea how to add 12GB unallocated memory to the existing OS partition in this case to /dev/sda7 Is there anyway I can delete 2 swaps and extend unallocated memory to /dev/sda7 partion? Thank you in advance!

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Dealing with three Windows partitions in dual boot installation

  - by Tim

  For dual-boot installation of Ubuntu after Windows. Quoted from ubuntuguide If a Windows boot partition exists as a second NTFS partition, it should be left alone. If there is a Windows recovery partition also installed, it can also be left alone as long as there are only two NTFS partitions total on the hard drive (i.e. there is no NTFS boot partition as well). If there are a total of 3 NTFS partitions on the hard drive, then the third Windows NTFS partition (the recovery partition) should be removed after creating Recovery CDs from it (see here). In the last case where Windows has three partitions, I was wondering why it says the recovery partition shall be removed? Is it possible to keep the three and create another extended partition with several logical partitions for installing Ubuntu and dual-booting the two OSes? I plan to dual-boot install Ubuntu 10.04 with existing Windows 7. Following is the layout of the current partitions of my hard drive viewed from Windows 7: So must I remove the Lenovo_Recovery (Q:) partition for the same reason you give for the first question? Thanks and regards!

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >